BIS - LIMS (Laboratory Information Management System)

IDMA LABORATORIES LIMITED

PLOT NO 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 [email protected]

Scope List

Reset

154 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.4(Chloride content)	-	1000	NA
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	3000	NA
Cl 3.2(Initial & Final)	-	1000	NA
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	3000	NA

Complete

31 Dec, 2023

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	500	NA
Cl 9.3(Load In One Direction)	-	200	NA
Cl 8.1(UTM)	-	200	NA
Cl 7.2(Weight)	-	200	NA
Cl 6.1(Length, Width & Thickness)	-	200	Clause 4.2 Carbon content RS/- 200, Mn Rs/- 200, Si, S,P,Cr,Mo, Cu, Ni, V, N, Al, Nb, Ti (RS/- 250 each), Clause 8.1 (i, ii) 0.2 % proof stress/ yield stress RS/-400 each, 8.1 (iii) TS/YS Ratio N/mm2 RS/-200, 8.1 (iv) Elongation RS/-400
Cl 5(Deformations and Surface Characteristics)	-	400	8.1 (v) Total elongation at maximum force RS/-400, Clause 8.2/9.3 Bend RS/-200 Note: Reporting charges RS/-200
Cl. 8.1 Table 3(Tensile Strength (TS))	-	-	-
Cl. 8.1 Table 3(Elongation, percentage)	-	-	-
Cl. 8.1 Table 3(TS/YS ratio)	-	-	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	-	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	-	-
Cl. 6.1(Nominal Size)	-	-	-
Cl. 7.2 Table -2 (Nominal Mass)	-	-	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	-	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	-	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	-	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	-	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	-	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	-	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	-	-
Cl 5(Deformations and Surface Characteristics)	-	-	-
Cl 5(Deformations and Surface Characteristics)	-	-	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	-	-
8.18.1 Table 3(Total elongation at maximum force)	-	-	-
Cl. 9.3, Table 4(Bend Test )	-	-	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	-	-
Clause 9.4(Rebend Test)	-	-	-
Clause 6.3(Effective Cross-sectional Area)	-	-	-
Clause 8.1(Table 3)(Total Elongation at Maximum Force)	-	-	-

Complete

31 Dec, 2023

-
-

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Diameter)	-	250	NA
Cl 6.1(Tensile Test On UTM)	-	700	NA
Cl 6.2(Tensile Test On UTM)	-	550	NA
Cl 6.3(Tensile Test On UTM)	-	650	Note: Reporting charges RS/-200 Clause no 3.1.1 S, P RS/- 200 each, Clause no 3.3, 3.4 freedom from surface defects RS/-200, Clause 7.5 Reverse bend test RS/- 550
Cl 5.1.2(Weight)	-	-	-
3.1.1(PHOSPHORUS)	-	-	-
3.1.1(SULPHUR)	-	-	-
Clause 3.3(Workmanship )	-	-	-
Clause 3.4(Surface Finish)	-	-	-
Clause 3.5(Weld joints)	-	-	-
Clause 6.4(Uncoiling Of Wire)	-	-	-

Complete

31 Dec, 2023

-
-

IS 1785 : Part 1 (1983)

Specification for plain hard - Drawn steel wire for prestressed concrete: Part 1 cold drawn stress - Relieved wire (Second Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6.1(Tensile Test On UTM)	-	1000	NA
Cl 6.2(Tensile Test On UTM)	-	600	NA
Cl 6.4(Tensile Test On UTM)	-	300	NA
Cl 6.5(Load )	-	30000	NA
Cl 5.1(Diameter)	-	300	NA
Cl 6.3(Reverse Bend Test)	-	500	Note: Reporting charges RS/-200 Clause 3.1.1 Sulphur, Phosphorous (RS/- 350,350), Clause 3.4 Finish RS/- 200, Clause 3.3 Workmanship RS/-200, Clause 3.5 Finish of Weld RS/-200, Clause 6.3 Ductility RS/- 800
Cl 6.5(Load )	-	-	-
Cl 6.4(Tensile Test On UTM)	-	-	-
Cl 6.5(Load )	-	-	-
Clause 3.3(Workmanship )	-	-	-
Clause 3.4(Surface Finish)	-	-	-
Clause 3.5(Weld joints)	-	-	-
Clause 6.5(Relaxation stress(1000 h))	-	-	-
Clause 6.5.1(Relaxation stress(100 h))	-	-	-
Clause 3.1.1(Sulphur)	-	-	-
Clause 3.1.1(Phosphorus)	-	-	-

Complete

31 Dec, 2023

-
-

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

2850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Tables 2 to 9 (2)(Size of Hinge)	-	40	NA
5.1 Tables 2 to 9 (3)(Length A)	-	40	NA
5.1 Tables 2 to 9 (4)(Breadth B)	-	40	NA
5.1 Tables 2 to 9 (4)(Breadth B1)	-	40	NA
5.1 Tables 2 to 9 (4)(Breadth B2)	-	40	NA
5.1 Tables 2 to 9 (5)(Thickness of Flap C)	-	40	NA
5.1 Tables 2 to 9 (6)(Diameter of Hinge Pin D)	-	40	NA
5.1 Tables 2 to 9 (7)(Number of Knuckles)	-	40	NA
5.1 Tables 2 to 9 (8)(Number of Screw Holes)	-	40	NA
5.1 Tables 2 to 9 (9)(Holes for Screw No.)	-	40	NA
6.1(General)	-	350	NA
6.2.1(Knuckles)	-	250	NA
6.3(Pins)	-	350	NA
6.4(Screw Holes)	-	350	NA
6.4.2(Position of Holes)	-	350	NA
7(Finish)	-	350	Note : Reporting charges RS/-200
6.4.2(X)	-	-	-
6.4.2(Y)	-	-	-
6.4.2(Z)	-	-	-
6.4.2.1(Position of Holes)	-	-	-
Clause 4 Table 1(Carbon ( Flap))	-	-	-
Clause 4 Table 1(Sulphur ( Flap))	-	-	-
Clause 4 Table 1(Phosphorus ( Flap))	-	-	-
Clause 4 Table 1(Manganese ( Flap))	-	-	-
Clause 4 Table 1(Nitrogen ( Flap))	-	-	-
Clause 4 Table 1(Carbon ( Pin))	-	-	-
Clause 4 Table 1(Sulphur ( Pin))	-	-	-
Clause 4 Table 1(Phosphorus ( Pin))	-	-	-
Clause 4 Table 1(Manganese ( Pin))	-	-	-

Complete

31 Dec, 2023

-
-

IS 1239 : Part 2 (2011)

Steel tubes, tubulars and other steel fittings - Specification: Part 2 steel pipe fittings (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14(WORKMANSHIP)	-	-	-
8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces )	-	-	-
8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces-Approximate Standard Length(A) )	-	-	-
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-A )	-	-	-
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-B )	-	-	-
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-C )	-	-	-
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-A)	-	-	-
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-B)	-	-	-
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-C)	-	-	-
8.3.2(DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-	-	-
8.4.1 -Table 4(Bends and springs)	-	-	-
8.4.1 -Table 4(Bends and springs-A)	-	-	-
8.4.1 -Table 4(Bends and springs-B)	-	-	-
8.4.1 -Table 4(Bends and springs-R)	-	-	-
8.4.1 -Table 4(Bends and springs-C)	-	-	-
8.4.1 -Table 4(Bends and springs-D)	-	-	-
8.4.1 -Table 4(Bends and springs-E)	-	-	-
8.5-Table 5( Return Bends-A)	-	-	-
8.5-Table 5( Return Bends-B)	-	-	-
8.5-Table 5( Return Bends)	-	-	-
8.6 -Table 6(Sockets-A)	-	-	-
8.6 -Table 6(Sockets-B)	-	-	-
8.6 -Table 6(Maximum Inside Diameter of Internal Parallel Thread)	-	-	-
9.1-Table 7(Dimensions of Screwed Ends of Fittings-D )	-	-	-
9.1-Table 7(Dimensions of Screwed Ends of Fittings-E )	-	-	-
9.1-Table 7(Dimensions of Screwed Ends of Fittings-d )	-	-	-
9.1-Table 7(Dimensions of Screwed Ends of Fittings-Taper )	-	-	-
9.1-Table 8 (Dimensions of Elbows, Tees and Crosses, Equal-A)	-	-	-
9.1-Table 9 (Dimensions of Elbows Reducing-A)	-	-	-
9.1-Table 9 (Dimensions of Elbows Reducing-B)	-	-	-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-A)	-	-	-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-B)	-	-	-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-A)	-	-	-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-B)	-	-	-
9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-A)	-	-	-
9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-B)	-	-	-
9.1-Table 13( Dimensions of Crosses, Reducing-A)	-	-	-
9.1-Table 13( Dimensions of Crosses, Reducing-B)	-	-	-
9.1-Table 14( Elbows, Tees and Crosses, Side Outlet, Equal-A)	-	-	-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-A)	-	-	-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-B)	-	-	-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Minimum Bore of Male End)	-	-	-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Maximum Bore of Male End)	-	-	-
9.1-Table 16( Dimensions of Elbows, Equal, 135°-A)	-	-	-
9.1-Table 17 (Dimensions of Y-Pieces, Female, Equal-A)	-	-	-
9.1-Table 18 (Dimensions of Socket, Reducing-A)	-	-	-
9.1-Table 19 (Dimensions of Caps-A)	-	-	-
9.1-Table 19 (Dimensions of Caps-T)	-	-	-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge)	-	-	-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-S)	-	-	-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-H)	-	-	-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-D)	-	-	-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-K)	-	-	-
9.1-Table 21 (Dimensions of Elbows, Tees and Crosses, Male, Equal-A)	-	-	-
9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-A )	-	-	-
9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-B )	-	-	-
9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-A)	-	-	-
9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-B)	-	-	-
9.1-Table 24(Dimensions of Socket Unions-A )	-	-	-
9.1-Table 25 (Dimensions of Pipe Unions-A)	-	-	-
9.1-Table 26 (Dimensions of Union Bends-A )	-	-	-
9.1-Table 26 (Dimensions of Union Bends-B )	-	-	-
9.1-Table 27 (Dimensions of Hexagon Bushes-L)	-	-	-
9.1-Table 27 (Dimensions of Hexagon Bushes-T)	-	-	-
9.1-Table 27 (Dimensions of Hexagon Bushes-A)	-	-	-
9.1-Table 27 (Dimensions of Hexagon Bushes-B)	-	-	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-L)	-	-	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-T)	-	-	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-A)	-	-	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-C)	-	-	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-B)	-	-	-
11.1(a)(Internal hydraulic Pressure Test)	-	-	-
11.2.1( Drift Expanding Test)	-	-	-
11.2.2 (Taper Screw Plug Test)	-	-	-
13 and as per IS 4736(UNIFORMITY OF ZINC COATING)	-	-	-
13 and as per IS 4736(MASS OF ZINC COATING)	-	-	-
7.1(Chemical Composition - Sulphur - Laddle Analysis IS 228)	-	-	-
7.1(Chemical Composition - Phosphorus - Laddle Analysis IS 228)	-	-	-
Clause 9.1, Table- 27(Normal Size (Internal Threads) (Dimensions of Hexagon Bushes) )	-	-	-
Clause 9.1, Table- 27(Normal Size (External Threads) (Dimensions of Hexagon Bushes) )	-	-	-
Clause 9.2.2 (Tolerance for alignment of threads )	-	-	-
Clause 9.2.3 (Threads tolerance )	-	-	-
Clause 10(Joints )	-	-	-
Clause 13.1.3 (Adhesion Test)	-	-	-
Clause 8.3.3(Parallel threads )	-	-	-

Complete

31 Dec, 2023

-
-

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Outer Diameter, Thickness & Mass)	-	-	-
Cl 8(Outer Diameter, Thickness & Mass)	-	-	-
Cl 8(Outer Diameter, Thickness & Mass)	-	-	-
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	-	-
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	-	-
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	-	-
Cl 15(Workmanship)	-	-	-

Complete

31 Dec, 2023

-
-

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

5100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Outer Diameter, Thickness & Mass)	-	400	Clause no 5 Material (Chemical test as IS 10748) C,S,P, Mn, Si, Cr, Mo, V, Ni, Cu, Bend test, Freedom from defects (RS/-100,100,100.100,200,200,200,250,250,200,150,100 respectively)
Cl 7(Workmanship)	-	100	Clause no 6 Nominal bore RS/-100, Area of cross section RS/-150, Internal volume RS/-100, Surface RS/-200, Moment of inertia RS/-100, Modulus of section RS/-100, Radius of Gyration RS/- 100,Square of Radius of Gyration RS/- 100
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	800	Clause 8 Zinc coating RS/-200 Clause 9 Straightness RS/-150 Clause 10 Length RS/-50 Clause 11 Yield stress RS/- 150, Elongation RS/- 150 Reporting charges RS/-200
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	-	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	-	-
Cl 6(Outer Diameter, Thickness & Mass)	-	-	-
Cl 6(Outer Diameter, Thickness & Mass)	-	-	-
10(Lengths)	-	-	-
9(Straightness)	-	-	-
Cl. 11.2 Table 2(Yield strength)	-	-	-
Cl. 11.2 Table 2(Elongation)	-	-	-

Complete

31 Dec, 2023

-
-

IS 15939 (2011)

Pesticide - Bifenthrin wettable powder - Specification

5800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	150	NA
3.3.Table 1.i(Bifenthrin content)	-	1900	NA
3.3.Table 1.ii(Sieve test)	-	550	NA
3.3.Table 1.iii(Wettability)	-	900	NA
3.3.Table 1.v(Alkalinity)	-	1000	NA
3.3.Table 1.vi(Suspensibility)	-	900	NA
3.3.Table 1.iv(pH of 5 percent suspension)	-	200	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

100

IS 15603 (2005)

Alphacypermethrin, WP - Specification

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	200	NA
3.2.2(Sieving Requirements)	-	700	NA
3.2.3(Suspensibility Test)	-	1500	NA
3.2.4(Wettability)	-	900	NA
3.3.1(Alphacypermethrin content)	-	1500	NA
3.3.2(Acidity or Alkalinity)	-	500	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

101

IS 15443 (2004)

Imidacloprid technical - Specification

3300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	200	NA
3.2.i(lmidacloprid Content)	-	1800	NA
3.2.ii(Moisture Content)	-	600	NA
3.2.iii(Acidity/Alkalinity)	-	500	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

102

IS 15335 (2003)

Imidacloprid SL - Specification

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	200	NA
3.2.2(Cold Test)	-	500	NA
3.2.3(Flash Point (Abel))	-	600	NA
3.3.1(lmidacloprid Content)	-	1400	NA
3.3.2(Acidity)	-	300	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

103

IS 15160 (2002)

Pretilachlor emulsifiable concentrate - specification

3600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	150	NA
3.2.2(Cold Test)	-	350	NA
3.2.3(Flash Point (Abel))	-	350	NA
3.2.4(Emulsion Stability)	-	700	NA
3.3.1(Pretilachlor content)	-	1150	NA
3.3.2(Acidity)	-	700	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

104

IS 14807 (2000)

Phosphate solubilising bacterial inoculant (PSBI) - Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CL 4.1(Phosphate Solubilising Bacterial cells)	-	4000	NA
CL 4.2(Color)	-	600	NA
CL 4.3(Dilution)	-	1800	NA
CL 4.4(pH)	-	400	NA
CL 4.5(Phosphate solubilising)	-	3000	NA Note: Reporting charges RS/-200

Complete

31 Dec, 2023

-
-

105

IS 14806 (2000)

Azospirillum inoculants

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CL 4(DETERMINATION OF NUMBER OF AZOSPIRILLUM CELLS)	-	4000	NA
CL 4.2(Powder carrier material)	-	600	NA
CL 4.3(DETERMINATION OF NUMBER OF AZOSPIRILLUM CELLS)	-	1800	NA
CL 4.4(pH)	-	400	NA
CL 4.5(TEST FOR EFFECTIVE ROOT GROWTH)	-	200	NA Note: Moisture RS/-2800 Reporting charges RS/-200

Complete

31 Dec, 2023

-
-

106

IS 14510 (1997)

Lambda - Cyhalothrin WP - Specification

3980 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	180	NA
3.3 Table 1 i(Lamda cyhalothrin content )	-	1800	NA
3.3 Table 1 ii(Sieving requirements material passing through 75 micron IS sieve)	-	500	NA
3.3 Table 1 iii(Suspensibility)	-	500	NA
3.3 Table 1 iv(Wettability)	-	400	NA
3.3 Table 1 v(Acidity/Alkalinity)	-	400	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

107

IS 14411 (1996)

Deltamethrin F - Specification

3300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	200	NA
3.3(Deltamethrin Content)	-	1800	NA
3.4(Dispersibility in -Water)	-	600	NA
3.5(Acidity)	-	500	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

108

IS 14300 (1995)

Neem based EC containing azadirachtin - Specification

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.2.1(Description)	-	250	NA
Cl. 3.2.2(Cold Test)	-	650	NA
Cl. 3.2.3(Flash point)	-	650	NA
Cl. 3.2.4(Emulsion Stability)	-	650	NA
Cl. 3.3.1(Azadirectin content)	-	1250	NA
Cl. 3.3.3(Aflatoxin content)	-	750	-
3.3.2(Acidity/ Alkalinity)	-	300	-

Complete

31 Dec, 2023

-
-

109

IS 14184 (1994)

Pesticide - Cartap hydrochloride G - Specification

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	200	NA
3.2.2(Particle Size)	-	500	NA
3.2.3(Dust)	-	500	NA
3.2.4(Moisture Content)	-	500	NA
3.3.1(Cartap Hydrochloride Content )	-	1200	NA
3.3.2(pH or 1 percent ( mlm ) extract)	-	400	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

110

IS 14183 (1994)

Pesticide - Cartap hydrochloride SP - Specification

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	200	NA
3.3 Table 1 i(Cartap Hydrochloride Content)	-	1600	NA
3.3 Table 1 ii(Matter insoluble in water )	-	500	NA
3.3 Table 1 iii(pH or 10 percent ( mlm ) extract)	-	500	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

111

IS 13457 (1992)

Pesticide - Deltamethrin WP specification

4300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	200	NA
Cl. 3.3 Table 1(Sieving (material passing through 45 Micron IS Sieve),)	-	600	NA
Cl. 3.3 Table 1(Suspensibility, )	-	600	NA
Cl. 3.3 Table 1(Wettability )	-	600	NA
Cl. 3.3&3.3.1 Table 1(Deltamethrin content, )	-	1500	NA
Cl. 3.3 Table 1(Acidity (as H2SO4), or Alkalinity (as NaOH))	-	600	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

112

IS 12931 (1990)

Atrazine WP - Specification

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	100	NA
3.3 Table 1 i(Atrazine Content)	-	1000	NA
3.3 Table 1 ii(Sieving requirements material passing through 75 micron IS sieve)	-	600	NA
3.3 Table 1 iii(Suspensibility)	-	600	NA
3.3 Table 1 v(Wettability)	-	500	NA
3.3 Table 1 iv(Acidity/Alkalinity)	-	500	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

113

IS 12751 (1989)

Pesticides - Pendimethalin EC - Specification

5400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	550	NA
3.2.2(Cold Test)	-	750	NA
3.2.3(Flash Point (Abel))	-	750	NA
3.2.4(Emulsion Stability)	-	850	NA
3.3.1(Pendimethalin content)	-	1500	NA
3.4(Acidity/Alkalinity)	-	800	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

114

IS 12016 (1987)

Specification for cypermethrin EC

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.1(Description)	-	200	NA
2.2.2(Cold Test)	-	600	NA
2.2.3(Flash Point (Abel))	-	500	NA
2.2.4(Emulsion Stability)	-	500	NA
2.3.1(Cypermethrin content)	-	1100	NA
2.3.2(Acidity)	-	400	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

115

IS 11997 (1987)

Specification for fbnvaleratb AC

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.1(Description)	-	200	NA
2.2.2(Cold Test)	-	800	NA
2.2.3(Flash Point (Abel))	-	800	NA
2.2.4(Emulsion Stability)	-	800	NA
2.3.1(Fenvelarte content)	-	1600	NA
2.3.2(Acidity/Alkalinity)	-	600	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

116

IS 10243 (1993)

2,4 - D ethyl ester EC- Specificationn (First Revision)

3920 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	120	NA
3.4.1(Cold Test)	-	400	NA
3.4.2(Flash Point (Abel))	-	400	NA
3.4.3(Emulsion Stability)	-	800	NA
3.5.1(2,4-D Ethyl Ester EC content)	-	1000	NA
3.5.2(Fee 2,4-D)	-	1000	-
3.3(Identity Test)	-	200	-

Complete

31 Dec, 2023

-
-

117

IS 8944 (2005)

Chlorpyrifos, emulsifiable concentrates - Specification (First Revision)

3300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	200	NA
3.2.2(Cold Test)	-	400	NA
3.2.3(Flash Point (Abel))	-	400	NA
3.2.4(Emulsion Stability)	-	550	NA
3.3.1(Chloropyrifos content)	-	1150	NA
3.3.2(Acidity (as H2SO4), )	-	400	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

118

IS 8708 (2006)

Mancozeb wettable powder - Specification (First Revision)

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	100	NA
3.2.2(Sieving Requirement)	-	400	NA
3.2.3(Suspensibility)	-	1600	NA
3.2.4(Wettability)	-	500	NA
3.3.1(Mancozeb Content)	-	1500	NA
3.3.2(Zinc Content)	-	600	NA
3.3.3(Manganese Content)	-	600	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

119

IS 8249 (2019)

Zinc sulphate heptahydrate, agricultural grade - Specification (First Revision)

6300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Clauses 3.2 and 6.2) Table 1(Matter insoluble in water)	-	500	NA
(Clauses 3.2 and 6.2) Table 1(Zinc (as Zn))	-	850	NA
(Clauses 3.2 and 6.2) Table 1(Lead (as Pb))	-	750	NA
(Clauses 3.2 and 6.2) Table 1(Copper (as Cu))	-	800	NA
(Clauses 3.2 and 6.2) Table 1(Magnesium (as Mg))	-	800	NA
(Clauses 3.2 and 6.2) Table 1(pH)	-	400	NA
(Clauses 3.2 and 6.2) Table 1(Sulphur (as S))	-	800	NA
(Clauses 3.2 and 6.2) Table 1(Cadmium (as Cd))	-	700	NA
(Clauses 3.2 and 6.2) Table 1(Arsenic (as As))	-	700	NA
3.1(Description)	-	-	-

Complete

31 Dec, 2023

-
-

120

IS 2569 (1978)

Specification for malathion water dispersible powder concentrates

5000 View breakup
Rs.5000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Description)	-	200	NA
2.2. Table1.i(Malathion Content)	-	1500	NA
2.2. Table1.ii(Sieving requirement)	-	950	NA
2.2. Table1.iii(Suspensibility)	-	1550	NA
2.2. Table1.iv(Acidity)	-	600	Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

First
Prev
3
4
5
6
Next
Last

Bureau of Indian Standards

The National Standards Body of India

IDMA LABORATORIES LIMITED

PLOT NO 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 [email protected]

Scope List