BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Office Laboratory (NROL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- [email protected]

Scope List

Reset

290 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

211

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
20.13 (Test for Halogen Acid Gas Evolution)	-
4.1 (CONDUCTOR)	-
4.1.1 (CONDUCTOR)	-
5 (INSULATION)	-
6 (SCREENING)	-
6.1.1 (SCREENING : - Non-metallic — Semiconducting Compound)	-
6.1.2 (SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-
7 (FILLERS AND INNER SHEATH)	-
8.1 (ARMOURING)	-
8.2 (ARMOURING)	-
9 (OUTER SHEATH )	-
10.1 (CONDUCTOR)	-
10.2 (CONDUCTOR)	-
11 (CONDUCTOR SCREENING)	-
12.1 (INSULATION)	-
12.2 (INSULATION : Thickness of Insulation)	-
12.3 (INSULATION : Tolerance on Thickness of Insulation)	-
12.4 (Eccentricity and Ovality)	-
12.5 (INSULATION : Application of Insulation)	-
13.1 (INSULATION SCREENING)	-
13.2 (INSULATION SCREENING)	-
13.3 (INSULATION SCREENING)	-
13.4 (INSULATION SCREENING)	-
14.1 (CORE IDENTIFICATION)	-
14.1.1 (CORE IDENTIFICATION)	-
15.1 (LAVING UP OF CORES)	-
16.1 (INNER SHEATH (COMMON COVERING))	-
16.2 (INNER SHEATH (COMMON COVERING))	-
16.2.1 (INNER SHEATH (COMMON COVERING))	-
16.3 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
16.3.1 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
17.1 (ARMOURING : Application )	-
17.1.1 (ARMOURING )	-
17.1.2 (ARMOURING )	-
17.1.3 (ARMOURING )	-
17.2 (ARMOURING : Type of armour )	-
17.2.1 (ARMOURING : Type of armour )	-
17.2 (ARMOURING : Coverage )	-
17.3 (ARMOURING : Dimension )	-
17.4 (ARMOURING : Joints)	-
16.4 (ARMOURING : Resistance)	-
18.1 (OUTER SHEATH)	-
18.2 (OUTER SHEATH: Colour)	-
18.3 (Thicknes of outer sheath : average )	-
18.3 (Thicknes of outer sheath : minimum )	-
19.1 i) a) (Annealing test (for copper))	-
19.1 i) b) (Tensile test (for aluminium) - Before stranding )	-
19.1 i) b) (Tensile test (for aluminium) - After stranding )	-
19.1 i) c) (Wrapping test ( for aluminium))	-
19.1 i) d) (Resistance test - Main conductor )	-
19.1 i) d) (Resistance test - Neutral conductor )	-
19.1 iii) a) (Phyaical tests for insulation : Tensile Test)	-
19.1 iii) a) (Phyaical tests for insulation : Elongation )	-
19.1 iii) b) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
19.1 iii) b) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 iii) b) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
19.1 iii) d) (Phyaical tests for insulation : Hot set )	-
19.1 iii) d) (Phyaical tests for insulation : Permanent set )	-
19.1 iii) e) (Phyaical tests for insulation : Shrinkage )	-
19.1 iii) e) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
19.1 iii) f) (Insulation: Waterabsorption(gravimetric))	-
19.1 v) b) (Volume resistivity)	-
19.1 vi) a) (Physical tests for outer sheath : Tensile stregth )	-
19.1 vi) a) (Physical tests for outer sheath : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 iii) a) (Phyaical tests for insulation : Tensile Test)	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
19.1 vi) d) (Sheath : Hot deformation)	-
19.1 vi) e) (Loss of massIn air oven)	-
19.1 vi) f) (Sheath : Heat shock test)	-
19.1 vi) g) (Sheath : Thermalstability)	-
20.7 (High voltage test)	-
20.8 (Flammability test)	-
20.1 (Oxygen Index Test)	-
20.11 (Flame Retardance Test on Single Cables)	-
20.12 (Flame Retardance Test on Bunched Cables)	-
20.14 ( Test for Smoke Density)	-
20.15 (Temperature Index)	-
21.1 (IDENTIFICATION : Manufacturer's Identification)	-
21.2 (IDENTIFICATION : Cable Identification)	-
21.3 (IDENTIFICATION : Cable Code)	-

Partial

-
-

212

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Diameter, Ovality & Weight)	-
Cl 9 (UTM & HBW)	-
Cl 7 (Workmanship)	-
6.1, 6.2 (carbon)	-
6.1, 6.2 (sulphur)	-
6.1, 6.2 (silicon )	-
6.1, 6.2 (manganese)	-
6.1, 6.2 (phosphorus)	-

Partial

-
-

213

IS 1825 (1983)

Specification for aluminium alloy milk cans (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (a) Rated Capacity)	-
8 (b) Point of Capacity)	-
8 (c) Batch OR Code No.)	-
8 (d) BIS Mark)	-
8 (e) Manufacturer's Trade Mark )	-
2 (Capacity)	-
4 Fig. 1 (Dimensions & Shape)	-
4 Fig. 1 (A)	-
4 Fig. 1 (B)	-
4 Fig. 1 (C )	-
4 Fig. 1 (D)	-
4 Fig. 1 (E)	-
4 Fig. 1 (F)	-
4 Fig. 1 (G)	-
4 Fig. 1 (H)	-
4 Fig. 1 (BOTTOM BAND)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Drain Holes )	-
4 Fig. 1 (HANDLE )	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (LID)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Hole Dia 8 ,2 holes)	-
4 Fig. 1 (Hole Dia 12, 3 holes)	-
5 (a)Transport cans shall consist of a body, bottom band)	-
5 (lid and handles.)	-
5 (b)Minimum Thickness(in mm))	-
5 (i) Body and Neck)	-
5 (ii) Bottom)	-
5 (iii) Lid (Inner))	-
5 (iv) Lid (Outer))	-
5 (c) Mode of Shaping)	-
5 (i) If the thickness at shoulder is less than 2.5 mm a )	-
5 (reinforcement ring of 2 mm thickness shall be provided.)	-
5 (ii) Brinell Hardness 85 HB Min.)	-
5 (d) BOTTOM BAND- It shall be shrunk fit with a )	-
5 (proper locking arrangement on the body. This shall)	-
5 (be followed by brazing or welding all round.)	-
5 (e) HANDLES (as per Cl 5.6))	-
5 (f) SEALING LUG (as per Cl 5.7))	-
5 (g)Workmanship and Finish- All brazing or welding shall )	-
5 (be sound , free of porosity and shall be finished smooth .)	-
5 (h) Mass 6.5 Kg. Min.)	-
7 (i) Air Pressure Test (Cl 7.1))	-
7 (ii) Drop Test (Cl 7.2))	-
7 (iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-

Complete

-
-

214

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Sizes and Tolerances - IS 4224)	-
7.1 (Tensile Test - IS 1608(Pt -1))	-
4 (Freedom from defects , IS 4224)	-
7.2 (Reverse Bend Test--IS 1716)	-

Complete

-
-

215

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
16.13 (Test for Halogen Acid Gas Evolution)	-
3 (CONDUCTOR: MATERIALS)	-
4 (INSULATION : MATERIALS)	-
5.1 (FILLER AND INNER SHEATH)	-
5.2 (FILLER AND INNER SHEATH)	-
6 (ARMOURING)	-
7 (OUTER SHEATH)	-
8.1 (CONDUCTOR: CONSTRUCTION)	-
8.2 (PROTECTIVE BARRIER)	-
8.3 (SIZE OF NEUTRAL CONDUCTOR)	-
9.1 (Insulation Applied by extrusicn)	-
9.2 (Thickness of Insulation - Average)	-
9.3 (Thickness of Insulation - Minimum)	-
9.4 (Application of Insulation)	-
10.1 (Core Identification)	-
10.2 (Core Identification- Neutral)	-
10.3 (Core Identification by number )	-
10.4 (Core Identification by number - Neutral )	-
11 (LAVING UP OF CORES)	-
12.1 & 12.2 (Inner sheath : Application)	-
12.3 (Thickness of Inner Sheath)	-
13.1 (Armouring: Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (Armouring: Direction of Lay )	-
13.2 (Type of armour )	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (Armour: Joint)	-
13.5 (Armouring : Resistance Test)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (Outer Sheath : Application)	-
14.2 (Colour of outer sheath)	-
14.3 (Thickness of outer sheath - AVERAGE)	-
14.3 (Thickness of outer sheath - minimum)	-
15.1 a) i) (Annealing Test ( For copper wire ) )	-
15.1 a) ii) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) ii) (Tensile test (for aluminium) - After stranding )	-
15.1 a) iii) (Wrapping test (for aluminium))	-
15.1 a) iv) (Resistance test - Neutral conductor)	-
15.1 a) iv) (Resistance test - Main conductor)	-
15.1 a) iv) (Resistance test - Neutral conductor)	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 e) v) (Sheath : Hot deformation)	-
15.1 e) vi) (Sheath : Heat shock test)	-
15.1 e) vii) (Sheath : Thermalstability)	-
15.1 f) (INSULATION RESISTANCE TEST : Volume resistivity )	-
16.2 (HIGH VOLTAGE TEST )	-
16.3 (FLAMMABILITY TEST : Period of Burning )	-
16.2 (HIGH VOLTAGE TEST )	-
16.3 (FLAMMABILITY TEST : Period of Burning )	-
16.3 (FLAMMABILITY TEST : Unaffected length )	-
16.9 (Oxygen Index Test)	-
16.1 (Flame Retardance Test on Single Cables)	-
16.11 (Flame Retardance Test on Bunched Cables)	-
16.14 (Temperature Index)	-
17.1 (Manufacturer'. ldeadentificatioa)	-
17.2 (cable Indentification )	-
17.3 (cable Code )	-

Complete

-
-

216

IS 651 (2007)

Glazed stoneware pipes and fittings - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 7.4 (Acid Resistance Test)	-
Clause 7.5 (Alkali Resistance Test)	-
7.2 (Hydraulic Test)	-
7.3 (Absorption Test)	-
11.1-Table 1 ( Mean Thickness of Barrel and of Socket)	-
10.1-Table 1 (INTERNAL DIAMETER)	-
14-Table 1 (Internal Depth of Socket)	-
14-Table 2 (Excess Shoulder Measurment)	-
14-Table 3 (Length of Grooving of Spigot)	-
12.2 (STRAIGHTNESS OF BARRELS OR STRAIGHT AND TAPER PIPES-Length of Junction)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-Internal Diameter)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-angle)	-
13.1-Table 6 (Dimensions of One-Eighth Taper Bends-D)	-
17-Table 10 (Dimensions of Channel Interceptors-A)	-
17-Table 10 (Dimensions of Channel Interceptors-G)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-Type)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-A)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-G)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F')	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-E)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-D)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-Size)	-
14 (The interior of the sockets shall be conical, having a minimum taper)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-r)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-r)	-
17-Table 10 (Dimensions of Channel Interceptors-C)	-

Partial

-
-

217

IS 458 (2003)

Precast concrete pipes(With And Without Reinforcement) - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (a) Identification)	-
5.1.1 (b) Date of cast )	-
5.1.1 (c) Date of test )	-
5.1.1 (d) i) Curing-when received dry the specimen shall be kept in water for 24 hr)	-
5.1.1 (ii) weight)	-
5.1.1 (iv) Cross-sectional area ( in mm2))	-
5.1.1 (v) Max. Load ( in kN) )	-
5.1.1 (vi) Compressive strength, N/mm2 )	-
5.1.1 (vii) Fracture)	-
5.1.1 (viii) Individual variation of average )	-

Partial

-
-

218

IS 624 (2003)

Bicycles - Rims - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (FINISH)	-
3.2 (SHAPES AND DIMENSIONS)	-
9 (COMPRESSION TEST)	-
7 (chem) (FINISH)	-

Partial

-
-

219

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 5.1.2 (Weight)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.3 (Tensile Test On UTM)	-
3.1.1 (PHOSPHORUS)	-
3.1.1 (SULPHUR)	-
Cl. 7.5 (Ductility/ Reverse Bend Test)	-

Partial

-
-

220

IS 1729 (2002)

Cast iron/ductile iron drainage pipes and pipe fittings for over ground non-pressure pipeline socket and spigot series (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Tensile Strrngth - IS1608(Pt-1))	-
5.1 (Elongation - IS 1608(Pt-1))	-
5.4 (Hardness- IS 1500)	-
7 (Leakage Test - IS 1729)	-
8.2-Table 1 to 32 (Dimension, a)	-
8.2-Table 1 to 32 (Dimension, b)	-
8.2-Table 1 to 32 (Dimension, c)	-
8.2-Table 1 to 32 (Dimension, d)	-
8.2-Table 1 to 32 (Dimension, e)	-
8.2-Table 1 to 32 (Dimension, f)	-
8.2-Table 1 to 32 (Dimension, g)	-
8.2-Table 1 to 32 (Dimension, h)	-
8.2-Table 1 to 32 (Dimension, i)	-
8.2-Table 1 to 32 (Dimension, j)	-
8.2-Table 1 to 32 (Dimension, k)	-
8.2-Table 1 to 32 (Dimension, l)	-
8.2-Table 1 to 32 (Dimension, m)	-
8.2-Table 1 to 32 (Dimension, n)	-
8.2-Table 1 to 32 (Dimension, p)	-
8.2-Table 1 to 32 (Dimension, q)	-
8.2-Table 1 to 32 (Dimension, r)	-
8.2-Table 1 to 32 (Dimension, r1)	-
8.2-Table 1 to 32 (Dimension, r2)	-
8.2-Table 1 to 32 (Dimension, s)	-
8.2-Table 1 to 32 (Dimension, t)	-
11 (Coating Test at 65degree Celcius )	-
11 (Coating Test at 0degree Celcius )	-
5.3 (Casting Defects)	-

Complete

-
-

221

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-

Partial

-
-

222

IS 2255 (1977)

Specification for mild steel wire rod for the manufacture of machine screws (By Cold Heading Process) (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Sizes and tolernces)	-
8 (FREEDOM FROM DEFECTS)	-

Complete

-
-

223

IS 2266 (2019)

Steel wire ropes for general engineering purpose - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12 (a) Size)	-

Partial

-
-

224

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (S)	-
4 (P)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-
11 (a) Size)	-
11 (b) Construction)	-
11 (c) tensile designation)	-
11 (d) lay)	-
11 (e) coating)	-
11 (f) length)	-
11 ( g) mass)	-
11 (h) manufacturer's name or trade mark)	-
11 (i) lot number along with the order number)	-
11 (j) BIS Standards Mark)	-
5 (a) Grade)	-
5 (b) Tensile Grade)	-
6 (a) Lay)	-
6 (b) Construction)	-
7 (Freedom from defects)	-
9 (a) Tensile)	-
9 (b) Elongation)	-
9 (c) Galvanizing Test)	-
11 (a) Size)	-
11 (b) Construction)	-

Partial

-
-

225

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 3.1.1 (Sulphur)	-
Clause 3.1.1 (Phosphorus)	-
Cl 5 & 6 (Diameter)	-
Cl 7 (UTM)	-
Cl 4.1 (Workmanship)	-
Cl 8.3 (Bending To Both Side At 90°, Then Straight)	-
Clause 7.1 (Ultimate Tensile Stress)	-

Partial

-
-

226

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.2 (Diameter & Ovality)	-
Cl 6.2 (Weight)	-
Cl 8.2 (Bend test)	-
Cl 5.1 (Workmanship)	-
Cl 9.3 (Press)	-
Clause -4, 4.1 ( CARBON)	-
Clause -4, 4.1 (SULPHUR)	-
Clause -4, 4.1 (SILICON)	-
Clause -4, 4.1 (MANGANESE)	-
Clause -4, 4.1 (PHOSPHURS)	-
Clause -4, 4.1 (NITROGEN)	-
Cl 6.1 (Diameter)	-
Cl 8.1 (ultimate tensile stress, yield stress and percentage elongation)	-
Cl 8 (Physical Requirements)	-

Partial

-
-

227

IS 210 (2009)

Grey iron castings - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 (SIZE OF TEST BARS-Diameter)	-
13 (SIZE OF TEST BARS-Length)	-
15, Table 3 (TENSIL.E TEST- IS 1608 Part1 )	-
16, Table 3 (Hardness Test)	-
6 (Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-
6 (Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-
7.1 (WORKMANSHIP AND FINISH)	-
10.1 (FREEDOM FROM DEFECTS)	-
10.2 (FREEDOM FROM DEFECTS)	-

Partial

-
-

228

IS 3431 (1982)

Specification for steel for the manufacture of volute helical and laminated springs for automotive suspension (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8,Table 4 (Mechanical properties - IS 3431)	-
12 (Straightness)	-
13, Table 5&Table 6 (Dimensions and Tolerance)	-
10 (Freedom from defects)	-
Cl. 2.1, 5.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Partial

-
-

229

IS 1239 : Part 2 (2011)

Steel tubes, tubulars and other steel fittings - Specification: Part 2 steel pipe fittings (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Chemical Composition - Sulphur - Laddle Analysis IS 228)	-
7.1 (Chemical Composition - Phosphorus - Laddle Analysis IS 228)	-
8.1-Table 1 ( DIMENSIONS OF TUBULARS-Pieces )	-
8.1-Table 1 ( DIMENSIONS OF TUBULARS-Pieces-Approximate Standard Length(A) )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-A )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-B )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-C )	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-A)	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-B)	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-C)	-
8.3.2 (DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-
8.3.2 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-The face of the back nut angle)	-
8.4.1 -Table 4 (Bends and springs)	-
8.4.1 -Table 4 (Bends and springs-A)	-
8.4.1 -Table 4 (Bends and springs-B)	-
8.4.1 -Table 4 (Bends and springs-C)	-
8.4.1 -Table 4 (Bends and springs-D)	-
8.4.1 -Table 4 (Bends and springs-E)	-
8.5-Table 5 ( Return Bends-A)	-
8.5-Table 5 ( Return Bends-B)	-
8.6 -Table 6 (Sockets-A)	-
8.6 -Table 6 (Sockets-B)	-
8.6 -Table 6 (Maximum Inside Diameter of Internal Parallel Thread)	-
9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D )	-
9.1-Table 7 (Dimensions of Screwed Ends of Fittings-E )	-
9.1-Table 7 (Dimensions of Screwed Ends of Fittings-d )	-
9.1-Table 8 (Dimensions of Elbows, Tees and Crosses, Equal-A)	-
9.1-Table 9 (Dimensions of Elbows Reducing-A)	-
9.1-Table 9 (Dimensions of Elbows Reducing-B)	-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-A)	-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-B)	-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-A)	-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-B)	-
9.1-Table 12 (Dimensions of Tees (Increasing on the Branch)-A)	-
9.1-Table 12 (Dimensions of Tees (Increasing on the Branch)-B)	-
9.1-Table 13 ( Dimensions of Crosses, Reducing-A)	-
9.1-Table 13 ( Dimensions of Crosses, Reducing-B)	-
9.1-Table 14 ( Elbows, Tees and Crosses, Side Outlet, Equal-A)	-
9.1-Table 14 ( Elbows, Tees and Crosses, Side Outlet, Equal-B)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-A)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-B)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-Minimum Bore of Male End)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-Maximum Bore of Male End)	-
9.1-Table 16 ( Dimensions of Elbows, Equal, 135°-A)	-
9.1-Table 17 (Dimensions of Y-Pieces, Female, Equal-A)	-
9.1-Table 18 (Dimensions of Socket, Reducing-A)	-
9.1-Table 19 (Dimensions of Caps-A)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-S)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-H)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-D)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-K)	-
9.1-Table 21 (Dimensions of Elbows, Tees and Crosses, Male, Equal-A)	-
9.1-Table 22 (Dimensions of Y-Pieces and Angle Tees, Male, Equal-A )	-
9.1-Table 22 (Dimensions of Y-Pieces and Angle Tees, Male, Equal-B )	-
9.1-Table 23 ( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-A)	-
9.1-Table 23 ( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-B)	-
9.1-Table 24 (Dimensions of Socket Unions-A )	-
9.1-Table 25 (Dimensions of Pipe Unions-A)	-
9.1-Table 26 (Dimensions of Union Bends-A )	-
9.1-Table 26 (Dimensions of Union Bends-B )	-
9.1-Table 27 (Dimensions of Hexagon Bushes-L)	-
9.1-Table 27 (Dimensions of Hexagon Bushes-T)	-
9.1-Table 27 (Dimensions of Hexagon Bushes-A)	-
9.1-Table 27 (Dimensions of Hexagon Bushes-B)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-L)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-T)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-A)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-C)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-B)	-
11.1(a) (Internal hydraulic Pressure Test)	-
11.1(a) (Internal Air Pressure Test)	-
11.2.1 ( Drift Expanding Test)	-
11.2.2 (Taper Screw Plug Test)	-
14 (WORKMANSHIP)	-
13 and as per IS 4736 (MASS OF ZINC COATING)	-
13 and as per IS 4736 (UNIFORMITY OF ZINC COATING)	-

Complete

-
-

230

IS 208 (1996)

Door Handles - Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-
9 (MARKING)	-
9.1 (BIS Certification Marking)	-

Partial

-
-

231

IS 7226 (1974)

Specification for cold - Rolled medium, high carbon and low alloy steel strip for general engineering purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.1, Table 3 (i)TOLERANCE ON WIDTH)	-
9.1, Table 4 (ii)TOLERANCE ON THICKNESS)	-
5 (HARDNESS TEST)	-
4.1 Table 1 (Carbon- IS 228)	-
4.1 Table 1 (Manganese- IS 228)	-
4.1 Table 1 (Silicon- IS 228)	-
4.1 Table 1 (Sulphur- IS 228)	-
4.1 Table 1 (Phosphorous- IS 228)	-

Partial

-
-

232

IS 11722 (1986)

Specification for thin walled flexible quick coupling pipes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9 (Galvanizing ,IS 4736)	-
9 (Galvanizing ,IS 4736)	-
9 (Galvanizing ,IS 4736)	-
9 (Galvanizing ,IS 4736)	-
6 &7 ; Table 1 (Dimension & Tolerance)	-
8 (Length)	-
11, Table 3 (Angularity of Joint)	-
13.1 (Flattening Test,IS 2328)	-
13.2 (Tensile Test ,; IS 1608(P1))	-
4.1 (Pipe Manufacturing Process )	-
5,5.1 (Workmsnship &Finish)	-
9 (Galvanizing ,IS 4736)	-

Partial

-
-

233

IS 3195 (1992)

Steel for the manufacture of volute and helical springs (For Railway Rolling Stock) - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Hardness)	-
11 ( DIMENSIONS AND TOLERANCES)	-
10 (Freedom from defects)	-
Cl. 3, 6.1, 6.2 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Partial

-
-

234

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Tensile Test & Flattening Test)	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 9 (Pipe ends, Angle of bevel & Root Face )	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 12 (Bituminous Coating & Galvanizing )	-
Cl 14 (Workmanship)	-
5.2 (phosphorus)	-
5.2 (sulphur)	-

Complete

-
-

235

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (TYPES)	-
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-
6.1 (Manufacture- General)	-
6.2- Table 2,3,4,5 (Kunckles)	-
6.3 (Screw Holes)	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2 (Screw Holes)	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-
6.3.3 Fig-1 (Position of Holes)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Carbon - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Manganese - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Sulphur - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Phosphorous - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992) (Chemical composition - Silicon - IS 228 (optional))	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Carbon - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Silicon - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Manganese - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Sulphur - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Phosphorous - IS 228)	-

Partial

-
-

236

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
5.2.1 Table 1 (Particulars-Barrel Tower Bolts)	-
5.2.2 Table 2 (Particulars-Skeleton Tower Bolts)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-
6.1- Table 1 (Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-

Partial

-
-

237

IS 204 : Part 1 (1991)

Tower bolts - Specification: Part 1 ferrous metals (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G )	-
6.1- Table 1 (Dimension of Barrel tower bolts-Minimum No. of equally Spaced Screw holes in Barrel and Socket for wood screw no 6)	-
6.2- Table 2 (Dimension of Sami Barrel Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Bolt Plate or Socket-F 8.Dia of bore of Bolt Plate or socket G )	-
6.2- Table 2 (Dimension of Sami Barrel Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-
6.3- Table 3 (Dimension of Riveted or Spot Welded Tower Bolts- 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7. Length of Strap-E" 8.Thickness of Back Plate -F 9.Thickness of Socket or Upper Plate and Strap- F" 10.Dia of bore of Bolt Plate or socket- G 11. Length of Alternative Socket-H )	-
6.3- Table 3 (Dimension of Riveted or Spot Welded Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Staple -F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob-J)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 6)	-
8.1 (MARKING- .)	-
8.1.1, (MARKING- )	-

Partial

-
-

238

IS 4148 (1989)

Surgical rubber gloves - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5 (pH of Aqueous Extract )	-

Complete

-
-

239

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
Cl 8 (Workmanship)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

Complete

-
-

240

IS 1812 (1982)

Specification for carbon steel wire for the manufacture of wood screws (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 ( Tensile Test IS1608(P-1))	-
6.2 ( Bend Test )	-
6.3 ( Wrapping Test )	-
7 (. SIZE TOLERANCE)	-
8 ( FREEDOM FROM DEFECTS)	-
Cl. 5.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Complete

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Office Laboratory (NROL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- [email protected]

Scope List