BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List

Reset

366 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 745 (2003)

Textiles – Handloom cotton bed sheets – Specification (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1,Table 1 (REQUIREMENTS-(Refer table 1 and IS 1963,1964 or Annex D, 1969))	-
5.3,B-1 (Dimensions- (Refer IS 1954 and Annex B)- Legth of A trade description of length stamped on grey, bleached, mercerized or coloured cotton piece goods:)	-
5.3,B-2 (Dimensions- (Refer IS 1954 and Annex B)- width of A trade description of length stamped on grey, bleached, mercerized or coloured cotton piece goods:)	-

Partial

-
-

IS 844 : Part 1 (1979)

Specification for screwdrivers: Part 1 techincal supply conditions (Second Revisionn)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Hardness)	-
5.1,Table 1 ( Dimension, axb)	-
5.1,Table 1 (t)	-
5.1,Table 1 (r)	-
5.2,Table 2 (l)	-
6.1 (Free from Defects)	-
6.2 (Finish of Handle)	-
6.3 (Alignment )	-
7 (Finish)	-
8.2 (Stricking Test)	-

Partial

-
-

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2) (requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-
Cl.5.2.3 Coated Binding Material IS 1954 ( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-
Cl.5.2.3 Coated Binding Material Annex C (ii) Breaking load in N, Min (50 cm grip length test specimen) )	-
CL.5.2.10 Counter Stiffener ( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5) ( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-
Cl.5.2.3 Coated Binding Material IS 1954 ( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1). ( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4) (ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-
Cl.5.2.5.3 Ageing for whole footwear (When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-
Cl.5.2.9 Eyelets ( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener ( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-
Cl.5.5 Mass (The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-
Cl.5.10 Consolidation Test ( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener ( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-
Cl.5.6 ( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5) ( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-
Cl.6.2 Flexing Resistance of Compact Outsole ( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-

Partial

-
-

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2.2, Table 2 (Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-
3.2.2, Table 1 (Dimension of 11 1/4° bends)	-

Partial

-
-

IS 513 : Part 2 (2016)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (CARBON)	-
6.0 (SULPHUR)	-
6.0 (PHOSPHORUS)	-
6.0 (MANGANESE)	-
6.0 (SILICON)	-
6.0 (NITROGEN)	-
Cl 7 (UTM)	-
Cl 9 (Workmanship)	-
Cl 10 (Length, Width & Thickness)	-

Partial

-
-

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2.2, Table 1 (Dimensions of 22 ½ deg Bends)	-
3.2.2, Table 2 (Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-

Partial

-
-

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2.2, Table 1 (Dimensions of 30 deg Bends)	-
3.2.2, Table 2 (Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-

Partial

-
-

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.0 (CARBON)	-
7.0 (SULPHUR)	-
7.0 (PHOSPHORUS)	-
7.0 (MANGANESE)	-
7.0 (SILICON)	-
7.0 (NITROGEN)	-
Cl. 8.1 & Table 5A, 5B & 5C (Yield Stress)	-
Cl. 8.1 & Table 5A, 5B & 5C (Elongation at 50 mm gauge length)	-
Cl. 8.1 & Table 5A, 5B & 5C (Elongation at 80 mm gauge length)	-
Cl. 8.2 (Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-
Cl. 8.3 Table 6 (Hardness Test ( Only for CR0 & CR1))	-
Cl. 8.4 (Bend Test)	-
Cl. 11 (Thickness)	-
Cl. 11 (Width)	-
Cl 10 (Workmanship)	-

Partial

-
-

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2, 3.2.1, Fig 2 (Manufacture)	-
3.2.2, Fig 1, table 1 (Dimensions)	-
Table 2 (Clause 3.2.2, and Fig. 2) (Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-

Partial

-
-

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2, 3.2.1, Fig 2 (Manufacture)	-
3.2.2, Fig 1, table 1 (Dimensions)	-

Partial

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2, 3.2.1, Fig 2 (Manufacture)	-
3.2.2, Fig 2, table 2 (Dimensions)	-

Partial

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2.2, Fig 2, table 2 (Dimensions)	-

Partial

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2, 3.2.1, Fig 1 (Manufacture)	-
3.2.2, Fig 1 (Dimensions)	-

Partial

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (General)	-
3.2, 3.2.1, Fig 1 (Manufacture)	-
3.2.2, Fig 1 (Dimensions)	-
Table-1 (cl.3.2.2, Fig 1) (Dimensions of Straight Reducers)	-
3.2.2, Fig 1 (Dimensions)	-
Table-1 (cl.3.2.2, Fig 1) (Dimensions of Straight Reducers)	-

Partial

-
-

IS 17216 (2019)

Polyethylene Mulch Films for Agriculture and Horticulture • Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (Density)	-
5.1.2 (Melt Flow Index)	-
5.2.1 (Visual Appearance)	-
5.2.2 (Film Form)	-
5.2.4 (Odour)	-
5.3.1.1 (Tolerance on thickness)	-
5.3.1.2 (Tolerance on width)	-
5.3.2, Table 1 (Nominal Film Thickness)	-
5.3.1.2 (Tolerance on width)	-
5.3.2, Table 1 (Nominal Film Thickness)	-
5.3.3 (Tensile Strength at Break)	-
5.3.4 (Elongation at Break)	-

Partial

-
-

IS/ISO 15761 (2002)

Steel gate, globe and check valves for sizes DN 100 and smaller, for petroleum and natural gas industries

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.2 (Flow Passage way)	-
5.3.1 (Wall Thickness)	-
5.3.2 (Wall Thickness)	-
5.3.3 (Wall Thickness)	-
5.4.2.1, Table4 (Socket Welding Ends, Diameter)	-
5.4.2.1, Table4 (Socket Welding Ends, Depth)	-
5.4.2.2, Table5 (Socket wall thickness)	-
5.4.2.3 (End to end dimension)	-
5.4.4.1 (Flange ends)	-
5.4.4.2 (Flange ends)	-
5.4.4.3,TABLE 6 (Flange ends)	-
5.4.5.1,Fig 1,Table 7 (Butt Welding Ends ,A)	-
5.4.5.1,Fig 1,Table 7 (Butt Welding Ends ,B)	-
5.4.5.1,Fig 1,Table 7 (Butt Welding Ends ,T)	-
5.4.5.2 (End to end dimension)	-
5.4.6.1 (Body Seat)	-
5.4.6.2 (Body Seat)	-
5.4.6.3 (Body Seat inside dia.)	-
5.7.1 (Stem)	-
5.7.2 (Stem)	-
5.8.1 (Stem nut or stem bushing)	-
5.9.1,Table 10 (Uncompressed packing height , hp)	-
5.9.2 (Surface Finish)	-
5.9.3 (Gland)	-
5.9.4 (Packing)	-
5.10.1 (Packing Retension)	-
5.10.2 (Packing Retension)	-
5.10.3 (Packing Retension)	-
5.10.4 (Packing Retension)	-
5.11.1 (Hand Wheel)	-
5.11.2 (Hand Wheel)	-
5.11.3 (Hand Wheel)	-

Partial

-
-

IS 1891 : Part 1 (1994)

Conveyor and elevator textile belting - Specification: Part 1 general purpose belting (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2 (Thickness)	-
8.1 (Cover Thickness)	-
8.2 (Carcass Thickness)	-
13.1 (Length)	-
13.2 (Width)	-
15 (Adhesion)	-

Partial

-
-

IS 808 (1989)

Dimensions for hot rolled steel beam, column, channel and angle sections (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7, 8, Table 2.1 (Dimensions, D)	-
7, 8, Table 2.1 (Dimensions, B)	-
7, 8, Table 2.1 (Dimensions, t)	-
7, 8, Table 2.1 (Dimensions, T)	-
7, 8, Table 2.1 (Dimensions, Flange Slope)	-
7, 8, Table 2.1 (Dimensions, R1)	-
7, 8, Table 2.1 (Dimensions, R2)	-
7, 8, Table 2.2 (Mass)	-
7, 8, Table 5.1 (Dimensions, AxB)	-

Partial

-
-

IS 1422 (1983)

Specification for cotton duck (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.2, Table 2, Sr. No. 1 (Scouring loss, Scoured or Dyed)	-
Cl 4.2, Table 2, Sr. No. 1 (Scouring loss, Grey)	-
Cl 4.2, Table 2, Sr. No. 2 (pH value )	-

Partial

-
-

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.2(a)-5.2 (Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-
4.2.2(b)-5.2 (Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-
4.2.3-5.3 (Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-
4.2.3-5.3 (Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-
4.2.4-5.3 (Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-
4.2.4-5.3 (Toys to be worn on the head-Full or partial moulded head masks-maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-
4.2.5-5.4 (Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-
4.2.5-5.4 (Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-
4.3-5.4 (Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-
4.3-5.4 (Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-
4.3 (Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-
4.4-5.4 (Toys intended to be entered by a child-rate of spread of flame)	-
4.5-5.5 (Soft-filled toys-rate of spread of flame )	-
4.5-5.5 (Soft-filled toys-Test for soft-filled toys )	-
4.1 (General)	-

Partial

-
-

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 - 5.24.2 ( Reasonably foreseeable abuse -Drop Test)	-
4.2 - 5.24.6.2 ( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys)	-
4.2 - 5.24.6.3 ( Reasonably foreseeable abuse -Tension test for pompoms)	-
4.2 - 5.24.6.4 ( Reasonably foreseeable abuse -Tension test for protective components)	-
4.2 - 5.24.6.5 ( Reasonably foreseeable abuse -Tension test for a projectile with a suction cup)	-
4.2 - 5.24.7 ( Reasonably foreseeable abuse -Compression test)	-
4.3.2 - 5.21 ( Expanding materials)	-
4.4.1 - 5.2 (Small parts-For children under 36 months)	-
4.4.2 - 5.2 (Small parts-For children 36 months and over but under 72 months )	-
4.5.1.2 - 5.3 (Shape, size and strength of certain toys-Squeeze toys, rattles, and certain other toys and components of toys-Test for shape and size of certain toys)	-
4.5.1.3 - 5.3 (Shape, size and strength of certain toys-Other toys or components of toys with nearly spherical, hemispherical, circular flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children under 18 months-Test for shape and size of certain toys)	-
4.5.1.4 - 5.3 (Shape, size and strength of certain toys-Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical, or dome-shaped ends intended for children 18 months and over but under 48 months-Test for shape and size of certain toys)	-
4.5.2 - 5.4 (Shape, size and strength of certain toys-Small balls-Small balls test)	-
4.5.3 - 5.5 (Shape, size and strength of certain toys-Pompoms-Test for pompoms)	-
4.7.1 - 5.9 (Points-Accessible sharp points-sharp-point test)	-
4.9 - c - 5.9 ( Metal wires and rods-Sharp Point test)	-
4.11.2.1(a) - 5.11.2 ( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables)	-
4.11.3.1(a) - 5.11.2 ( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables)	-
4.11.3.2 ( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords)	-
4.11.7 - 5.11.1 (Cords- Diameter of certain cords intended for children under 36 months-cords cross-sectional dimension)	-
4.11.8 - 5.11.5 (Cords- Self-retracting cords intended for children under 36 months-self-retracting cords)	-
4.16.2.2(a) - 5.13.2.1 (Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support)	-
4.16.2.2(a) - 5.13.2.2 (Enclosures-Closures-Lid support for toy chests and similar toys- After durability test for toy chest lids)	-
4.13.3 (Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys)	-
4.16.2.2(a) - 5.13.2.2 (Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support After durability test for toy chest lids)	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 1) (Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-
4.16.2.2(c) - 5.13.2.2 - 4.12.2 (a) - 5.22.3 (Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Other toys with folding mechanisms)	-
4.16.2.2(d) (Enclosures-Closures-Lid support for toy chests and similar toys)	-
4.11.5 - 5.11.2 (Cords-Cords on pull toys-free length)	-
4.18.3(b) - 5.15.1.3.3 (Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact)	-
4.18.3(d) - 5.15.2 (Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles)	-
4.18.3(b) - 5.15.1.3.3 (Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact)	-
4.18.4.1 - 5.20 (Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys)	-
4.18.4.3 - 5.15.1.3.3 (Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-kinetic energy per area)	-
4.18.4.3(a) (Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-
4.24(a) - 5.18 (Toys containing a heat source-determination of temperature increases)	-
4.25 - 5.19 (Liquid-filled toys-leakage of liquid-filled toys)	-
4.25 (Liquid-filled toys)	-
4.2 - 5.24.2 ( Reasonably foreseeable abuse -Drop Test)	-
4.2 - 5.24.6.2 ( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys)	-
4.2 - 5.24.6.3 ( Reasonably foreseeable abuse -Tension test for pompoms)	-
4.2 - 5.24.6.4 ( Reasonably foreseeable abuse -Tension test for protective components)	-
4.2 - 5.24.6.5 ( Reasonably foreseeable abuse -Tension test for a projectile with a suction cup)	-
4.2 - 5.24.7 ( Reasonably foreseeable abuse -Compression test)	-
4.2 - 5.24.8.2 ( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent)	-
4.2 - 5.24.8.3 ( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent)	-

Partial

-
-

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 Table-1 (Cu)	-
8.1 Table-1 (Mg)	-
8.1 Table-1 (Si)	-
8.1 Table-1 (Fe)	-
8.1 Table-1 (Mn)	-
8.1 Table-1 (Zn)	-
8.1 Table-1 (Cr)	-

Partial

-
-

IS 7904 (2018)

High carbon steel wire rods - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1,(Clauses 5.1 and 7.2) (Carbon)	-
Table-1,(Clauses 5.1 and 7.2) (Sulphor)	-
Table-1,(Clauses 5.1 and 7.2) (Phosphorous)	-
Table-1,(Clauses 5.1 and 7.2) (Manganese)	-
Table-1,(Clauses 5.1 and 7.2) (Silicon)	-
Table-1,(Clauses 5.1 and 7.2) (Chromium)	-
Table-1,(Clauses 5.1 and 7.2) (Nickel)	-
Table-1,(Clauses 5.1 and 7.2) (Molybdenum)	-
Table-1,(Clauses 5.1 and 7.2) (Copper)	-
Table-1,(Clauses 5.1 and 7.2) (Nitrogen)	-
Table-1,(Clauses 5.1 and 7.2) (S+P)	-
Cl 9 (Dimensions & tolerances) ()	-

Partial

-
-

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2 AND AS PER IS 513 (CARBON)	-
6.2 AND AS PER IS 10748 (SULPHUR)	-
6.2 AND AS PER IS 10748 (PHOSPHORUS)	-
6.2 AND AS PER IS 10748 (MANGANESE)	-

Partial

-
-

IS 8931 (1993)

copper alloy fancy single taps, combination tap assembly and stop valves for water services

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (NOMINAL SIZES)	-
Cl 6.7 (Waterway)	-
Cl 6.9 (Body Seat)	-
Cl 6.10 (Bonnet assembly)	-
Cl 6.11 (Gland Packaging)	-
Cl 6.12 (Flanges)	-
Cl 6.13 (Knob)	-
Cl 7.1 (Thickness)	-
Cl 7.2 (Body)	-
Cl 7.3 (Bonnet Assembly)	-
Cl 7.3.3 (Washer Plate)	-
Cl 7.3 (Bonnet Assembly)	-
Cl 8 (Finish)	-

Partial

-
-

IS 737 (2008)

Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0 (Freedom from defects)	-
7 Table-2 (Tensile Strength)	-
7 Table-2 (Elongation)	-
7 Table-2 (0.2 % Proof Stress)	-
7 Table-2 (Bend Test)	-
6 Table-1 (Cu)	-
6 Table-1 (Mg)	-
6 Table-1 (Si)	-
6 Table-1 (Fe)	-
6 Table-1 (Mn)	-
6 Table-1 (Zn)	-
6 Table-1 (Cr)	-
6 Table-1 (Cu+Si+Fe)	-
6 Table-1 (Cu+Si+Fe+Mn+Zn)	-
6 Table-1 (Cu+Mg+Si+Fe+Mn+Zn)	-
6 Table-1 (Cr+Mn)	-

Partial

-
-

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4 (Freedom from Defects)	-
Cl. 5.1, Table 2 (0.2 Percent proof stress- IS 1816)	-
Cl. 5.1, Table 2 (Tensile Strength- IS 1816)	-
Cl. 5.1, Table 2 (Elongation on 50 mm or 5.65√So Gauge Length)	-
Cl. 0.4, 5.1, Table 1 (Copper- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Magnesium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Silicon- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Iron- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Zinc- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Chromium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Cr+ Mn- IS 504 or by any other suitable instrumental method)	-

Partial

-
-

IS 3444 (1999)

Corrosion resistant high alloy steel and nickel base castings for general applications - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

IS 10350 (2020)

Powder Hair Dyes — Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
Clause 4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 2)	-
Clause 4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 3)	-
4.5 Table 1 (pH, type 1 and 2)	-
4.5 Table 2 (pH, Type 3)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 1 (Heavy metals (as Pb), for all types)	-
4.1 (description)	-

Partial

-
-

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 Table 1 (Cu)	-
8.1 Table 1 (Pb)	-
8.1 Table 1 (Fe)	-
8.1 Table 1 (Zn)	-
10.1 (Mercurous Nitrate Test)	-
7.0 (Dimension and Tolerances)	-
9.1 Table-2 (Tensile Strength)	-
9.1 Table-2 (Elongation)	-
9.2 (Vickers Hardness)	-

Partial

-
-

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List