BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List

Reset

366 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

151

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Workmanship)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Carbon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Sulphor)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Phosphorous)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Manganese)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Silicon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Chromium)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Nickel)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Molybdenum)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Copper)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Nitrogen)	-

Partial

-
-

152

IS 903 (1993)

Specification for Fire Hose Delivery Couplings, Branch Pipe, Nozzles And Nozzle Spanner - Specificaion

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Finish and workmanship)	-
5 (Delivery hose coupling)	-
5 (Delivery hose coupling)	-
5 (Delivery hose coupling)	-
5 (Delivery hose coupling)	-
5.3 (Size and Dimension )	-
5.3 (Size and Dimension )	-
5.3 (Size and Dimension )	-
5.3 (Size and Dimension )	-
3 (Finish and workmanship)	-
5.3 (Size and Dimension )	-

Partial

-
-

153

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 10 (Diameter & Out Of Round)	-
Cl 10 (Diameter & Out Of Round)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Carbon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Silicon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Manganese)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Nickel)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Chromium)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Phosphorous)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Copper)	-

Partial

-
-

154

IS 1322 (1993)

Bitumen Felts for Water Proofing and Damp-proofing

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4 & Table 1 (Weight )	-
5.5 (Free from external defects - IS 1322)	-
6 (Dimension-IS 1322)	-
7.1 (Breaking Strength test- IS 13826(Part 1))	-
7.1 (Pliabilitry Test-IS 13826(Part 2))	-
7.1 (Strage Sticking Test-IS 13826(Part 3))	-
7.1 (Pressure Head Test-IS 13826(Part-4 )	-
7.1 (Heat Resistance Test-IS 13826(Part 5))	-
7.1 (Water Absorption Test-IS 13826(Part 6))	-

Complete

-
-

155

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-
4.4 (Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-
4.4 (Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-
4.4 (Seam The stitching shall be done with double fold over seam to)	-
4.4 (The number of stitches/dm shall be 14 ± 2.)	-
5/5.1-Table 1-Sr. no. iv (Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-
5/5.1-Table 1-Sr. no. iv (Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-
5/5.1 (The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-
5/5.3-Table 1-Sr. no.v (Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-
5/5.3-Table 1-Sr. no.v (Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-
5/5.3-Table 1-Sr. no.vi (Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-
5/5.3-Table 1-Sr. no.vi (Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-
5/5.3-Table 1-Sr. no.vii (Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-
5/5.3-Table 1-Sr. no.vii (Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-
5/5.5-Table 1-Sr. no.viii (Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-
5/5.5-Table 1-Sr. no.viii (Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-

Partial

-
-

156

IS 13095 (1991)

Butterfly valves for general purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (SERVICE APPLICATIONS)	-
6 ( NOMINAL SIZES )	-
7 (NOMINAL PRESSURES)	-
7.2 (Class designations)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck- r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -d2 )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck-r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Pipe O.D.- d1)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling - Nos.)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange -D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange - b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling - Nos.)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -k)	-
9.1.1 ( Double Flanged Body Ends)	-
9.2.2 (Wafer Body Ends)	-
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-
11 (Bodies)	-
12 (DISC AND SHAFT)	-
13 (SEATING AND LININGS)	-
14.2 (BEARINGS)	-
14.3 (BEARINGS)	-
16 (OPERATION)	-
4 (VALVE END CONNECTIONS)	-

Partial

-
-

157

IS 6419 (1996)

Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Diameter)	-
8 (Dimension of Spools, Rims & Coils)	-
9 (Lengthof Rods)	-
10.2.1 Table 5 (Tensile Strength-IS 1608(P-1))	-

Partial

-
-

158

IS 11587 (1986)

Specification for structural weather resistant steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Tensile Test)	-
Cl 9 (Bend Test)	-
Cl 10 (Impact Test)	-
Cl 11 (Flattening Test)	-
Cl 12 (Freedom from Defects)	-
Cl 13 (Dimensions)	-
Cl 16 (Mass)	-

Complete

-
-

159

IS 459 (1992)

Corrugated and semi - Corrugated asbestos cement sheets - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Depth of Corrugation, D - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Pitch of Corrugation, P - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Overall width, B - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Effective Width, C - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Nominal Thickness, T - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Length of Sheet, A - Cl. 5)	-
7 (General Appearance and Finish - Cl. 7.1)	-
7 (General Appearance and Finish - Cl. 7.2)	-

Partial

-
-

160

IS 5852 (2004)

Protective Steel Toe Caps for Footwear

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5/5.1- Fig. 1 and Fig. 2, Table 1. (REQUIREMENTS-Shape and Dimension)	-
5/5.2 (REQUIREMENTS-Performance Test- as per Annex A,)	-
5/5.3 (REQUIREMENTS-Finish)	-

Complete

-
-

161

IS 13620 (1993)

Fusion Bonded Epoxy Coated Reinforcing Bars -

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7.2 (Continuity Of Coating)	-
Cl 7.3 (Adhesion )	-
4.1 (Carbon- IS 228(Part 1))	-
4.1 (Sulphur- IS 228(Part 9))	-
4.1 (Phosphorous- IS 228(Part 3))	-
4.1 (Sulphur & Phosphorous)	-
4.1 (Carbon Equivalent)	-

Partial

-
-

162

IS 6192 (1994)

Textiles – Monoaxially oriented high density polyethylene tapes – Specification (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6 (Heat Shrinkage at 60 degree C(For test method Refer IS 6193:1971) )	-
5.6 (Heat Shrinkage at 95 degree C(For test method Refer IS 6193:1971) )	-
5.5 (Thickness (For test method Refer IS 6193:1971))	-
5.4 (Finished width (For test method Refer IS 6193:1971))	-

Partial

-
-

163

IS 1912 (1984)

Specification for country jute twine (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 (Yarn)	-
2.3 (Twine)	-
2.4 (Skein)	-
2.6 (Moisture Regain)	-
3 / 3.1 (REQUIREMENTS, table -1)	-

Complete

-
-

164

IS 12016 (1987)

Specification for cypermethrin EC

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

165

IS 1989 : Part 2 (1986)

Specification for leather safety boots and shoes: Part 2 for heavy metal industries (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Marking)	-
7 (Design)	-
8 (a) Upper Leather)	-
8 (b) Lining Leather)	-
8 (c) Bottom Material)	-
8 (d) Steel Toe Cap)	-
8 (e) Tape)	-
8 (f) Bottom Filling)	-
8 (g) Eyelet)	-
8 (h) Toe Compound)	-
8 (i) Threads)	-
8 (j) Rivets)	-
8 (k) Screw Wire)	-
8 (l) Heel Pin)	-
8 (m) Shank)	-
8 (n) Laces)	-
8 (o) Tongue Lining)	-
8 (p) Adhesive)	-
8 (q) Strengthening Piece)	-
8 (r) Leather Components)	-
9 (Manufacture)	-
10 (Finish)	-
11 (a) Boots with Leather Sole and Heel)	-
11 (b) Boots with Rubber Sole and Heel)	-
12 (Performance Test)	-
13 (Design)	-
14 (a) Upper Leather)	-
14 (b) Lining Leather)	-
14 (c) Bottom Material)	-
14 (d) Steel Toe Cap)	-
14 (e) Tape)	-
14 (f) Bottom Filling)	-
14 (g) Eyelet)	-
14 (h) Toe Compound)	-
14 (i) Threads)	-
14 (j) Rivets)	-
14 (k) Screw Wire)	-
14 (l) Heel Pin)	-
14 (m) Shank)	-
14 (n) Laces)	-
14 (o) Tongue Lining)	-
14 (p) Adhesive)	-
14 (q) Leather Components)	-
15 (Manufacture)	-
16 (Finish)	-
17 (a) Shoes with Leather Sole and Heel)	-
17 (b) Shoes with Rubber Sole and Heel)	-
18 (Performance Test)	-

Partial

-
-

166

IS 13714 (1993)

Dunnage pallets - Warehousing - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (DIMENSIONS)	-
4.1 (DIMENSIONS)	-
4.1 (DIMENSIONS)	-
5.1 Annex A (Timber)	-
5.1.1 (Timber)	-
5.1.2 (Timber)	-
5.1.2 (Timber)	-
5.1.2.1 (Objectionable knots)	-
5.1.2.1 (Objectionable knots)	-
5.2.1 (Nails)	-
5.2.1 (Nails)	-
6.1 , Fig. 1 (CONSTRUCTION)	-
6.1.1 (CONSTRUCTION)	-
6.1.2 (CONSTRUCTION)	-
6.1.2 (CONSTRUCTION)	-
6.1.2 (CONSTRUCTION)	-
7 (WORKMANSHIP AND FINISH)	-

Complete

-
-

167

IS 12650 (2018)

Textiles – Jute bags for packing 50 kg foodgrains – Specification (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4-4.1 (MANUFACTURE- The bags shall be made from single piece of twill weave jute sacking of uniform construction having nominal mass of 579 g/m2 as given below with warp running along the length of the bag:)	-
4-4.2 (Manufacture)	-
4-4.2 (Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-
4-4.2 (Manufacture)	-
4-4.3 (Manufacture-Safety Stitch-The number of safety union stitches per decimetre shall be10 ± 1.)	-
4-4.5 (Manufacture- Freedom from Defects )	-
5-5.1-Table 1-Sr. no.iv) (SPECIFIC REQUIREMENTS-Cl. 8.5.2 of IS 9113 Corrected Mass/bag, g ( See Note 2) For both Type A & Type B 665 + 8.0 / -6.0 percent)	-
5-5.1-Table 1-Sr. no. i) (SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 a) Out side Length , cm 94 (For both type A & Type B) Tolerance + 4 / -0 cm)	-
5-5.1-Table 1-Sr. no. i) (SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 b) Outside width, cm 57 (For both type A & Type B) Tolerance + 4 / -0 cm)	-
5-5.1-Table 1-Sr. no.i i) (SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Ends/dm Type A 46 + 2 /Type B 76 + 4 / -3)	-
5-5.1-Table 1-Sr. no.iii) (SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Picks/dm Type A 50 (2 x 25) / Type B 28 + 2)	-
5-5.1-Table 1-Sr. No.vii) (SPECIFIC REQUIREMENTS-Cl. 8.2 of IS 9113 Moisture regain, percent, Max (see Note 3) 22 for both type A & Type B)	-
5-5.1-Table 1-Sr. No.v) (SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): a ) Warpway- 1570 (160) for both type A & Type B)	-
5-5.1-Table 1-Sr. No.v) (SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): b ) Weftway- 1420 (145) for both type A & Type B)	-
5-5.1-Table 1-Sr. No.vi) (SPECIFIC REQUIREMENTS-Cl. 8.7 of IS 9113 Average side seam strength (5 cm ×20 cm raveled strip), Min, N (kgf): 490 (50) for both type A & Type B)	-
5-5.1-Table 1-Sr. No.viii) (SPECIFIC REQUIREMENTS-Cl. 8.8 of IS 9113 Oil content on dry de-oiled material, Max 3 for both type A & Type B)	-

Partial

-
-

168

IS 2573 (1986)

Specification for leather gauntlets and mittens (Second Revision)

- View breakup
Rs.7400/- (excluding shrinkage temperature test and test of length)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.2.1, Table 1, Sr. No. 1 (Solvent extractable substances)	-
Cl 4.2.1, Table 1, Sr. No. 2 (Chromium content, (as Cr₂O₃))	-
Cl 4.2.1, Table 1, Sr. No. 3 (pH of aqueous extract)	-
Cl.4.1 Fig. 1 to 3. (The three types shall be made to the shape and design as shown in Fig. 1 to 3.)	-
Cl .4.2.1 ( Leather - Chrome tanned/ chrome retanned full grain leather or flesh splits manufactured from cow or buffalo hides conforming to the following requirements shall be used a) The leather and flesh split shall have thickness of 1.0 to 1.5 mm;)	-
Cl.4.3.1.2 ( The hand part shall be cut from the piece of undyed leather and back portion including second, third and fourth fingers from different pieces of undyed leather.)	-
Cl. 4.3.1.3 ( The three different pieces of back portion shall be assembled and stitched together along the edges by a row of stitches. The back thus formed shall be secured with the corresponding front pieces ( palm side ) of the fingers with a row of stitches. The thumb shall be made from two pieces of undyed leather and closed with the hand part by a seam. The seam of the thumb shall be reinforced by a strip of leather and secured by two rows of stitches.)	-
Cl 4.3.1.4 ( The hand part shall be made with the flesh side up and the grain side to remain in contact with the hand.)	-
Cl.4.3.1.5 ( The cuff portion shall be made from two pieces of leather, the inner portion being of leather, chrome tanned, natural colour and the outer portion made of chrome tanned leather, with grain side out.)	-
Cl.4.3.2.6 ( The joint at the palm and the thumb shall be reinforced with the same quality of leather as used for the inner face and stitched by two rows of stitches.)	-
Cl.4.3.1.7 ( A dyed leather piece cut to the shape of a semi-circle shall be stitched on the inner part of the cuff along the joint of the hand and the cuff portions by a single row of stitches as shown in Fig. 1. The semi-circular piece of leather shall be not less than 75 mm in diameter.)	-
Cl.4.3.1.8 ( The gauntlets shall be machine stitched.)	-
Cl.4.3.1.9 ( The number of stitches for all the stitchings shall be 6 to 8 stitches per 25)	-
Cl.4.3.1.10 (All losse ends of stitching threads shall be securely fastened)	-
Cl.4.3.1.11 ( ship and finish, and in all other respects not defined in this standard, the gauntlets shall conform to the approved sample.)	-
Cl.4.3.2.2 ( The inner face of the gauntlets including the inner portion of index, second, third and fourth fingers shall be cut from one piece of leather. The thumb shall be cut from a separate piece of leather.)	-
Cl.4.3.2.3 ( The leather components shall be assembled with the flesh side up, the grain side being inside.)	-
Cl.4.3.2.4 ( The outer face of the gauntlets including index second, third and fourth fingers shall be cut from one piece of canvas.)	-
Cl.4.3.2.5 ( The thumb shall be made with the two cut sides placed together and stitched with one row of stitches. The thumb thus formed shall be attached to palm portion through the cut hole and secured by two rows of stitches as shown in Fig. 2.)	-
Cl.4.3.2.6 ( The joint at the palm and the thumb shall be reinforced with the same quality of leather as used for the inner face and stitched by two rows of stitches.)	-
Cl.4.3.2.7 ( The back portion made of canvas shall be secured with the corresponding palm piece made of leather by two rows of stitches with the edges of both leather and canvas placed inside.)	-
Cl.4.3.2.8 ( A leather strip, 20 mm wide and of the same quality of leather used for the inner face of the gauntlet, shall be used for reinforcing the face of canvas over the knuckles. The reinforcement piece shall be placed side up and secured by four rows of stitches.)	-
Cl.4.3.2.9 ( The cuff portion shall be made from one piece of canvas, the side edges being stitched together by double row of stitches with the ends placed inside. The cuff thus formed shall be secured to the hand part by two rows of stitches with the edges of the material placed inside. The bottom edge of the cuff shall be hemmed ( 6 mm ) with the row edges properly turned in.)	-
Cl.4.3.2.10 ( the gauntlets shall be machine stitched.)	-
Cl.4.3.2.11 ( The number of stitches for all the stitchings shall be 6 to 8 stitches per 25 mm. All loose ends of stitching threads shall be securely fastened.)	-
Cl.4.3.2.12 ( Workmanship and finish, and in all other respects not defined in this standard, the gauntlets shall conform to the approved sample.)	-
Cl.4.3.3.2 ( The palm including the inner component of the compartment for the four fingers shall be cut from one piece of leather and the thumb from a separate piece.)	-
Cl.4.3.3.3 ( The leather components shall be assembled with the flesh side out, the grain side being inside.)	-
Cl.4.3.3.4 ( The back portion including the outer component of the compartment for the four fingers shall be cut from one piece of canvas.)	-
Cl.4.3.3.5 ( The thumb shall be made with the two sides placed inside and stitched with a row of stitches. The thumb thus formed shall be attached to the palm through the cut hole and secured by two rows of stitches.)	-
Cl.4.3.3.6 (The joint at the palm and the thumb shall be reinforced by the same leather material and stitched by two rows of stitches as shown in Fig. 3.)	-
Cl.4.3.3.7 ( The back portion made of canvas shall be secured with the corresponding palm piece made of leather by two rows of stitches with the edges of both the leather and canvas placed inside.)	-
Cl.4.3.3.8 ( The entire palm portion may be lined with canvas of the same quality as used for the back, if required by the purchaser.)	-
Cl.4.3.3.9 (The reinforcement piece shall be placed flesh side out and secured by four rows of stitches.)	-
Cl.4.3.3.10 (The cuff portion shall be made from one piece of canvas, the side edges being stitched together with two rows of stitches with the ends placed inside.)	-
Cl.4.3.3.11 ( The cuff thus formed shall be secured to the hand part by two rows of stitches all along their edges and turned over subsequently.The bottom edges of the cuff shall be hemmed. 6.0 mm with the raw edge properly,turned in.)	-
Cl.4.3.3.12 ( The mittens shall be machine stitched.)	-
Cl.4.3.3.13 ( The number of stitches for all stitchings shall be 6 to 8 stitches per 25 mm)	-
Cl.4.3.3.14 ( All loose ends of stitching threads shall be securely fastened.)	-
Cl.4.3.3.15 (workmanship and finish, and in all other respects not defined in this standard, the mittens shall conform to the approved sample.)	-

Partial

-
-

169

IS 2002 (2009)

Steel plate for pressure vessel for intermediate and high temperature service including boilers (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 ( Nitrogen%)	-
6.1 ( Copper %)	-
Cl 12 (UTM)	-

Partial

-
-

170

IS 14106 (2018)

Direct action hand pumps - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Visual tests: All the pumps shall be examined for workmanship, finish and visual defects.)	-
6.2.2 (i) Aligment of groove in top guide bush with respect to the nuts welded on pump body)	-
6.2.2 (ii) Aligment of handle nut with pipe for concentricity)	-
6.2.2 (iii) Location of holes in the pump head flange with respect to the direction of the spout)	-
6.2.2 (iv) Reasonable flatness of the flanges to provide proper matching of the holes to ensure unrestricted insertion of the bolts )	-
6.2.2 (v) Matching of faces indicated in respective figures of piston plate, follower plate and foot valve body)	-
6.2.2 (vi) Concentricity of the two internal diameter of the reducing socket)	-
4.4 & Table 2 (a)Socket Depth)	-
4.4 & Table 2 (b) Mean socket internal dia at mouth)	-
4.4 & Table 2 (c) Mean socket internal diameter at root )	-
4.4 & Table 2 (a)Socket Depth)	-
4.4 & Table 2 (b) Mean socket internal dia at mouth)	-
4.4 & Table 2 (c) Mean socket internal diameter at root )	-
4.4 & Table 2 (a)Socket Depth)	-
4.4 & Table 2 (b) Mean socket internal dia at mouth)	-
4.4 & Table 2 (c) Mean socket internal diameter at root )	-
6.2.3 (A1)	-
6.2.3 (A2)	-
6.2.3 (A3 )	-
6.2.3 (A4)	-
6.2.3 (B1)	-
6.2.3 (C1)	-
6.2.3 (C2)	-
6.2.3 (C3)	-
6.2.3 (C4)	-
6.2.3 (D1)	-
6.2.3 (D2)	-
6.2.3 (D3)	-
6.2.3 (D4)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (E1)	-
6.2.3 (E2)	-
6.2.3 (E3)	-
6.2.3 (E4)	-
6.2.3 (E5)	-
6.2.3 (F1)	-
6.2.3 (G1)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (G2)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (G3)	-
6.2.3 (G4)	-
6.2.3 (H3)	-
6.2.3 (H6)	-
6.2.3 (J1)	-
6.2.3 (J2)	-
6.2.3 (J3)	-
6.2.3 (J4)	-
6.2.3 (J5)	-
6.2.3 (J6)	-
6.2.3 (J7)	-
6.2.3 (J8)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (J9)	-
6.2.3 (J10)	-
6.2.3 (J11)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (J13)	-
6.2.3 (J14)	-
6.2.3 (J15)	-
6.2.3 (J16)	-
6.2.3 (J18)	-
6.2.3 (J19)	-
6.2.3 (K2)	-
6.2.3 (K4)	-
6.2.3 (K5)	-
6.2.3 (K6)	-
6.2.3 (K7)	-
6.2.3 (K8)	-
6.2.3 (K9)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (K10)	-
6.2.3 (K11)	-
6.2.3 (K12)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (K13)	-
6.2.3 (K14)	-
6.2.3 (L3)	-
6.2.3 (L4)	-
6.2.3 (L6)	-
6.2.3 (L8)	-
6.2.3 (L11)	-
6.2.3 (L12)	-
6.2.3 (L13)	-
6.2.3 ( Shore Hardness on Scale A)	-
6.2.3 (L14)	-
6.2.3 (L15)	-
6.2.3 (M4)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (M5)	-
6.2.3 (M6)	-
6.2.3 (M7)	-
6.2.3 (M8)	-
6.2.3 (N1)	-
6.2.3 (N2)	-
6.2.3 (N3)	-
6.2.3 (N4)	-
6.2.3 (P4)	-
6.2.3 (P5)	-

Partial

-
-

171

IS 781 (1984)

Specification for cast copper alloy screw down bib taps and stop valves for water services (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3 (Nominal Size)	-
Cl 5 (Dimensions & Tolerances)	-
Cl 6.1 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.3 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.4 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.5 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.7 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.8 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.11 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 8 (Finish)	-

Partial

-
-

172

IS 15658 (2006)

Precast concrete blocks for paving - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1.2 (Physical requirement)	-
6.2.1 & 7.1 (VISUAL INSPECTION)	-
B-1.3.1 (MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-
B-5 (AVERAGE WIDTH (Average for eight test specimens), W)	-
B-1.3.1 (MEAN INDIVIDUAL LENGTH (of all eight test specimens), L)	-
B-5 (AVERAGE LENGTH (Average for eight test specimens), L)	-
Table 1 (MINIMUM PAVER BLOCK THICKNESS)	-
B-1.3.2 (MEAN INDIVIDUAL THICKNESS (of all eight test specimens), T)	-
B-1.3.3 (INDIVIDUAL ASPECT RATIO (L/T) (of all eight test specimens))	-
B-5 (AVERAGE ASPECT RATIO (L/T) (for eight test specimens))	-
B-2.3 (INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-
B-5 (AVERAGE ARRIS/CHAMFER (for eight test specimens))	-
B-5 (INDIVIDUAL PLAN AREA, ASP (of all eight test specimens) )	-
B-5 (AVERAGE PLAN AREA, ASP (for eight test specimens))	-
B-5 (INDIVIDUAL WEARING FACE AREA, Asw (of all eight test specimens))	-
B-5 (AVERAGE WEARING FACE AREA, Asw (for eight test specimens))	-
B- 4.3 (MEAN INDIVIDUAL SQUARENESS (of all eight test specimens) )	-
B-5 (AVERAGE SQUARENESS (for eight test specimens))	-
6.2.3 (THICKNESS OF WEARING LAYER, if the sample is Double Layered (for eight test specimens))	-
6.2.4 (WATER ABSORPTION TEST (Average for three test specimens))	-
6.2.4 (WATER ABSORPTION TEST (Average for three test specimens))	-
6.2.6 (ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-
6.2.6 (ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-
6.2.6 (ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-
6.2.6 (ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-

Partial

-
-

173

IS 14246 (2013)

Continuously pre-painted galvanized steel sheets and coils (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.2 (Press)	-
Cl 6.3 (HWB)	-
Cl 6.4 (Load Resistance)	-
Cl 6.5 (Cross Hatch)	-
Cl 9 (Length, Width, Thickness & Mass)	-
Cl 9 (Length, Width, Thickness & Mass)	-
Cl 9 (Length, Width, Thickness & Mass)	-
Cl 9 (Length, Width, Thickness & Mass)	-
Cl 10 (Camber, Deviation From Squareness (Out-of- Square) & Deviation From Flatness)	-
Cl 4.1 (Workmanship)	-

Partial

-
-

174

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Tensile Test & Flattening Test)	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 9 (Pipe ends, Angle of bevel & Root Face )	-
Cl 12 (Bituminous Coating & Galvanizing )	-
Cl 14 (Workmanship)	-
5.2 (sulphur)	-
5.2 (phosphorus)	-

Partial

-
-

175

IS 4454 : Part 2 (2001)

Steel wire for mechanical springs - Specification february 2001: Part 2 oil hardened and tempered steel wire (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
7.1, 7.2 (carbon)	-
7.1, 7.2 (sulphur)	-
7.1, 7.2 (phosphorus)	-
7.1, 7.2 (manganese)	-
7.1, 7.2 (silicon )	-
7.1, 7.2 (copper)	-
7.1, 7.2 (Chromium)	-

Partial

-
-

176

IS 11226 (1993)

Leather safety footwear having direct moulded rubber sole specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (REQUIREMENTS)	-
5.2.5 (Materials)	-
5.2.6 (Materials)	-
5.2.6.1 (Materials)	-
5.2.6.2 (Materials)	-
5.2.6.3 (Materials)	-
5.2.7 (Materials)	-
5.2.8 (Materials)	-
5.2.9 (Materials)	-
5.2.10 (Materials)	-
5.2.11 (Materials)	-
5.2.11.1 (Materials)	-
5.2.11.2 (Materials)	-
5.2.11.3 (Materials)	-
5.3 (Components)	-
5.4 ( Manufacture )	-
5.4.1 ( Manufacture )	-
5.4.8 (Workmanship and Finish)	-
5.5 (Mass)	-
5.6 (Performance Test)	-

Partial

-
-

177

IS 797 (1982)

Specification for common salt for chemical industries (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3.1 (Description)	-
Cl.3.2.1 (Moisture Content For Grade 1 material (Annex A2))	-
Table 1 Cl.3.3 (Sodium Chloride (as NaCl) For Grade 1 material (Annex A3))	-
Table 1 Cl.3.3 (Material insoluble in water For Grade 1 material (Annex A4))	-
Table 1 Cl.3.3 (Calcium salts (as Ca) For Grade 1 material (Annex A5))	-
Table 1 Cl.3.3 (Magnasium salts (as Mg) For Grade 1 material (Annex A5))	-
Table 1 Cl.3.3 (Sulphates (as SO4) For Grade 1 material (Annex A6))	-
Table 1 Cl.3.3 (Iron compound (as Fe) For Grade 1 material (Annex A7))	-

Partial

-
-

178

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 (Surface colour of the pipes shall be dark shade of grey)	-
Cl.7.1 (Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.1 ( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.1 (Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.2 (Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-
Cl.7.3.1 (Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-
Cl.7.3.2 (Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-
Cl.8.1 (The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-
Cl.8.2 (When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-
Cl8.3 (This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-
Cl.8.4 (When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-
Cl.8.5 (After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-
Cl.10.1 (When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-
Cl.10.2 (When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-
Cl.10.3 (The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-
Cl.7.1 ( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.1 ( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.3.1 (Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-

Partial

-
-

179

IS 5346 (1994)

Synthetic food colour - Preparations and mixtures - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.6 Table 1 (Water InsoIuble matter,)	-
Clause 4.6 Table 1 (Heavy metals)	-
Clause 4.5 (Total dye Content)	-

Partial

-
-

180

IS 208 (1996)

Door Handles - Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017) (Chemical composition - Carbon - IS 228)	-
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017) (Chemical composition - Manganese - IS 228)	-
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017) (Chemical composition - Phosphorus - IS 228)	-
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017) (Chemical composition - Sulphur - IS 228)	-
5.1 (MANUFACTURE- General)	-
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972))	-

Partial

-
-

First
Prev
5
6
7
8
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List