BIS - LIMS (Laboratory Information Management System)

IDMA LABORATORIES LIMITED

PLOT NO 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 [email protected]

Scope List

Reset

154 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 2791 (1992)

Soluble coffee powder - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4 Table 1(Caffeine content)	-	-	-
3.1(Description )	-	-	-
3.4 Table 1(Moisture content)	-	-	-
3.4 Table 1(Total ash)	-	-	-
3.4 Table 1(Caffeine content)	-	-	-
3.4 Table 1(Solubility in boiling)	-	-	-
3.4 Table 1(Solubility in cold water)	-	-	-

Complete

31 Dec, 2023

-
-

IS 3309 (1992)

Soluble Coffee - Chicory powder - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4 Table 1(Caffeine content)	-	-	-
3.7(Copper content)	-	-	-
3.6.2.4(Monocrotophos)	-	-	-
3.1(Description)	-	-	-
3.4 Table 1(Moisture content)	-	-	-
3.4 Table 1(Total ash)	-	-	-
3.4 Table 1(Solubility in boiling)	-	-	-
3.4 Table 1(Solubility in cold water)	-	-	-

Complete

31 Dec, 2023

-
-

IS 9359 (1995)

Pesticide - Phorate G encapsulated - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Physical -Description)	-	-	-
3.2.2(Physical - Sieving Requiremenr)	-	-	-
3.2.3(Dust)	-	-	-
3.2.4.1(Encapsulation- % of declared nominal active ingredient in remnants.)	-	-	-
3.2.5(Moisture Content)	-	-	-
3.3.1(Phorate Content)	-	-	-
3.3.2(Acidity)	-	-	-

Complete

31 Dec, 2023

-
-

IS 14309 (1995)

Blended edible vegetable oils specification

- View breakup
Rs..5500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

31 Dec, 2023

-
-

IS 14509 (1997)

Lambda - Cyhalothrin, technical - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

31 Dec, 2023

-
-

IS 14551 (1998)

Thiophanate methyl, technical - Specificaiton

3600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	200	-
Table 1 (i), cl.3.2(Thiophanate methyl content)	-	1500	-
Table 1 (ii), cl.3.2(Moisture content)	-	700	-
Table 1 (iii), cl.3.2(Acidity)	-	500	-
Table 1 (iv), cl.3.2(Material insoluble in acetone)	-	700	-

Complete

31 Dec, 2023

-
-

IS 14552 (1998)

Thiophanatemethyl, WP specification

5200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	200	NA
3.3 Table 1 i(Thiophanate methyl content )	-	1600	NA
3.3 Table 1 ii(Material passing through 75 micron IS sieve)	-	800	NA
3.3 Table 1 iii(Suspensibility)	-	1200	NA
3.3 Table 1 iv(Acidity/Alkalinity)	-	600	NA
3.3 Table 1 v(Wettability)	-	600	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Workmanship)	-	200	NA
Cl 5 & 6(Diameter)	-	400	NA
Cl 7(UTM)	-	1900	NA
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	900	Note: Clause 3.1 Nitrogen RS/-1200, Sulphur RS/-350, Phosphorous RS/-350 Reporting charges RS/-200
Cl 7(UTM)	-	-	-
Cl 7(UTM)	-	-	-
Clause 3.1.1(Sulphur)	-	-	-
Clause 3.1.1(Phosphorus)	-	-	-
Clause 3(Nitrogen)	-	-	-
Clause 7.1(Ultimate Tensile Stress)	-	-	-
Clause 7.1(Proof Stress (0.2 percent ))	-	-	-
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	-	-

Complete

31 Dec, 2023

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

3100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	50	NA
Cl 6.2(Diameter & Ovality)	-	50	NA
Cl 8.2(Bend test)	-	600	NA
Cl 6.2(Weight)	-	50	NA
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	0	NA
Cl 9.3(Press)	-	250	Note : Reporting charges RS/- 200 Clause 4- C,S,P,Mn, Si, Cr, Mo, V RS/-200 each , Ni, Cu RS-150 each
Cl 8(Physical Requirements)	-	-	-
Clause -4, 4.1(SULPHUR)	-	-	-
Clause -4, 4.1(PHOSPHURS)	-	-	-
Clause -4, 4.1(SILICON)	-	-	-
Clause -4, 4.1(MANGANESE)	-	-	-
Clause -4, 4.1( CARBON)	-	-	-
Clause -4, 4.1(NITROGEN)	-	-	-
Clause 6.1(Size)	-	-	-
Clause 9.3(Bend test)	-	-	-
Clause 8.1(Yield Stress)	-	-	-
Clause 8.1(Elongation)	-	-	-

Complete

31 Dec, 2023

-
-

IS 15138 (2010)

Textiles – Jute bags for packing 50 kg sugar – Specification (first revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.1,5.2 Table 1,i) a) Cl.8.3.2 of IS 9113 Table A / B / C( Outside length )	-	400	NA
5,5.1,5.2 Table 1,i) b) Cl.8.3.2 of IS 9113 Table A / B / C(Outside width)	-	400	NA
5,5.1,5.2 Table 1,ii) Cl.8.4.2 of IS 9113 Table A / B / C(Ends/dm)	-	250	NA
5,5.1,5.2 Table 1,iii) Cl.8.4.2 of IS 9113 Table A / B / C(Picks/dm)	-	250	NA
5,5.1,5.2 Table 1,iv) Cl.8.5.2 of IS 9113 Table A / B / C(Corrected mass per bag)	-	500	NA
5,5.1,5.2 Table 1,v) a) Cl.8.6.2 of IS 9113 Table A / B / C(Average breaking load of sacking (ravelled strip method, 5.0 cm × 20.0 cm), Min, N (kgf) Warpway:)	-	500	NA
5,5.1,5.2 Table 1,v) b) Cl.8.6.2 of IS 9113 Table A / B / C(Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Weftway :)	-	500	NA
5,5.1,5.2 Table 1,vi) a) Cl.8.7 of IS 9113 Table A / B / C( Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Warpway:)	-	500	NA
5,5.1,5.2 Table 1,vi) b) Cl.8.7 of IS 9113 Table A / B / C( Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Weftway :)	-	500	NA
5,5.1,5.2 Table 1,vii)a) Cl.8.2 of IS 9113 Table A / B / C(Moisture regain)	-	450	NA
5,5.1,5.2 Table 1,vii)b) Table A / B / C(Contract moisture regain)	-	450	NA
4.2 IS 9113(Seam )	-	300	NA
4.3 IS 9113(Hemming at the Mouth )	-	300	NA
4.4 Annex B(Freedom from Defects)	-	500	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

6150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 and Table 1 ii a(Dimensions Inside Length)	-	200	NA
5.2 and Table 1 ii b(Dimensions Inside Width)	-	200	NA
5.2 and Table 1 iii(Ends per dm )	-	150	NA
5.2 and Table 1 iv(Picks per dm )	-	150	NA
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	200	NA
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	200	NA
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	500	NA
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	500	NA
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	300	NA
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	NA
5.2 and Table 1 x(Ash content )	-	500	NA
4.3(Sacks)	-	100	NA
4.3.1(The two rows of stitches shall be separated from each other)	-	250	NA
4.3.1( The outer stitch)	-	250	NA
4.4(Liner IS 10146 or IS 10910.)	-	250	Note: Reporting Charges RS-200/-
4.3(Sacks)	-	100	-
4.3.1(Bottom Seam)	-	100	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	100	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	100	-
4.3.1(stitches/dm)	-	100	-
4.3.2(Mouth)	-	100	-
4.4(Mass of the loose liner )	-	100	-
4.4(Width of the loose liner)	-	100	-
4.4(Length of the line)	-	100	-
4.4(Bottom seam of the loose liner)	-	100	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	150	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	500	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	300	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1050	-
5.2 and Table 1 x(Ash content )	-	800	-

Complete

31 Dec, 2023

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

6200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.3.1(Bottom seam (IS 10789))	-	100	NA
4.2 and Table 1 ii(Dimensions )	-	200	NA
5.2 and Table 1 iii(Ends per dm )	-	300	NA
5.2 and Table 1 iv(Picks per dm )	-	300	NA
4.2 and Table 1 v(Mass of sack )	-	800	NA
4.2 and Table 1 vi(Average breaking strength of fabric )	-	800	NA
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	800	NA
4.2 and Table 1 viii(Elongation at break of fabric )	-	800	NA
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1500	NA
4.2 and Table 1 x(Ash content )	-	400	Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

IS 15658 (2006)

Precast concrete blocks for paving - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.1 & 7.1(VISUAL INSPECTION)	-	700	NA
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	0	NA
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	0	NA
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	0	NA
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	0	NA
B-1.3.1(MEAN INDIVIDUAL LENGTH (of all eight test specimens), L)	-	0	NA
B-5(AVERAGE LENGTH (Average for eight test specimens), L)	-	0	NA
Table 1(MINIMUM PAVER BLOCK THICKNESS)	-	0	NA
B-1.3.2(MEAN INDIVIDUAL THICKNESS (of all eight test specimens), T)	-	0	NA
B-5(AVERAGE THICKNESS (Average for eight test specimens), T)	-	0	NA
B-1.3.3(INDIVIDUAL ASPECT RATIO (L/T) (of all eight test specimens))	-	0	NA
B-5(AVERAGE ASPECT RATIO (L/T) (for eight test specimens))	-	0	NA
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	0	NA
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	0	NA
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	0	NA
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	0	NA
B-5(INDIVIDUAL PLAN AREA, ASP (of all eight test specimens) )	-	0	NA
B-5(AVERAGE PLAN AREA, ASP (for eight test specimens))	-	0	NA
B-5(INDIVIDUAL WEARING FACE AREA, Asw (of all eight test specimens))	-	0	NA
B-5(AVERAGE WEARING FACE AREA, Asw (for eight test specimens))	-	0	NA
B- 4.3(MEAN INDIVIDUAL SQUARENESS (of all eight test specimens) )	-	0	NA
B-5(AVERAGE SQUARENESS (for eight test specimens))	-	0	NA
6.2.3(THICKNESS OF WEARING LAYER, if the sample is Double Layered (for eight test specimens))	-	0	NA
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	2600	NA
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	0	NA
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens) )	-	0	NA
6.2.5.1(INDIVIDUAL COMPRESSIVE STRENGTH (Individual strength of eight test specimen))	-	0	NA
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	0	NA
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	0	NA
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	0	NA
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	0	NA
6.2.7(INDIVIDUAL TENSILE SPLITTING STRENGTH (Individual strength of eight test specimen ))	-	0	NA
6.2.7(AVERAGE TENSILE SPLITTING STRENGTH (for eight test specimen ))	-	0	NA
6.2.8(INDIVIDUAL FLEXURAL STRENGTH (Individual strength of eight test specimen ))	-	0	NA
6.2.8(AVERAGE FLEXURAL STRENGTH (Average strength of eight test specimen ))	-	0	-
6.1.2(Physical requirement)	-	0	NA
6.1.3(Physical requirement)	-	0	NA
6.1.4(Physical requirement)	-	100	NA
6.2.2, Table 4(Length)	-	370	-
6.2.2, Table 4(Length)	-	0	-
6.2.2, Table 4(Length)	-	0	-
6.2.2, Table 4(Length)	-	0	-
6.2.2, Table 4(Length)	-	0	-
6.2.2, Table 4(Length)	-	0	-
6.2.2, Table 4(Length)	-	0	-
6.2.2, Table 4(Length)	-	0	-
6.2.2, Table 4(Higher Width)	-	366	-
6.2.2, Table 4(Higher Width)	-	0	-
6.2.2, Table 4(Higher Width)	-	0	-
6.2.2, Table 4(Higher Width)	-	0	-
6.2.2, Table 4(Higher Width)	-	0	-
6.2.2, Table 4(Higher Width)	-	0	-
6.2.2, Table 4(Higher Width)	-	0	-
6.2.2, Table 4(Lower Width)	-	366	-
6.2.2, Table 4(Lower Width)	-	0	-
6.2.2, Table 4(Lower Width)	-	0	-
6.2.2, Table 4(Lower Width)	-	0	-
6.2.2, Table 4(Lower Width)	-	0	-
6.2.2, Table 4(Lower Width)	-	0	-
6.2.2, Table 4(Thickness)	-	366	-
6.2.2, Table 4(Thickness)	-	0	-
6.2.2, Table 4(Thickness)	-	0	-
6.2.2, Table 4(Thickness)	-	0	-
6.2.2, Table 4(Thickness)	-	0	-
6.2.2, Table 4(Thickness)	-	0	-
6.2.2, Table 4(Aspect Ratio)	-	366	-
6.2.2, Table 4(Aspect Ratio)	-	0	-
6.2.2, Table 4(Aspect Ratio)	-	0	-
6.2.2, Table 4(Aspect Ratio)	-	0	-
6.2.2, Table 4(Aspect Ratio)	-	0	-
6.2.2, Table 4(Arris Width wise )	-	366	-
6.2.2, Table 4(Arris Width wise )	-	0	-
6.2.2, Table 4(Arris Width wise )	-	0	-
6.2.2, Table 4(Arris Width wise )	-	0	-
6.2.2, Table 4(Arris Width wise )	-	0	-
6.2.2, Table 4(Arris Width wise )	-	0	-
6.2.6, Table 4(Abrasion Resistance Dry )	-	0	-
6.2.6, Table 4(Abrasion Resistance Dry )	-	0	-
6.2.6, Table 4(Abrasion Resistance Dry )	-	0	-
6.2.6, Table 4(Abrasion Resistance Dry )	-	0	-
6.2.6, Table 4(Abrasion Resistance Dry )	-	0	-
6.2.6, Table 4(Abrasion Resistance Dry )	-	2350	-
6.2.6, Table 4(Abrasion Resistance Wet)	-	0	-
6.2.6, Table 4(Abrasion Resistance Wet)	-	0	-
6.2.6, Table 4(Abrasion Resistance Wet)	-	0	-
6.2.6, Table 4(Abrasion Resistance Wet)	-	0	-
6.2.6, Table 4(Abrasion Resistance Wet)	-	2350	-
6.2.5, Table 4(Compressive strength)	-	0	-
6.2.5, Table 4(Compressive strength)	-	0	-
6.2.5, Table 4(Compressive strength)	-	0	-
6.2.5, Table 4(Compressive strength)	-	0	-
6.2.5, Table 4(Compressive strength)	-	0	-
6.2.5, Table 4(Compressive strength)	-	4700	-
6.2.7, Table 4(Tensile Spliting strength)	-	0	-
6.2.7, Table 4(Tensile Spliting strength)	-	0	-
6.2.7, Table 4(Tensile Spliting strength)	-	0	-
6.2.7, Table 4(Tensile Spliting strength)	-	0	-
6.2.7, Table 4(Tensile Spliting strength)	-	2500	-
6.2.8, Table 4(Flexural strength)	-	0	-
6.2.8, Table 4(Flexural strength)	-	0	-
6.2.8, Table 4(Flexural strength)	-	0	-
6.2.8, Table 4(Flexural strength)	-	2500	-

Complete

31 Dec, 2023

-
-

IS 12817 (2013)

Stainless steel butt hinges - Specification (Second Revision)

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(General - IS 12817 )	-	100	NA
7.2(Knuckles - IS 12817 )	-	250	NA
7.4(Screw Holes- IS 12817 )	-	250	NA
7.4.2(Position of screw holes - IS 12817 )	-	500	NA
7.4.2, Fig 1(The distance of the screw holes from the end of the flap - IS 12817 )	-	250	NA
8(Finish - IS 12817 )	-	200	NA
6.2, Table 1 to 6(Length , A -IS 12817)	-	210	NA
6.2, Table 1 to 6(Breadth, B-IS 12817)	-	180	NA
6.2, Table 1 to 6(Thickness of flap, C-IS 12817)	-	180	NA
6.2, Table 1 to 6(Dia. of Hinge pin, D-IS 12817 )	-	180	Note Reporting charges RS/-200 Clause 4.1.1 Flap RS/- 300, 4.1.2 Pins RS/-200
6.2, Table 1 to 6(Breadth, B1-IS 12817)	-	-	-
6.2, Table 1 to 6(Breadth, B2-IS 12817)	-	-	-
6.2, Table 1 to 6(Number of Knuckles- IS 12817 )	-	-	-
6.2, Table 1 to 6(Number of Screw Holes -IS 12817 )	-	-	-
6.2, Table 1 to 6(Holes for Screw Number- IS 12817 )	-	-	-
7.3(Pins- IS 12817 )	-	-	-

Complete

31 Dec, 2023

-
-

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(General)	-	100	NA
5.2(Dimensions of cover- Diameter)	-	300	NA
9.3 and Table and Annex C(Load Test)	-	500	NA
3(Type/Shape of Cover)	-	300	NA
3(Grade)	-	300	NA
5.2 and Table 1(Dimensions of Frame - A)	-	200	NA
5.2 and Table 1(Dimensions of Frame - B)	-	200	NA
5.2 and Table 1(Dimensions of Frame - C)	-	200	NA
5.2 and Table 1(Dimensions of Frame - D)	-	200	NA
5.2 and Table 1(Dimensions of Frame - E)	-	200	NA
5.2 and Table 1(Dimensions of Frame - F)	-	200	NA
8(LIFTING HOOKS)	-	300	NA
8(LIFTING HOOKS)	-	300	NA
5.2(Clearance at top between the frame and the cover all round the periphery)	-	500	NA
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	500	NA
5.2(Top surface ofthe frame and cover is in level)	-	500	NA
7.4.1(Edge Protection and Finishing - Frame)	-	500	NA
5.2 and Fig 1(Clear cover to reinforcement)	-	500	NA
7.4.1(Edge Protection and Finishing - Frame)	-	1100	NA
7.4.1(Edge Protection and Finishing - Frame)	-	1100	NA

Complete

31 Dec, 2023

-
-

IS 12330 (1988)

Specificatioon for sulphate resisting Portland cement

9000 View breakup
Rs.9000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Fineness 4031 Part 2)	-	400	NA
5.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	400	NA
5.2.1.1(Expansion after aeration - 4031 Part 3)	-	400	NA
5.2.1(Expansion by Autoclave- 4031 Part 3)	-	800	NA
5.2.1.1(Expansion after aeration- 4031 Part 3)	-	800	NA
5.3 a)(Setting Time Initial- 4031 Part 5)	-	200	NA
5.3 b)(Setting Time Final- 4031 Part 5)	-	200	NA
5.4(Salphate Expansion (Optional))	-	800	NA
5.5 i)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	600	NA
5.5 ii)(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	600	NA
5.5 iii)(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	800	NA
5.6(Transverse Strength - IS 4031 Part 8 (Optional))	-	2000	NA
4.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	2400	Silica RS/-1200, Combined oxide RS/-400, Calcium Oxide RS/- 400, Ferric oxide RS/-400
4.1 - Table - 1 ii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	200	NA
4.1 - Table - 1 iii(Magnesia - Cl 4.8 of IS 4032:1985)	-	400	NA
4.1 - Table - 1 iv(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	600	NA
4.1 - Table - 1 vii(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	200	NA
4.1 - Table - 1 v(Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-	2000	NA
4.1 - Table - 1 vi(Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate ( C4AF + 2C3A ) - Cl 4 of IS 4032:1985)	-	800	Note: Reporting charges RS/-200

Complete

31 Dec, 2023

-
Included w.e.f. 05-02-2018

IS 10758 (1983)

Specification for de - Odourizing - Cum - Disinfectant fluids

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.1(Description)	-	300	NA
Cl. 3.2(Volatile matter)	-	400	NA
Cl. 3.2.1(Volatile matter (steam distillation))	-	1000	NA
Cl. 3.3(Stability after dilution(with artificial hard water))	-	200	NA
Cl. 3.4(Persistance of Odour)	-	200	NA
Cl. 3.5(Flash point(abel))	-	400	NA
Cl. 2.1(Germicidal Value)	-	3300	Note: Reporting charges RS/-200

Complete

31 Dec, 2023

-
-

IS 9873 : Part 3 (2020)

Safety of Toys Part 3 Migration of Certain Elements ( Third Revision )

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	400	NA
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	300	NA
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	300	NA
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	300	NA
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	300	NA
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	NA
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	400	NA
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	400	Preparation & extraction of test portions RS/-300

Complete

31 Dec, 2023

-
-

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

4000 View breakup
Rs. 4000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame)	-	3800		Note: Reporting Charges RS-200/-

Complete

31 Dec, 2023

-
-

IS 9825 (2003)

Chlorine tablets - Specification (Second Revision)

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.2(Description)	-	450	NA
Cl.4.3(Available Chlorine (Annex A))	-	600	NA
Cl.4.3(Size (Mass of tablet))	-	550	NA
Cl.4.4(Moisture (Annex B))	-	500	NA
Cl.4.4(Shelf Life (Annex A))	-	1900	NA
Clause 5(Shelf Life)	-	-	-

Complete

31 Dec, 2023

-
-

IS 9103 (1999)

Specification for Concrete Admixtures -

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 9, Table- 2(Dry material content )	-	600	NA
Clause 9, Table- 2(Ash content)	-	500	NA
Clause 9, Table- 2(Relative density)	-	500	NA
Clause 9, Table- 2(Chloride ion content)	-	700	NA
Clause 9, Table- 2( pH)	-	325	NA
Cl 4, Table 1A(Slump)	-	225	NA
Cl 4, Table 1 B(Flow, Loss of workability on satnding, Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	0	NA
Cl 4, Table 1A(Time of setting, allowable deviation from control sample hours)	-	450	NA
Cl 4, Table 1A(Water Content, percent of control sample, Max)	-	450	NA
Cl 4, Table 1A(Compressive strength, percent of control sample, Min)	-	0	NA
Cl 4, Table 1A(Length change, percent increase over control sample, Max)	-	0	NA
Cl 4, Table 1A(Flexural strength, percent of control sample, Min)	-	0	NA
Cl 4, Table 1A(Bleeding, percent increase over control sample, Max)	-	900	NA
Cl 4, Table 1A(Air content (%), Max, over control)	-	900	NA
Cl 4, Table 1 B(Flow)	-	450	NA
Cl 4, Table 1 B(Loss of workability on standing)	-	900	NA
Cl 4, Table 1 B(Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	0	NA
Cl 4, Table 1A(Loss of workability)	-	0	NA
4, Table 1A(Flexural strength percent of control Sample 7 Day)	-	675	-
4, Table 1A(Flexural strength percent of control Sample 28 Day)	-	675	-
4, Table 1A(Flexural strength percent of control Sample 3 Day)	-	675	-
4, Table 1A(Length Change percent Increase over control Sample 28 Day)	-	675	-
4, Table 1A(Length Change percent Increase over control Sample 6 Month)	-	675	-
4, Table 1A(Length Change percent Increase over control Sample 1 year)	-	675	-
4, Table 1A(Compressive strength percent of control Sample 1 Day )	-	337	-
4, Table 1A(Compressive strength percent of control Sample 3 Days)	-	337	-
4, Table 1A(Compressive strength percent of control Sample 7 Days)	-	337	-
4, Table 1A(Compressive strength percent of control Sample 28 Days )	-	337	-
4, Table 1A(Compressive strength percent of control Sample 6 Months )	-	337	-
4, Table 1A(Compressive strength percent of control Sample 1 year )	-	340	-
Clause 4, Table 1B, SI no. (iii) (7 days minimum compressive strength, percent of control mix concrete)	-	506	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 28 days)	-	506	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 6 Months days)	-	506	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 1 Year )	-	507	-

Complete

31 Dec, 2023

-
-

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	400	NA
5.1 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	400	NA
5.1 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	400	NA
5.1 - Table - 1 vi(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	300	NA
6.1(Fineness 4031 Part 2)	-	400	NA
6.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	400	NA
6.2.1(Expansion by Autoclave- 4031 Part 3)	-	800	NA
6.3 a)(Setting Time Initial- 4031 Part 5)	-	250	NA
6.3 b)(Setting Time Final- 4031 Part 5)	-	250	NA
6.4 a)(Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-	900	NA
6.4 b)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	900	NA
6.5(Transverse Strength - IS 4031 Part 8 (Optional))	-	1800	Note: Reporting charges RS/-200
5.1 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	600	Clause 6.4 Silica RS/-1200, Calcium and Ferric oxide RS/-400, Chloride RS/-200, Alkali RS/- 600 Transverse strength (Optional) RS/- 1800
5.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	-	-

Complete

31 Dec, 2023

-
-

IS 6909 (1990)

Supersulphated cement ? specification

9800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	700	NA
5.1(Magnesium Oxide - Cl 4.8 of IS 4032:1985)	-	700	NA
5.1(Sulphuric anhydride - Cl 4.9 of IS 4032:1985)	-	700	NA
5.1(Sulphide sulphur - Cl 6.12 of IS 4032:1985)	-	700	NA
6.1(Fineness 4031 Part 2)	-	500	NA
6.2(Soundness (cold expansion) by Le Chatelier- 4031 Part 3)	-	500	NA
6.3 a)(Setting Time Initial- 4031 Part 5)	-	300	NA
6.3 b)(Setting Time Final- 4031 Part 5)	-	300	NA
6.4 a)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	800	NA
6.4 b)(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	800	NA
6.4 c)(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	900	NA
6.5(Transverse Strength - IS 4031 Part 8 (Optional))	-	200	Note : Clause 5.1 Chloride RS/- 700 Reporting charges RS/- 200
Clause 5.1(12423 : 1988)	-	-	-

Complete

31 Dec, 2023

-
-

IS 6452 (1989)

High alumina cement for structural use - specification (First Revision)

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Fineness IS 4031(Part 2))	-	300	NA
4.3(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	300	NA
4.4(Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-	150	NA
4.4(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	150	NA
4.5(Compretsive Strenqth .24 hrs ± 30min IS 4031(Part 6))	-	800	NA
4.5(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	2000	NA
4.1(Total alumina content (Al2O3) - Cl 4.6 of IS 4032:1985)	-	300	Note: Ferric oxide RS/- 300, Combined oxide RS/-300, Non-compliance with tests RS/-700 Reporting charges RS/- 200

Complete

31 Dec, 2023

-
-

IS 6006 (2014)

Uncoated stress relieved strand for prestressed concrete - Specification (Second Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Length )	-	500	NA
Cl 4(Joints)	-	600	NA
Cl 4(Butt Joint)	-	500	NA
Cl 4.5(Workmanship)	-	300	NA
Cl 5, Table 1(Diameter)	-	300	NA
Cl 5, Table 1(Weight)	-	500	NA
Cl 7.1(Tensile Test On UTM)	-	700	NA
Cl 7.2(Tensile Test On UTM)	-	700	NA
Cl 7.3(Tensile Test On UTM)	-	600	NA
Cl 7.4(Load )	-	0	-
Cl 4(Joints)	-	0	NA
Cl 5(Weight)	-	0	NA
Cl 7(Tensile Test On UTM)	-	0	NA
Cl 7(Tensile Test On UTM)	-	0	NA
Cl 7(Tensile Test On UTM)	-	0	NA
Cl 7(Load )	-	23700	-
Cl 5, Table 1(Diameter)	-	0	-
4.1.2(phosphorus)	-	550	-
4.1.2(sulphur)	-	550	-
Clause 4.1.3(Wire Description)	-	500	-
Clause 4.2(Strand (Difference of center wire and surrounding wire))	-	0	-
Clause 4.2(Forming of Strand)	-	0	-
Clause 5.1, Table-1 (Nominal dia of Element Wire (Two - Wire Strand) )	-	0	-
Clause 5.1, Table-1 (Nominal Area of Strand (Two - Wire Strand) )	-	0	-
Clause 5.1, Table-1 (Nominal Mass of Strand (Two - Wire Strand) )	-	0	-
Clause 5.2, Table-1 (Nominal dia of Element Wire (Three - Wire Strand) )	-	0	-
Clause 5.2, Table-1 (Nominal Area of Strand (Three - Wire Strand) )	-	0	-
Clause 5.2, Table-1 (Nominal Mass of Strand (Three - Wire Strand) )	-	0	-
Clause 5.3, Table-2 (Nominal Diameter of Strand (Seven - Wire Strand) )	-	0	-
Clause 5.3, Table-2 (Nominal Area of Strand (Seven - Wire Strand) )	-	0	-
Clause 5.3, Table-2 (Nominal Mass of Strand (Seven - Wire Strand) )	-	0	-
Clause 7.4(Relaxation Stress (1000 h) )	-	0	-
Clause 7.4.1(Relaxation Stress (100 h) )	-	0	-

Complete

31 Dec, 2023

-
-

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	1500	NA
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	0	NA
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	500	NA
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	300	NA
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	300	NA
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	300	NA
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	200	NA
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	300	NA
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	300	NA
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	200	NA
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	200	NA
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	700	NA
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	700	NA
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	700	Note: Reporting charges RS/-200 Clause 7.1 Lime reactivity RS/-1100
5.1, 7.1, table-2, iii(Lime reacitivity)	-	-	-

Complete

31 Dec, 2023

-
-

IS 3564 (1995)

Hydraulically Regulated Door Closers -Specification

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Nominal Sizes)	-	950	NA
9(Finish)	-	450	NA
B-1.2(a) Visual Inspection)	-	650	NA
B-1.3(b) Surface)	-	250	NA
B-1.4(c) Performance Requirements)	-	6900	NA
B-1.5(d) Endurance Test)	-	4000	NA
8(Essential Requirements)	-	550	NA
8(Essential Requirements)	-	650	NA
8(Essential Requirements)	-	450	NA
8(Essential Requirements)	-	400	NA
8(Essential Requirements)	-	650	NA
8(Essential Requirements)	-	450	Note: Reporting charges RS/-200
9(Finish)	-	-	-
8(Essential Requirements)	-	-	-
Cl. 7 Table 2(Materials)	-	-	-
8(Essential Requirements)	-	-	-
9(Finish)	-	-	-
9(Finish)	-	-	-
8(Essential Requirements)	-	-	-
8(Essential Requirements)	-	-	-
8(Essential Requirements)	-	-	-
8(Essential Requirements)	-	-	-
8(Essential Requirements)	-	-	-
8(Essential Requirements)	-	-	-
Clause 7 (Table 2 - ii)(Material for Torsion spring helical spring)	-	-	-
Clause 7 (Table 2 - iii)(Material for Nuts)	-	-	-
Clause 7 (Table 2 - iv)(Material for Piston or Rack-piston/pinion)	-	-	-
Clause 7 (Table 2 - v)(Material for Material for Packing/washers)	-	-	-
Clause 7 (Table 2 - vi)(Material for Control valve screw)	-	-	-
Clause 7 (Table 2 - vii)(Material for All weather resistant homogeneous high viscosity hydraulic)	-	-	-
Clause 7 (Table 2 - viii)(Material for Adjusting arm)	-	-	-
Clause 7 (Table 2 - ix)(Material for Main arm )	-	-	-
Clause 7 (Table 2 - x)(Material for Clamp)	-	-	-
Clause 7 (Table 2 - xi)(Material for Concentric ratchet ( For bottle type ) )	-	-	-
Clause 7 (Table 2 - xii)(Material for Material for Eccentric shaft )	-	-	-
Clause 7 (Table 2 - xiii)(Material for Internal bearing and gland )	-	-	-
Clause 7 (Table 2 - xiv)(Material for Main arm bolt)	-	-	-
Clause 7 (Table 2 - xv)(Material for Top nut)	-	-	-
Clause 7 (Table 2 - xvi)(Material for Pawl)	-	-	-
Clause 7 (Table 2 - xvii)(Material for Top lid)	-	-	-

Complete

31 Dec, 2023

-
-

IS 3466 (1988)

Specification For Masonry Cement

9900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1 Table 1 i(Fineness IS : 4031:1988)	-	1000	NA
3.1 Table 1 ii a(Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-	400	NA
3.1 Table 1 ii b(Setting Time ( by Vicat Apparatus ), Final IS : 4031:1988)	-	400	NA
3.1 Table 1 iii a(Soundness, Le-Chate1ier expansion IS 4031:1988)	-	600	NA
3.1 Table 1 iii b(Soundness, Autoclave expansion IS 4031:1988)	-	1200	NA
3.1 Table 1 v(Air Content IS 4031:1988)	-	1200	NA
3.1 Table 1 vi(Water Retention IS 4031:1988)	-	2100	NA
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-	1200	NA
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-	1200	NA
4( water soluble alkali content - Cl 9 of IS 4032:1985)	-	600	NA

Complete

31 Dec, 2023

-
-

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

4250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	NA
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	NA
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	NA
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	NA
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	NA
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	NA
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
9( FREEDOM FROM DEFECTS)	-	350	Clause 9.3 Bend RS/- 200 & 9.4 Camber RS/-100
11 & 12(DIMENSIONS and Tolerances)	-	800	NA
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	NA
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	Note: Reporting charges RS/- 200 Clause 6 Cr, Ni, Mo RS/-300 each
11(Dimensions)	-	-	-
10.2(Bend)	-	-	-
10.3(Chamber)	-	-	-
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Clause 6.1.1(IS 2831 : 2012)	-	-	-
Clause 9.3(Bend)	-	-	-
Clause 9.4(Camber)	-	-	-

Complete

31 Dec, 2023

-
-

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

4250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 11(Length)	-	300	NA
Cl 9(Workmanship)	-	250	NA
Cl 10.2(Workmanship)	-	200	NA
Cl 10.3(Workmanship)	-	300	NA
6.1(Carbon %)	-	200	NA
6.1(Manganese %)	-	200	NA
6.1(Phosphorus %)	-	200	NA
6.1(Sulphur %)	-	200	NA
6.1( Copper %)	-	300	NA
6.1(Silicon %)	-	300	NA
6.1( Nb)	-	300	NA
6.1(V)	-	200	NA
6.1( Ti)	-	200	NA
6.1(Cr)	-	200	NA
6.1(Mo)	-	300	NA
6.1(Nitrogen%)	-	200	NA
6.1( Aluminium %)	-	200	NA
6.1(Ni)	-	200	NA
Cl 10.2(Press)	-	-	-
Cl 10.3(Workmanship)	-	-	-
Cl 11(Length, Width & Thickness)	-	-	-
Cl 11(Length, Width & Thickness)	-	-	-
Cl 10.2(Workmanship)	-	-	-
Cl 10.3(Workmanship)	-	-	-
Cl. 10.2(Bend)	-	-	-
Clause 10.3(Camber)	-	-	-
Clause 6.1(IS 2830 : 2012)	-	-	-

Complete

31 Dec, 2023

-
-

First
Prev
2
3
4
5
Next
Last

Bureau of Indian Standards

The National Standards Body of India

IDMA LABORATORIES LIMITED

PLOT NO 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 [email protected]

Scope List

No Record Found

No Record Found