BIS - LIMS (Laboratory Information Management System)

Electrical Research and Development Association, gujurat

ERDA Road, GIDC, Makarpura, Vadodara, VADODARA, Vadodara, Gujarat, 390010

9987940924 [email protected]

Scope List

Reset

137 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 12640 : PART 1 (2008)

Residual Current Operated Circuit - Breakers for Household and Similar Uses: Part 1 Circuit-Breakers Without Integral Overcurrent Protection (RCCBs)

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking and other product information)	-	500	-
8.1.1(General)	-	500	-
8.1.2(Mechanism)	-	500	-
8.1.3, Annex-B(Clearances and creepage distances)	-	500	-
8.1.4(Screws, current-carrying parts and connections)	-	500	-
8.1.5(Terminals for external conductors)	-	500	-
8.2(Protection against electric shock)	-	500	-
9.3(Test of indelibility of marking)	-	500	-
9.4(Test of reliability of screws, current-carrying parts and connections)	-	500	-
9.5(Test of reliability of terminals for external conductors)	-	500	-
9.6(Verification of protection against electric shock)	-	500	-
9.7.1.2(Test conditions)	-	500	-
9.7.1.1(Preparation of the RCCB for test)	-	500	-
9.7.2(Insulation resistance of the main circuit)	-	500	-
9.7.3(Dielectric strength of the main circuit)	-	1000	-
9.7.4(Insulation resistance and dielectric strength of auxiliary Gircuits)	-	500	-
9.7.6(Capability of control circuits connected to the main circuit in respect of withstanding high d,c. voltages due to insulation measurements)	-	500	-
9.7.1.1(Verification of impulse withstand voltage across the open contacts (suitability for isolation))	-	2100	-
9.7.7.2(Verification of impulse withstand voltage for the parts not tested in 9.7.7.1)	-	2100	-
9.8.2(Test of temperature-rise - Test procedure)	-	2500	-
9.9.2(Off-load tests with residual sinusoidal alternating currents at the reference temperature of 20 “C & 2 “C)	-	2500	-
9.9.3(Verification of the correct operation with load at the reference temperature)	-	2500	-
9.9.4(Tests at the temperature limits)	-	2500	-
9.10.1(Verification of mechanical and electrical endurance General test conditions)	-	2500	-
9.10.2(Test procedure)	-	2500	-
9.12.1.1(Mechanical shock Test device)	-	1000	-
9.12.2(Mechanical impact)	-	1000	-
9.13(Test of resistance to heat)	-	1000	-
9.14(Test of resistance to abnormal heat and to fire)	-	1000	-
9.15.1(Verification of the trip-free mechanism General test conditions)	-	1000	-
9.16(Verification of the operation of the test device at the limits of rated voltage)	-	1000	-
9.18.1(Verification of the limiting value of overcurrent in case of a load through a RCCB with two current paths)	-	1000	-
9.19.1(Current surge test for all RCCBS (0,5 us/100 kHz ring wave test))	-	6500	-
9.20(Verification of resistance of the insulation against an impulse voltage)	-	6500	-
9.22.1(Climatic test)	-	71000	-
9.21.1.2(Verification of the correct operation in case of suddenly appearing residual pulsating direct currents)	-	2500	-
9.11.2.3(Verification of the rated residual making and breaking capacity)	-	32075	Sequence D1 (3 sample) for Each ratings Sequence D2 (3 sample) for Each ratings
9.11.2.1(Short-circuit tests General conditions for test)	-	1600	HV & Leakage
9.11.2.4(Verification of the coordination between the RCCB and the SCPD)	-	64150	Sequence E (3 sample) for Each ratings Sequence F (3 sample) for Each ratings

Complete

-
-

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

Rated voltage up to :250 V & Rated current up to :16 A

42620 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Ratings)	-	500	-
6.1(RATINGS)	-	0	-
6.2(RATINGS)	-	0	-
7(CLASSIFICATION)	-	500	-
7.1(CLASSIFICATION)	-	0	-
7.1.1(Accessories Classification)	-	0	-
7.1.2(Accessories Classification)	-	0	-
7.1.3(Accessories Classification)	-	0	-
7.1.4(Accessories Classification)	-	0	-
7.1.5(Accessories Classification)	-	0	-
7.2(CLASSIFICATION)	-	0	-
7.2.1(Socket-Outlets Classification)	-	0	-
7.2.2(Socket-Outlets Classification)	-	0	-
7.2.3(Socket-Outlets Classification)	-	0	-
7.2.4(Socket-Outlets Classification)	-	0	-
7.3(Plug Classification)	-	0	-
8(MARKING)	-	500	-
8.1(MARKING)	-	0	-
8.2(MARKING)	-	0	-
8.3(MARKING)	-	0	-
8.4(Marking)	-	0	-
8.5(Marking)	-	0	-
8.6(MARKING)	-	0	-
8.7(MARKING)	-	0	-
8.8(MARKING)	-	0	-
8.9(MARKING)	-	0	-
9(CHECKING OF DIMENSIONS)	-	500	-
9.1(CHECKING OF DIMENSIONS)	-	0	-
9.2(CHECKING OF DIMENSIONS)	-	0	-
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
10.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.2.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.2.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.3(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.4(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.5(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.6(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.7(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
11(PROVISION FOR EARTHING)	-	500	-
11.1(PROVISIONS FOR EARTHING)	-	0	-
11.2(PROVISIONS FOR EARTHING)	-	0	-
11.3(PROVISIONS FOR EARTHING)	-	0	-
11.4(PROVISIONS FOR EARTHING)	-	0	-
11.5(PROVISIONS FOR EARTHING)	-	0	-
11.6(PROVISIONS FOR EARTHING)	-	0	-
12(TERMINALS)	-	500	For screw less terminal Rs: 1800/- For screw less terminal Rs: 3600/- (Combined Socket-outlets)
12.1(TERMINALS)	-	0	-
12.1.1(TERMINALS)	-	0	-
12.1.2(TERMINALS)	-	0	-
12.2(TERMINALS)	-	0	-
12.2.1(TERMINALS)	-	0	-
12.2.2(TERMINALS)	-	0	-
12.2.3(TERMINALS)	-	0	-
12.2.4(TERMINALS)	-	0	-
12.2.5(TERMINALS)	-	0	-
12.2.6(TERMINALS)	-	0	-
12.2.7(TERMINALS)	-	0	-
12.2.8(TERMINALS)	-	0	-
12.2.9(TERMINALS)	-	0	-
12.2.10(TERMINALS)	-	0	-
12.2.11(TERMINALS)	-	0	-
12.3(TERMINALS)	-	0	-
12.3.1(TERMINALS)	-	0	-
12.3.2(TERMINALS)	-	0	-
12.3.3(TERMINALS)	-	0	-
12.3.4(TERMINALS)	-	0	-
12.3.5(TERMINALS)	-	0	-
12.3.6(TERMINALS)	-	0	-
12.3.7(TERMINALS)	-	0	-
12.3.8(TERMINALS)	-	0	-
12.3.9(TERMINALS)	-	0	-
12.3.10(TERMINALS)	-	0	-
12.3.11 (a)(TERMINALS)	-	0	-
12.3.11 (b)(TERMINALS)	-	0	-
12.3.12(TERMINALS)	-	0	-
13(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	500	-
13.1(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.2(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.3(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.4(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.5(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.6(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.7(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.7.1(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.7.2 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.7.3 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.8(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.9(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.1(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.11(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.12(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.13(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.14(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.15(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.16(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.17(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.18(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.19(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.2(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.21(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.22(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
13.23(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	0	-
14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.6(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.7(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.8(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.9(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.10.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.10.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.10.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.11(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.15(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.23(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.23.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.23.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.26(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
15(INTERLOCKED SOCKET-OUTLETS)	-	0	-
16(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	3350	If sample is marked IP protection than additional charges are applicable as under in addition to above test charges : IP3X to IP4X: 850, IP5X to IP6X: 3300, IPX1 to IP X6 :1300 IPX7 to IPX8: 2200
16.1(RESISTANCE TO AGEING,)	-	0	-
16.2(RESISTANCE TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	0	-
16.2.1(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	5500	If sample is marked IP protection than additional charges are applicable as under in addition to above test charges : IP23: 2275 IP33, IP34, IP43, IP44, IP53, IP54, IP55, IP56, IP65, IP66: 4600 IP67, IP68 : 5500
16.2.1.1(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	0	-
16.2.1.2(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	3300	If sample is marked IP protection than additional charges are applicable as under in addition to above test charges : IP3X to IP4X: 850, IP5X to IP6X: 3300, IPX1 to IP X6 :1300 IPX7 to IPX8: 2200
16.2.2(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	0	-
16.3(Resistance to Humidity)	-	0	-
17(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
17.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
17.1.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
17.1.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
17.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
17.3(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
18(OPERATION OF EARTHING CONTACTS)	-	500	-
19(TEMPERATURE RISE)	-	650	TEMPERATURE RISE --COMBINED SOCKET-OUTLETS : RS. 1300/-
19.1(TEMPERATURE RISE)	-	0	-
19.2(TEMPERATURE RISE)	-	0	-
19.3(TEMPERATURE RISE)	-	0	-
20(BREAKING CAPACITY)	-	1300	MAKING & BREAKING CAPACITY - COMBINED SOCKET-OUTLETS: Rs. 3200/- MAKING & BREAKING CAPACITY- PLUGS : Rs. 2700/-
21(NORMAL OPERATION)	-	4100	NORMAL OPERATION - COMBINED SOCKET-OUTLETS: Rs. 8200/- NORMAL OPERATION - PLUGS : Rs. 4100/-
21(NORMAL OPERATION)	-	0	-
21(NORMAL OPERATION)	-	0	-
21(NORMAL OPERATION)	-	0	-
22.1(Verification of the Maximum Withdrawal Force)	-	500	-
22.2(Verification of Minimum Withdrawal Force)	-	0	-
23(FLEXIBLE CABLES AND THEIR CONNECTION)	-	500	FLEXIBLE CABLE & THEIR CONNECTION -FOR NON REWIRABLE PLUGS : Rs. 800/-
23.1(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
23.2(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
23.3(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
23.4(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
24.1(MECHANICAL STRENGTH For all kinds of fixed socket-outlets )	-	900	MECHANICAL STRENGTH (ORDINARY- SOCKET-OUTLETS): Rs. 900/- MECHANICAL STRENGTH (ORDINARY- SOCKET-OUTLETS- COMBINED): Rs. 1700/- MECHANICAL STRENGTH (ORDINARY- PLUG) : Rs. 1100/- MECHANICAL STRENGTH -PLUG PROVIDED WITH INSULATED SLEEVE : Rs. 3500/-
24.1(MECHANICAL STRENGTH For portable multiple and combined socket outlets with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	0	-
24.1(MECHANICAL STRENGTH For surface mounting boxes)	-	0	-
24.2(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	0	-
24.2(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	0	-
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies other than elastomeric or thermoplastic material)	-	0	-
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	0	-
24.3(MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-	0	-
24.4(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	0	-
24.4(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	0	-
24.4(MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	0	-
24.5(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	0	-
24.5(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	0	-
24.5(MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	0	-
24.6(MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-	0	-
24.7(MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-	0	-
24.8(MECHANICAL STRENGTH For shuttered socket-outlets)	-	0	-
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	0	-
24.1(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	0	-
24.1(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	0	-
24.11(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	0	-
24.12(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	0	-
24.13(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	0	-
24.14.1(MECHANICAL STRENGTH For fixed socket-outlets)	-	0	-
24.14.2(MECHANICAL STRENGTH For fixed socket-outlets)	-	0	-
24.14.3(MECHANICAL STRENGTH For plugs and portable socket-outlets)	-	0	-
24.15(MECHANICAL STRENGTH )	-	0	-
24.16(MECHANICAL STRENGTH )	-	0	-
24.17(MECHANICAL STRENGTH)	-	0	-
24.18(MECHANICAL STRENGTH)	-	0	-
24.19(MECHANICAL STRENGTH)	-	0	-
25(RESISTANCE TO HEAT)	-	500	-
25.1(RESISTANCE TO HEAT Accessories and surface mounting boxes)	-	0	-
25.2(RESISTANCE TO HEAT Parts of insulating material necessary to retain current-carrying parts of the earthing circuit in position, as well as parts of the front surface zone of thermoplastic material)	-	0	-
25.3(RESISTANCE TO HEAT Parts of insulating material not necessary to retain current-carrying parts and parts of the earthing circuit in position, even though they are in contact with them)	-	0	-
25.4(RESISTANCE TO HEAT )	-	0	-
26(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	2000	SCREWS, CURRENT CARRYING PARTS & CONNECTIONS-COMBINED SOCKET-OUTLETS : Rs. 2500/-
26.1(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.2(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.3(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.4(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.5(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.6(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.7(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
27(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	500	-
27.1(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	0	-
27.2(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	0	-
27.3(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	0	-
28.1.1(Resistance to Abnormal Heat and to Fire Glow-Wire Test)	-	2400	-
28.1.2(Resistance to Abnormal Heat and to Fire for plugs with pins provided with insulating sleeves)	-	0	-
28.2(Resistance to Tracking For accessories other than IP code higher than IPX0 parts of insulating material retaining live parts in position)	-	2070	-
29(RESISTANCE TO RUSTING)	-	500	-
30.1(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-	750	-
30.2(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-	5300	-
30.3(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-	1700	-
30.4(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-	4500	-

Complete

-
-

IS 16227 : Part 2 (2016)

Instrument transformers: Part 2 additional requirements for current transformers

56725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.6(Test for accuracy)	-	11550	metering LTCT : 2100/- per core per tap per ratio metering above LT to 33kV CT : 2750/- per core per tap per ratio metering above 33 to 132kV CT : 4600/- per core per tap per ratio special protection turn ratio error :1350/ - per core per tap per ratio
7.5.2(Determination of the instrument security factor (FS) of measuring current transformers)	-	3150	per core per tap per ratio
7.3.201(Determination of secondaty winding resistance)	-	630	per core per tap per ratio
7.3.203(Test for rated knee point e.m.f. (Ek) and exciting current at Ek)	-	1050	per core per tap per ratio
7.3.204(Inter-turn overvoltage test)	-	525	per core per tap per ratio
7.2.2(Temperature-rise test)	-	8925	up to 200A : 3150/- above 200A to 1000A : 5250/- above 1000A to 2500A : 8400/- above 2500A to 5000A : 8925/-
7.2.6.203(Test for composite error of class P and PR protective current transformers)	-	3900	per core per tap per ratio

Complete

-
-

IS 16227 : Part 1 (2016)

Instrument transformers: Part 1 general requirements

104430 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.3.6(Verification of markings)	-	525	per ratio , per core, per tap
7.3.3(Power-frequency voltage withstand tests between sections)	-	525	per ratio , per core, per tap
7.3.4(Power-frequency voltage withstand tests on secondary terminals)	-	525	per ratio , per core, per tap
7.3.1(Power-frequency voltage withstand tests on primary terminals)	-	11550	2310/- up to 33kV 4725/- up to 33-66kV 5775/- for 66-132kV 11550/- for 132-220kV
7.3.2(Partial discharge measurement)	-	20000	5250/- up to 33kV 7350/- above 33 -up to 66kV 15000/- above 66 -up to 132kV 20000/- above 132kV - up to 220kV

Complete

-
-

IS 16444 : Part 2 (2017)

AC static transformer operated watthour and var - Hour smart meters, class 0.2 S, 0.5 S and 1.0 S: Part 2 specification transformer operated smart meters

Class 0.2S, 0.5S and 1.0S

311050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(General Constructional requirements)	-	3000	-
6.2(Meter case)	-	0	Charges Covered in General Constructional requirements
6.2(Window)	-	0	Charges Covered in General Constructional requirements
6.2(Communication module)	-	0	Charges Covered in General Constructional requirements
6.2.1(Terminals, terminal block and protective earth terminal)	-	0	Charges Covered in General Constructional requirements
6.2.1(Heat Deflection Test)	-	2300	-
6.2.2(Terminal Cover(s))	-	0	Charges Covered in General Constructional requirements
6.2.2(Insulating encased meter)	-	0	Charges Covered in General Constructional requirements
6.3(Clearance and creepage distances)	-	0	Charges Covered in General Constructional requirements
6.6(Display of measured values)	-	2000	-
6.7(Output device)	-	5000	-
6.8(Marking of meters Name plate)	-	2000	-
6.8(BIS Standard Mark)	-	0	Charges Covered in Marking of meters
6.8(Connection diagrams and terminal marking)	-	0	Charges Covered in Marking of meters
6.8.1(Additional information)	-	0	Charges Covered in Marking of meters
6.10.6(Impulse voltage test)	-	7590	-
6.10.6(ac high voltage test)	-	1000	-
6.10.6(Insulation test)	-	1000	-
6.12(Test on limits of error)	-	2200	-
6.12(Test of meter constant)	-	1000	-
6.12(Test of starting condition)	-	1000	-
6.12(Test of no-load condition)	-	1000	-
6.12(Test of ambient temperature influence)	-	965	-
6.12(Test of repeatability of error)	-	3450	-
6.12(Test of influence quantities)	-	1930	Charges for Auxiliary Voltage and Phase of auxiliary supply voltage by 120 deg.
6.12(Voltage Variation)	-	965	-
6.12(Frequency Variation)	-	965	-
6.12(Waveform 10% of 3rd Harmonics)	-	965	-
6.12(Reversed Phase Sequence)	-	965	-
6.12(Voltage Unbalanced)	-	965	-
6.12(Continuous Magnetic Induction of External Origin 67 milli Tesla)	-	965	-
6.12(Continuous Magnetic Induction of External Origin 0.2 Tesla)	-	965	-
6.12(Magnetic induction of External Origin 0.5mT)	-	965	-
6.12(Abnormal Magnetic Induction of External Origin 10mT)	-	965	-
6.12(Operation of Accessories)	-	1150	-
6.10.1(Test of power consumption)	-	1000	-
6.10.2(Test of influence of supply voltage)	-	2070	-
6.10.3(Test of influence of short time over currents)	-	3450	-
6.10.4(Test of influence of self-heating)	-	1380	-
6.10.5(Test of influence of heating)	-	575	-
6.10.7(Test of immunity to earth/phase fault)	-	965	-
6.11(Radio interference measurement)	-	11550	-
6.11(Fast transient burst test)	-	8325	-
6.11(Test of immunity to electrostatic discharge)	-	6475	-
6.11(Test of immunity to electromagnetic HF field)	-	34650	-
6.11(Surge Immunity test)	-	7500	-
6.9(Dry heat test)	-	2070	-
6.9(Cold test)	-	12280	-
6.9(Damp heat cyclic test)	-	12970	-
6.5(Vibration test)	-	15640	-
6.5(Shock test)	-	11590	-
6.5(Spring hammer test)	-	575	-
6.5(Test of protection against penetration of dust and water)	-	10465	-
Note a of Table 1(Accuracy of the meter at pre-defined points)	-	1500	-
Note b of Table 1(Access and data read test)	-	5000	-
6.4(Test of resistance to heat and fire)	-	5750	-
7, 9.4(Data Exchange for Electricity Meter Reading, Tariff and Load Control Companion Specification (The requirement as per IS 15959 : Part 1 & Part 3 shall apply))	-	96000	Rs. 60,000/- for Single Port RS. 36,000/- for Two Ports
9.3(Test of Display)	-	2000	-
8, 9.5(Smart Meter Communicability)	-	6000	-
10.0(Smart Meter Functional Requirements)	-	6000	-

Complete

-
-

IS 16444 (2015)

AC static direct connected watthour smart meter class 1 and 2 - Specification

Class 1 and 2

625825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.9.2 of IS 13779(Test for Immunity to Electrostatic Discharge (ESD))	-	0	Not Applicable as Standard Refer IS 15884
12.9.3 of IS 13779(Test for Immunity to EIectromagnetic HF Fields)	-	0	Not Applicable as Standard Refer IS 15884
12.9.4 of IS 13779(FastTransient BurstTest)	-	0	Not Applicable as Standard Refer IS 15884
12.9.5 of IS 13779(Radio Interference Measurement)	-	0	Not Applicable as Standard Refer IS 15884
cl. 12.7.6.2 of IS 13779(Impulse voltage test)	-	7590	-
cl. 12.7.6.3 of IS 13779(ac Voltage test)	-	575	-
cl. 12.7.6.4 of IS 13779(Insulation resistance test)	-	575	-
cl 11.1 of IS 13779(Limits of Error and Interpretation or Test Results)	-	1520	-
12.15 of IS 13779(Test of Meter Constant/Registration)	-	690	-
12.14 of IS 13779(Test of Starting Conditions)	-	690	-
12.13 of IS 13779(Test of No-Load Condition)	-	690	-
12.12 of IS 13779(Test ofAmbient Temperature Influence)	-	965	-
12.17 of IS 13779(Repeatability of Error Test )	-	3450	-
12.11 of IS 13779(Test of Iniluence Quantities)	-	10800	-
12.7.1 of IS 13779(Test of Power Consumption)	-	0	Not Applicable as Standard Refer IS 15884
12.7.2 of IS 13779(Test of Influence of Supply Voltage)	-	0	Not Applicable as Standard Refer IS 15884
12.7.3 of IS 13779( Test of Influence of Short-time Overcurrents)	-	0	Not Applicable as Standard Refer IS 15884
12.7.4 of IS 13779(Test of Influence of Self-Heating)	-	0	Not Applicable as Standard Refer IS 15884
12.7.5 of IS 13779(Test of Influence of Heating)	-	0	Not Applicable as Standard Refer IS 15884
12.8 of IS 13779(TestorImmunity to Earth Fault)	-	965	-
12.6.1 of IS 13779(Dry Heat Test)	-	2070	-
12.6.2 of IS 13779(Cold Test)	-	12280	-
12.6.3 of IS 13779( Damp Heat Cycle Test)	-	12970	-
12.3.1 of IS 13779(Shock Test)	-	11590	-
12.3.3 of IS 13779( Spring Hammer Test)	-	575	-
12.4 of IS 13779(Testof Resistance to Heat and Fire )	-	5750	-
4.4.2.1 of IS 15844(Voltage range)	-	0	Charges Covered in Test of Influence of Supply Voltage
4.4.2.2 of IS 15844( Specified operating range )	-	0	Charges Covered in Test of Influence of Supply Voltage
4.4.2.3 of IS 15844(Extended operating range)	-	0	Charges Covered in Test of Influence of Supply Voltage
4.4.2.4 of IS 15844( Limit range of operation)	-	0	Charges Covered in Test of Influence of Supply Voltage
4.4.2.5 of IS 15844(Withstand range)	-	0	Charges Covered in Test of Influence of Supply Voltage
4.4.2.6 of IS 15844(Abnormal voltage conditions)	-	0	Charges Covered in Test of Influence of Supply Voltage
4.4.2.7 of IS 15844(Voltage dips and short interruptions)	-	0	Charges Covered in Test of Influence of Supply Voltage
cl. 7.1 a) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 b) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 c) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 d) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 e) of of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 f) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 g) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 h) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 j) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 k) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 m) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 n) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
cl. 7.1 p) of IS 13779(MARKING OF METERS : Name Plate )	-	0	Charges Covered in Marking of smart meters
6.2.1(Heat Deflection Test)	-	2300	-
12.3.2 of IS 13779(Vibration Test)	-	15640	-
6.5(Vibration test)	-	15640	-
4.4.3 of IS 15844(Influence of Short-Time Overcurrents)	-	3450	-
4.4.4 of IS 15844(Influence of Self-Heating)	-	1380	-
4.4.5 of IS 15844(Influence of Heating)	-	575	-
4.4.6 of IS 15844(Insulation)	-	575	-
6.8(BIS Standard Mark)	-	0	Charges Covered in Marking of smart meters
6.8(Marking of smart meters Name plate)	-	2000	-
6.3(Clearance and creepage distances)	-	0	Charges Covered in General and constructional requirements
11.0(Smart meter functional requirements)	-	6000	-
9, 10.6(Test of Smart Meter Communicability)	-	6000	-
10.3(Test of Display)	-	2000	-
8.0(Data Exchange for Electricity Meter Reading, Tariff and Load Control Companion Specification (Verification up to two Port))	-	96000	-
7.2, 10.4(Performance Requirements for Load Switching (UC1))	-	60000	-
7.2, 10.4(Dielectric strength (G-8))	-	19500	-
7.2, 10.4(Minimum switched current (G-7))	-	9000	-
7.2, 10.4(Short circuit current carrying capacity (G-6))	-	31000	-
7.2, 10.4(Fault current making capacity (G-5))	-	56000	-
7.2, 10.4(Line to load voltage surge withstand (G-4))	-	7500	-
7.2, 10.4(Electrical endurance (G-3))	-	80000	-
7.2, 10.4(Normal operation (G-2))	-	6000	-
6.5(Test of resistance to heat and fire)	-	5750	-
Note 1c of Table 1(Remote disconnect/connect)	-	5000	-
Note 1b of Table 1(Access and data read test)	-	5000	-
Note 1a of Table 1(Accuracy of the meter at pre-defined points)	-	1500	-
6.5(Spring Hammer test)	-	575	-
6.5(Shock test)	-	11590	-
6.9(Damp heat cyclic test)	-	12970	-
6.9(Cold test)	-	12280	-
6.9(Dry heat test)	-	2070	-
6.11(Test of immunity to electromagnetic HF field)	-	34650	-
6.11(Test of immunity to electrostatic discharge)	-	6600	-
6.11(Fast transient burst test)	-	8325	-
6.11(Radio interference measurement)	-	54250	-
6.10.7(Test of influence of immunity to earth fault)	-	965	-
6.10.5(Test of influence of heating)	-	575	-
6.10.4(Test of influence of self-heating)	-	1380	-
6.10.1(Test of influence of short time over currents)	-	3450	Cl. No. 6.10.3 of IS 16444 Part 1
6.10.1(Test of influence of supply voltage)	-	3870	Cl. No. 6.10.2 of IS 16444 (Part 1
6.10.1(Test of power consumption)	-	575	-
6.12(Operation of Accessories)	-	1150	-
6.12(Abnormal Magnetic Induction of External Origin 10mT)	-	965	-
6.12(Magnetic induction of External Origin 0.5mT)	-	965	-
6.12(Continuous Magnetic Induction of External Origin 0.2 Tesla)	-	965	-
6.12(Continuous Magnetic Induction of External Origin 67 milli Tesla)	-	965	-
6.12(DC & Even Harmonics in the ac current circuit)	-	965	-
6.12(Voltage Unbalanced)	-	965	-
6.12(Reversed Phase Sequence)	-	965	-
6.12(Waveform 10% of 3rd Harmonics)	-	965	-
6.12(Frequency Variation)	-	965	-
6.12(Voltage Variation)	-	965	-
6.12(Test of influence quantities)	-	0	Test wise Charges are added
6.12(Test of repeatability of error )	-	3450	-
6.12(Test of ambient temperature influence)	-	965	-
6.12(Test of no-load condition)	-	690	-
6.12(Test of starting condition)	-	690	-
6.12(Test of meter constant)	-	690	-
6.12(Test on limits of error due to variation of the current)	-	1520	-
6.10.6(Insulation resistance test)	-	575	-
6.10.6(ac high voltage test)	-	575	-
6.10.6(Impulse voltage test)	-	7590	-
6.8.1(Additional information)	-	0	Charges Covered in Marking of smart meters
6.8(Connection diagrams and terminal marking)	-	0	Charges Covered in Marking of smart meters
6.7(Output device)	-	5000	-
6.6(Display of measured values)	-	2000	-
6.2.2(Insulating encased meter)	-	0	Charges Covered in General and constructional requirements
6.2.2(Terminal Cover(s))	-	0	Charges Covered in General and constructional requirements
6.2.1(Terminals, terminal block and protective earth ter-minal)	-	0	Charges Covered in General and constructional requirements
6.2(Communication module Load switch)	-	0	Charges Covered in General and constructional requirements
6.2(Window)	-	0	Charges Covered in General and constructional requirements
6.2(Meter case)	-	0	Charges Covered in General and constructional requirements
6.2(General and constructional requirements)	-	3000	-
6.11(Surge Immunity test)	-	7500	-
12.5 a) of IS 13779(Test of Protection Against Penetration of Dust and Water)	-	10465	-
12.5 b) of IS 13779(Test of Protection Against Penetration of Dust and Water)	-	0	Charges Covered in 12.5 a
6.5(Protection against penetration of dust and water)	-	10465	-

Complete

-
-

IS 14697 (1999)

AC static transformer operated , watthour and var - Hour meters, class 0.2 S and 0.5 S - Specification

Class 0.2S, 0.5S and 1.0S

172855 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.7.6.2(Impulse voltage test )	-	7590	-
12.7.6.3(ac Voltage test)	-	575	-
12.7.6.4(Insulation resistance test)	-	575	-
11.1(Limits of Error Due to Variation of the Current)	-	1520	-
12.14(Test of Meter Constant/ Registration)	-	690	-
12.13(Test of Starting Conditions)	-	690	-
12.12(Test of No-Load Condition)	-	690	-
12.11(Test of Ambient Temperature Influence)	-	965	-
12.16(Repeatability of Error Test)	-	3450	-
12.1(Test of Influence Quantities)	-	0	Separate test wise charges added in individual test
12.7.1(Test of Power Consumption )	-	575	-
12.7.2(Test of Influence of Supply Voltage)	-	2070	-
12.7.3(Test of Influence of Short-Time Over Currents)	-	3450	-
12.7.4(Test of influence of self-heating)	-	1380	-
12.7.5(Test of Influence of Heating )	-	575	-
12.6.1(dry heat test)	-	2070	-
12.6.2(cold test)	-	12280	-
12.6.3(Damp Heat Cycle Test )	-	12970	-
12.3.3(Spring Hammer Test)	-	575	-
12.3.1(Shock Test)	-	11590	-
12.4(Test of Resistance to Heat and Fire)	-	5750	-
12.8.2(Test for Immunity to Electrostatic Discharge (ESD))	-	6475	-
12.8.3(Test for Immunity to Electromagnetic HF Fields )	-	34650	-
12.8.4(Fast Transient Burst Tes)	-	8325	-
12.8.5(Radio interference measurement)	-	11550	-
6.4(Heat Deflection Test)	-	2300	-
12.3.2(Vibration Test)	-	11500	-
12.5(Test of protection against penetration of dust and water)	-	10465	-
6.1(General)	-	690	-
6.2(Meter case)	-	0	Test charges included in General (Cl. No. 6.1)
6.3(Window)	-	0	Test charges included in General (Cl. No. 6.1)
6.4(Terminals, terminal block and protective earth terminal)	-	0	Test charges included in General (Cl. No. 6.1)
6.5(Terminal Cover(s))	-	0	Test charges included in General (Cl. No. 6.1)
6.6(Clearance and creepage distances)	-	0	Test charges included in General (Cl. No. 6.1)
6.7(Insulating encased meter)	-	0	Test charges included in General (Cl. No. 6.1)
6.10(Display of measured values)	-	0	Test charges included in General (Cl. No. 6.1)
6.11(Output device)	-	0	Test charges included in General (Cl. No. 6.1)
7.1 a)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 b)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 c)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 d)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 e)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 f)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 g)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 h)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 j)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 k)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 m)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1 n)( MARKING OF METERS: Name Plate )	-	0	Test charges included in General (Cl. No. 6.1)
7.1(Marking of meters Name plate)	-	0	Test charges included in General (Cl. No. 6.1)
7.1.1(Bis marking)	-	0	Test charges included in General (Cl. No. 6.1)
7.2(Connection Diagrams and Terminal Marking)	-	0	Test charges included in General (Cl. No. 6.1)
12.1(Voltage Variation)	-	965	-
12.1(Frequency Variation)	-	965	-
12.1(Waveform 10% of 3rd Harmonics)	-	965	-
12.1(Reversed Phase Sequence)	-	965	-
12.1(Voltage Unbalanced)	-	965	-
12.1(Auxiliary Voltage)	-	965	-
12.1(Phase of Auxiliary Voltage)	-	965	-
12.1(Continuous Magnetic Induction of External Origin 67 milli Tesla)	-	965	-
12.1(Continuous Magnetic Induction of External Origin 0.2 Tesla)	-	965	-
12.1(Magnetic induction of External Origin 0.5mT)	-	965	-
12.1(Abnormal Magnetic Induction of External Origin 10mT)	-	965	-
12.1(Operation of Accessories)	-	1150	-
12.3.2(Vibration test)	-	4140	Charges for Pre & Post Error of Vibration Test
12.17(Test of immunity to earth/phase fault)	-	965	-

Complete

-
-

IS 9335 : Part 3 : Sec 5 (1985)

Specification for cellulosic papers for electrical purposes: Part 3 specifications for individual materials: Sec 5 special papers

All

41883 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, Table 5 to 8(Thickness)	-	575	-
5, Table 5 to 8(Substance)	-	1150	-
5, Table 5 to 8(Apparent density)	-	1725	-
5, Table 5 to 8(Tensile strength)	-	1725	-
5, Table 5 to 8(elongation)	-	0	Test Charges included in Tensile Strength test.
5, Table 5 to 8(Internal tearing resistance)	-	1725	-
5, Table 5 to 8(Bursting strength)	-	1150	-
5, Table 5 to 8(Moisture Content)	-	1150	-
5, Table 5 to 8(Ash)	-	1725	-
5, Table 5 to 8(Conductivity of Aqueous Extract)	-	1725	-
5, Table 5 to 8(pH of Aqueous Extract)	-	1725	-
5, Table 5 to 8(Air permeability)	-	1150	-
5, Table 5 to 8(Water absorption)	-	920	-
5, Table 5 to 8(Electric strength)	-	1150	-
5, Table 5 to 8(Dissipation factor of dry un impregnated paper)	-	2875	-
5, Table 5 to 8(Heat Stability)	-	21413	-

Complete

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

- View breakup
Rs. 1,25,450/- ; Multicore cables: additional charges Rs. 500/- per core per test. Restricted to Rs. 24,975/- for single core unarmoured cable, Rs. 33,750/- for two core, unarmoured cable, Rs. 40,050/- for two core armoured cable (Excluding addl. Type test for cables with improved fire performance.) For multi core cables, extra charges @ 35 % for each additional core shall be levied. Material testing charges as per relevant referred ISs Testing charges for Additional Type Tests for Improved Fire Performance Tests: Rs. 10,650/- for category C1 Rs. 17,550/- for category C2 for BIS Samples

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

- View breakup
Rs. 1,14,000/- ; Multicore cables: additional charges Rs. 500/- per core per test.; Restricted to For category 01 Unsheathed cable: A Single Core, Plain Copper Conductor Rs. 15,750/- B Single Core, Tinned Copper Conductor Rs. 16,200/- C Single Core, Solid Aluminium Conductor Rs. 15,300/- D Single Core, Stranded Aluminium ConductorRs. 15,300/- Sheathed Cable: A Single Core, Plain Copper Conductor Rs. 26,325/- B Single Core, Tinned Copper Conductor Rs. 26,775/- C Single Core, Solid Aluminium ConductorRs. 25,875/- D Single Core, Stranded Aluminium Conductor Rs. 25,875/- For category 02 Unsheathed Cable: A Single Core, Plain Copper Conductor Rs. 18,225/- B Single Core, Tinned Copper Conductor Rs. 18,675/- C Single Core, Solid Aluminium Conductor Rs. 17,775/- D Single Core, Stranded Aluminium Conductor Rs. 17,775/- Sheathed Cable: A Single Core, Plain Copper Conductor Rs. 28,350/- B Single Core, Tinned Copper Conductor Rs. 28,800/- C Single Core, Solid Aluminium Conductor Rs. 27,900/- D Single Core, Stranded Aluminium Conductor Rs. 27,900/- For FR cables Unsheathed Cable: A Single Core, Plain Copper Conductor Rs. 18,900/- B Single Core, Tinned Copper Conductor Rs. 19,350/- C Single Core, Solid Aluminium Conductor Rs. 18,450/- D Single Core, Stranded Aluminium Conductor Rs. 18,450/- Sheathed Cable: A Single Core, Plain Copper Conductor Rs. 29,475/- B Single Core, Tinned Copper Conductor Rs. 29,925/- C Single Core, Solid Aluminium Conductor Rs. 29,025/- D Single Core, Stranded Aluminium Conductor Rs. 29,025/- For FR-LSH cables Unsheathed Cable A Single Core, Plain Copper Conductor Rs. 20,925/- B Single Core, Tinned Copper Conductor Rs. 21,375/- C Single Core, Solid Aluminium Conductor Rs. 20,475/- D Single Core, Stranded Aluminium Conductor Rs. 20,475/- Sheathed Cable: A Single Core, Plain Copper Conductor Rs. 31,230/- B Single Core, Tinned Copper Conductor Rs. 31,680/- C Single Core, Solid Aluminium Conductor Rs. 30,780/- D Single Core, Stranded Aluminium Conductor Rs. 30,780/- Material testing charges as per relevant referred Iss (For each of the above category). For multi core cable: for each additional core, the charges of single core unsheathed cable as per material (copper & aluminum) and as per construction of conductor (solid or standard, tinned or plain) shall be added for BIS Samples

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 16102 : Part 2 (2017)

Self - Ballasted led lamps for general lighting services: Part 2 performance requirements (First Revision)

210900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Dimensions)	-	1000	-
8(Lamp Input)	-	19400	Test Charges included of Harmonics and power factor: 6000 Rs. & Test Charges of EMISSION (RADIATED AND CONDUCTED) OF RADIO FREQUENCY DISTURBANCE: 13400 Rs. Total Test charges : (6000 + 13400)= 19400 Rs.
9(light output)	-	45000	Test charges included of Luminous flux: 25000 Rs. and Test charges for center beam intensity and Beam angle : 20000 Rs. Total test charges : (25000 + 20000) =45000 Rs.
10(Colour Nomenclature, Variation and Rendering)	-	25000	-
11(Lamp Life)	-	120000	-

Complete

-
-

IS 335 (2018)

New insulating oils - Specification (Fifth Revision)

40425 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Viscosity)	-	1640	Viscosity at 40C Rs. 410/- Viscosity at 0 C Rs. 410/- Viscosity at -30C Rs. 410/- Viscosity at -40C Rs. 410/-
6.2(Pour Point)	-	570	Per Sample
6..3(Water Content)	-	1280	Per Sample
6.4(Breakdown Voltage)	-	710	Per Sample
6.5(Dielectric Dissipation Factor (DDF))	-	990	Per Sample
6.6(Appearance)	-	180	Per Sample
6.7(Acidity)	-	520	Per Sample
6.8(Interfacial Tension (IFT))	-	410	Per Sample
6.15(Flash Point)	-	410	Per Sample
6.1(Corrosive Sulphur and Potentially Corrosive Sulphur)	-	1380	Per Sample
6.11(Additives)	-	1150	Per Sample
6.12(Oxidation Stability)	-	5180	Per Sample
6.16(Density)	-	410	Per Sample
6.19(2-Furfural (2-FAL) and Related Compounds Content)	-	3700	Per Sample
6.9(Sulphur Content)	-	7475	Per Sample
6.13(Gassing Tendency)	-	5570	Per Sample
6.17(Polycyclic Aromatics (PCA))	-	8850	Per sample

Complete

-
-

IS 1293 (2005)

Plugs and socket- outlets of rated voltage up to and including 250 volts and rated current up to 16 amperes

Plugs and sockets-outlets of rated voltage up to and in

14775 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Ratings)	-	100	-
6.0(Ratings)	-	0	-
7.0(Classification)	-	100	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
7.0(Classification)	-	0	-
8.0(Marking)	-	100	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
8.0(Marking)	-	0	-
9.0(Checking of dimensions)	-	200	-
9.0(6A/10A )	-	0	-
9.0(6A/10A )	-	0	-
9.0(6A/10A )	-	0	-
9.0(16 A)	-	0	-
9.0(16 A)	-	0	-
9.0(16 A)	-	0	-
10.1(Protection against Electric Shock)	-	0	-
10.1(Protection against Electric Shock)	-	0	-
10.3(Protection against Electric Shock)	-	0	-
10.5(Protection against Electric Shock)	-	0	-
10.6(Protection against Electric Shock)	-	0	-
11.1(Provision for Earthing)	-	0	-
11.2(Provision for Earthing)	-	0	-
11.5(Provision for Earthing)	-	0	-
12.1(Terminals)	-	0	-
12.2.1(Terminals)	-	0	-
12.2.2(Terminals)	-	0	-
12.2.3(Terminals)	-	0	-
12.2.4(Terminals)	-	0	-
12.2.5(Terminals)	-	0	-
12.2.7(Terminals)	-	0	-
12.2.9(Terminals)	-	0	-
12.2.10(Terminals)	-	0	-
12.2.11(Terminals)	-	0	-
13.1(Construction of fixed Socket Outlets)	-	0	-
13.2(Construction of fixed Socket Outlets)	-	0	-
13.3(Construction of fixed Socket Outlets)	-	0	-
13.4(Construction of fixed Socket Outlets)	-	0	-
13.4(Construction of fixed Socket Outlets)	-	0	-
13.4(Construction of fixed Socket Outlets)	-	0	-
13.4(Construction of fixed Socket Outlets)	-	0	-
13.4(Construction of fixed Socket Outlets)	-	0	-
13.5(Construction of fixed Socket Outlets)	-	0	-
13.9(Construction of fixed Socket Outlets)	-	0	-
13.1(Construction of fixed Socket Outlets)	-	0	-
13.16(Construction of fixed Socket Outlets)	-	0	-
13.14(Construction of fixed Socket Outlets)	-	0	-
13.17(Construction of fixed Socket Outlets)	-	0	-
15.0(Interlocked socket-outlets)	-	0	-
16.1(Resistance to Ageing )	-	0	-
16.2(Resistance to Harmful Ingress of Water)	-	0	-
16.3(Resistance to humidity)	-	0	-
17.1(Insulation Resistance)	-	0	-
17.2( Electric Strength)	-	0	-
18.0(Operation of Earthing Contacts)	-	200	-
19.0(Temperature Rise )	-	1350	-
20.0(Making & Breaking Capacity)	-	1500	-
21.0(Normal Operation)	-	3150	-
21.0(Normal Operation)	-	0	-
21.0(Normal Operation)	-	0	-
21.0(Normal Operation)	-	0	-
22.1(Verification of Max withdrawal force)	-	0	-
22.2(Verification of Minimum withdrawal force)	-	0	-
24.1(a) Mechanical Strength )	-	0	-
24.3(a) For surface type socket outlet)	-	0	-
24.6(b) For screwed glands of accessories other than ordinary)	-	0	-
24.8(c) For shuttered socket-outlets )	-	0	-
24.14.1(e)Verification of the Non-removal of Covers or Cover-Plates )	-	0	-
24.14.2(f)Verification of the Removal of Covers or Cover-Plates )	-	0	-
25.1(Resistance to heat)	-	0	-
25.2(Resistance to heat)	-	0	-
25.3(Resistance to heat)	-	0	-
25.4(Resistance to heat)	-	0	-
26.1(Screws, current carrying parts and connections)	-	0	-
26.2(Screws, current carrying parts and connections)	-	0	-
26.7(Screws, current carrying parts and connections)	-	0	-
27.1(Creepage distances, clearances and distances through sealing compound )	-	0	-
27.2(Creepage distances, clearances and distances through sealing compound )	-	0	-
27.3(Creepage distances, clearances and distances through sealing compound )	-	0	-
28.1.1(Glow-Wire Test )	-	0	-
28.2(Resistance to Tracking)	-	500	-
29.0(Resistance to Rusting)	-	100	-
6(RATINGS)	-	0	-
6.1(RATINGS)	-	0	-
6.2(RATINGS)	-	0	-
7(CLASSIFICATION)	-	0	-
7.1(CLASSIFICATION)	-	0	-
7.1.1 (CLASSIFICATION)	-	0	-
7.1.2(CLASSIFICATION)	-	0	-
7.1.3 (CLASSIFICATION)	-	0	-
7.1.4(CLASSIFICATION)	-	0	-
7.2(CLASSIFICATION)	-	0	-
7.2.1(CLASSIFICATION)	-	0	-
7.2.2 (CLASSIFICATION)	-	0	-
7.2.3(CLASSIFICATION)	-	0	-
7.2.4(CLASSIFICATION)	-	0	-
7.2.5(CLASSIFICATION)	-	0	-
7.3(CLASSIFICATION)	-	0	-
8.1(MARKING)	-	0	-
8.2(MARKING)	-	0	-
8.3(MARKING)	-	0	-
8.4(MARKING)	-	0	-
8.5(MARKING)	-	0	-
8.6(MARKING)	-	0	-
8.7(MARKING)	-	0	-
8.8(MARKING)	-	0	-
9.1(CHECKING OF DIMENSIONS)	-	0	-
9.2(CHECKING OF DIMENSIONS)	-	0	-
9.3(CHECKING OF DIMENSIONS)	-	0	-
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	200	-
10.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.2.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.3(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.5(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.6(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.7(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
11(PROVISION FOR EARTHING)	-	200	-
11.1(PROVISION FOR EARTHING)	-	0	-
11.2(PROVISION FOR EARTHING)	-	0	-
11.3(PROVISION FOR EARTHING)	-	0	-
11.4(PROVISION FOR EARTHING)	-	0	-
11.5(PROVISION FOR EARTHING)	-	0	-
6.2(RATINGS)	-	0	-
7.1(CLASSIFICATION)	-	0	-
7.1.1 (CLASSIFICATION)	-	0	-
7.1.2(CLASSIFICATION)	-	0	-
7.1.3 (CLASSIFICATION)	-	0	-
7.1.4(CLASSIFICATION)	-	0	-
7.2(CLASSIFICATION)	-	0	-
7.2.1(CLASSIFICATION)	-	0	-
7.2.2 (CLASSIFICATION)	-	0	-
7.2.3(CLASSIFICATION)	-	0	-
7.2.4(CLASSIFICATION)	-	0	-
7.2.5(CLASSIFICATION)	-	0	-
7.3(CLASSIFICATION)	-	0	-
8.1(MARKING)	-	0	-
8.2(MARKING)	-	0	-
8.3(MARKING)	-	0	-
8.4(MARKING)	-	0	-
8.7(MARKING)	-	0	-
8.8(MARKING)	-	0	-
9.1(CHECKING OF DIMENSIONS)	-	0	-
9.2(CHECKING OF DIMENSIONS)	-	0	-
9.3(CHECKING OF DIMENSIONS)	-	0	-
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.2.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.2.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.4(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
10.7(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
11(PROVISION FOR EARTHING)	-	0	-
11.3(PROVISION FOR EARTHING)	-	0	-
11.4(PROVISION FOR EARTHING)	-	0	-
12(TERMINALS)	-	3275	-
12.1.1(TERMINALS)	-	0	-
12.1.2(TERMINALS)	-	0	-
12.2(TERMINALS)	-	0	-
12.2.1(TERMINALS)	-	0	-
12.2.6(TERMINALS)	-	0	-
12.2.8(TERMINALS)	-	0	-
12.3(TERMINALS)	-	0	-
12.3.1(TERMINALS)	-	0	-
12.3.2(TERMINALS)	-	0	-
12.3.3(TERMINALS)	-	0	-
12.3.4(TERMINALS)	-	0	-
12.3.5(TERMINALS)	-	0	-
12.3.6(TERMINALS)	-	0	-
12.3.7(TERMINALS)	-	0	-
12.3.8(TERMINALS)	-	0	-
12.3.9(TERMINALS)	-	0	-
12.3.10(TERMINALS)	-	0	-
12.3.11 (a)(TERMINALS)	-	0	-
12.3.11 (b)(TERMINALS)	-	0	-
12.3.12 (TERMINALS)	-	0	-
13(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	200	-
13.7(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.7.1(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.7.2 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.7.3 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.8(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.11(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.12(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.13(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.15(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.18(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.19(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.2(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.21(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.22(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
13.23(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	0	-
14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	100	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.6(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.7(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.8(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.9(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.11(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.15(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.23(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.23.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.23.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	0	-
16(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	1750	-
17(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	200	-
17.1.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
17.1.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
17.3(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	0	-
22(FORCE NECESSARY TO WITHDRAW THE PLUG)	-	200	-
23(FLEXIBLE CABLES AND THEIR CONNECTION)	-	250	-
23.1(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
23.2(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
23.3(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
23.4(FLEXIBLE CABLES AND THEIR CONNECTION)	-	0	-
24(MECHANICAL STRENGTH)	-	200	-
24.1(MECHANICAL STRENGTH)	-	0	-
24.2(MECHANICAL STRENGTH)	-	0	-
24.3(MECHANICAL STRENGTH)	-	0	-
24.4(MECHANICAL STRENGTH)	-	0	-
24.5(MECHANICAL STRENGTH)	-	0	-
24.6(MECHANICAL STRENGTH)	-	0	-
24.7(MECHANICAL STRENGTH)	-	0	-
24.8(MECHANICAL STRENGTH)	-	0	-
24.9(MECHANICAL STRENGTH)	-	0	-
24.1(MECHANICAL STRENGTH)	-	0	-
24.11(MECHANICAL STRENGTH)	-	0	-
24.12(MECHANICAL STRENGTH)	-	0	-
24.13(MECHANICAL STRENGTH)	-	0	-
24.14(MECHANICAL STRENGTH)	-	0	-
24.14.1(MECHANICAL STRENGTH)	-	0	-
24.14.2(MECHANICAL STRENGTH)	-	0	-
24.15 & 24.14.1(MECHANICAL STRENGTH)	-	0	-
24.15 & 24.14.2(MECHANICAL STRENGTH)	-	0	-
24.16 & 24.14.1(MECHANICAL STRENGTH)	-	0	-
24.16 & 24.14.2(MECHANICAL STRENGTH)	-	0	-
24.17(MECHANICAL STRENGTH)	-	0	-
24.18(MECHANICAL STRENGTH)	-	0	-
25(RESISTANCE TO HEAT)	-	100	-
25.1(Resistance to heat)	-	0	-
26(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	200	-
26.3(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.4(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.5(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
26.6(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	0	-
27(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	-
28(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	850	-
28.1(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	0	-
28.1.2(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	0	-
30(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES)	-	2175	-
30.1(Addiitional tests on pins provided with insulating sleeves - Pressure Test at High Temperature)	-	0	-
30.2(Addiitional tests on pins provided with insulating sleeves - Static Damp Heat Test)	-	0	-
30.3(Addiitional tests on pins provided with insulating sleeves - Impact Test at Low Temperature)	-	0	-
30.4(Addiitional tests on pins provided with insulating sleeves - Tests at Low Temperature)	-	0	-

Complete

-
-

IS 11037 (2019)

Electronic Type Fan Regulators — Specification ( First Revision )

Electronic type fan regulator for use with single phase

26025 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1 (a)(Marking )	-	500	-
9.1 (b)(Marking )	-	0	-
9.1 (c)(Marking )	-	0	-
9.1 (d)(Marking )	-	0	-
9.1 (e)(Marking )	-	0	-
9.1 (f)(Marking )	-	0	-
9.2(Marking )	-	0	-
6.1(Design and General Construction)	-	500	-
6.2(Design and General Construction)	-	0	-
6.3(Design and General Construction)	-	0	-
6.5(Design and General Construction)	-	0	-
6.6(Design and General Construction)	-	0	-
9.5.1 , 7.3(Temperature Rise)	-	850	-
9.5.1 , 7.3 (a)(Temperature Rise )	-	0	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	0	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	0	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	0	-
9.5.2, 7.2(Leakage Current Test(as per Cl.13.2 of IS 302 (Part 1).)	-	500	-
9.5.3(High Voltage Test)	-	500	-
9.5.5(Earthing Connection)	-	500	-
9.5.6(Protection against electric shock (as per Cl.8 of IS 302 (Part 1))	-	500	-
7.6(General and safety requirements)	-	1700	-
7.7(Voltage drop)	-	500	-
8.1(Performance)	-	800	-
8.2(Performance)	-	0	-
8.3(Performance)	-	0	-
9.5.7, 9.5.4(Moisture Resistance )	-	3350	-
7.4.1(a)(Mechanical strength )	-	500	-
7.4.1(b)(Mechanical strength )	-	0	-
9.5.8, (Mechanical strength (as per Cl.21.1 of IS 302-1:2008))	-	500	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	500	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	0	-
9.5.10( Electrical Endurance Test)	-	4800	-
9.5.11.2(Environmental Tests)	-	1525	-
9.5.11.3(Environmental Tests)	-	750	-
9.5.11.4(Environmental Tests)	-	3800	-
9.5.12(Resistance to Abnormal Heat and to Fire)	-	2450	-
9.5.12.1(Resistance to Abnormal Heat and to Fire)	-	0	-
9.5.13(Resistance to Rusting )	-	500	-
9.5.14(Checking of Dimensions)	-	500	-

Complete

-
-

IS 4289 : Part 2 (2000)

Flexible cables for lifts and other flexible connections - Specification: Part 2 pvc insulated circular cables

- View breakup
Type tests Rs. 37,900/- ; Multicore cables: additional charges Rs. 500/- per core per test.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 13730 : Part 34 (2000)

Specifications for particular types of winding wires: Part 34 polyester enamelled round copper wire, class 130 L (First Revision)

- View breakup
Rs.8,30,500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 4159 (2002)

Mineral filled sheathed heating elements - Specification (Third Revision)

Air and water heaters up to and including 5 kW

20153 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 33.1 of IS 4159:2002(Finish Test )	-	500		-
Cl.18 of IS 4159:2002(Endurance Test )	-	3453		-

Complete

-
-

IS 9968 : Part 2 (2002)

Specification for elastomer - Insulated cables: Part 2 for working voltages from 3.3 kV up to and including 33 kV (First Revision)

- View breakup
Rs. 1,85,847/- for 1 Core (Upto 11 kV) ; Rs. 1,95,297/- for 1 Core (Above 11 kV) ; Rs. 2,20,497/- for 3 Core (Upto 11 kV) ; Rs. 2,29,947/- for 3 Core (Above 11 kV) ; Multicore cables: additional charges Rs. 500/- per core per test; Restricted to Rs. 21,675/- for single core cables Excluding Partial discharge test, bending test followed by partial discharge test, Heating cycle test followed by partial discharge test, impulse withstand test. For each additional core extra charges @25 % for each additional core shall be levied for BIS Samples

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 15111 : PART 1 AND PART 2 (2002)

Self ballasted lamps for general lighting services: Part 1 safety requirements

13140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	280	-
7(Interchangeability )	-	390	-
8(Protection against electric shock)	-	150	-
9.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH After HUMIDIT’Y TREATMENT)	-	2970	-
10(Mechanical strength test )	-	480	-
11(Cap Temperature rise test )	-	1600	-
12(Resistance to heat)	-	650	-
13(Resistance to Flame and Ignition)	-	2780	-
14(Fault Conditions)	-	3840	Fault condition to be conducted on 6 Nos. lamps. Hence, total test charges for fault condition lamp is Rs.640 x 6 = Rs.3840/-

Complete

-
-

IS 15111 : Part 2 (2002)

Self ballasted lamps for general lighting services: Part 2 performance requirements

63810 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(DIMENSIONS)	-	370	-
8.1(STARTING AND RUN-UP)	-	720	-
8.2(STARTING AND RUN-UP)	-	0	-
9(Lamp Wattage)	-	0	Combine test charges of Lamp wattage, Luminous flux, PF and Efficacy is : 2410 Rs.
10(Luminous Flux)	-	2410	-
11(Colour)	-	1560	-
12(LUMEN MAINTENANCE)	-	0	-
13.1(Life)	-	43790	Combine Test charges for Lumen maintenance at 2000 hours and Life test up to 6000 Hrs is 43790 Rs.
13.2(Life)	-	0	-
14(Harmonics)	-	1560	-
16(Power factor)	-	0	-
18.1(Marking)	-	0	-
15(Lamp Efficacy)	-	0	-

Complete

-
-

IS/IEC 60034 : PART 1 (2004)

Rotating electrical machines : Part 1 Rating and performance

- View breakup
Up to 5.5kW: Rs. 7,090/-, 5.5kW to 11kW : Rs. 8,625/-, 11kW to 22kW: Rs. 13,839/-, 22.1kW to 45kW : Rs. 19,600/-, 45.1 to 75 kW : Rs. 25,400/-, 75.1 to 110 kw ; Rs. 33,200/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 1258 (2005)

Bayonet lamp holders (Fourth Revision)

48800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Rating )	-	500	-
6(Rating )	-	0	-
7(Classification)	-	500	-
7.2(Classification)	-	0	-
7.3(Classification)	-	0	-
7.4(Classification)	-	0	-
7.5(Classification)	-	0	-
7.6(Classification)	-	0	-
8.1(Marking )	-	500	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.2(Marking )	-	0	-
8.2(Marking )	-	0	-
8.2(Marking )	-	0	-
8.3(Marking )	-	0	-
8.4(Marking )	-	0	-
8.5(Marking )	-	0	-
8.6(Marking )	-	0	-
8.7(Marking )	-	0	-
8.8(Marking )	-	0	-
9.1(Dimensions)	-	500	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.2(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
10(Protection against electric shock )	-	500	-
11.1(Terminals)	-	1800	TERMINALS-SCREW TYPE : Rs. 500/- TERMINALS-SCREW less TYPE : 1800/-
11.2(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.4(Terminals)	-	0	-
12(Provision for Earthing)	-	500	-
13.1(Construction)	-	500	-
13.1(Construction (Data Sheet No 7005-10))	-	0	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	0	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	0	-
13.3(Construction )	-	0	-
13.4(Construction )	-	0	-
13.5(Construction)	-	0	-
13.2 ,13.6 & 13.7 (Construction)	-	0	-
13.2 ,13.6 & 13.8(Construction)	-	0	-
13.11(Construction)	-	0	-
14(Construction)	-	0	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1250	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
16.1(Mechanical Strength)	-	550	-
16.1(Mechanical Strength)	-	0	-
16.2(Mechanical Strength)	-	0	-
16.3(Mechanical Strength)	-	0	-
16.4(Mechanical Strength)	-	0	-
16.5(Mechanical Strength)	-	0	-
16.6 & Table - 6(Mechanical Strength)	-	0	-
16.7(Mechanical Strength)	-	0	-
16.8(Mechanical Strength)	-	0	-
17(Screws,current-carrying parts and connections)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
19.1(General resistance to heat)	-	32500	GENERAL RESISTANCE TO HEAT -FOR LH WITHOUT TEMP. MARKING OR MARKED Txxx : Rs. 3850/- GENERAL RESISTANCE TO HEAT- FOR LH MARKED T1 OR T2 : Rs. 32500/-
19.2(General resistance to heat)	-	0	-
19.3(General resistance to heat)	-	0	-
19.4(Resistance to heat test)	-	0	-
20.1(Resistance to heat, fire and tracking)	-	5450	-
20.3(Resistance to heat, fire and tracking)	-	0	-
20.4(Resistance to heat, fire and tracking)	-	0	-
20.5(Resistance to tracking)	-	0	-
21.1(Resistance to excessive residual stresses and to rusting)	-	2250	-
21.1(Resistance to excessive residual stresses and to rusting)	-	0	-

Complete

-
-

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

24094 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	184	NA
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	414	NA
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	345	NA
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	161	NA
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	161	NA
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	161	NA
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	690	NA
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	690	NA
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	552	NA
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	690	NA
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	1656	NA
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	5934	NA
8(Thermal Properties (Cl..8.4))	-	1140	NA
8(Thermal Properties (Cl..8.4))	-	3795	NA
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3726	NA
8(Extreme Low Temperature (Cl.8.6))	-	3795	NA

Complete

-
-

IS 302 : Part 2 : Sec 30 (2007)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 30 room heaters (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 302 : Part 2 : Sec 201 (2008)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 201 electric immersion water heaters (First Revision)

- View breakup
Rs. 21,800/- ; Restricted to Rs. 10,350/- for 1kW to 3kW for BIS Samples

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 302 : Part 1 (2008)

Safety of household and similar electrical appliances: Part 1 general requirements (Sixth Revision)

- View breakup
Rs. 1,21,300/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 4253 : Part 2 (2008)

Cork composition sheets - Specification: Part 2 cork and rubber (Second Revision)

All Type

- View breakup
Rs.14030/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

- View breakup
Rs.23350/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 15884 (2010)

Alternating current direct connected static prepayment meters for active energy (Class 1 And 2) - Specification

Class 1 and 2

559813 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.6.2(6 KV, As per cl 12.7.6.2 of IS 13779)	-	7500	-
5.4.6.3(Table 15, power source 500 VA)	-	2000	-
5.4.6.4(500±50V dc)	-	1500	-
4.6.1(As per table 10 & 11, cl 5.6.1)	-	4500	-
5.6.5(As per cl 4.6.5)	-	1500	For Single Phase meter Rs. 1000/-
5.6.4(As per cl 4.6.3, Table 13)	-	1500	For Single Phase meter Rs. 1000/-
5.6.3(I= open circuit V= 115% of rated voltage test period 60 000/k minutes)	-	1500	For Single Phase meter Rs. 1000/-
5.6.7(Test shall be carried out at 0.05Ib and Ib at UPF load under reference conditions. Twenty error samples shall be taken at time-intervals of 30 minutes)	-	5000	For Single Phase meter Rs. 4000/-
4.6.2(As per table 12)	-	14530	-
5.4.1(As per 4.4.1.1)	-	1500	-
5.4.2(As per 4.4.2.1)	-	4800	Testing Charges Including Abnormal Voltage Test Charges Rs. 1800/-
5.4.3(Table 8, as per cl4.4.3)	-	3000	-
5.4.4(Table 9, and cl 4.4.4)	-	3000	-
5.4.5(As per cl 4.4.5)	-	2500	-
5.3.1(according to IS 9000 (Part 3/ Sec 1 to 5))	-	3000	-
5.3.2(according to IS 9000 (Part 2/Sec 1 to 4))	-	9000	-
5.3.3(according to IS 9000 (Part 5/Sec 1 and 2))	-	10000	-
5.2.2(As per IS 9000 (Part 7/Sec 1))	-	9000	-
5.2.1(As per cl 12.3.3 of IS 13779)	-	1000	-
5.2.4(As per IS 11000 (Part 2 / Sec1))	-	5000	For Single Phase meter Rs. 3000/-
5.5.5(according to IEC 62052-11)	-	54250	For Single Phase meter Rs. 52820/-
5.5.4(according to IS 14700 (Part 4/Sec 4))	-	8325	For Single Phase meter Rs. 7400/-
5.5.3(Table 12 & IS 14700 (Part 4/Sec 3))	-	34650	-
5.5.2(according to IS 14700 (Part 4/Sec 2))	-	6600	For Single Phase meter Rs. 5950/-
5.5.6(Surge Immunity Test)	-	7500	-
4.2.4(IS 13360 (Part 6/Sec 17) for a temperature of 135°C and a pressure of 1.8 MPa (Method A).)	-	2300	-
5.2.3(As per IS 9000 (Part 8))	-	13000	For Single Phase meter Rs. 11200/-
4.1.1(By Inspection)	-	0	Test Charges included in General Mechanical Requirements
4.1.2(By Inspection)	-	0	Test Charges included in General Mechanical Requirements
4.1.3(By Inspection)	-	0	Test Charges included in General Mechanical Requirements
4.1.4(By Inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.1(By Inspection)	-	1800	-
4.2.2(By Inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.3(By Inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.4(By Inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.5(shall have a separate cover which can be sealed independently of the meter cover. The terminal cover shall enclose the actual terminals)	-	0	Test Charges included in General Mechanical Requirements
4.2.6(By measurement)	-	0	Test Charges included in General Mechanical Requirements
4.2.7(Standard test fingure)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.2(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.3(By measurement)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.4(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.5(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.6(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.7(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.10.8(General requirements- Mechanical and electrical characteristics)	-	3000	-
4.2.10.9(General requirements- Optical characteristics)	-	3000	-
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.11.1(By inspection)	-	0	Test Charges included in General Mechanical Requirements
4.2.12.3(Keypad Interface)	-	42000	-
4.6.3(Limits of error due to Ambient temperature Variation)	-	2500	For Single Phase meter Rs. 2000/-
5.2.5(Protection against penetration of dust (IP5X))	-	12558	-
5.2.5(Protection against penetration of water (IP1X))	-	0	Test Charges included in Protection against penetration of dust (IP5X)
5.8(Test of Load Switch)	-	2000	-
5.9(Test of Consumption-Based charging function)	-	3000	-
5.10(Test of Time-Based charging function)	-	3000	-
3.12.6, 4.6.6.2.1 & 5.1.7(Load Switching Capability (UC1))	-	60000	-
4.6.6.2.2 & G2(Normal operation)	-	6000	-
4.6.6.2.2 & G3(Electrical endurance)	-	80000	-
4.6.6.2.2 & G4(Line to load voltage surge withstand)	-	7500	-
4.6.6.2.2 & G5(Fault current making capacity)	-	56000	-
4.6.6.2.2 & G6(Short circuit current carrying capacity)	-	31000	-
4.6.6.2.2 & G7(Minimum switched current)	-	9000	-
4.6.6.2.2 & G8(Dielectric strength)	-	19500	-

Complete

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Electrical Research and Development Association, gujurat

ERDA Road, GIDC, Makarpura, Vadodara, VADODARA, Vadodara, Gujarat, 390010

9987940924 [email protected]

Scope List

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found