BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Office Laboratory (NROL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- [email protected]

Scope List

Reset

290 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

181

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8,Table 6 (Hardness Test - IS 1500(Pt -1))	-
9, Table 5 (Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-
13.1&13.2&13.3 (Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-
5 (Freedom from defects , IS 5517)	-

Partial

-
-

182

IS 5290 (1993)

Landing valves - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, 5.1 (a) fig-1, type A (Types AND DIMENSIONS)	-
5, 5.1 (b) fig-2, type B (Types AND DIMENSIONS)	-
5.2 (Types AND DIMENSIONS)	-
5.2.1 (Types AND DIMENSIONS)	-
7, 7.1 (7 PERFORMANCE REQUIREMENTS, Water Tightness Test for the Valve)	-
7, 7.2 (hydrostatics pressure tests)	-
7, 7.3 (Flow test, pressure 7 kgf/cm2)	-
6, 6.1 (Finish)	-
6, 6.2 (Finish)	-

Partial

-
-

183

IS 5312 : Part 1 (2004)

Swing Check Type Reflux (Non-Return] Valves for Water Works Purposes - Part 1 : Single-Door Pattern

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 (Actual bore)	-
6.2 (Manufacture Dimensions Table 2 )	-
6.2 (Manufacture Dimensions Table 2 )	-
7.1 (Coating)	-
8.2 (Hydrostatic Body Test )	-

Partial

-
-

184

IS 781 (1984)

Specification for cast copper alloy screw down bib taps and stop valves for water services (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Dimensions & Tolerances)	-
Cl 7 (MINIMUM MASS)	-
Cl 9 (Testing)	-

Partial

-
-

185

IS 6006 (2014)

Uncoated stress relieved strand for prestressed concrete - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Weight)	-
Cl 7 (Tensile Test On UTM)	-
Cl 4 (Length )	-
Cl 4.5 (Workmanship)	-
Cl 4.5 (Workmanship)	-
Cl 4.5 (Workmanship)	-
Cl 4.5 (Workmanship)	-
4.1.2 (sulphur)	-
4.1.2 (phosphorus)	-

Partial

-
-

186

IS 3575 (1993)

Bitumen drums - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Closure (Figure 2))	-
7.1 (Finish)	-
7.2 (Finish)	-

Partial

-
-

187

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1,Table 4&Table 6 (Tensile Test - IS 1608(Pt -1))	-
10.2,Table 4&Table 5 (Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-
17 (Dimension and tolerance)	-
6 (Freedom from defects , IS 6911)	-
15 (Surface Finish)	-

Partial

-
-

188

IS 903 (1993)

Specification for Fire Hose Delivery Couplings, Branch Pipe, Nozzles And Nozzle Spanner - Specificaion

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Finish and workmanship)	-
4 (Marking)	-
6 (Branch pipe)	-
6.3 (Hydraulic test requirement)	-
7 (Nozzle)	-
7.3 (Hydraulic test requirement)	-
5 (Delivery hose coupling)	-
5.3 (Size and Dimension )	-
5.4 (Hydraulic test requirement)	-

Complete

-
-

189

IS 3502 (2009)

Steel chequered plates (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 5 (Workmanship)	-
Cl 6 (Workmanship)	-

Complete

-
-

190

IS 1038 (1983)

Specification For Steel Doors, Windows And Ventilators

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1. (Size-Height)	-
4.1 (Size-Width)	-
6.2 (Side Hung Shutter-Width of hinge)	-
6.2 (Side Hung Shutter- Thickness of hinge)	-
6.2 (Side Hung Shutter- Pin diameter)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate- Thicknesss of handle)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate-Height of handle plate)	-
6.2.3 (Peg Stay - Thickness)	-
6.2.3 (Peg Stay )	-
6.3 (Top Hung Ventilator-Thickness of hinge)	-
6.3 (Top Hung Ventilator-Pin diameter)	-
6.3 (Top Hung Ventilator-Width of hinge)	-
4.3 (Designation)	-
9 (Glazing- No of glazing clip against each plate)	-
8 (Finish)	-
7.2 Table 2 (Position of Fixing Screws)	-
7.1 (Position of Holes)	-
6.3 (Top Hung Ventilator)	-
6.1.1.1 (Visual Inspection Test)	-
6.1.1.2 (Macro Examination)	-
6.1.1.3 (Micro Examination)	-
6.2 (Side Hung Shutter)	-
5 (Material-Rolled Steel Section)	-
5 (Material-Coupling Section)	-
5 (Material-Glass Panels)	-
5 (Material-Screws)	-

Partial

-
-

191

IS 7092 : Part 2 (1987)

Specification for aluminium alloy tube for irrigation purposes: Part 2 extruded tube (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.6.2 (Ultimate Tensile Strength- IS 2657)	-
Cl. 6.4 (Hydrostatic Pressure Test-Cl. 6.4)	-
Cl.7.1, Table 2 (Outside Diameter-)	-
Cl.7.1, Table 2 (Wall Thickness)	-
Cl. 7.2 (Length)	-
Cl.4 (Workmanship & Finish)	-

Partial

-
-

192

IS 6218 (2008)

Bicycle - Mudguards - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause-3 (Carbon)	-
Clause-3 (Sulphur)	-
Clause-3 (Phosphorus)	-
Clause-3 (Silicon)	-
Clause-3 (Nitrogen)	-
Cl 5.3(Mech) (The wraping of the mudguard shall lie within the limits )	-
Cl 5.1(Mech) (The paint shall not soften,peel off or show any change in colour after the test.)	-
Cl 4.3(Mech) (The painted part shall be free from wrinkles, blisters,unevenness,scratch marks and other injurious defects.)	-
Cl 4.2(Mech) (The mudguard shall be free from manufacturing defects and shall be chemically phosphated and and stove enamelled , spray painted or otherwise finished to give a glossy finish .)	-
Cl 4.1(Mech) (Thickness of steel strip)	-
Cl 4.1(Mech) (Depth of mudguard)	-
Cl 4.1(Mech) (Width of mudguard )	-
Cl 4(Mech) (Manufacture ,Workmanship ,& Finish )	-

Complete

-
-

193

IS 455 (2015)

Portland slag cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 Table 1 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 Table 1 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 Table 1 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 Table 1 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 Table 1 iii a (Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-
7 Table 1 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 Table 1 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 Table 1 i (Fineness IS 4031(Part 2))	-
6 - Table - 1 vii ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6 - Table - 1 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 v (Loss on ignition - Cl 6.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 6.8 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 6.9 of IS 4032:1985)	-

Partial

-
-

194

IS 6003 (2010)

Indented Wire For--Prestressed Concrete ”

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1.2 (Weight)	-
Cl 7.1 (Tensile Test On UTM)	-
Cl 7.3 (Reverse Bend Test)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-

Partial

-
-

195

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 (Tensile Test-1608:Part 1)	-
5.2 (Tensile Strength, Mpa)	-
5.2 (Elongation, %)	-
5.3 (Bend Test-1599)	-
8.2 (Width)	-
8.2 (Thickness)	-
7.1 (Freedom from defects)	-
9.1 (Finishing & Packing)	-

Complete

-
-

196

IS 9890 (1981)

Specification for general purpose ball valves

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (End connections)	-
5 (End connections)	-
11 (Inspection & Test)	-

Complete

-
-

197

IS 4398 (1994)

Carbon - Chromium steel for the manufacture of balls, rollers and bearing races - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 ( Hardness-IS 1500: Pt 1)	-

Partial

-
-

198

IS 10086 (1982)

Specificaton for moulds for use in tests of cement and concrete

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimension and tolerances of cylindrical moulds Table 3)	-
Cl 5.1 (Construction)	-
Cl 5.3 (Arangement for fastening / Clamping)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
5.1.1 (Construction)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
5.1.2 (Construction)	-
5.2.1 (Cube Mould)	-
5.2.2 (Cylindrical Mould (Fig.3))	-
5.2.3 (Beam Mould (Fig. 4))	-
5.2.4 (Bar Mould ( Fig. 5, 6, 7 & 8 ))	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and tolerances of cylindrical moulds Table 3)	-
4.1 (Dimension and tolerances of beam moulds Table 4)	-
4.1 (Dimension and Tolerances of bar moulds Table 5)	-
2.1 (Types)	-
2.1 (Types)	-
2.1 (Types)	-
2.1 (Types)	-
2.1 (Types)	-
4.1 (Dimension and tolerances of cylindrical moulds Table 3)	-

Partial

-
-

199

IS 2052 (2009)

Compounded feeds for cattle - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3 - Table 1 - i (Moisture - Cl 4 of IS 7874 (Part 1))	-
4.3 - Table 1 - ii (Crude protein (N x 6.25) - Cl 5 of IS 7874 (Part 1))	-
4.3 - Table 1 - iii (Crude fat - Cl 7 of IS 7874 (Part 1))	-
4.3 - Table 1 - iv (Crude fibre - Cl 8 of IS 7874 (Part 1))	-
4.3 - Table 1 - v (Acid insoluble ash - Cl 10 of IS 7874 (Part 1))	-
4.3 - Table 2 - i (Salt (as NaCl) - Cl 4 of IS 7874 (Part 2))	-
4.3 - Table 2 - ii (Calcium (as Ca) - IS 13433 (Part 1 / Part 2))	-
4.3 - Table 2 - iii (Total Phosphorus - IS 14828)	-
4.1 (Description - The feed shall be free from harmful constituents, metallic pieces and adulterants. The feed shall also be free from fungal growth and insect infestation. And from fermented . musty, rancid or any other objectionable odour)	-

Partial

-
-

200

IS 15911 (2010)

Structural steel (Ordinary Quality) - Specification

E 165 ,E 170 , E 215

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1, 5.1, 8.1 & 8.2 (Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Nitrogen: Relevant parts of IS 228 or any other established instrumental/chemical method)	-

Partial

-
-

201

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Packing (As per Cl.5.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.1 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.1 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.1 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.1 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.1 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.1 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.1 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.2 (Marking (As per Cl.6.2 of IS 8783 (Part 4/Sec 3) : 1995))	-
4 (Conductor As per IS:8783(Pt 1):1995])	-
5 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
5 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
5 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
5 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
5 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
4.1, table 1 & 2 (Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-
4.1, table 1 & 3 (Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-
4.1, table 1 & 4 (Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-
4.2 (Insulation (As per Cl.4.2 of IS 8783(Part4/Sec 3): 1995)	-
4.3 (Insulation (As per Cl.4.3 of IS 8783(Part4/Sec 3): 1995)	-
4.4 (Insulation (As per Cl.4.4 of IS 8783(Part4/Sec 3): 1995)	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4.1 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4.1 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4.1 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4.1 ([Cl 4.1 and Table-1 of IS:8783(Pt. 2)])	-
4.1 ([Cl 4.1 and Table-1 of IS:8783(Pt. 2)])	-
4.5 ((Cl.4.5 of IS 8783 (Part 4/Sec 3) : 1995))	-
5 (Packing (As per Cl.5.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6 (Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-
6.2 (Marking (As per Cl.6.2 of IS 8783 (Part 4/Sec 3) : 1995))	-
4 (Conductor As per IS:8783(Pt 1):1995])	-
4 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
4 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
4 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
4 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
4 ([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-
4 (Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-
4 (Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-
4 (Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-
4.2 (Insulation (As per Cl.4.2 of IS 8783(Part4/Sec 3): 1995)	-
4 (Insulation (As per Cl.4.3 of IS 8783(Part4/Sec 3): 1995)	-
4 (Insulation (As per Cl.4.4 of IS 8783(Part4/Sec 3): 1995)	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 (Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-
4 ((Cl.4.5 of IS 8783 (Part 4/Sec 3) : 1995))	-
4 ([Cl 4.1 and Table-1 of IS:8783(Pt. 2)])	-
4 ([Cl 4.1 and Table-1 of IS:8783(Pt. 2)])	-

Partial

-
-

202

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
7.1 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
8.1.1 Table 1 (Tensile Strength- IS 1608(1))	-
8.1.1 Table 1 (Yield Strength- IS 1608)	-
8.1.1 Table 1 (Elongation Percent- IS 1608)	-
8.2 (Drift Expansion Test- IS 2335)	-
8.3 (Flattening Test- IS 2328)	-
9.1 Table 2 (Outside Diameter)	-
9.1 Table 2 (Thickness)	-
9.1 Table 2 (Mass)	-
10 (Hardness)	-
13.1.1 (Ovality)	-
13.1.2 (Eccentricity)	-
15.1 (Straightness)	-
16.1 (Length)	-

Partial

-
-

203

IS 2507 (1975)

Specification for cold - rolled steel strips for springs (First Revision)

- View breakup
Rs .6000/- Gr 1 to Gr 9, Rs.3900/- for Gr.10, Rs.4500/- for Gr.11

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Carbon- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Sulphur- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Silicon- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Manganese- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Phosphorus- Appropriate parts of IS 228.)	-
7 (Rolling Tolerances)	-
10 (Physical properties(optional))	-
5 (FREEDOM FROM DEFECTS)	-

Partial

-
-

204

IS 8931 (1993)

copper alloy fancy single taps, combination tap assembly and stop valves for water services

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.6 (Screw Threads)	-
Cl 6.7 (Waterway)	-
Cl 6.9 (Body Seat)	-
Cl 7.3 (Bonnet Assembly)	-
Cl 8 (Finish)	-

Partial

-
-

205

IS 2029 (1998)

Ring wrenches (Spanners) - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3, Table-1 (Dimensions- s1)	-
3, Table-1 (Dimensions- s2)	-
3, Table-1 (Dimensions- a)	-
3, Table-1 (Dimensions- b1)	-
3, Table-1 (Dimensions- b2)	-
3, Table-1 (Dimensions- L)	-
6 (Workmanship and Finish)	-
7 (Designation)	-

Partial

-
-

206

IS 2721 (2003)

Galvanized steel chain link fence fabric - Specification (Second Revision)

- View breakup
Rs.5950/- (for wire below 5 mm Dia), Rs.6910/- (for wires above 5 mm Dia) and Material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.8 (Chain link fence fabric(Mass of zinc coating)- IS 6745)	-
Cl.8 (Chain link fence fabric (Uniformity of Zinc coating)-IS 2633)	-
Cl.9.2 (Mesh wire (Mass of zinc coating)- IS 6745)	-
Cl.9.2 (Mesh Wire (Uniformity of Zinc coating)-IS 2633)	-
Cl.6.1, 6.2, Table 1 (Mesh Size)	-
Cl.6.3, Table 1 (Width of the fabric)	-
Cl.6.3, Table 1 (Length of the fabric)	-
Cl.6.1, 6.2, Table 1 (Nominal Dia of Mesh wire)	-
Cl. 7.2 and Table 1 (Line Wire (Diameter))	-
Cl. 7.2 and Table 1 (Line Wire (Number of wires))	-
Cl.9.1.1 (Tensile test of mesh and line wires- IS 1608)	-
Cl.9.1.2 (Wrapping test of mesh and line wires-IS 1755)	-
Cl.9.1.3 (Twist test of mesh and line wires-IS 1717)	-
Cl.9.1.4 (Bend test of mesh and line wires- IS 1608)	-

Partial

-
-

207

IS 7098 : Part 3 (1993)

Cross - Linked polyethylene insulated thermoplastic sheathed cables - Specification: Part 3 for working voltages from 66 kV up to and including 220 kV

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

208

IS 4223 (1975)

Steel Wire For Umbrella Ribs

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8,9 (Sizes and Tolerances - IS 4223)	-
10.1, Table 1 (Mechanical ptoperties - IS 1608(Pt -1))	-
10.2 (Torsion Test - IS 1717)	-
7 (Freedom rom defects , IS 4223)	-
10.3 (Reverse Bend Test--IS 1716)	-

Complete

-
-

209

IS 2028 (2004)

Open jaw wrenches (Spanners) - Specification (Fijih Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Dimensions- a)	-
3.1 (Dimensions- b)	-
3.1 (Dimensions- l)	-
3.2, 3.3, 3.4 (Dimensions- a)	-
3.2, 3.3, 3.4 (Dimensions- b1)	-
3.2, 3.3, 3.4 (Dimensions- b2)	-
3.2, 3.3, 3.4 (Dimensions- l)	-
3.2, 3.3, 3.4 (Dimensions- b2)	-
6 (Workmanship And Finish)	-

Partial

-
-

210

IS 9523 (2000)

Ductile iron fittings for pressure pipes for water, gas and sewage - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Thickness)	-
Cl 6 & Table 4,5,6&7 (Design & Tolerance)	-
Cl 9 (Tensile Test & Hardness Test)	-
Cl 10 (Hydrostatic Test)	-
Cl 11 (Nominal Diameter, Ovality, Dimensions, No. Of Holes & Bolt Sizes)	-
Cl 13 (Coating)	-

Complete

-
-

First
Prev
6
7
8
9
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Office Laboratory (NROL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- [email protected]

Scope List

No Record Found