BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List

Reset

366 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 5518 (1996)

Steels for die blocks for drop forging - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Dimensions (Type 2 C Drums Figure 2))	-

Partial

-
-

IS 6623 (2004)

High Strength Structural Nuts

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 Table-1 (Dimensions- d)	-
4.1 Table-1 (Dimensions- p)	-
4.1 Table-1 (Dimensions- da)	-
4.1 Table-1 (Dimensions- dw)	-
4.1 Table-1 (Dimensions- e)	-
4.1 Table-1 (Dimensions- m)	-
4.1 Table-1 (Dimensions- m'')	-
4.1 Table-1 (Dimensions- c)	-
4.1 Table-1 (Dimensions- s)	-
5.1 Table-2 (Rockwell Hardness)	-
5.1 Table-2 (Proof Load Tcst)	-

Partial

-
-

IS 1395 (1982)

Specification for low and medium alloy steel covered electrodes for manual metal arc welding (Third Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Size and tolerances)	-
6.1 ,6.2 (General requirement)	-
6.3.1, 6.3.2 (Covering)	-
10.1.5 (Moisture test requirement)	-
10.1.2 (Tensile test and ductility)	-

Partial

-
-

IS 4759 (1996)

Hot - Dip zinc coatings on structural steel and other allied products - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 Table 1, 9.2, 9.2.1 ,9.2.2 (Msaa of Zinc Coating - IS 4759 IS 6745 IS 3203 IS 6012 )	-
9.3 (Uniformity of Zinc Coating - IS 4759 IS 2633 )	-

Partial

-
-

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.3 (Table 1) (b) 6 mm and above)	-

Partial

-
-

IS 5509 (2000)

Fire retardant plywood - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 (dimensions)	-
9 (WORKMANSHIP AND FINISH)	-
12.2 (Moisture content )	-
12.4 (Static Bending Strength as per BWR grade of IS 303 :)	-
12.4 (Glue adhesion (water resistance ))	-

Partial

-
-

IS 13258 (2014)

Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gas - Requirements for inspection and reconditioning of used lpg cylinders (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 a (Physical Defects in the Cylinder Wall: Bulge, dent, cut or gouge, intersecting cut or gauge, intersecting cut or gouge etc)	-
6.1 b (Corrosion Defects in the Cylinder Wall)	-
6.1 c (Other defects)	-
9 (Replacement detachables)	-
10.4 (Tareweight verification)	-

Partial

-
-

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-
6 (a) Lay)	-
7 (Freedom from defects)	-

Partial

-
-

IS 8498 (2013)

Temephos, emulsifiable concentrate (EC) - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3.2 (Acidity (as H2SO4), )	-

Partial

-
-

IS 3502 (2009)

Steel chequered plates (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 5 (Workmanship)	-
4.1 (Grade E 250A of IS 2062.)	-

Partial

-
-

IS 266 (1993)

Sulphuric acid - Specification (Third Revision)

Technical grade only

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.2 (Description)	-
4.2 Table-1(iii) (Iron (as Fe),)	-
4.2&3 Table-1(i) (Total Acidity (as H2So4),)	-

Partial

-
-

IS 1993 (2018)

Cold - Reduced tinmill products - Electrolytic tinplate (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9.2 (Hardness requirement )	-
Cl 9.3 (Tensile requirement )	-
Cl 10.2.1 (Coils)	-
Cl 10.2.2 (Coils)	-
Cl 10.3.1 (Sheet)	-
Cl 10.3.2 (Sheet)	-
Cl 10.3.2.1 (Sheet)	-
Cl 10.3.2.3 (Sheet)	-
Annex-C (Carbon )	-
Annex-C (Sulphur)	-
Annex-C (Phosphorus)	-
Annex-C (Manganese)	-
Annex-C (Nitrogen)	-
Annex-C (Chromium)	-
Annex-C (Molybdenum)	-
Annex-C (Copper)	-
Annex-C (Nickel)	-
Cl 8 (Tin Coating mass )	-

Partial

-
-

IS 10701 (2012)

Structural plywood - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.3 (Glue Shear strength in dry state)	-
11.4.1 (Resistance to Water)	-
11.4.2 (Resistance to Water)	-
11.5 (Resistance to Micro-organisms)	-
11.6 (Tensile Strength)	-
11.8 (Wet Bending Strength)	-
Clause 11.2 (Moisture content)	-

Partial

-
-

IS 5872 (1990)

Cold rolled steel strips (Box Strappings) - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (UTM)	-
Cl 7 (Bending To Both Side At 90°, Then Straight)	-
Cl 9 (Workmanship)	-
Cl 10 (Width & Thickness)	-
Cl 11 (Workmanship)	-
Cl. 6 Table 3 (Elongation at 50 mm gauge length)	-

Partial

-
-

IS 3954 (1991)

Hot Rolled Steel Channel Sections for General Engineering Purposes - Dimensions

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4, 6.1, Table 1 (CHG 16, Mass)	-
4, 6.1, Table 1 (CHG 16, Depth of channel)	-
4, 6.1, Table 1 (CHG 16, Width of flange)	-
4, 6.1, Table 1 (CHG 16, Thickness of web)	-
4, 6.1, Table 1 (CHG 16, Thickness of flange)	-
4, 6.1, Table 1 (CHG 16, Slope of flange)	-
4, 6.1, Table 1 (CHG 16, Radius at root)	-
4, 6.1, Table 1 (CHG 16, Radius at toe)	-
4, 6.1, Table 1 (CHG 20, Mass)	-
4, 6.1, Table 1 (CHG 20, Depth of channel)	-
4, 6.1, Table 1 (CHG 20, Width of flange)	-
4, 6.1, Table 1 (CHG 20, Thickness of web)	-
4, 6.1, Table 1 (CHG 20, Thickness of flange)	-
4, 6.1, Table 1 (CHG 20, Slope of flange)	-
4, 6.1, Table 1 (CHG 16, Radius at root)	-
4, 6.1, Table 1 (CHG 20, Radius at toe)	-
4, 6.1, Table 1 (CHG 40, Mass)	-
4, 6.1, Table 1 (CHG 40, Depth of channel)	-
4, 6.1, Table 1 (CHG 40, Width of flange)	-
4, 6.1, Table 1 (CHG 40, Thickness of web)	-
4, 6.1, Table 1 (CHG 40, Thickness of flange)	-
4, 6.1, Table 1 (CHG 40, Slope of flange)	-
4, 6.1, Table 1 (CHG 40, Radius at root)	-
4, 6.1, Table 1 (CHG 40, Radius at toe)	-

Complete

-
-

IS 3818 (1992)

Continuous (Piano) hinges -Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4-Fig 1 (DIMENSIONS AND TOLERANCES-Nominal Size)	-
4-Fig 1 (DIMENSIONS AND TOLERANCES-B)	-
4-Fig 1 (DIMENSIONS AND TOLERANCES-C)	-
4-Fig 1 (DIMENSIONS AND TOLERANCES-D)	-
4-Fig 1 (DIMENSIONS AND TOLERANCES-T)	-
4-Fig 1 (DIMENSIONS AND TOLERANCES-CSK Screw No.)	-
4-Fig 1 (DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-
4-Fig 3 (DIMENSIONS AND TOLERANCES-B)	-
4-Fig 3 (DIMENSIONS AND TOLERANCES-B1)	-
4-Fig 3 (DIMENSIONS AND TOLERANCES-B2)	-
4-Fig 3 (DIMENSIONS AND TOLERANCES-C)	-
4-Fig 3 (DIMENSIONS AND TOLERANCES-D)	-
4-Fig 3 (DIMENSIONS AND TOLERANCES-T)	-
4-Fig 3 (DIMENSIONS AND TOLERANCES-CSK Screw No.)	-

Complete

-
-

IS 3735 (1996)

Canvas Shoes, Rubber Sole

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

IS 3196 : Part 4 (2001)

Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gases - Specification: Part 4 cylinders for toxic and corrosive gases

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

IS 2566 (1993)

Textiles – B-twill jute bags for packing foodgrains – Specification (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 9873 : Part 3 (2017)

Safety of toys: Part 3 migration of certain elements (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 - Table 1 (Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-

Partial

-
-

IS 7285 : Part 2 (2017)

Refillable seamless steel gas cylinders - Specification: Part 2 quenched and tempered steel cylinders with tensile strength less than 1 100 mpa (112 Kgf/mm²) (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.7 (Foot Rings)	-
6.8 (Neck Rings)	-
7.3 (Surface Defects)	-
7.5 (Out-of-Roundness)	-
7.6 (Mean Diameter)	-
7.7 (Straightness)	-
7.8 (see Fig. 5) (Verticality)	-
7.9 (Stability)	-
7.11 a) (For cylinders of water capacity up to and including 20 litres = )	-
7.11 b) (For cylinders of water capacity exceeding 20 litres =)	-
10.1.3 a) i) ( Tensile strength (Rg) )	-
10.1.3 a) ii) ( Yield strength (Re))	-
10.1.3 a) & 10.2.1 a) (Elongation percent Min on gauge length = 5.65 √ So)	-
10.3.1 &10.3.2Table 4 (Impact Test- )	-
10.4.1 Table 5 ,FIG. 9 (Bend Test)	-

Partial

-
-

IS 2039 : Part 1 to 3 (1991)

Steel tubes for bicycle and cycle rickshaws - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1 (Workmanship)	-
Cl. 6.2 (Fin Height)	-
Cl. 6.3 (Straightness)	-
Cl. 8.1 (Tensile Strength)	-
Cl. 8.1 (Yield Strength)	-
Cl. 8.1 (Elongation)	-
Cl. 9 (Diameter)	-
Cl. 9 (Thickness)	-
Cl. 3.2.1, Table 4 (Yield Stress)	-
Cl. 3.2.1, Table 4 (UTS)	-
Cl. 3.2.1, Table 4 (Elongation)	-
Cl. 4.2.1 (Diameter)	-
Cl. 9 (Thickness)	-
Cl. 4.2.3 (Length)	-
Cl. 4.2.1, Table 7 (Yield Stress)	-
Cl. 4.2.1, Table 7 (UTS)	-
Cl. 5.2.1, Table 10 (Diameter)	-
Cl. 5.2.2 (Mean Thickness)	-
Cl. 5.2.3, Table 6 (Length)	-

Complete

-
-

IS 2191 : Part 2 (1983)

Specification for wooden flush door shutiers (Cellular And Hollow Core Type): Part 2 particle board and hardboard pace panels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3 (Table-2) (Size- Height)	-
Cl. 3 (Table-2) (Size- Width)	-
Cl. 3.2 (Nominal thickness of shutters)	-
Cl. 7 (WORKMANSHIP AND FINISH)	-
Cl. 8.1 (End immersion Test)	-
Cl. 8.2 (Knife Test)	-
Cl. 8.3 (Adhesion Test)	-

Partial

-
-

IS 2191 : Part 1 (1983)

Specification for wooden flush door shuiters (Cellular And Hollow Core Type): Part 1 plywood face panels (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4 (Table-2) (Size- Height)	-
Cl. 4 (Table-2) (Size- Width)	-
Cl. 4.2 (Nominal thickness of shutters)	-
Cl. 5.1 (Timber)	-
Cl. 5.2 (Plywood)	-
Cl. 5.3 (Cross-Bands)	-
Cl. 5.4 (Face Veneers)	-
Cl. 5.6 (Adhesive)	-
Cl. 5.7 (Particle Board)	-
Cl. 8 (WORKMANSHIP AND FINISH)	-
Cl. 9.1 (End immersion Test)	-
Cl. 9.2 (Knife Test)	-
Cl. 9.3 (Adhesion Test)	-

Partial

-
-

IS 21 (1992)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (0.2 Percent Proof Stress)	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W') (0.2 Percent Proof Stress)	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3') (0.2 Percent Proof Stress)	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2') (0.2 Percent Proof Stress)	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1') (0.2 Percent Proof Stress)	-

Partial

-
-

IS 4368 (1967)

Specification for alloy steel billets, blooms and slabs for forging for general engineering purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Diameter, Ovality & Weight)	-
Cl 11 (Hardness & Tensile Test)	-

Partial

-
-

IS 7285 : Part 1 (2018)

Refillable seamless steel gas cylinders - Specification: Part 1 normalized steel cylinders (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.7 (Foot Rings)	-
6.8.1 (Neck Rings)	-
7.3 (Surface Defects)	-
7.4 (Out-of-Roundness)	-
7.5 (Mean Diameter)	-
7.6 (Straightness)	-
7.7 (see Fig. 3) (Verticality)	-
7.8 (Stability)	-
7.10 a) (For cylinders of water capacity up to and including 20 litres = )	-
7.10 b) (For cylinders of water capacity exceeding 20 litres =)	-
7.11 (Neck Thread)	-
10.1.3 a) & Clause 5.4 Table 3, i) ( Tensile strength (Rg) )	-
10.1.3 a) & Clause 5.4 Table 3, ii) ( Yield strength (Re))	-
10.1.3 a) & Clause 5.4 Table 3, iii) (Elongation percent Min on gauge length = 5.65 √ So)	-
Clauses 6.8 and 10.3.1,Table 4 iii), Sr.no.3 (Impact Test-Cylinder Diameter Dm >140 mm i) Direction- Transverse: ii) Test temperature, in °C –20)	-
Clauses 6.8 and 10.3.1,Table 4 iii), Sr.no.4 (Impact Test-Cylinder Diameter Dm ≤140 mmi) Direction-Longitudinal ii) Test temperature, in °C –20)	-
11.3 (Hardness Test)	-

Partial

-
-

IS 13095 (2020)

Butterfly Valves for General Purposes ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (VALVE END CONNECTIONS)	-
5.0 (SERVICE APPLICATIONS)	-
6.0 ( NOMINAL SIZES )	-
7.0 (NOMINAL PRESSURES)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck- r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -d2 )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck-r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Pipe O.D.- d1)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling - Nos.)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange -D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange - b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling - Nos.)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -k)	-
9.1.1 ( Double Flanged Body Ends)	-
9.2.2 (Wafer Body Ends)	-
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-
11.0 (Bodies)	-
12.0 (DISC AND SHAFT)	-
13.0 (SEATING AND LININGS)	-
14.2 (BEARINGS)	-
14.3 (BEARINGS)	-
16.0 (OPERATION)	-

Partial

-
-

IS 11951 (2009)

PUMPSET FOR DESERT COOLERS - SPECIFICATION ( First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9 (Marking)	-
4.1 (Dimensions and ratings)	-

Partial

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List