BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List

Reset

366 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

241

IS 6902 (1973)

Specification for steel wire for spokes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4.1 (Carbon- IS 228)	-
Cl. 4.1 (Manganese- IS 228.)	-
Cl. 4.1 (Sulphur- IS 228.)	-
Cl. 4.1 (Phosphorus- IS 228.)	-
5.1 ( Tensile strength )	-
6.0 ( Bend Test )	-
7.0 (Freedom from defects )	-
8.0 (Wire diameter & Tolerances)	-

Complete

-
-

242

IS 8229 (1986)

Specification for oil - Well cement (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 - Table - 1 i (Magnesium Oxide (MgO) - Cl 4.8 of IS 4032:1985)	-
4.1 - Table - 1 ii (Sulphur Trioxide(SO3) - Cl 4.9 of IS 4032:1985)	-
4.1 - Table - 1 iii (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
4.1 - Table - 1 iv (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
4.1 - Table - 1 v (Tricalcium aluminate (3CaO.Al2O3) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 x (Tricalcium Silicate (3CaO.SiO2) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 xii (Total alkali content, expressed as Sodium Oxide (Na2O) equivalent - Cl 4.11 of IS 4032:1985)	-
4.1 - Table - 1 xix (Tetracalcium aluminoferrite (4CaO.Al2O3.Fe2O3) plus twice the tricalcium aluminate (3CaO.Al2O3) - Cl 4 of IS 4032:1985)	-
5.1 and Table 2 ii (Fineness IS : 4031:1988)	-
5.1 and Table 2 iii (Soundness, Autoclave expansion IS 4031:1988)	-
5.1 and Table 2 v a 1 (Compretsive Strenqth .With 8 hrs curing 38˚C at atmospheric pressure)	-
5.1 and Table 2 v a 2 (Compretsive Strenqth .With 8 hrs curing 60˚C at atmospheric pressure)	-
5.1 and Table 2 v c 1 (Compretsive Strenqth .With 24 hrs curing 38˚C at atmospheric pressure)	-

Partial

-
-

243

IS 4824 (2006)

Bead wire for tyres - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 & Table 3 (UTM)	-
Cl 8 (Torsion)	-
Cl 9 (Press)	-
Cl 10 (Straightness)	-
Cl 13 (Workmanship)	-
Cl 14 (Diameter)	-
Cl 15.1 (Workmanship)	-

Partial

-
-

244

IS 1783 : Part 2 (2014)

Drums large, fixed ends - Specification: Part 2 grade B drums (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
7 (Construction)	-
7.4 (Construction)	-
7.5 (Construction)	-
8 (Finish )	-

Partial

-
-

245

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Freedom from defects , IS 6911)	-
10.1,Table 4&Table 6 (Tensile Test - IS 1608(Pt -1))	-
10.2,Table 4&Table 5 (Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-
10.3 (Bend Test - IS 1599)	-
11,Table 7 (Erichsen cupping test-IS 10175)	-
17 (Dimension and tolerance)	-
Cl. 7.1 & 7.2 Table 1 (Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.12 (Corrosion Resistance- IS 10461(Part1))	-
Cl.12 (Corrosion Resistance- IS 10461(Part2))	-

Partial

-
-

246

IS 6603 (2001)

Stainless steel bars and flats - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Carbon -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Silicon- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Manganese- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Nickel -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Chromium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Phosphorus- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Others (Nitrogen)- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl.14.1 (Corrosion Resistance- IS 10461(Part1))	-
Cl.14.1 (Corrosion Resistance- IS 10461(Part2))	-
6 (Freedom from defects:)	-
9.1, Table 3 (0.2 Percent Proof Stress, MPa)	-
9.2, Table 3 (Tensile Strength, MPa)	-
9.3, Table 3 (Elongation ,Percent)	-
9.4, Table 3 (Annealed Hardness, HB-IS 1500: Pt 1)	-
9.5, Table 3 (Charpy Impact Test, J-IS 1499)	-
12 (Diameter, mm)	-
12 (Out of Round , mm)	-
12 (Length , mm)	-
12 (Variation in Straightness)	-

Partial

-
-

247

IS 4454 : Part 1 (2001)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-
7.1, 7.2 (carbon)	-
7.1, 7.2 (sulphur)	-
7.1, 7.2 (phosphorus)	-
7.1, 7.2 (manganese)	-
7.1, 7.2 (silicon )	-
7.1, 7.2 (copper)	-

Partial

-
-

248

IS 7092 : Part 2 (1987)

Specification for aluminium alloy tube for irrigation purposes: Part 2 extruded tube (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Workmanship & Finish)	-
Cl. 6.3 (Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-
Cl.6.2 (0.2 percent proof strength- IS 2657)	-
Cl.6.2 (Elongation on 50 mm gauge length- IS 2657)	-
Cl. 6.3 (Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-
Cl.7.1, Table 2 (Outside Diameter-)	-
Cl.7.1, Table 2 (Roundness or Ovality)	-
Cl.7.1, Table 2 (Wall Thickness)	-
Cl. 7.2 (Length)	-

Partial

-
-

249

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.1 (Workmanship)	-
Cl 5 & 6 (Diameter)	-
Cl 8.3 (Bending To Both Side At 90°, Then Straight)	-
Clause 3.1.1 (Sulphur)	-
Clause 3.1.1 (Phosphorus)	-
Cl 7 (UTM)	-

Complete

-
-

250

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Workmanship)	-
Cl 6.2 (Weight)	-
Cl 6.2 (Diameter & Ovality)	-
Cl 8.2 (Bend test)	-
Cl 9.3 (Press)	-
Clause -4, 4.1 ( CARBON)	-
Clause -4, 4.1 (MANGANESE)	-
Clause -4, 4.1 (SULPHUR)	-
Clause -4, 4.1 (PHOSPHURS)	-
Clause -4, 4.1 (SILICON)	-
Clause -4, 4.1 (NITROGEN)	-
Cl 6.2 (Diameter & Ovality)	-
Cl 9.3 (Press)	-

Partial

-
-

251

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Pertial

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (CONDUCTOR)	-
4.1.1 (CONDUCTOR)	-
5 (INSULATION)	-
6.1.1 (SCREENING : - Non-metallic — Semiconducting Compound)	-
6.1.2 (SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-
7 (FILLERS AND INNER SHEATH)	-
8.1 (ARMOURING)	-
8.2 (ARMOURING)	-
9 (OUTER SHEATH )	-
10.1 (CONDUCTOR)	-
10.2 (CONDUCTOR)	-
11 (CONDUCTOR SCREENING)	-
12.2 (INSULATION : Thickness of Insulation)	-
12.3 (INSULATION : Tolerance on Thickness of Insulation)	-
12.5 (INSULATION : Application of Insulation)	-
13.1 (INSULATION SCREENING)	-
13.2 (INSULATION SCREENING)	-
14.1 (CORE IDENTIFICATION)	-
14.1.1 (CORE IDENTIFICATION)	-
15.1 (LAVING UP OF CORES)	-
16.1 (INNER SHEATH (COMMON COVERING))	-
16.2 (INNER SHEATH (COMMON COVERING))	-
16.3 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
17.1 (ARMOURING : Application )	-
17.2 (ARMOURING : Type of armour )	-
17.3 (ARMOURING : Dimension )	-
17.4 (ARMOURING : Joints)	-
16.4 (ARMOURING : Resistance)	-
18.1 (OUTER SHEATH)	-
18.2 (OUTER SHEATH: Colour)	-
18.3 (Thicknes of outer sheath : average )	-
18.3 (Thicknes of outer sheath : minimum )	-
19.1 i) a) (Annealing test (for copper))	-
19.1 i) b) (Tensile test (for aluminium) - Before stranding )	-
19.1 i) b) (Tensile test (for aluminium) - After stranding )	-
19.1 i) c) (Wrapping test ( for aluminium))	-
19.1 i) d) (Resistance test - Main conductor )	-
19.1 i) d) (Resistance test - Neutral conductor )	-
19.1 v) b) (Volume resistivity)	-
19.1 vi) a) (Physical tests for outer sheath : Tensile stregth )	-
19.1 vi) a) (Physical tests for outer sheath : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
19.1 vi) d) (Sheath : Hot deformation)	-
19.1 vi) e) (Loss of massIn air oven)	-
19.1 vi) f) (Sheath : Heat shock test)	-
19.1 vi) g) (Sheath : Thermalstability)	-
20.8 (Flammability test)	-
21.1 (IDENTIFICATION : Manufacturer's Identification)	-
21.2 (IDENTIFICATION : Cable Identification)	-
21.3 (IDENTIFICATION : Cable Code)	-
12.4 (Eccentricity and Ovality)	-

Partial

-
-

252

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 5.1.2 (Weight)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.2 (Tensile Test On UTM)	-
Cl 6.3 (Tensile Test On UTM)	-

Partial

-
-

253

IS 6529 (1996)

Stainless steel blooms, billets and slabs for forging - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1,7.2,7.3 Table 1 (Carbon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Silicon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Manganese-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Nickel-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Chromium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Phosphorous-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Others(Nitrogen)-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
13 (Corrosion Resistance- IS 10461(Part1))	-
13 (Corrosion Resistance- IS 10461(Part2))	-
6 (Freedom from defects)	-
9 (Hardness)	-
10 (Dimensional Tolerances)	-

Partial

-
-

254

IS 17423 (2020)

Medical textiles – Coveralls for COVID 19 – Specification

Complete

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Manufacture - IS 17423)	-
4.1.1 (Manufacture - IS 17423)	-
4.2 (Manufacture - IS 17423)	-
4.3 (Manufacture - IS 17423)	-
4.4 (Manufacture - IS 17423)	-
4.4 (Manufacture - IS 17423)	-
4.5 (Manufacture - IS 17423)	-
4.6 (Manufacture - IS 17423)	-
5.1 (Workmanship and Finish - IS 17423)	-
5.1 (Workmanship and Finish - IS 17423)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric from body Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric from body Specimen 2)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric from body Specimen 3)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric at Seam Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric at Seam Specimen 2)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric at Seam Specimen 3)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover Fabric from body Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover Fabric from body Specimen 2)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover Fabric from body Specimen 3)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover of Seam Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover of Seam Specimen 3)	-
4.1.1 (Manufacture - IS 17423)	-
4.2 (Manufacture - IS 17423)	-
4.2 (Manufacture - IS 17423)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover of Seam Specimen 2)	-

Partial

-
-

255

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8 (Diameter, Ovality & Weight)	-
Cl 9 (UTM & HBW)	-
6.1, 6.2 (carbon)	-
6.1, 6.2 (silicon )	-
6.1, 6.2 (manganese)	-
6.1, 6.2 (sulphur)	-
6.1, 6.2 (phosphorus)	-
6.1, 6.2 (molybdenum)	-
6.1, 6.2 (copper)	-
6.1, 6.2 (cromium)	-
6.1, 6.2 (nickel)	-

Partial

-
-

256

IS 14494 (2019)

Elastomer insulated flexible cables for use in mines - Specification (First Revision)

Partial

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (CONDUCTOR)	-
5 (INSULATION)	-
5.1 (Power Cores)	-
5.2 (Pilot and Earth Cores)	-
6 (SEMI-CONDUCTING COMPOUND)	-
4 (CONDUCTOR)	-
5 (INSULATION)	-
5.1 (Power Cores)	-
5.2 (Pilot and Earth Cores)	-
6 (SEMI-CONDUCTING COMPOUND)	-
7.1 (TAPE : Proofed Tape)	-
7.2 (TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-
7.3 (TAPE )	-
8 (CENTRE)	-
9.1 (FILLERS)	-
9.2 (FILLERS)	-
10 (CRADLE SEPARATOR)	-
11.1 (ARMOUR)	-
11.2 a) (ARMOURING: Tensile Strength)	-
11.2 b) (ARMOURING: Elongation )	-
11.2 c) (ARMOURING: Torsion Test (For round wire ) )	-
11.2 d) (ARMOURING: Uniformity of zinc coating)	-
11.2 e) (ARMOURING: Mass of zinc coating )	-
12.1 (SHEATH : Inner Sheath)	-
12.2 (SHEATH : Outer Sheath)	-
13.1 (REINFORCEMENT MATERIAL : Tape)	-
13.2 (REINFORCEMENT MATERIAL : Cord/Yarns)	-
14.1 (CONSTRUCTION : CONDUCTOR)	-
15 (CONDUCTOR SCREENING)	-
16.1 (INSULATION)	-
16.2 (INSULATION : Thickness of Insulation)	-
16.3 (INSULATION : Tolerance on Insulation Thickness)	-
16.4 (INSULATION : Application of Insulation)	-
17.2 (INSULATION SCREEN)	-
18 (PROTECTIVE SCREEN)	-
20.1 (CORE IDENTIFICATION)	-
20.2 (Colour Scheme for Identification)	-
20.3 (Scheme for Identification by Numbering)	-
21.1 (LAYING UP OF CORES)	-
21.2 (LAYING UP OF CORES)	-
21.4 (LAYING UP OF CORES)	-
22.1 (INNER SHEATH)	-
22.2 (Thickness of Inner Sheath)	-
22.3 (INNER SHEATH)	-
23.1 (ARMOURING)	-
23.2 (ARMOURING)	-
23.4 (ARMOURING)	-
24.1 (OUTER SHEATH)	-
24.2 (Thickness of Outer Sheath)	-
24.3 (Tolerance on Thickness of Outer Sheath)	-
24.4 (OUTER SHEATH)	-
25.1 (CABLE CONSTRUCTION AND DIMENSIONS)	-
27.8 (Flammability Test)	-
28 (IDENTIFICATION)	-
29.1 (PACKING AND MARKING)	-
30 (BIS CERTIFICATION MARKING)	-

Partial

-
-

257

IS 6392 (2020)

Steel Pipes Flanges — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 Table 1 (Carbon- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Silicon- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Manganese- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Sulphur- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Phosphorous- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Nickel- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Chromium- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Copper- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Molybdenum- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Carbon- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Silicon- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Manganese- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Sulphur- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Phosphorous- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Nickel- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Chromium- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Copper- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Molybdenum- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Nitrogen Content-relevant parts of IS 228 or any other established instrumental/chemical method,)	-
6.1 (Dimension)	-
14 (Workmanship)	-

Partial

-
-

258

IS 1943 (1995)

Textiles – A-twill jute bags (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Sacking- IS 1943)	-
4.1 (Sacking- IS 1943)	-
4.2 (Seam -- IS 1943)	-
4.2 (Seam -- IS 1943)	-
4.2 (Seam -- IS 1943)	-
4.2 (Seam -- IS 570)	-
4.3 (Safety Stitches -IS 1943)	-
4.3 (Safety Stitches -IS 1943)	-
4.3 (Safety Stitches -IS 570)	-
4.4 (Hemming at the mouth IS 9113)	-
4.4 ( IS 570)	-
4.5 (Joined bag - IS 9113)	-
4.6 (Freedom from defects- IS 1943)	-
4.1,5.1,Table 1 (Dimension;Outside Length-IS 9113)	-
4.1,5.1,Table 1 (Dimension;Outside width-IS 9113)	-
4.1,5.1,Table 1 (Ends /dm -IS 1963)	-
4.1,5.1,Table 1 (Picks/dm -IS 1963)	-
4.1,5.1,Table 1 (Corrected Mass/Bag,g-IS 9113)	-
4.1,5.1,Table 1 (Average Breaking Strength in N -IS 1969 N)	-
4.1,5.1,Table 1 (Average breaking load of seam-IS 9030)	-
4.1,5.1,Table 1 (Moisture Regain, Percent-IS 9113)	-
4.1,5.1,Table 1 (Oil content, Percent-IS 2969)	-

Complete

-
-

259

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.7.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Depth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Width))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Thickness))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Weigth))	-
Cl. 10.1, 14.1, 18.1 (Straightness)	-
Cl. 10.4, Fig 2 (Concavity, X1)	-
Cl. 10.4, Fig 2 (Convexity, X2)	-
Cl. 10.6, Fig 4 (External Corner Radius)	-
Cl. 10.7, Fig 5 (Total twist, V)	-
Cl. 15.2, Table 3 (Tensile Strength- IS 1608)	-
Cl. 15.2, Table 3 (Yield Strength- IS 1608)	-
Cl. 15.2, Table 3 (Elongation- IS 1608)	-
Cl. 14.1 (Exact Length)	-
Cl. 10.5, Fig 3 (Squareness of side)	-

Partial

-
-

260

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
5.2.1 Table 1 (Particulars-Barrel Tower Bolts)	-
5.2.2 Table 2 (Particulars-Skeleton Tower Bolts)	-
6.1- Table 1 (Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-
6.1- Table 1 (Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-

Partial

-
-

261

IS 4454 : Part 4 (2001)

Steel wires for mechanical springs: Part 4 stainless steel wire (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

Partial

-
-

262

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-
6.1 (Manufacture- General)	-
6.2- Table 2,3,4,5 (Kunckles)	-
6.3 (Screw Holes)	-
6.3.3 Fig-1 (Position of Holes)	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989) (Chemical composition - Copper - IS 3685:1966)	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989) (Chemical composition - Lead - IS 3685:1966)	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989) (Chemical composition - Iron - IS 3685:1966)	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983) (Chemical composition - Zinc - IS 3685:1966)	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989) (Chemical composition - Zinc- IS 3685:1966)	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983) (Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983) (Chemical composition - Nickel - IS 3685:1966)	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983) (Chemical composition - Tin - IS 3685:1966)	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987) (Chemical composition - Tin - IS 4027:1967)	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987) (Chemical composition - Lead - IS 4027:1967)	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987) (Chemical composition - Copper - IS 4027:1967)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Carbon - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Silicon - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Manganese - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Nickel - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Chromium - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Molybdenum - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Sulphur - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Phosphorous - IS 228)	-

Partial

-
-

263

IS 4398 (1994)

Carbon - Chromium steel for the manufacture of balls, rollers and bearing races - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
14 ( Dimensional tolerances)	-

Partial

-
-

264

IS 9968 : Part 2 (2002)

Specification for elastomer - Insulated cables: Part 2 for working voltages from 3.3 kV up to and including 33 kV (First Revision)

Partial

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (CONDUCTORS: Cables for Fixed Installation)	-
4.2 (CONDUCTORS:Flexible Cables)	-
13.1 & 13.2 (CONSTRUCTION:CONDUCTORS-Cables for Fixed Installations/Flexible Cables)	-
13.3 (Earthing Conductor)	-
13.3.1 (Earthing Conductor)	-
13.4 (Separator Tape)	-
22.1 a)1) (Annealing test (for copper) - IS 10810: Part 1)	-
22.1 a)2) (Tensile test (for aluminium) -IS 10810: Part 2)	-
22.1 a)3) (Wrapping Test (for aluminium) - IS 10810: Part 3)	-
22.1 a)4) (Conductor resistance test)	-
22.1 a)5) (Persulphate test (tinned copper conductor)- IS 10810: Part 4)	-
5 (INSULATION)	-
7.1 (Proofed Tape)	-
7.2 (Polyethylene Terephthalate ( P E T P ) or Polypropylene Base Tape : Thickness)	-
7.3 (Tape )	-
8 (SCREENING)	-
9 (CENTRE AND FILLERS)	-
10 (ARMOUR)	-
11.1 (Inner Sheath)	-
11.2 (Outer Sheath)	-
12.1 (Tapes)	-
12.2 (Cords and Yarns)	-
14 (CONDUCTOR SCREENING)	-
15.1 (INSULATION : Application)	-
15.2 (Thickness of Insulation)	-
16.1 (INSULATION SCREENING : Application)	-
16.2 (INSULATION SCREENING : Parts )	-
16.3 (INSULATION SCREENING : Non Metallic Parts )	-
16.4 (INSULATION SCREENING : Metallic Parts )	-
17 (CORE IDENTIFICATION)	-
18.1 (LAYING UP OF CORES)	-
18.2 (LAYING UP OF CORES : Flexible cable)	-
18.3 (LAYING UP OF CORES : Binder Tape)	-
19.1 (Inner Sheath : Application)	-
19.2 (Thickness of Inner Sheath)	-
19.3 (Inner Sheath : proofed tape)	-
20.1 (ARMOURING: Application)	-
20.2 (Type of Armour)	-
20.2 1.2 (Direction of lay of armour)	-
20.2 1.3 (Joint in armour)	-
20.2.2 (Diameter of braiding)	-
20.2.2.1 (Braiding material)	-
20.3 (Substitution of the galvanized steel wires/formed)	-
22.1 b)1) (Test for Galvanized Steel Wires/Formed Wires 1) Dimensions -IS 10810: Part 36)	-
22.1 b)2)i) (Test for Galvanized Steel Wires/Formed Wires 2) Tensile Strentgh -IS 10810: Part 37)	-
22.1 b)2)ii) (Test for Galvanized Steel Wires/Formed Wires 2) Elongation at break -IS 10810: Part 37)	-
22.1 b)2)iii) (Test for Galvanized Steel Wires/Formed Wires 3) Torsion (for round wires only) -IS 10810: Part 38)	-
22.1 b)2)iv) (Test for Galvanized Steel Wires/Formed Wires 4) Winding (for strips only) -IS 10810: Part 39)	-
22.1 b)2)v) (Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Uniformity-IS 10810: Part 40)	-
22.1 b)2)vi) (Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Mass -IS 10810: Part 41)	-
22.1 b)2) vii) (Resistivity - IS 10810: Part 42)	-
22.1 c)2) (Physical Tests for Insulation : Tensile Strenth - IS 10810: Part 7)	-
22.1 c)2) (Physical Tests for Insulation : Elongation - IS 10810: Part 7)	-
22.1 c)3) (Physical Tests for Insulation ( Ageing in air oven): Tensile Strenth Variation - IS 10810: Part 12)	-
22.1 c)3) (Physical Tests for Insulation( Ageing in air oven) : Elongation variation - IS 10810: Part 12)	-
21.1 (OUTER SHEATH)	-
21.2 (Coulor of Outer sheath)	-
21.3 (Thickness of Outer Sheat: Average)	-
21.3 (Thickness of Outer Sheat: Minimum)	-
22.1 c)2) (Physical Tests for Sheath : Tensile Strenth - IS 10810: Part 7)	-
22.1 c)2) (Physical Tests for Sheath : Elongation - IS 10810: Part 7)	-
22.1 c)2) (Physical Tests for Sheath : Tensile Strenth - IS 10810: Part 7)	-
22.1 c)3) (Physical Tests for Sheath( Ageing in air oven) : Tensile Strenth variation - IS 10810: Part 12)	-
22.1 c)3) (Physical Tests for Sheath ( Ageing in air oven): Elongation variation - IS 10810: Part 12)	-
22.1 c)5) (Physical Tests for Insulation :Permanent set - IS 10810: Part 30)	-
22.1 c)5) (Physical Tests for Insulation :Hot set Elongation - IS 10810: Part 30)	-
22.1 c)5) (Physical Tests for Sheath :Permanent set - IS 10810: Part 30)	-
22.1 c)5) (Physical Tests for Sheath :Hot set Elongation - IS 10810: Part 30)	-
22.1 c)8) (Shrinkage : Insulation - IS 10810: Part 12)	-
22.1 c)8) (Shrinkage test- Crack observed : Insulation - IS 10810: Part 13)	-
22.1 c)9) (Hot deformation test : Insulation - IS 10810: Part 15)	-
22.1 c)9) (Hot deformation test : Sheath - IS 10810: Part 15)	-
22.1 c)10) (Loss of mass in air oven : Insulation - IS 10810: Part 10)	-
22.1 c)10) (Loss of mass in air oven : Sheath - IS 10810: Part 10)	-
22.1 c)12) (Thermal stability : Insulation - IS 10810: Part 60)	-
22.1 c)12) (Thermal stability : Sheath - IS 10810: Part 60)	-
22.1 d) (Insulation Resistance Test: Insulation resistance constant )	-
22.1 d) (Insulation Resistance Test: Volume resistivity )	-
22.1 k) (High Voltage Test for Four Hours)	-
22.1 n) (Flammability)	-
24.1 (Manufacturer's Identification)	-
24.2 (Voltage Identification)	-
24.3 (Cable Code)	-

Partial

-
-

265

IS 4397 (1999)

Cold - Rolled carbon steel strips for ball and roller bearing cages retainers - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
14.2, Table 5 (Length)	-
14.1, Table 3, Table 4 (Width)	-
14.1, Table 3, Table 4 (Thickness)	-
10 (CUPPING TEST)	-
9 (Hardness-IS 1500: Pt 1)	-

Partial

-
-

266

IS 5651 (1987)

Specification for steels for pneumatic tools (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table 1 (Carbon-IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Silicon-IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Manganese-IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Sulphur-IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Chromium-IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Phosphorous-IS 228 or any other established instrumental /Chemical method)	-
5.1.3 (Nickel-IS 228 or any other established instrumental /Chemical method)	-
5.1.3 (Copper-IS 228 or any other established instrumental /Chemical method)	-

Partial

-
-

267

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 7.1 & 7.2 Table 1 (Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Partial

-
-

268

IS 16186 (2014)

Textiles - Light weight jute sacking bags for packing 50 kg foodgrains - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (i)The bags shall be made from single piece of 2/1 twill weave jute sacking of uniform construction with warp running along the length of the bag. )	-
4.1 (ii) The mass per square meter of sacking used in the fabric of the bag 504 g.)	-
4.2.i) ( Type of stitches Herakle )	-
4.2.ii) ( Jute twine for stitches Two strands of 3-ply )	-
4.2.iii) ( Stitches/dm 10 ± 1 )	-
4.2.iv) (Tex of jute twine [ IS 9113 (Cl.5.1.2) ] 310 tex.X 3-ply )	-
4.3.i) ( Stitches/dm 10 ± 1 )	-
4.3.ii) (Tex of jute twine )	-
4.4 (Fabric shall be hemmed with jute yarn of 310 tex )	-
4.5, Annex A (GAW)	-
4.5, Annex A (Multiple broken/missing warp(end)-Two or more contiguous, regardless of length )	-
4.5, Annex A (Multiple broken weft(pick))	-
4.5, Annex A (Cut, hole, tear or patch-Two or more warp thread ruptured at adjoining points )	-
4.5, Annex A (Float-Fabric where warp and weft yarns escape)	-
4.5, Annex A (Gap stitching-Stitching missing)	-
4.5, Annex A (Corner gap-Hole formation due to improper stitching at the corner of the bag )	-
4.5, Annex A (Mildew-Staining of fabric due to fungal or bacterial growth visible to naked eye)	-
4.1 & 5.1, Table 1 (Outside Length, cm )	-
4.1 & 5.1, Table 1 (Outside Width, cm )	-
4.1 & 5.1, Table 1 (Ends /dm-IS 9113 (Cl.8.4.2))	-
4.1 & 5.1, Table 1 (Picks/dm-IS 9113 (Cl.8.4.2))	-
4.1 & 5.1, Table 1 (Corrected Mass/Bag,g-IS 9113 (Cl.8.5.2))	-
4.1 & 5.1, Table 1 (Warpway -IS 9113 (Cl.8.6.2))	-
4.1 & 5.1, Table 1 (Weftway-IS 9113 (Cl.8.6.2))	-
4.1 & 5.1, Table 1 (Moisture Regain, Percent-IS 9113 (Cl.8.2))	-
4.1 & 5.1, Table 1 (Oil content, Percent-IS 9113 (Cl.8.5.2))	-
4.1 & 5.1, Table 1 (Average Seam Strength in N-IS 9113 (Cl.8.7))	-

Complete

-
-

269

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
5 (Freedom from defects , IS 5517)	-
8,Table 6 (Hardness Test - IS 1500(Pt -1))	-
9, Table 5 (Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-
13.1&13.2&13.3 (Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-

Partial

-
-

270

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.1, Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
4 (Freedom from defects , IS 4224)	-
5 (Sizes and Tolerances - IS 4224)	-
7.1 (Tensile Test - IS 1608(Pt -1))	-
7.2 (Reverse Bend Test--IS 1716)	-

Partial

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List