BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- [email protected]

Scope List

Reset

773 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

391

IS 16014 (2018)

Mechanically woven, double - Twisted, hexagonal wire mesh gabions, revet mattresses, rock fall netting and other products for civil engineering purposes (Galvanized Steel Wire Or Galvanized Steel Wire With Polymer Coating) - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (MATERIALS AND MANUFACTURE)	-
5.1.2 (MATERIALS AND MANUFACTURE)	-
5.2 (MATERIALS AND MANUFACTURE)	-
5.3 (MATERIALS AND MANUFACTURE)	-
5.4 (MATERIALS AND MANUFACTURE)	-
5.4.1 (Galvanized Rings)	-
5.4.2 (Stainless Steel Fasteners)	-
6.1 (Tensile Strength)	-
7.1.1 (Mass of Zinc Coating )	-
8.1,Table 1,2,3,4,5,6,i (Mesh wire dia)	-
8.1,Table1,2,3,4,5,6,ii (Edge/Selvedge wire dia)	-
8.1,Table1,2,3,4,5,6,iii (Lacing wire dia)	-
8.1,Table1,2,3,4,5,6,iv (Polymer coating thickness,)	-
8.1,Table1,2,3,4,5,6,v (Typical sizes Length × Width × Height (m))	-
9 (WORKMANSHIP)	-
Clause - 5, 5.1, 5.1.1, 5.1.2, 5.4, 5.4.1, 5.4.2 (CARBON)	-
Clause - 5, 5.1, 5.1.1, 5.1.2, 5.4, 5.4.1, 5.4.2 (SULPHUR)	-
Clause - 5, 5.1, 5.1.1, 5.1.2, 5.4, 5.4.1, 5.4.2 (PHOSPHURS)	-
Clause - 5, 5.1, 5.1.1, 5.1.2, 5.4, 5.4.1, 5.4.2 (MANGANESE)	-
Clause - 5, 5.1, 5.1.1, 5.1.2, 5.4, 5.4.1, 5.4.2 (SILICON)	-
Clause - 5, 5.1, 5.1.1, 5.1.2, 5.4, 5.4.1, 5.4.2 (ALUMINIUM)	-
Clause - 5, 5.1, 5.1.1, 5.1.2, 5.4, 5.4.1, 5.4.2 (NITROGEN)	-
Clause 7.1.1 (Mass of Zinc/Zinc Alloy Coating)	-

Partial

-
-

392

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.1 Table-1 (Dimensional measurement of wires)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor )	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.1 (Stranding)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
11 (Packing and Marking)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-

Complete

-
-

393

IS 15683 (2018)

Portable Fire Extinguishers — Performance and Construction — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.3.1 (Filling Requirements)	-
Cl. 5.3.2 (Filling Requirements)	-
Cl. 5.3.3 (Capacities)	-
Cl. 6 (PRESSURE REQUIREMENTS FOR LOW PRESSURE EXTINGUISHERS)	-
Cl. 7.1 (GENERAL OPERATING PERFORMANCE REQUIREMENTS)	-
Cl. 7.2 - Table 1 (GENERAL OPERATING PERFORMANCE REQUIREMENTS)	-
Cl. 7.2 - Table 1 (GENERAL OPERATING PERFORMANCE REQUIREMENTS)	-
Cl. 7.3 (Resistance to Temperature changes)	-
Cl 7.8 (Intermittent Discharge Test)	-
Cl 7.4.3 ( Leakage Test)	-
Cl 7.5.1 (Impact Resistance Test)	-
Cl 7.7 (Tapping Test)	-
Cl 7.8 (Intermittent Discharge Test)	-
Cl 9.2.2 (Burst Test)	-
Cl 9.2.3 (Crushing Test)	-
Cl 9.2.4 (Pressure Cycling Test)	-
Cl 9.2.5 (Welded Low Carbon Steel Cylinder)	-
Cl 9.2.6 (Stainless Steel Cylinders)	-
Cl 9.2.7 (Aluminium Cylinders)	-
Cl 9.3 (Carrying Handle)	-
Cl 9.4 (Mounting)	-
Cl 9.5 (Caps, Valves and Closures)	-
Cl 9.8 (Hose Assemblies)	-
Cl 9.9 - Table 10 (Method of Operation)	-
Cl 9.10 (Safety-Locking Devices)	-
Cl 9.11.1 (Requirements for Pressure Gauges and Indicators for Low-Pressure Extinguishers)	-
Cl 9.12 (Dip-Tubes and Filters — Water-Based Extinguishers)	-
Cl 9.13 (Horn Test for Carbon Dioxide (CO2) Extinguishers)	-
Cl 10 (MARKING AND COLOUR)	-

Partial

-
-

394

IS 1223 (2001)

Apparatus for determination of milk fat by gerber method - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.3 (Measurement of Various Parts)	-
Cl 4.5 (Body)	-
Cl 4.6 (Condition of the back surface of the tube)	-
Cl 4.7 (Bulb Capacity & Surface)	-
Cl 4.9 (Length)	-
Cl 4.10 (Position)	-
Cl 7.1 (Shape)	-
Cl 7.2 (Materials)	-
Cl 7.3 (Measurement of Various Parts)	-
Cl 13.1 (Materials)	-
Cl 16.3 (Measurement of Various Parts)	-
Cl 19 (Observation of Various Parts)	-
Cl 22.2 (Temperature of Water-bath)	-
CL 4.13 (Numbering of Graduation Lines)	-
CL 4.1.2 (Limit for Alkalinity)	-
CL 4.2.2 (Butyrometers)	-

Complete

-
-

395

IS 14927 : Part 2 (2001)

Cable Trunking and Ducting Systems for Electrical Installations : Part 2 Cable Trunking and Ducting Systems Intended for Mounting on Walls or Ceiling

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-
7.1 (Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-
7.1 (Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-
7.1 (Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-
7.1 (Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-
7.1 (Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-
8.1 ( Dimensions (As per cl.8.1 of IS 14927(Pt-1) : 2001))	-
8.2 (Dimensions (As per cl.8.2 of IS 14927(Pt-1) : 2001)	-
8.3, table 2 ( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-
8.3, table 2 ( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-
8.3, table 2 ( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-
9.1 (Construction)	-
9.2 (Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-
9.2 (Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-
9.3 (Construction ( As per Cl. 9.3 of IS 14927(Pt-1):2001))	-
9.3.1 (Construction ( As per Cl. 9.3.1 of IS 14927(Pt-1):2001))	-
9.3.2, table 3 (Construction ( As per Cl. 9.3.2, Table-3 of IS 14927(Pt-1):2001))	-
9.4.1 (Construction [Access to Live Parts (As per Cl. 9.4.1 of IS 14927(Pt-1):2001)])	-
9.5 (Construction (As per Cl. 9.5 of IS 14927(Pt-1):2001))	-
10.3 (Impact Test [ Cl.10.3 ])	-
10.3.4 (Impact Test (As per Cl. 10.3.4 of IS: 14927(Pt-1):2001) )	-
11.1.1 (Resistance to flame propagation (As per Cl. 11.1.1))	-

Partial

-
-

396

IS 14606 (1998)

Irrigation equipment - Media filters - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4.1 (General )	-
Cl 9 (Back-up Strainer Filter)	-

Partial

-
-

397

IS 4038 (1986)

Foot Valves For Water Works Purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4.2-Table 2 (MANUFACTURE- Flanges-DIMENSIONS AND DRILLING OF FLANGES-Size)	-
4.4.2-Table 2 (MANUFACTURE- Flanges-DIMENSIONS AND DRILLING OF FLANGES-D)	-
4.4.2-Table 2 (MANUFACTURE- Flanges-DIMENSIONS AND DRILLING OF FLANGES-Rhickness of flange)	-
4.4.2-Table 2 (MANUFACTURE- Flanges-DIMENSIONS AND DRILLING OF FLANGES-C)	-
4.4.2-Table 2 (MANUFACTURE- Flanges-DIMENSIONS AND DRILLING OF FLANGES-A)	-
4.4.2-Table 2 (MANUFACTURE- Flanges-DIMENSIONS AND DRILLING OF FLANGES-d)	-
4.4.2-Table 2 (MANUFACTURE- Flanges-DIMENSIONS AND DRILLING OF FLANGES-Dia of bolt)	-
4.5 (MANUFACTURE- Screwed Ends-screwed-ends Polygon side)	-
4.5 (MANUFACTURE- Screwed Ends-screwed)	-
4.5-Table 3 (MANUFACTURE- Screwed Ends-screwed-DIMENSIONS OF SCREWED-END FOOT VALVES-Nominal Size)	-
4.5-Table 3 (MANUFACTURE- Screwed Ends-screwed-DIMENSIONS OF SCREWED-END FOOT VALVES-L)	-
4.5.1-Table 3 (MANUFACTURE- Screwed Ends-screwed-DIMENSIONS OF SCREWED-END FOOT VALVES-H)	-
4.5.2-Table 4 (MANUFACTURE- Screwed Ends-screwed-DIMENSIONS OF SCREWED-END FOOT VALVES-Nominal size)	-
4.5.2-Table 4 (MANUFACTURE- Screwed Ends-screwed-DIMENSIONS OF SCREWED-END FOOT VALVES-D)	-
4.6 (MANUFACTURE- Strainers -Thickness)	-
4.6-Table 5 (MANUFACTURE- Strainers -DIMENSIONS OF STRAINER HOLES -Nominal Size)	-
4.6-Table 5 (MANUFACTURE- Strainers -DIMENSIONS OF STRAINER HOLES -Maximum dia of Hole(Ciecular))	-
4.6-Table 5 (MANUFACTURE- Strainers -DIMENSIONS OF STRAINER HOLES -MAXIMUM VALUE FOR THE Small dimension of the hole(Non-circular))	-
5 (Coating)	-
6.1.1 (Seat Test)	-
6.1.2 (Housing Test)	-

Partial

-
-

398

IS 14203 (2017)

Fire resisting record protection cabinets - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Nominal Sizes)	-
4 (Types)	-
5 (i) Steel components)	-
5 (ii) Brass/ Bronze components)	-
6 (a) Heght)	-
6 (b) Width)	-
6 (c) Depth)	-
6 (d) Height of pedestal)	-
7 (Designation)	-
8.1 (i) Outer body and inner box shall be fabricated from mild steel or galvanised steel sheets of not less than 0.8 mm nominal thickness. The steel parts shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-
8.4 (Handles: Handle shall be made from ferrous (powder coated/ plated), non-ferrous material or polymer)	-
9.1 (The cabinet shall be provided with minimum four shelves for nominal size 1 600, three shelves for nominal size 1 300 and two shelves for cabinets of nominal size 1 000. Shelf height shall be adjustable)	-
10 (Painting)	-
12.1 (Marking:A metal plate showing type of cabinet together with the manufacturer’s name and the year of manufacture shall be fixed on the inner face of the door)	-
12.2 (Marking on Keys: The keys shall be marked with an identification number which shall not be the same as the serial number of the cabinet.)	-

Partial

-
-

399

IS 1363 : Part 1 (2019)

Hexagon Head Bolts, Screws and Nuts of Product Grade ‘C’ Part 1 Hexagon Head Bolts ( Size Range M 5 to M 64 ) ( Fifth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3-Table 1 (Dimensions-d)	-
3-Table 1 (Dimensions-p)	-
3-Table 1 (Dimensions-b)	-
3-Table 1 (Dimensions-c(Maximum))	-
3-Table 1 (Dimensions-da(Maximum))	-
3-Table 1 (Dimensions-ds(Minimum))	-
3-Table 1 (Dimensions-ds(maximum))	-
3-Table 1 (Dimensions-dw(minimum))	-
3-Table 1 (Dimensions-e(minimum))	-
3-Table 1 (Dimensions-k(Minimum))	-
3-Table 1 (Dimensions-k(maximum))	-
3-Table 1 (Dimensions-kw(minimum))	-
3-Table 1 (Dimensions-r(minimum))	-
3-Table 1 (Dimensions-s(minimum))	-
3-Table 1 (Dimensions-s(maximum))	-
3-Table 1 (Dimensions-l(minimum))	-
3-Table 1 (Dimensions-l(maximum))	-
3-Table 1 (Dimensions-ls(minimum))	-
3-Table 1 (Dimensions-lg(maximum))	-
3-Table 1 (Dimensions-u)	-
3-Table 2 (Dimensions-d)	-
3-Table 1 (Dimensions-p)	-
3-Table 1 (Dimensions-b)	-
3-Table 2 (Dimensions-c(Maximum))	-
3-Table 2 (Dimensions-da(Maximum))	-
3-Table 2 (Dimensions-ds(Minimum))	-
3-Table 2 (Dimensions-dw(minimum))	-
3-Table 2 (Dimensions-e(minimum))	-
3-Table 2 (Dimensions-k(Minimum))	-
3-Table 2 (Dimensions-k(maximum))	-
3-Table 2 (Dimensions-kw(minimum))	-
3-Table 2 (Dimensions-s(minimum))	-
3-Table 2 (Dimensions-s(maximum))	-
3-Table 2 (Dimensions-l(minimum))	-
3-Table 2 (Dimensions-l(maximum))	-
3-Table 2 (Dimensions-ls(minimum))	-
3-Table 2 (Dimensions-lg(maximum))	-
3-Table 2 (Dimensions-u)	-
4-Table 3 (Mechanical property-Rockwell hardness (ISO 898-1))	-

Partial

-
-

400

IS 3466 (1988)

Specification For Masonry Cement

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 Table 1 ii a (Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-
3.1 Table 1 ii b (Setting Time ( by Vicat Apparatus ), Final IS : 4031:1988)	-
3.1 Table 1 iii a (Soundness, Le-Chate1ier expansion IS 4031:1988)	-
3.1 Table 1 iii b (Soundness, Autoclave expansion IS 4031:1988)	-
3.1 Table 1 i (Fineness IS : 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-
3.1 Table 1 i (Fineness IS : 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-
Cl.2.2 (Loss on ignition)	-
Cl.2.2 (Total Sulphur Content calculated as Sulphuric Anhydride)	-
Cl.2.2 (Insoluble residue)	-
Cl.2.2 (silica, alumina and iron oxide)	-
Cl.2.2 (Ratio of percentage of alumina to that of iron oxide)	-
Cl.2.2 (Chloride content)	-
Cl.2.2 (Magnesia)	-

Partial

-
-

401

IS 2581 (2002)

Round strand galvanized steel wire ropes for shipping purposes - Specification (Fourth Revision)

- View breakup
Rs 3900/- + charges as per relevant ISS

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5,6.4,Table1-8 (Nominal Rope Diamete)	-
5,6.4,Table1-8 (Approximate Mass)	-
5,6.4,Table1-8 (Minimum Breaking Force Corresponding to Rope Grade )	-
5,Table9-10 (Approximate Mass of Fibre core)	-
5,Table9-10 (Approximate Mass of Steel core)	-
5,Table9-10 (Minimum Breaking Force Corresponding to Rope Grade of 1570, fibre core)	-
5,Table9-10 (Minimum Breaking Force Corresponding to Rope Grade of 1570, Steel core)	-
6.2 (Joints)	-
6.3 (Lay)	-
6.3.1 (The length of lay of the rope shall not be greater than 8 times the nominal diameter of the rope)	-
7,11.2 as per IS 1835 (Uniformity of Zinc Coating-IS 2633)	-
7,11.3 as per IS 1835 (Mass of Zinc Coating-IS 6745)	-
8 (Lubrication )	-

Complete

-
-

402

IS 2096 (1992)

Asbestos cement flat sheets - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (DIMENSIONS AND TOLERANCES - Nominal Thickness)	-
7.2 (DIMENSIONS AND TOLERANCES - Nominal Length and Width)	-
8.4 and 8.5 & 7.3.3.1 & 7.3.3.2 (Tests- 1.Straigthness of edges 2.Squareness of edges)	-
8.6 (Density)	-

Partial

-
-

403

IS 13382 (2018)

Cast iron specials for mechanical and push-on flexible joints for pressure pipes for water, gas and sewage - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Thickness Wall, mm )	-
8.2 (Dimenmsions of Rubber gaskets)	-
10.1 (Tensile Stregth, Mpa)	-
10.2 (Hardness, HBW)	-
12.2 (Dimensions, mm)	-

Partial

-
-

404

IS 1626 : Part 2 (1994)

Asbestos cement building pipes and pipe fittings, gutters and gutter fittings and roofing fittings: Part 2 gutter and gutter fittings) (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (General quality and workmanship)	-
5.1, Fig.1,2&3 Table-1,2,3&4 (Dimension)	-
5.2 Fig.4,5,6&7 (Shape)	-
5.3 (Impermeability test according to the Method 1 described in IS 5913 : 1989)	-

Partial

-
-

405

IS 1592 (2003)

Asbestos cement pressure pipes and joints - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3.4.1 (Length, Diameter (External), Thickness, Regularity Of internal Diameter, Straightness)	-

Partial

-
-

406

IS 15786 (2008)

Prelaminated cement bonded particle board - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 10.3 (Moisture content)	-

Complete

-
-

407

IS 1269 : Part 2 (1997)

Legal metrology - Material measures of length: Part 2 steel tape measures

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Nominal Length)	-
4 (Materials)	-
5 (Construction)	-
6.1 (Graduation)	-
6.2 (Graduation)	-
6.3 (Graduation)	-
6.3.1 (Graduation)	-
6.3.2 (Graduation)	-
6.4 (Graduation)	-
6.5 (Graduation)	-
6.6 (Graduation)	-
6.7 (Graduation)	-
6.8 (Graduation)	-
6.9 (Graduation)	-
6.1O (Graduation)	-
7.1.1 (Numbering-General Requirements)	-
7.2 (Numbering)	-
7.3 (Numbering)	-
7.4 (Numbering)	-
7.5 (Numbering)	-
7.6 (Numbering)	-
7.7 (Numbering)	-
8 (Accuracy Classes & Maximum permissible error)	-
9.1.1 (Automtic Winding Device- Winding Device)	-
9.1.2 (Automtic Winding Device- Case)	-
9.2.2 (Hand Winding Device- Reel)	-
9.2.3 (Hand Winding Device- Case)	-

Partial

-
-

408

IS 13000 (1990)

Silica-asbestos-cement Flat Sheets -

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.2 (Thickness)	-
8.3 (Straightness of Edges)	-
8.4 (Squareness of Edges)	-
6 (General Appearance and Finish)	-
7 (Dimensions and Tolerances)	-
8.6 (Measurement of Density)	-

Partial

-
-

409

IS 14709 (1999)

N - Butyl acrylate - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl No. 3 C-5 and D-5 [ Table 1, Sl no.(i) ] Annex A (Assay)	-
Cl No. 3 C-5 and D-5 [ Table 1, Sl no.(ii)] Annex B (Acidity (as acrylic acid))	-
Cl No. 3 C-5 and D-5 [ Table 1, Sl no.(iii)] Ref to IS 8768 (Colour)	-
Cl No. 3 C-5 and D-5 [ Table 1, Sl no.(iv)] Ref to IS 2362 (Water)	-
Cl No. 3 C-5 and D-5 [ Table 1, Sl no.(v)] Annex C (Inhibitors (as Butyl Etherhydroquinone))	-

Complete

-
-

410

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires Before Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires After Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires Before Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires Before Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires After Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires After Stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
10 (mech) (Stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.4.2 (elec) (Ductility by Elongation Test before stranding)	-
13.4.2 (elec) (Ductility by Elongation Test after stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires Before Stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire before Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
13.7.2 (chem) (Mass of Zinc coating)	-
13.7.2 (chem) (Uniformity of Zinc coating)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-
13.8 Table-4 (mech) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.9 (elec) (Surface condition test)	-

Partial

-
-

411

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 and Table 1 (Dimensions of Frame - A)	-
5.2 and Table 1 (Dimensions of Frame - B)	-
5.2 and Table 1 (Dimensions of Frame - C)	-
5.2 and Table 1 (Dimensions of Frame - D)	-
5.2 and Table 1 (Dimensions of Frame - E)	-
5.2 and Table 1 (Dimensions of Frame - F)	-
5.2 (Dimensions of cover- Diameter)	-
5.2 (Clearance at top between the frame and the cover all round the periphery)	-
5.2 (Top surface ofthe frame and cover is in level)	-
5.2 and Fig 1 (Distance of housing from the edge)	-
5.2 and Fig 1 (Clear cover to reinforcement)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.2 (Edge Protection and Finishing - Cover)	-
8 (LIFTING HOOKS)	-
9.1 (General)	-

Partial

-
-

412

IS 1038 (1983)

Specification For Steel Doors, Windows And Ventilators

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1. (Size-Height)	-
4.1 (Size-Width)	-
5 (Material-Rolled Steel Section)	-
5 (Material-Coupling Section)	-
5 (Material-Glass Panels)	-
6.1 (Frames)	-
6.1.1.1 (Visual Inspection Test)	-
6.1.1.4 (Fillet Weld Test)	-
6.2 (Side Hung Shutter- Thickness of hinge)	-
6.2 (Side Hung Shutter- Pin diameter)	-
6.2 (Side Hung Shutter-Width of hinge)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate- Thicknesss of handle)	-
6.2.3 (Peg Stay - Thickness)	-
6.2.3 (Peg Stay - Dimensions-A)	-
6.2.3 (Peg Stay - Dimensions-B)	-
6.2.3 (Peg Stay - Dimensions-C)	-
6.2.3 (Peg Stay - Dimensions-D)	-
6.2.3 (Peg Stay - Dimensions-E)	-
6.2.3 (Peg Stay - Dimensions-F)	-
6.2.3 (Peg Stay - Dimensions-G)	-
6.2.3 (Peg Stay - Dimensions-H)	-
6.2.3 (Peg Stay - Dimensions-J)	-
6.2.3 (Peg Stay - Dimensions-L)	-
6.2.3 (Peg Stay - Dimensions-M)	-
6.3 (Top Hung Ventilator-Thickness of hinge)	-
6.3 (Top Hung Ventilator-Pin diameter)	-
6.3 (Top Hung Ventilator-Width of hinge)	-

Partial

-
-

413

IS 12427 (2001)

Fasteners - Threaded steel fasteners - Hexagon head transmission tower bolts - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3.1, Cl 3.2, Fig-1, Table-1 & Table-2 (Dimensions)	-
Cl 5.1 & IS 14394 (Nuts)	-
Cl 5.2, IS 2016 & IS 4759 (Washers)	-
Cl 6.1 & IS 1367(Pt 3) (Bolt Tensile,Proof,Wedge Loading,Hardness Test)	-
Cl 7 & IS 1367(Pt 13) (Finish)	-
Cl 8 & IS 1367(Pt 9/Sec1) (General Requirements)	-

Partial

-
-

414

IS 7452 (1990)

Hot rolled steel sections for doors, windows and ventilators - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 6 (Dimensions)	-
cl 7 (MASS AND MASS TOLERANCE)	-
cl 8 (SURFACE FINISH)	-
cl 9 (BEND TEST)	-

Complete

-
-

415

IS 15030 (2001)

Terephthalic acid - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl No 3.2 [ Table 1, Sl no.(ii) ] Annex B (Colour)	-
Cl No 3.2 [ Table 1, Sl no.(iii) ] Annex C (Ash content,)	-
Cl No 3.2 [ Table 1, Sl no.(iv) ] Annex D (Acid value)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (Total of iron, cobalt, manganese and chromium)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (iron)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (cobalt)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (manganese )	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (chromium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (Total of sodium, magnesium, potassium, calcium and Nickel)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (Sodium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (magnesium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (potassium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (calcium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (nickel)	-
Cl No 3.2 [ Table 1, Sl no.(vii) ] Annex G Method A and C (4-carboxybenzaldehyde)	-
Cl No 3.2 [ Table 1, Sl no.(viii) ] Annex G Method A and B (p-toluic acid,)	-
Cl No 3.3 (Particle Size)	-

Partial

-
-

416

IS 4454 : Part 2 (2001)

Steel wire for mechanical springs - Specification february 2001: Part 2 oil hardened and tempered steel wire (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-
7.1, 7.2 (carbon)	-
7.1, 7.2 (sulphur)	-
7.1, 7.2 (phosphorus)	-
7.1, 7.2 (manganese)	-
7.1, 7.2 (silicon )	-
7.1, 7.2 (copper)	-
7.1, 7.2 (Chromium)	-
7.1, 7.2 (Vanadium)	-

Partial

-
-

417

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.2, Table-1 (Measurement of diameter of individual aluminium wire)	-
12.3, Table-1 (Breaking load before stranding)	-
12.3, Table-1 (Breaking load after stranding)	-
12.4 (Wrapping test)	-
12.5, Table 1 (Resistance test)	-
12.6, Table 3 (Measurement of lay ratio)	-
9.3 (Stranding)	-
6 (Freedom from defects)	-

Complete

-
-

418

IS 2721 (2003)

Galvanized steel chain link fence fabric - Specification (Second Revision)

- View breakup
Rs.5950/- (for wire below 5 mm Dia), Rs.6910/- (for wires above 5 mm Dia) and Material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.6.1, 6.2, Table 1 (Mesh Size)	-
Cl.6.3, Table 1 (Width of the fabric)	-
Cl.6.3, Table 1 (Length of the fabric)	-
Cl.6.1, 6.2, Table 1 (Nominal Dia of Mesh wire)	-
Cl. 7.2 and Table 1 (Line Wire (Diameter))	-
Cl. 7.2 and Table 1 (Line Wire (Number of wires))	-
Cl.8 (Chain link fence fabric(Mass of zinc coating)- IS 6745)	-
Cl.9.1.1 (Tensile test of mesh and line wires- IS 1608)	-
Cl.9.1.2 (Wrapping test of mesh and line wires-IS 1755)	-
Cl.9.1.4 (Bend test of mesh and line wires- IS 1608)	-
Cl.9.1.3 (Twist test of mesh and line wires-IS 1717)	-
Cl.9.2 (Line wire (Mass of zinc coating)- IS 6745)	-
Cl.5 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Complete

-
-

419

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Marking, IS 9537-2)	-
6.1 (Marking, IS 9537-2)	-
6.1 (Marking, IS 9537-2)	-
6.2 (Marking, IS 9537-2)	-
6.3 (Marking, Cl. 6.4 of IS 9537-1)	-
7.2.1 (Dimensions, (Minimum outside Diameter), IS 9537-2)	-
7.2.2 (Dimensions (Maximum outside Diameter), IS 9537-2)	-
7.3 (Dimensions (Wall thickness), IS 9537-2)	-
7.3.3 (Uniformity of wall thickness, IS 9537-2)	-
8.1 (Construction, Cl. 8 of IS 9537-1)	-
8.2 (Construction, IS 9537-2)	-
9.3 (Mechanical Properties (Compression Test), IS 9537-2)	-

Partial

-
-

420

IS 4581 (1978)

Specification for phosphorus trichloride, pure and analytical reagent (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description )	-
3.2, Table 1 and A-2 of IS 4581 (Phosphprus Tricloride ( as PCl3 ) - For Analytical Reagent )	-
3.2, Table 1 and A-2 of IS 4581 (Phosphprus Tricloride ( as PCl3 ) - For Pure grade)	-
3.2, Table 1 and A-3 of IS 4581 (Relative density at 27°C/ 27°C - For all Grade)	-
3.2, Table 1 and A-4 of IS 4581 (Evaporation residue, including PCl5 - For All Grades)	-
3.2, Table 1 and A-5 of IS 4581 (Sulphate ( as SO4) - For Analytical Reagent)	-
3.2, Table 1 and A-6 of IS 4581 (Heavy metals (as Pb), - For Analytical Reagent)	-
3.2, Table 1 and A-7 of IS 4581 (Iron ( as Fe ) - For Analytical Reagent)	-

Partial

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- [email protected]

Scope List