BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Office Laboratory (NROL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- [email protected]

Scope List

Reset

290 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

121

IS 8462 (1977)

Specification for sterilizer, portable, vertical, pressure type

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Shape and Dimensions)	-
4.2 (Thickness)	-
5.8 (Construction)	-
6.1 (Workmanship and Finish)	-
6.2 (Workmanship and Finish)	-
8.1 (Proof Pressure Test)	-

Partial

-
-

122

IS 8329 (2000)

Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 10 (Hardness & Tensile Test)	-
Cl 11 (Hydrostatic Test)	-
Cl 13 (Length, Diameter, Wall Thickness & Ovality)	-

Partial

-
-

123

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 8 (Press)	-
Cl 9 (Strainage Embrittlement)	-
Cl 13 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 (Nitrogen%)	-

Partial

-
-

124

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.1 (Diameter of Core Wire)	-
7.1.2 (Length of Electrodes)	-
7.2.1 (Contact End)	-
7.2.2 (Arc striking End)	-
7.3 (Concentricity of Flux covering with core wire)	-
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-
9.1.2 Table 6 ( Yield Stress -Annex F)	-
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-
9.2 (Butt Weld Bend Test-IS 1599)	-
6 & 8.2 (Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-

Partial

-
-

125

IS 2061 (1995)

Bicycle - Front forks - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (MARKING)	-
3 (Material)	-
4 (Dimensions)	-
5 (. Manufacturer&Finish)	-
7.1.1 ( i) Load test )	-
7.1.2 (ii) Expansion Tes )	-
7.1.3 (iii) Tests for Finish)	-
7.1.4 (iv) Impact Test)	-
7.1.3 (iii) Tests for Finish)	-

Complete

-
-

126

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Nominal Diameter & Out Of Shape)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

Partial

-
-

127

IS 6595 : Part 1 (2018)

Horizontal centrifugal pumps for clear, cold water - Specification: Part 1 agricultural and rural water supply purposes (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Pump Test Verification of the Guarantee Cl.9.4 of IS 9137:2019 Cl. 9.4.1 Curves QH and Qη)	-
11.1 (Guarantee of Workmanship & material)	-
10.1 (Pump Test Verification of the Guarantee Cl.9.4 of IS 9137:2019 Cl. 9.4.1 Curves QH and Qη)	-
10.1 (Pump Test Verification of the Guarantee Cl.9.4 of IS 9137:2019 9.4.2 Efficiency)	-
10.1 (Pump Test Verification of the Guarantee Cl.9.4 of IS 9137:2019 9.4.3 Pump Power Input)	-
10 (Pump Test Verification of guarante Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-
10 (Pump Test Verification of guarante Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-
10 (Pump Test Verification of guarante Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-
12.2.2 (Pump Power Input )	-

Complete

-
-

128

IS 13334 : Part 2 (2014)

Skimmed milk powder - Specification: Part 2 extra grade (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (i) (Moisture (IS 116231or 16072))	-
Table 1 (v) (Total ash (on dry basis), Annex B of IS 14433)	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (iii) (Milk fat (IS 117213) or Annex B)	-
Table 1 (viii) (Scorched particles (equivalent to Disc B) (IS 13500))	-
Table 1 (ix) (Bacterial count (IS 5402))	-
Table 1 (x) (Coliform count (IS 5401 - Part 1))	-
Table 1 (xi) (Escherichia coli (IS 5887 - Part 1))	-
Table 1 (xii) (Coagulase positive Staphylococcus aureus (IS 5887 - Part 2))	-
Table 1 (xiii) (Salmonella (IS 5887 - Part 3))	-
Table 1 (xiv)(a) (Spore Count: a) Aerobic (Bacillus cereus) Type M (IS 5887 - Part 6))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type m (ISO 15213 : 2003))	-
Table 1 (xv) (Listeria monocytogenes (IS 14988 - Part 2 : 2001))	-

Partial

-
-

129

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Heat Treatment)	-
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 10 (Diameter & Out Of Round)	-

Partial

-
-

130

IS 1970 (1995)

Cropprotection equipment - Hand - Operated compression - knapsack sprayer - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.1 (Tank & Skirt)	-
Cl 6.2 (Strap)	-
Cl 6.3 (Filler Ring)	-
Cl 6.4 (Pump Cylinder)	-
Cl 6.5 (Piston)	-
Cl 6.6 (Piston Rod)	-
Cl 6.7 (Handle)	-
Cl 6.8 (Valve Assembly)	-
Cl 6.9 (Delivery pipe)	-
Cl 6.10 (Threaded connections)	-
Cl 6.11 (Delivery Outlet)	-
Cl 6.13 (Delivery Hose)	-
Cl 6.14 (cut Off device & Lance)	-
Cl 6.15 (Nozzle)	-
Cl 6.16 (Adoptor & cap)	-
Cl 6.17 (Height)	-
Cl 6.18 (Mass)	-
Cl 6.19 (Endurance)	-

Complete

-
-

131

IS 784 (2019)

Prestressed concrete pipes (Including Specials) - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.4 (Circumferential Prestressing)	-

Partial

-
-

132

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Minimum Thickness)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Minimum Socket Length)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Mean Socket Internal Diameter at Mid-Point of Socket Length)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Out-of-roundness tolerances of socket inside diameter)	-
Cl. 6.1 (Stress Relief Test- Appendix A)	-
Cl. 6.4 (Short-Term Hydraulic Test- Appendix D)	-

Partial

-
-

133

IS 7466 (1994)

Rubber gaskets for pressure cookers - Specifications (First Revison)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Workmanship and Finish )	-
3.4-Table 1(ii) (Requirements of Rubber Used for Gaskets-Tensile strength,)	-
3.4-Table 1(iii) (Requirements of Rubber Used for Gaskets-Elongation at break)	-
3.4-Table 1(iv-b) (Requirements of Rubber Used for Gaskets-Tensile strength(After ageing 3 days in Aie-oven Change From Original Value))	-
3.4-Table 1(iv-c) (Requirements of Rubber Used for Gaskets-Elongation at break(After ageing 3 days in Aie-oven Change From Original Value))	-

Partial

-
-

134

IS 7452 (1990)

Hot rolled steel sections for doors, windows and ventilators - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 6 (Dimensions)	-
cl 7 (MASS AND MASS TOLERANCE)	-
cl 9 (BEND TEST)	-
cl 8 (SURFACE FINISH)	-

Complete

-
-

135

IS 1538 (1993)

Cast iron fittings for pressure pipes for water, gas and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (The metal used for the manufacture of pipe shall be of a quality not less than that specified for grade FG 150 of IS 210 )	-
5.1 (tensile strength)	-
6.1 (Brinell hardness tests)	-
8 (Hydrostatic Test)	-
9.1,Table 2 & 3 (DI)	-
9.1,Table 2 & 3 (P)	-
9.1,Table 2 & 3 (g)	-
9.1,Table 2 & 3 (h)	-
9.1,Table 2 & 3 (K)	-
9.1,Table 2 & 3 (L)	-
9.1,Table 2 & 3 (M)	-
9.1,Table 2 & 3 (N)	-
9.1,Table 2 & 3 (f)	-
9.1,Table 4 (D)	-
9.1,Table 4 (a)	-
9.1,Table 4 (b)	-
9.1,Table 4 (s)	-
9.1,Table 4 (r)	-
9.1,Table 5 (D)	-
9.1,Table 5 (g)	-
9.1,Table 5 (a)	-
9.1,Table 5 (b)	-
9.1,Table 5 (c)	-
9.1,Table 5 (f)	-
9.1,Table 5 (s)	-
9.1,Table 5 (C)	-
9.1,Table 6 (Holes No)	-
9.1,Table 6 (Holes diameter)	-
9.1,Table 6 (Diameterof Bolts)	-
9.1&11.1,Table 7,8&9 (e)	-
9.1&11.1,Table 7,8&9 (l)	-
9.1&11.1,Table 10 to13 (Mass (Approx))	-
9.1&11.1,Table 10 to13 (e)	-
9.1&11.1,Table 10 to13 (r)	-
9.1&11.1,Table 10 to13 (a)	-
9.1&11.1,Table 10 to13 (b)	-
9.1&11.1,Table 10 to13 (Mass (Approx))	-
9.1&11.1,Table 15 (e)	-
9.1&11.1,Table 14 (Nominal Diameter)	-
9.1&11.1,Table 15 (e1)	-
9.1&11.1,Table 14 (l)	-
9.1&11.1,Table 14 (h)	-
9.1&11.1,Table 24 (Mass (Approx))	-
9.1&11.1,Table 25 (e)	-
9.1&11.1,Table 25 (l)	-
9.1&11.1,Table 24 (h)	-
9.1&11.1,Table 25 (Mass (Approx))	-
9.1&11.1,Table 26 (e1)	-
9.1&11.1,Table 26 (h1)	-
9.1&11.1,Table 26 (Nominal Diameter)	-
9.1&11.1,Table 26 (e2)	-
9.1&11.1,Table 26 (l2)	-
9.1&11.1,Table 26 (l3)	-
9.1&11.1,Table 26 (l)	-
9.1&11.1,Table 26 (Mass (Approx))	-
9.1&11.1,Table 27 (dn)	-
9.1&11.1,Table 27 (e1)	-
9.1&11.1,Table 27 (b)	-
9.1&11.1,Table 27 (l3)	-
9.1&11.1,Table 27 (l2)	-
9.1&11.1,Table 27 (e2)	-
9.1&11.1,Table 27 (r)	-
9.1&11.1,Table 27 (l1)	-
9.1&11.1,Table 27 (Mass)	-
9.1&11.1,Table 28 (D)	-
9.1&11.1,Table 28 (t)	-
9.1&11.1,Table 28 (Mass (Approx))	-
12.1 to 12.7 (Coating )	-

Partial

-
-

136

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 11 (Workmanship)	-
Cl 12 (Length, Width & Thickness)	-
Cl 13 (Workmanship)	-

Complete

-
-

137

IS 1566 (1982)

Specification for hard - Drawn steel wire fabric for concrete reinforcement (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (DIMENSIONS)	-
7 (SIZES OF SHEETS ‘OR ROLLS)	-
8 (MASS)	-
9.2 (Tolerance on Size of Mesh)	-
9.3 (Tolerance on Size of Sheet)	-
9.4 (Tolerance on Mass of Fabric)	-
10 (MECHANICAL PROPERTIES)	-
11.2 (Tensile Test)	-
11.3 (Reverse Bend Test)	-

Partial

-
-

138

IS 4397 (1999)

Cold - Rolled carbon steel strips for ball and roller bearing cages retainers - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Freedom from defects )	-
8 ( Bend Test )	-
9 (Hardness-IS 1500: Pt 1)	-
14 ( ROLLING TOLERANCES)	-

Partial

-
-

139

IS 1537 (1976)

Specification for vertically cast iron pressure pipes for water, gas and sewage (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 , 6 of IS 210 ( The composition of cast iron shall be left to the discretion of the manufacturer)	-
4.1 (Tensile Strength)	-
4.2 (Hardness test)	-
6.1 (Hydrostatic test)	-
7.1 & Table 2 (DE)	-
7.1 & Table 2 (DI)	-
7.1 & Table 2 (P)	-
7.1 & Table 2 (g)	-
7.1 & Table 2 (h)	-
7.1 & Table 2 (DC)	-
7.1 & Table 2 (c)	-
7.1 & Table 2 (f)	-
7.1 & Table 3 (DI)	-
7.1 & Table 3 (P)	-
7.1 & Table 3 (g)	-
7.1 & Table 3 (h)	-
7.1 & Table 4 (D)	-
7.1 & Table 4 (a)	-
7.1 & Table 4 (b)	-
7.1 & Table 4 (s)	-
7.1 & Table 4 (r)	-
7.1 & Table 5 (D)	-
7.1 & Table 5 (C)	-
7.1 & Table 5 (Holes Number)	-
7.1 & Table 5 (Holes Diameter)	-
7.1 & Table 5 (Diameter of Bolts)	-
7.1 & Table 6 to 8 (DE)	-
7.1 & Table 6 to 8 (t)	-
7.1 & Table 6 to 8 (Mass of one meter barrel (Approx))	-
7.1 & Table 6 to 8 (Socket mass (Approx))	-
7.1 & Table 6 to 8 (Total mass for one working length in meter)	-
8.4 (Permissible deviation from a straight line)	-
9.1,Table 9 (DE)	-
9.1,Table 9 (e)	-
9.1,Table 9 (Flange, Mass of one meter (Approx))	-
9.1,Table 9 (Mass of one flange (Approx))	-
9.1,Table 9 (Working Length)	-
10.1 to 10.6 (Coating )	-
3.1 , 6 of IS 210 ( The composition of cast iron shall be left to the discretion of the manufacturer)	-
7.1 & Table 5 (Holes Number)	-

Partial

-
-

140

IS 1971 (1996)

Crop protection equipment - Hand - Operated stirrup - Specifation (Fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Classification)	-
Cl 6.1 (Discharge rate)	-
Cl 6.2 (Volumetric Efficiency)	-
Cl 6.1 (Discharge rate)	-
Cl 6.3 (Endurance)	-
Cl 7.1 (Height)	-
Cl 7.2 (Total Mass)	-
Cl 7.3 (Pump Cylinder)	-
Cl 7.4 (Piston)	-
Cl 7.5 (Piston rod)	-
Cl 7.6 (handle)	-
Cl 7.7 (Guide & Gland Packing)	-
Cl 7.8 (Foot Valve)	-
Cl 7.9 (Stirrup & Foot Resr)	-
Cl 7.10 (Threaded connections)	-
Cl 7.11 (Delivery Spout)	-
Cl 7.13.1 (Delivery Hose)	-
Cl 7.13.2 (Hosed connections)	-
Cl 7.13.3 (cut Off device & Lance)	-
Cl 7.13.4 (Nozzle)	-

Complete

-
-

141

IS 1536 (2001)

Centrifugally cast (Spun) iron pressure pipes for water, gas and sewage - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.2, annex-A (Tensile Test ( for pipes over 300mm))	-
11.3 (Brinell Hardness Test)	-
13.3 Table 3 (DE)	-
13.3 Table 3 (DI)	-
13.3 Table 3 (p)	-
13.3 Table 3 (g)	-
13.3 Table 3 (a(optional))	-
13.3 Table 3 (h)	-
13.3 Table 3 (K)	-
13.3 Table 3 (L)	-
13.3 Table 3 (M)	-
13.3 Table 3 (f)	-
13.3 Table 3 (N)	-
13.3 Table 4 (DE)	-
13.3 Table 4 (X)	-
13.3 Table 4 (DI)	-
13.3 Table 4 (P)	-
13.3 Table 4 (Q)	-
13.3 Table 4 (I)	-
13.3 Table 4 (J)	-
13.3 Table 4 (K)	-
13.3 Table 4 (N)	-
13.3 Table 4 (O)	-
13.3 Table 4 (S)	-
13.3 Table 4 (T)	-
13.3 Table 4 (L)	-
13.3 Table 4 (M)	-
13.4 Table 5 (c)	-
13.4 Table 5 (D)	-
13.4 Table 5 (E)	-
13.4 Table 5 (b)	-
13.4 Table 5 (a)	-
13.4 Table 5 (r)	-
13.4 Table 5 (s)	-
13.4 Table 5 (Holes Number)	-
13.4 Table 5 (Holes Diameter)	-
13.4 Table 5 (Diameter of Bolts)	-
13.5 Table 6 to 8 (DE Lead joint)	-
13.5 Table 6 to 8 (DE Push on joint)	-
13.5 Table 6 to 8 (e)	-
13.6 Table 9 (DE)	-
13.6 Table 9 (e)	-

Partial

-
-

142

IS 14846 (2000)

Sluice valve for water works purposes (50 To 1200 mm size) - specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Nominal Sizes)	-
5.1.1 (Actual Bore)	-
6 (Material)	-
7.2.1 (Manufacture - Bodies and Bonnets)	-
7.2.2 (Manufacture - Bodies and Bonnets)	-
7.2.3 (Manufacture)	-
7.2.4 (Manufacture)	-
7.3 Table 3A 1 (Flanges)	-
7.3 Table 3A 2 (Flanges)	-
7.3 Table 3A 3 (Flanges)	-
7.3 Table 3A 4 (Flanges)	-
7.3 Table 3A 5 (Flanges)	-
7.3 Table 3A 6 (Flanges)	-
7.4.1 (Wedges )	-
7.4.1 (Wedges)	-
7.4.1 (Wedges)	-
7.4.2 (Wedge Faces)	-
7.5 (Guides and Lugs)	-
7.5.1 (Guides and Lugs)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,4 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,5 (Dimension of Stem and Wedge Nuts)	-
7.7.2 (Stem and Wedge Nuts)	-
7.7.3 (Stem and Wedge Nuts)	-
7.7.4 (Stem and Wedge Nuts)	-
7.9 (Height of Valve)	-
7.11 (Hand Wheel)	-
7.11 (Hand Wheel)	-
7.11 (Hand Wheel)	-
7.12 (Valve Caps)	-
7.12 (Valve Caps)	-
7.12 (Valve Caps)	-
7.12 (Valve Caps)	-
7.13 Table 2, 3 (Stuffing Box )	-
7.13 Table 2, 3 (Stuffing Box )	-
7.13 Table 2, 3 (Stuffing Box )	-
7.13 Table 2, 3 (Stuffing Box )	-
7.14 (By Pass Arrangements)	-
7.14 (By Pass Arrangements)	-
8 (Accessories or Optical Features)	-
9 (Coating)	-
10.1 Annex B-1 (Hydraulic Test)	-
10.1 Annex B-2 (Hydraulic Test)	-
10.2 (Flaw Detection Test for Stems)	-

Complete

-
-

143

IS 7312 (2018)

Welded and seamless steel dissolved acetylene gas cylinders - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9,9.1 (VALVES AND VALVES PAD)	-
9.2 (Valve Protection The valve shall be protected by a stout metal cap perforated for ventilation and of thickness not less than 3.5 mm, screwed on to the neck, or in any other manner approved by the statutory authority.)	-
10,10.1 (FITTINGS OTHER THAN VALVES Footring)	-
10,10.1 (FITTINGS OTHER THAN VALVES Footring )	-
14 (CHECKING OF WATER CAPACITY The water capacity of the cylinders shall be checked. This shall be done by weighing or by volumetric method. Water capacity of the cylinder shall have atolerance of + 3/-0 percent on the declared value. )	-
15.1 IS 3196(Part 3) (Hydrostatic Stretch Test: Permanent volumetric expansion suffered by the cylinder due to application of test pressure shall not exceed 7.5 percent of the total volumetric expansion at the pressure.)	-
15.2 IS 3196(Part 3) (Hydrostatic Test)	-
16 IS 3196(Part 3) (Pneumatic Leakage Test)	-
17 IS 3196(Part 3) (BURST TEST)	-
18a IS 3196(Part 3) (a)Parent metal Longitudinal specimen Tensile Strength )	-
18b IS 3196(Part 3) ( Yield Stength )	-
18f IS 3196(Part 3) (Elongation )	-
18c IS 3196(Part 3) (Elongation )	-
18g IS 3196(Part 3) (c)Weld Joint test specimen)	-
18h IS 3196(Part 3) (c)Weld Joint test specimen)	-
18j IS 3196(Part 3) (d)Bend test Across weld Root Bend test,)	-
18k IS 3196(Part 3) (Face Bend test,)	-
18p IS 3196(Part 3) (f) Minimum Thickness test: The thickness shall not be less than agreed finished thickness,Declared thicknes:)	-
20.5 (Backfire Test)	-

Partial

-
-

144

IS 14756 (2017)

Stainless steel cookware - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Shape and Dimension,)	-
4.2 (Thickness)	-
5.1 (Workmanship And Finish)	-
5.2 (Workmanship And Finish)	-
5.3 (Workmanship And Finish)	-
5.4 (Workmanship And Finish)	-
6.2 (Mechanical Shock Test (for cladded utensils only))	-

Partial

-
-

145

IS 12817 (2013)

Stainless steel butt hinges - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2, Table 1 to 6 (Length , A -IS 12817)	-
6.2, Table 1 to 6 (Breadth, B-IS 12817)	-
6.2, Table 1 to 6 (Breadth, B1-IS 12817)	-
6.2, Table 1 to 6 (Breadth, B2-IS 12817)	-
6.2, Table 1 to 6 (Thickness of flap, C-IS 12817)	-
6.2, Table 1 to 6 (Dia. of Hinge pin, D-IS 12817 )	-
6.2, Table 1 to 6 (Number of Knuckles- IS 12817 )	-
6.2, Table 1 to 6 (Number of Screw Holes -IS 12817 )	-
6.2, Table 1 to 6 (Holes for Screw Number- IS 12817 )	-
7.1 (General - IS 12817 )	-
7.2 (Knuckles - IS 12817 )	-
7.3 (Pins- IS 12817 )	-
7.4 (Screw Holes- IS 12817 )	-
7.4.2 (Position of screw holes - IS 12817 )	-
7.4.2, Fig 1 (The distance of the screw holes from the end of the flap - IS 12817 )	-
8 (Finish - IS 12817 )	-

Complete

-
-

146

IS 1783 : Part 1 (2014)

Drums large, fixed ends - Specification: Part 1 grade A drums (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Capacity)	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
6 (Material)	-
7.1 (Construction)	-
7.2 (Construction)	-
7.3 (Construction)	-
7.4 (Construction)	-
7.5 (Construction)	-
7.6 (Construction)	-
8 (Finish )	-
9.3 (Hydraulic Pressure Test)	-
9.2 (Drop Test)	-

Partial

-
-

147

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Grade)	-
3 (Type/Shape of Cover)	-
4.4 (Reinforcement)	-
4.4 (Reinforcement)	-
4.5 (Steel Fibres - Diameter / equivalent diameterofsteel tibres)	-
4.5 (Steel Fibres - The aspect ratio of the tibres)	-
5.2 and Table 1 (Dimensions of Frame - A)	-
5.2 and Table 1 (Dimensions of Frame - B)	-
5.2 and Table 1 (Dimensions of Frame - C)	-
5.2 and Table 1 (Dimensions of Frame - D)	-
5.2 and Table 1 (Dimensions of Frame - E)	-
5.2 and Table 1 (Dimensions of Frame - F)	-
5.2 (Dimensions of cover- Diameter)	-
5.2 (Clearance at top between the frame and the cover all round the periphery)	-
5.2 (Top surface ofthe frame and cover is in level)	-
5.2 (Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-
5.2 and Fig 1 (Clear cover to reinforcement)	-
5.2 and Fig 1 (Distance of housing from the edge)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.2 (Edge Protection and Finishing - Cover)	-
8 (LIFTING HOOKS)	-
9.1 (General)	-

Partial

-
-

148

IS 2785 (1979)

Specification for natural cheese (Hard Variety), processed cheese, processed cheese spread and soft cheese (First Revision)

- View breakup
Rs 3000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3.1 (Appearance)	-
3.3.2 (Odour and Flavour)	-
3.3.3 (Texture and Consistency)	-
3.3.4- Table 1-i (Moisture- Annex A)	-
3.3.4- Table 1-ii (Milk fat ( on dry basis)- Annex B)	-
3.3.4- Table 1-iii (Salt ( added sodium chloride)- Annex C)	-
3.3.4- Table 1-i (Moisture- Annex A)	-

Complete

-
-

149

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1, Table 2 (Tensile Strength- IS 1816)	-
Cl. 5.1, Table 2 (Elongation on 50 mm or 5.65√So Gauge Length)	-

Partial

-
-

150

IS 3419 (1988)

Specification for fittings for rigid non - Metallic (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 & 5 (Visual Examination -IS:3419)	-
6.2 & 9.1- Table-1, ii (Inside Diameter of Collar for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-1, iii (Inside Diameter of Ridge for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-1, iv (Minimum overall length for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-1, v (Minimum wall thickness for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, ii (Inside Diameter of Collar for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, iii (Inside Diameter of Ridge for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, iv (Minimum overall length (a) for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, v (Minimum overall length (l) for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, vi (Minimum wall thickness for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, ii (Inside Diameter of Collar(d6) for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, iii (Inside Diameter of Collar (d5) for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, iv (Inside Diameter of Ridge for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, iv (Minimum length for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, vi (Minimum wall thickness for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-4, ii (Outside Dameter of Normal type bend -IS:3419)	-
6.2 & 9.1- Table-4, iii (Minimum Inside Diameter of Normal Type Bend -IS:3419)	-
6.2 & 9.1- Table-4, v (Length (l1) of Normal Type Bend -IS:3419)	-
6.2 & 9.1- Table-5, ii (Outside Dameter of Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, iii (Minimum Inside Diameter of Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, iv (Inside Diameter of collar for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, v (R- for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, vi (Y- for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, vii (l2- for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-6, ii (Inside Diameter of collar for Normal type Elbows -IS:3419)	-
6.2 & 9.1- Table-6, iii (Length (l) of Normal Type Elbows -IS:3419)	-
6.2 & 9.1- Table-6, iv (Radious(r) of Normal Type Elbows -IS:3419)	-
6.2 & 9.1- Table-6, v (Minimum wall thicknes of Elbows -IS:3419)	-
6.2 & 9.1- Table-7, ii (Inside Diameter of Collear for Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-7, iii (Length (l) of Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-7, iv (Radious(r) of Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-7, v ( Minimum wall thicknes of Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-8, ii (Inside Diameter of Collear for socketed type Tees - IS:3419)	-
6.2 & 9.1- Table-8, iii (a - of socketed type Tees -IS:3419)	-
6.2 & 9.1- Table-8, iv (l - of socketed type Tees -IS:3419)	-
6.2 & 9.1- Table-8, v (Minimum wall thicknes of socketed type Tees -IS:3419)	-
6.2 & 9.1- Table-9, ii (B - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, iii (C - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, iv (D - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, v (E - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, vi (F(Max) - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, vii (F(Min) - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, viii (G - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, ix (t - of spout Type Circular Boxes -IS:3419)	-
10 (Resistance to Heat -IS:3419)	-
11 (Resistance to Burning - IS 3419)	-
12 (Moisture Absorption - IS 3419)	-
14.1 (Copper Test - IS 3419)	-
15, 15.3 (Resistance to Oil - IS 3419)	-
15,15.4 (Resistance to Oil - IS 3419)	-
16- Appendix-A (Resistance to Impact -IS 3419)	-
17.2 (Electric Strength - IS 3419)	-
17.3 (Insulation Resistance - IS 3419)	-

Complete

-
-

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Office Laboratory (NROL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- [email protected]

Scope List