BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List

Reset

366 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 410 (1977)

Specification for cold rolled brass sheet, strip and foil (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 Table-1 (Cu)	-
6.1 Table-1 (Pb)	-
6.1 Table-1 (Fe)	-
6.1 Table-1 (Zn)	-
4.0 (Freedom from defects)	-
7.1.1 (Tensile Test)	-
Table-2 (Vickers Hardness)	-
Table-2 (Transverse Bend)	-
Table-2 (Longitudinal Bend)	-
Table-2 (Thickness)	-

Partial

-
-

IS 4882 (1979)

Specification for low carbon steel wire for rivets for use in bearing industry (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1,4.1.1,5.1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Phosphorus- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Nitrogen- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

Partial

-
-

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 10840 (1994)

Blow moulded hdpe containers for packing of vanaspati - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3 (Capacity)	-
4.4 (Mass)	-
4.5 (Shape and Dimensions)	-
4.6 (Wall Thickness)	-
4.7.1 (Closure Leakage test)	-
4.7.2 (Drop impact test)	-
4.7.3 (Stacking test)	-
4.7.4 (Handle Pull Test)	-
4.7.5 (Ink adhesion for printed containers)	-
4.7.6 (Product Resistance of printed containers)	-
4.7.7 (Migration test)	-

Complete

-
-

IS 10632 : Part 2 (1983)

Specification for non magnetic stainless steels for electrical applications: Part 2 specific requirements for binding wires

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

IS 2098 (1997)

Asbestos cement building boards - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 7.1 Table -1 (Cl. 7.1 ,Table-1 (Length))	-
Cl. 7.1 Table -1 (Cl. 7.1 , Table-1 (Width))	-
Cl. 7.2 Table -1 (Cl. 7.1 , Table-1 (Thickness))	-
8.3 Table 1 & 7.1 (TESTS-Measurement of Thickness )	-
8.4 (TESTS-Water Absorption Test )	-

Partial

-
-

IS 617 (1994)

Cast aluminium and its alloys - Ingots and castings for general engineering purposes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6, Table 2. (MECHANICAL PROPERTIES OF CASTINGS)	-
6.2 (Hardness)	-
9 (TOLERANCES ON DIMENSIONS OF CASTINGS)	-

Partial

-
-

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.1 (The tubing made out of this material shall be green in colour )	-
Cl.4.2 (The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-
Cl4.3.1 (The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-
Cl4.3.2 (it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-
Cl.4.6 (Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-
Cl.4.7 (Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-

Partial

-
-

IS 916 (2000)

Square tins for solid products - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Capacity)	-
4.2 (Dimension and Tolerances)	-
5.1 (Air-Pressure Test)	-

Partial

-
-

100

IS 5312 : Part 1 (2004)

Swing Check Type Reflux (Non-Return] Valves for Water Works Purposes - Part 1 : Single-Door Pattern

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2 (Manufacture Dimensions Table 2 )	-
6.9 (Manufacture )	-

Partial

-
-

101

IS 1879 (2010)

Malleable cast iron pipe fittings - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (Type of Fittings - IS 1879)	-
5.1.2 (Size designation - IS 1879)	-
5.1.2.1 (Equal fitting - IS 1879)	-
5.1.2.2 (Unequal fitting -IS 1879)	-
5.1.3 (Right and Left hand thread - IS 1879)	-
5.1.1 (Code Number -IS 1879)	-
6.1 (Tensile Strength - IS 14329)	-
6.1 (Elongation - Is 14329)	-
7.2- Table 2 (Wall thickness of fittings - IS 1879)	-
7.5 - Table 2 (Projection of Rainforcement - IS 1879)	-
7.5 - Table 3 (Width of Rainforcement - IS 1879)	-
7.1 - Table 4 to Table 27 (a - IS 1879)	-
7.1 - Table 4 to Table 27 (b - IS 1879)	-
7.1 - Table 4 to Table 27 (c- IS 1879)	-
7.1 - Table 4 to Table 27 (d- IS 1879)	-
7.1 - Table 28 (d -IS 1879)	-
7.1 - Table 28 (D - IS 1879)	-
9 (Freedom from defects )	-
10.i) (Mass of Galvanized coating )	-
10.ii) ( Uniformity of Galvanized coating-IS 2633)	-
10.iii) (Adhesion of Galvanized coating IS 2629)	-
10.iv) (Freedom from defects IS 4759)	-

Partial

-
-

102

IS 177 (1989)

Cotton drills – Specification (fourth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 / 3.1 (MANUFACTURE / Yarn)	-
3.2 (Cloth)	-
3.2.1 (Cloth)	-
3.2.2 (Cloth)	-
3.2.3 (Cloth)	-
4/ 4.1 table-1 (REQUIREMENTS)	-

Partial

-
-

103

IS 446 (2017)

Rubber hoses, textile - Reinforced, for compressed air - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Materials and construction)	-
6, Dimensions (Concentricity)	-
6, Dimensions (Internal Diameter)	-
Cl 6.3 (Tolerance on length)	-
6, Dimensions (Thickness of Cover of Type 3)	-
6, Dimensions (Thickness of Cover of Type 2)	-
6, Dimensions (Thickness of Cover of Type 1)	-
6, Dimensions (Thickness of Lining of Type 3)	-
6, Dimensions (Thickness of Lining of Type 2)	-
6, Dimensions (Thickness of Lining of Type 1)	-
7.1, Table 2 (Tensile Strength of Cover)	-
7.1, Table 2 (Elongation at Break of Cover of all types)	-
7.1, Table 2 (Tensile Strength of Lining)	-
7.1, Table 2 (Elongation at Break of Lining of all types)	-
7.1, Table 2 (Accelerated Ageing for all types: Change in Tensile Strength of Cover of its original value)	-
7.1, Table 2 (Accelerated Ageing for all types: Change in Elongation of Cover of its original value)	-
7.1, Table 2 (Accelerated Ageing for all types: Change in Tensile Strength of Lining of its original value)	-
7.1, Table 2 (Accelerated Ageing for all types: Change in Elongation of Lining of its original value)	-
7.1, Table 2 (Resistance to Liquid , Increase in Volume (Class B only)-Lining)	-

Partial

-
-

104

IS 4605 (2020)

Crepe Bandage - Specification ( Second Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.5 (Breaking Load)	-
8.3 ( Elasticity)	-
8.2 ( Weight per Unit Area)	-
8.1 ( Threads per Stated Length 1)Ends)	-
8.1 ( Threads per Stated Length 2)Ends)	-
5.2 (The selvedge )	-
4.0 ( DIMENSIONS 1)Width (cm) (Unstretched))	-
Clause.8.7 (Ether Soluble Substances)	-
Clause.8.6 (Water Soluble Substances)	-
Clause.8.4 (Chemical Neutrality)	-

Partial

-
-

105

IS 9738 (2003)

Polyethylene bags for general purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Classification)	-
5.0 (Structure & Shape)	-
7.2 (Length)	-
7.2,Table 6 (Width)	-
7.3 (Thickness)	-
8.1 (Appearance)	-
8.1.1 (Printing Bags)	-
8.2 (Water Leak Test)	-
8.3 (Printing Ink Adhesion Test)	-
8.4 (Drop Test)	-

Complete

-
-

106

IS 2041 (2009)

Steel plates for pressure vessels used at moderate and low temperature - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Workmanship)	-
Cl 10 (Length, Width & Thickness)	-
Cl 12.1 (UTM)	-
Cl 12.2 (Press)	-
Table 1,Cl.7.1 (Grade:- R220, R260,R 275,R355,H 235,H265, H295,H355) (Carbon-IS 228)	-
Table 1,Cl.7.1 (Grade:- R220, R260,R 275,R355,H 235,H265, H295,H355) (Silicon-IS 228)	-
Table 1,Cl.7.1 (Grade:- R220, R260,R 275,R355,H 235,H265, H295,H355) (Manganese-IS228)	-
Table 1,Cl.7.1 (Grade:- R220, R260,R 275,R355,H 235,H265, H295,H355) (Phosphorous-IS 228)	-
Table 1,Cl.7.1 (Grade:- R220, R260,R 275,R355,H 235,H265, H295,H355) (Sulphur-IS 228)	-
Table 1,Cl.7.1 (Grade:- R 275,R355,H 235,H265, H295,H355) (Molybdenum-IS 228)	-
Table 1,Cl.7.1 (Grade:- R220, R260,R 275,R355,H 235,H265, H295,H355) (Nitrogen- IS 228)	-
Table 1,Cl.7.1 (Grade:- R 275,R355,H 235,H265, H295,H355) (Chromium-IS 228)	-
Table 1,Cl.7.1 (Grade:- R 275,R355,H 235,H265, H295,H355) (Copper-IS 228)	-
Table 1,Cl.7.1 (Grade:- R 275,R355,H 235,H265, H295,H355) (Nickel-IS 228)	-

Partial

-
-

107

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Classification - IS 444)	-
5 (Lining - IS 444)	-
5 (Reinforcement - IS 444)	-
5 (Cover - IS 444)	-
5 (Lining and Cover - IS 444)	-
6.1- Table 1 (Internal diameters - ISO 4671)	-
6.2 (Concentricity - ISO 4671)	-
6.3 (Length -IS 4671)	-
6.4 ( thickness of the lining plus cover - ISO 4671)	-
6.4 (If the cover is fluted, the depth of the flutes - ISO 4671)	-
7.1 - Table 2 ( tensile strength of Lining - ISO 37 )	-
7.1 - Table 2 ( tensile strength of Cover - ISO 37 )	-
7.1 - Table 2 (elongation at break of Lining - ISO 37)	-
7.1 - Table 2 (elongation at break of Cover - ISO 37)	-
7.1 - Table 2 (Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-
7.1 - Table 2 (Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-
7.1 - Table 2 (Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-
7.1 - Table 2 (Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-

Partial

-
-

108

IS 5135 : Part 2 (1994)

Specification for hand rotary duster: Part 2 shoulder mounted type (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (Types)	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.3 (DIMENSIONS & TOLERANCES )	-
7.4 (DIMENSIONS & TOLERANCES )	-
7.4 (DIMENSIONS & TOLERANCES )	-
8.1 (WORKMANSHIP AND FINISH )	-
8.3 (WORKMANSHIP AND FINISH )	-
10.1.1 (MOISTURE CONTENT)	-
10.1.2, 10.1.2.1 (Table-1) (GLUE ADHESION IN DRY STATE)	-
10.1.2, 10.1.2.2 (GLUE ADHESION IN DRY STATE)	-
10.1.3, 10.1.3.1.1 (Table-1) (RESISTANCE TO WATER TEST)	-
10.1.3, 10.1.3.1.2 (RESISTANCE TO WATER TEST)	-
10.1.4 (RESISTANCE TO WATER TEST)	-
10.1.5 (MYCOLOGICAL TEST )	-
10.1.5, 10.1.5.1 (Table-1) (MYCOLOGICAL TEST )	-
10.1.5.2 (MYCOLOGICAL TEST )	-
10.1.6 (TENSILE STRENGTH)	-
10.1.7 (Table-2) (STATIC BENDING STRENGTH)	-
10.1.7 (Table-2) (STATIC BENDING STRENGTH)	-
10.1.7 (Table-2) (STATIC BENDING STRENGTH)	-
10.1.7 (Table-2) (STATIC BENDING STRENGTH)	-
10.1.8 (Table-3) (WET BENDING STRENGTH)	-
10.1.8 (Table-3) (WET BENDING STRENGTH)	-
10.1.8 (Table-3) (WET BENDING STRENGTH)	-

Partial

-
-

109

IS 8035 (1999)

Handpump - Shallow well - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Visual Tests)	-
6.2 (Dimensional and Other Tests)	-
6.3.1 (Routine Test)	-

Partial

-
-

110

IS 15500 : Part 1 to 8 (2004)

Deepwell handpumps, components and special tools - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2/2.3,(Refer fig 4.2 of Part4) (Dimensions of FIG. 4,2 HEAD— EWDP)	-
2/2.3,(Refer fig 4.3A of Part4) (Dimensions of Fig 4.3A Side Plate)	-
2/2.3,(Refer fig 4.3B of Part4) (Dimensions of Fig 4.3B Head Flange)	-
2/2.3,(Refer fig 4.3C of Part4) (Dimensions of Fig 4.3C Back Plate —Standard (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3D of Part4) (Dimensions of Fig 4.3D Bracket — Standard (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3E of Part4) (Dimensions of Fig 4.3E Back Plate — EDWP)	-
2/2.3,(Refer fig 4.3F of Part4) (Dimensions of Fig 4.3F Bracket — EDWP)	-
2/2.3,(Refer fig 4.3G of Part4) (Dimensions of Fig 4.3G Axle Bust — Right)	-
2/2.3,(Refer fig 4.3H of Part4) (Dimensions of Fig 4.3H Axle Bust — Left)	-
2/2.3,(Refer fig 4.3I of Part4) (Dimensions of Fig 4.3 I Front Top End Plate)	-
2/2.3,(Refer fig 4.3IJof Part4) (Dimensions of 4.3J Front Bottom End Plate)	-
2/2.3,(Refer fig 4.3IKof Part4) (Dimensions of Fig 4.3K Gusset — Standard w (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3L Jof Part4) (Dimensions of Fig 4.3L Gusset — EDWP (For EDWP) )	-
2/2.3,(Refer fig 4.4 Jof Part4) (Dimensions of FIG. 4.4 FRONTCOVER)	-
2/2.3,(Refer fig 4.5A of Part4) (Dimensions of FIG. 4.5A Flange for Third Plate)	-
2/2.3,(Refer fig 4.5 B of Part4) (Dimensions of FIG. 4.5B Guide Bush )	-
2/2.3,(Refer fig 4.6 of Part4) (Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.7 of Part4) (Dimensions of FIG.4.7 HANDLE— EDWP)	-
2/2.3,(Refer fig 4.8A of Part4) (Dimensions of FIG 4.8A Handle Bar — Standard (For SDWR VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.8B of Part4) (Dimensions of FIG 4.8B Handle Bar — EDWP)	-
2/2.3,(Refer fig 4.8C of Part4) (Dimensions of FIG 4.8C Chain Guide)	-
2/2.3,(Refer fig 4.8 D of Part4) (Dimensions of Fig 4.8D Bearing Housing )	-
2/2.3,(Refer fig 4.9 of Part4) (Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-
2/2.3,(Refer fig 4.10 of Part4) (Dimensions of FIG. 4.10 T-BAR (For EDWP only))	-
2/2.3,(Refer fig 4.11 of Part4) (Dimensions of FIG; 4.11 COUNTER WEIGHT (For EDWP only))	-
2/2.3,(Refer fig 4.12A of Part4) (Dimensions of Fig 4.1 2A Telescopic Stand — Standard (For borewell with 150 NB casing pipe)(For SDWP, VLOM-65 & VLOM-50))	-

Partial

-
-

111

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.4 ( Line/ Cord beading IS 7903)	-
5.1.1 (Lamination IS 7903)	-
5.1.2 (Lamination IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.2.1 (Construction IS 7903)	-
5.3 (Joint/Seam, IS 7903)	-
5.4 (Fixing of Eyelets, IS 7903)	-
5.4 (Fixing of Eyelets ,IS 7903)	-
6.1 Table 1,i) (No of HDPE fabric layers ,IS 7903)	-
6.1 Table 1,ii) (No of lamination layers, IS 7903)	-
6.1 Table 1, iii) (Total no of layers in the finished tarpaulin, IS 7903)	-
6.1 Table 1,iv) (Mass of finished tarpaulin, Annex B ,IS 7903)	-
6.1 Table 1,v) (Mass of laminated fabric, Annex C , IS 7903)	-
6.1 Table 1vi) (Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-
6.1 Table 1vi) (Breaking strength before UV exposure,weft, IS 1969 part 1)	-
6.1 Table 1 ix) (Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-
6.1 Table 1 vii) (Elongation at break of fabric,warp, IS 1969 Part 1)	-
6.1 Table 1 vii) (Elongation at break of fabric,weft, IS 1969 Part1)	-
6.2 (Length, IS 7903)	-
6.2 (Width, IS 7903)	-
6.2 (height, IS 7903)	-
6.1 Table 1 xv) (Ash Content, Annex F of IS 7903)	-

Partial

-
-

112

IS 15138 (2010)

Textiles – Jute bags for packing 50 kg sugar – Specification (first revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Fabric)	-
4.1.1 (Fabric)	-
4.2 IS 9113 (Seam )	-
4.3 IS 9113 (Hemming at the Mouth )	-
4.4 Annex B (Freedom from Defects)	-
5,5.1,5.2 Table 1,i) a) Cl.8.3.2 of IS 9113 Table A / B / C ( Outside length )	-
5,5.1,5.2 Table 1,i) b) Cl.8.3.2 of IS 9113 Table A / B / C (Outside width)	-
5,5.1,5.2 Table 1,ii) Cl.8.4.2 of IS 9113 Table A / B / C (Ends/dm)	-
5,5.1,5.2 Table 1,iii) Cl.8.4.2 of IS 9113 Table A / B / C (Picks/dm)	-
5,5.1,5.2 Table 1,iv) Cl.8.5.2 of IS 9113 Table A / B / C (Corrected mass per bag)	-
5,5.1,5.2 Table 1,v) a) Cl.8.6.2 of IS 9113 Table A / B / C (Average breaking load of sacking (ravelled strip method, 5.0 cm × 20.0 cm), Min, N (kgf) Warpway:)	-
5,5.1,5.2 Table 1,v) b) Cl.8.6.2 of IS 9113 Table A / B / C (Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Weftway :)	-
5,5.1,5.2 Table 1,vi) a) Cl.8.7 of IS 9113 Table A / B / C ( Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Warpway:)	-
5,5.1,5.2 Table 1,vi) b) Cl.8.7 of IS 9113 Table A / B / C ( Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Weftway :)	-
5,5.1,5.2 Table 1,vii)a) Cl.8.2 of IS 9113 Table A / B / C (Moisture regain)	-
5.3 Table 2 v) Cl.8.8 of IS 9113 (Oil content on dry deoiled material basis)	-

Complete

-
-

113

IS 16333 : Part 3 (2017)

Mobile phone handsets: Part 3 indian language support for mobile phone handsets - Specific requirements (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

114

IS 14899 (2014)

Liquefied petroleum gas (LPG) containers for automotive use - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.1,12,2,12,3 (Marking)	-
10.1.6 (Macroscopic Examination On Circumferential Weld )	-
10.1.6 (Macroscopic Examination On longitudinal Weld)	-

Partial

-
-

115

IS 7138 (1973)

Specification for steel tubes for furniture purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

116

IS 6046 (1982)

Specification for gypsum for agricultural use (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 (Sodium Content)	-
2.2 (Calcium Sulphate Content)	-
2.1 (Fineness)	-

Complete

-
-

117

IS 12444 (2020)

Copper Wire Rods for Electrical Applications — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Dimension)	-
6.2.2 (Ovality)	-
7.0 (Freedom from Defects)	-
8.1 (Tensile Strength)	-
8.2 (Surface Compression Test)	-

Partial

-
-

118

IS 4605 (1981)

Specification for crepe bandage (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

119

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Sulphur-Percentage by mass)	-
4.1 (Phosphorus-Percentage by mass)	-
6.0 (Workmanship)	-
8.0 (Straightness)	-
11.1 (Surface Protection)	-
19.1.1, 24.1.1, 28.1.1, 33.1.1 (Dimensions- Outside Dia)	-
19.1.2, 24.1.2, 28.1.2, 33.1.2 (Dimensions- Thickness)	-
11.2 (Surface Protection)	-
13.1.3 (Tensile Strength)	-
13.1.1 (Yield Stress)	-
13.1.2 (Elongation)	-
13.2 (Flattening Test)	-
13.3 (Bend Test (Strip))	-
13.4 (Bend Test (Whole Tube))	-
13.5 (Drift Expansion Test)	-
19.1.3 (Height of Internal Fin)	-

Partial

-
-

120

IS 7283 (1992)

Hot - Rolled bars for the production of bright bars and machined parts for engineering applications specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Workmanship)	-
Cl 7 (Diameter & Out Of Round)	-
5, 5.1, 5.2 (Chemical Composition - Carbon)	-
5, 5.1, 5.2 (Chemical Composition - Sulphur)	-

Partial

-
-

First
Prev
3
4
5
6
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List