BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List

Reset

366 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

331

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

complete Cat 01(Except melt flow, vicat, bending)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Insulation)	-
6.1 (Flexibility class)	-
6.2 (Compactness)	-
6.2 (No of strands)	-
6.2 (Surface)	-
6.3 (Protective barrier)	-
6.4 (size of street lighting conductor)	-
6.5 (Size of messenger conductor )	-
6.6 (Joints in messenger conductor )	-
6.6 (Direction of outer layer)	-
7.2 ( Thickness of insulation)	-
7.3 (Tolerance on thickness of insulation )	-
7.4 (Aplication of the insulation )	-
7.5 (Colour of the insulation )	-
8.1 (Core identification)	-
8.2 (Core identification)	-
8.3 (Identification by other means)	-
9.1 (Assembly (Laying up))	-
9.2 (Assembly (Laying up))	-
9.3 (Direction of lay)	-
10.1 a) i) (Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-
10.1 a) ii) (Wrapping test - 10810: Part 3)	-
10.1 a) iii) (Resistance test - IS10810: Part 5)	-
10.1 b) i) (Test on messenger conductor: Breaking load - IS 10810: Part 2)	-
10.1 b) ii) (Test on messenger conductor: Elongation test - Cl 11.3)	-
10.1 b) iii) (Test on messenger conductor: Resistance test - IS 10810: Part 5)	-
10.1 c) i) (Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-
10.1 c) i) (Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-
10.1 c) ii) (Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-
10.1 c) ii) (Ageing in air oven : Elongation variation- IS 10810: Part 11)	-
10.1 c) iii) (Hot set test: Elongation under load - IS 10810: Part 30)	-
10.1 c) iii) (Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-
10.1 c) iv) (Shrinkage test : Shrinkage - 10810:Part 12)	-
10.1 c) iv) (Shrinkage test : Crack Observed - 10810:Part 12)	-
10.1 c) v) (Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-
10.1 d) i) (Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-
10.1 d) i) (Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-
10.1 f) (Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-
10.1 f) (Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-
10.1 g) (High voltage test - IS10810:Part 45)	-

Partial

-
-

332

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Partial

-
-

333

IS 1148 (2009)

Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Partial

-
-

334

IS 11169 : Part 2 (1989)

Steels for cold heading/cold extrusion applicationsspecification: Part 2 stainless steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1,6.2 Table 2 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1,6.2 Table 2 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1,6.2 Table 2 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1,6.2 Table 2 (Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1,6.2 Table 2 (Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1,6.2 Table 2 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
8.2, table 5 (i) Yield stess/.2% Proof stress, Mpa)	-
8.2, table 5 (ii)Ultimate Tensile Strength, Mpa)	-
8.2, table 5 (iii)Elongation, %)	-
8.1, Table 4 (iv) Reduction in area)	-

Partial

-
-

335

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (TYPES)	-
4.2 (Construction)	-
4.3.1 (Bottom Seam)	-
4.3.1 ( The two rows of stitches shall be separated from each other)	-
4.3.1 ( The outer stitch)	-
4.3.1 (Stitches pass through a minimum of six layers of the fabric. )	-
4.3.1 (The number of stitches/dm)	-
4.3.2 (Mouth)	-
4.4 and Table 1 i (Capacity)	-
5.2 and Table 1 ii a (Dimensions Inside Length)	-
5.2 and Table 1 ii b (Dimensions Inside Width)	-
5.2 and Table 1 iii (Ends per dm )	-
5.2 and Table 1 iv (Picks per dm )	-
5.1 and Table 1 v (Mass of sack )	-
5.2 and Table 1 vi a (Average breaking strength of fabric Lengthwise )	-
5.2 and Table 1 vi b (Average breaking strength of fabric Widthwise )	-

Partial

-
-

336

IS 1061 (2017)

Disinfectant fluids, phenolic type - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 (chem) (Composition and Description)	-
4.1.2 (Chem) (Composition and Description)	-
4.2 (Chem) (Stability after Dilution)	-
4.4 (Chem) (Mercury Compounds)	-
4.6 (Chem) (Detection of Phenolic Compounds)	-
4.5 (Chem) (Stability on Storage)	-

Partial

-
-

337

IS 10631 (1983)

Specification for stainless steel for welding electrode core wire

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table 1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6 (FREEDOM FROM DEFECTS)	-

Partial

-
-

338

IS 16353 (2015)

Portland Cement Clinker - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 5 Table 1 (Ratio of percentage of lime to percentages of silica, alumina and iron oxide)	-
Clause 5 Table 1 (Ratio of percentage of alumina to that of iron oxide,)	-
Clause 5 Table 1 (C3S, percent by mass)	-
Clause 5 Table 1 (C3A, percent by mass)	-
Clause 5 Table 1 (C3S+C2S, percent by mass)	-
Clause 5 Table 1 (Total sulphur content calculated as sulphuric anhydride (SO3))	-
Clause 5 Table 1 (Free lime)	-
Clause 5 Table 1 (Chloride content)	-
Clause 5 Table 1 (Magnesia)	-
Clause 5 Table 1 (Alkali content)	-
Clause 5 Table 1 (Total loss on ignition)	-
Clause 5 Table 1 (Insoluble residue)	-
6.1 Table 2 iii) c) IS 4031 (Part 6) (Compressive Strength at 672±4 h)	-
6.1 Table 2 iii) b) IS 4031 (Part 6) (Compressive Strength at 168±2 h)	-
6.1 Table 2 iii) a) IS 4031 (Part 6) (Compressive Strength at 72±1 h)	-
6.1 Table 2 ii) a) IS 4031 (Part 5) (Initial Setting time)	-
6.1 Table 2 ii) b) IS 4031 (Part 5) (Final Setting time)	-
6.1 Table 2 i) b) IS 4031 (Part 3) (Soundness by Autoclave test method)	-
6.1 Table 2 i) a) IS 4031 (Part 3) (Soundness by Le-Chatelier method)	-
6.1 IS 4031(Part 2) (Fineness)	-

Partial

-
-

339

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Sulphur -IS 228 or method specified in relevant ISO standard)	-
Cl.4 (Phosphorus -IS 228 or method specified in relevant ISO standard)	-
5.2 (Tensile Strength, Mpa)	-
5.2 (Elongation, %)	-
5.3 (Bend Test-1599)	-
7.1 (Freedom from defects)	-
8.2 (Width)	-
8.2 (Thickness)	-

Complete

-
-

340

IS 1011 (2002)

Biscuits - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (General Requirement)	-
6.3 Table 2 i (Moisture)	-
6.3 Table 2 ii (Acid insoluble ash (on dry basis))	-
6.3 Table 2 iii (Acidity of extracted fat (as oleic acid))	-

Complete

-
-

341

IS 299 (2012)

Alumino - Ferric - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1 (i) Table 1 ( Insouble matter, Grade 1, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 2, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 3, A-3)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 1, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 2, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 3, A-4)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 1, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 2, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 3, A-5)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 1, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 2, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 3, A-6)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 1, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 1, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 2, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 3, A-7)	-

Partial

-
-

342

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

complete cat 01(except water absorption above 25sqmm)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (CONDUCTOR: MATERIALS)	-
4 (INSULATION : MATERIALS)	-
5.1 (FILLER AND INNER SHEATH)	-
5.2 (FILLER AND INNER SHEATH)	-
6 (ARMOURING)	-
7 (OUTER SHEATH)	-
8.1 (CONDUCTOR: CONSTRUCTION)	-
8.2 (PROTECTIVE BARRIER)	-
8.3 (SIZE OF NEUTRAL CONDUCTOR)	-
9.2 (Thickness of Insulation - Average)	-
9.3 (Thickness of Insulation - Minimum)	-
9.4 (Application of Insulation)	-
10.1 (Core Identification)	-
10.2 (Core Identification- Neutral)	-
10.3 (Core Identification by number )	-
10.4 (Core Identification by number - Neutral )	-
11 (LAVING UP OF CORES)	-
12.1 & 12.2 (Inner sheath : Application)	-
12.3 (Thickness of Inner Sheath)	-
13.1 (Armouring: Application)	-
13.1.3 (Armouring: Direction of Lay )	-
13.2 (Type of armour )	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (Armour: Joint)	-
13.5 (Armouring : Resistance Test)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (Outer Sheath : Application)	-
14.2 (Colour of outer sheath)	-
14.3 (Thickness of outer sheath - AVERAGE)	-
14.3 (Thickness of outer sheath - minimum)	-
15.1 a) i) (Annealing Test ( For copper wire ) )	-
15.1 a) ii) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) ii) (Tensile test (for aluminium) - After stranding )	-
15.1 a) iii) (Wrapping test (for aluminium))	-
15.1 a) iv) (Resistance test - Main conductor)	-
15.1 a) iv) (Resistance test - Neutral conductor)	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 e) v) (Sheath : Hot deformation)	-
15.1 e) vi) (Sheath : Heat shock test)	-
15.1 e) vii) (Sheath : Thermalstability)	-
15.1 f) (INSULATION RESISTANCE TEST : Volume resistivity )	-
16.2 (HIGH VOLTAGE TEST )	-
16.3 (FLAMMABILITY TEST : Period of Burning )	-
16.3 (FLAMMABILITY TEST : Unaffected length )	-
17.1 (Manufacturer'. ldeadentificatioa)	-
17.2 (cable Indentification )	-
17.3 (cable Code )	-

Partial

-
-

343

IS 3074 (2013)

Steel tubes for automotive purposes - Specification (Third Revision)

- View breakup
Rs.3750/- for CDS-1, CDS-2, CDS-3, CDS-4, CDS-5, Rs.4720/- for CDS-6, Rs.6750/- for CDS-7 & CDS-8, Rs.6750/- for CDS-9. Rs.3750/- for ERW/HFIW (ERW-1, ERW-2, ERW-3). Rs.4200/- for Mechanical testing charges.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7, 20,Table 1,2,4 &6 ( C)	-
7, Table 1,2,4 &6 (Mn)	-
7, Table 1,2,4 &6 (S)	-
7, Table 1,2,4 &6 (P)	-
7, Table 1,2,4 &6 (Si)	-
7, Table 1,2,4 &6 (Ni)	-
7, Table 1,2,4 &6 (Cr)	-
7, Table 1,2,4 &6 (Mo)	-
8.2,15,17,22, Table 3,5 &7 (Tensile Tests,IS 1608 Part 1)	-
8.3,18, (Flattening Test)	-
6 (STRAIGHTNESS)	-

Partial

-
-

344

IS 1015 (2000)

Leather pump buckets and seat valves made from vegetable taned leather - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.3- Table 1 (Manufacture)	-
4.4 (Cracking Test )	-
5.2 (Manufacture)	-
5.4 (Performance Test)	-
6.1 (Dimensions)	-
6.2 (Performance Test)	-

Partial

-
-

345

IS 398 : Part 5 (1992)

Aluminium conductor for overhead transmission purposes - Specification: Part 5 aluminium conductors - Galvanized steel - Reinforced for extra high voltage (400 KV And Above) (First Revision)

Except corona, RI, Breaking load of complete conductor

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (elec) (Freedom from defects)	-
13.2 (mech) (Visual Examination)	-
13.3 Table-1 (mech) (Diameter-Aluminium wires)	-
13.3 Table-2 (mech) (Diameter-Galvanized Steel wires)	-
13.5.2 Table 1 (mech) (Breaking Load of Aluminium Wires Before Stranding)	-
13.5.2 Table 2 (mech) (Breaking Load of Steel Wires Before Stranding)	-
13.5.2 Table 1 (mech) (Breaking Load of Aluminium Wires After Stranding)	-
13.5.2 Table 2 (mech) (Breaking Load of Steel Wires After Stranding)	-
13.6.1 (mech) (Ductility by Torsion Test before stranding)	-
13.6.1 (mech) (Ductility by Torsion Test after stranding)	-
13.6.2 (mech) (Ductility by Elongation Test before stranding)	-
13.6.2 (mech) (Ductility by Elongation Test after stranding)	-
13.7.1 (mech) (Wrapping Test Aluminium Wires Before Stranding)	-
13.7.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.7.2 (mech) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.7.2 (mech) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.9.2 (chem) (Mass of Zinc coating)	-
13.9.2 (chem) (Uniformity of Zinc coating)	-
13.4 Table-4 (mech) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.4 Table-4 (mech) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.4 Table-4 (mech) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors eith 3 Aluminium Wire Layers)	-
13.4 Table-4 (mech) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.2 (elec) (Visual Examination)	-

Partial

-
-

346

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Complete

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor )	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-
11 (Packing and Marking)	-
7.1 Table-1 (Dimensional measurement of wires)	-
9.1 (Stranding)	-

Partial

-
-

347

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Complete

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.2, Table-1 (Measurement of diameter of individual aluminium wire)	-
12.3, Table-1 (Breaking load before stranding)	-
12.3, Table-1 (Breaking load after stranding)	-
12.4 (Wrapping test)	-
12.5, Table 1 (Resistance test)	-
12.6, Table 3 (Measurement of lay ratio)	-
9.3 (Stranding)	-
6 (Freedom from defects)	-
12.6, Table 3 (Measurement of lay ratio)	-
12.5, Table 1 (Resistance test)	-

Partial

-
-

348

IS 1417 (2016)

Gold and gold alloys, jewellery/ artefacts - Fineness and marking - Specification (Fourth Revision)

22K 916 , 18K 750 , 14 K 585

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Fineness/ Gold Content in parts per thousand, percent)	-
4.1.1 (b) (Cadmium, Percent)	-
4.1.1 (b) (Each of Platinum Group Metals, Percent)	-
4.1.1 © (Presence of Iridium, Ruthenium & Cadmium)	-
4.1 (Fineness/ Gold Content in parts per thousand, percent)	-
4.1 (Fineness/ Gold Content in parts per thousand, percent)	-

Partial

-
-

349

IS 13428 (2005)

Packaged natural mineral water specification (Second Revision)

- View breakup
All except Radio Active Residues (RAR)- Rs 19200.00, All except Pesticide Residues (PRs) & RARs- Rs. 13900.00, All except Micro, PRs & RARs- Rs. 8750.00, Only Micro- Rs. 5900.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1.1 (Escherichia coli(or thermotolerant bacteria))	-
6.1.2 (Coliform , bacteria)	-
6.1.3 (Faecal Streptococci )	-
6.1.3 (Staphylococcus Aureus)	-
6.1.4 (Sulphite Reducing Anaerobes )	-
6.1.5 (Pseudomonas Aeruginosa )	-
6.1.6 (Yeast and Mould )	-
6.1.7 (Salmonella )	-
6.1.7 (Shigella)	-
6.1.8 (Vibrio cholera )	-
6.1.8 (Vibrio parahemolyticus)	-
6.2 Table-1 i (Colour)	-
6.2 Table-1 ii (Odour)	-
6.2 Table-1 iii (Taste)	-
6.2 Table-1 iv (Turbidity)	-
6.2 Table-1 v (Total dissolved solids)	-
6.2 Table-1 vi (pH)	-
6.2 Table-2 i (Nitrate (as NO3))	-
6.2 Table-2 ii (Nitrite (as NO2))	-
6.2 Table-2 iii (Sulphide (as H2S))	-
6.2 Table-2 iv (Manganese (as Mn))	-
6.2 Table-2 v (Copper (as Cu))	-
6.2 Table-2 vi (Zinc (as Zn))	-
6.2 Table-2 vii (Flouride (as F))	-
6.2 Table-2 viii (Barium (as Ba))	-
6.2 Table-2 x (Borates (as B))	-
6.2 Table-2 xii (Chloride (as Cl))	-
6.2 Table-2 xiii (Sulphate (as SO4),)	-
6.2 Table-2 xiv (Magnesium (as Mg))	-
6.2 Table-2 xii (Chloride (as Cl))	-
6.2 Table-2 xv (Calcium (as Ca))	-
6.2 Table-2 xvi (Sodium (as Na))	-
6.2 Table-2 xvii (Alkalinity (as HCO3))	-
6.2 Table-2 xviii (Selenium (as Se))	-
6.2 Table-2 xix (Mineral Oil)	-
6.2 Table-2 xx (Phenolic compounds (as C6H5OH))	-
6.2 Table-2 xxi (Anionic surface active agents (as MBAS))	-

Partial

-
-

350

IS 17404 (2020)

Electrogalvanized Hot Rolled and Cold Reduced Carbon Steel Sheets and Strips ” Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (As per IS 1079, IS 5986, IS 513(pt-1 & 2)) (C -IS 228)	-
7.1 (As per IS 1079, IS 5986, IS 513(pt-1 & 2)) (Mn - IS 228)	-
7.1 (As per IS 1079, IS 5986, IS 513(pt-1 & 2)) (P - IS 228 )	-
7.1 (As per IS 1079, IS 5986, IS 513(pt-1 & 2)) (S - IS 228)	-
7.1 (As per IS 1079, IS 5986, IS 513(pt-1 & 2)) (N - IS 228)	-
7.1 (As per IS 1079, IS 5986, IS 513(pt-1 & 2)) (Si - IS 228)	-
7.1 (As per IS 1079, IS 5986, IS 513(pt-1 & 2)) (Cu - IS 228)	-
9.1, 9.1.1-Table 1 (Coating Mass per Surface, Min - IS 12860 & IS 6745)	-
9.1, 9.1.1-Table 1 (Coating Mass per Surface, Max - IS 12860 & IS 6746)	-

Partial

-
-

351

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1, Table 1 - i (Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-
Cl. 6.1, Table 1 - ii (Silicon dioxide (SiO2) - IS 1727)	-
Cl. 6.1, Table 1 - iv (Magnesium oxide (MgO) - IS 1727)	-
Cl. 6.1, Table 1 - v ( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-
Cl. 6.1, Table 1 - vi ( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-
Cl. 6.1, Table 1 - vii ( Total Chlorides - IS 4032)	-
Cl. 6.1, Table 1 - viii ( Loss on ignition - IS 1727)	-
Cl. 6.2 (Moisture content of the fly ash when supplied in dry condition - Annex D)	-

Partial

-
-

352

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 10.3 (UTM)	-
Cl 11.3 (Press)	-
Cl 12 (Sudden Load Applied)	-
Cl 15 (Length, Width & Thickness)	-
Cl 15 (Length, Width & Thickness)	-
Cl 15 (Length, Width & Thickness)	-
Clause - 5, 8.1 & 8.2 (E650, SILICON)	-
Clause - 5, 8.1 & 8.2 (E250, CARBON)	-
Clause - 5, 8.1 & 8.2 (E250, SULPHUR)	-
Clause - 5, 8.1 & 8.2 (E250, PHOSPHURS)	-
Clause - 5, 8.1 & 8.2 (E250 ,MANGANESE)	-
Clause - 5, 8.1 & 8.2 (E250, NITROGEN)	-
Clause - 5, 8.1 & 8.2 (E250, SILICON)	-
Clause - 5, 8.1 & 8.2 (E250, CARBON +EQUIVELENT )	-

Partial

-
-

353

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Mean Outer Diameter of Pipe)	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Outer Diameter at any point )	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Mean Outer Diameter over Connection)	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Wall thickness)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe, Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe , Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Outer Diameter at any point , Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Outer Diameter at any point, Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter over Connection)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Max)	-
7.4 Table 8 & 9 Fig 1 (Effective length, l2)	-
7.4 Table 8 & 9 Fig 1 (Segmental length, l3)	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A (THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-
8.4 (Sealing rings - Hardness)	-
9.3 (Density IS 12235 (Part 14))	-
9.4 and Table 14 (Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-
9.5 (Tensile Strength IS 12235(Part 13))	-
9.6 (Vicat Softening Temperature IS 12235 (Part 2).)	-
9.1 ( Visual Appearance)	-
9.2 (Internal Diameter)	-
7.4 Table 8 & 9 Fig 1 (Segmental length, l3)	-

Partial

-
-

354

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.3 (Dimensional Requirements - Length - 8.1.4)	-
7.3 (Dimensional Requirements - Width - 8.1.4)	-
7.3 (Dimensional Requirements - Thickness - Annexure E)	-
7.3 (Dimensional Requirements - Variation in thickness - Annexure E)	-
7.3 (Dimensional Requirements - Squareness - Annexure D)	-
7.3 (Dimensional Requirements - Edge Straightness - Annexure D)	-
9.2.5 (Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of elasticity - AVERAGE - Annexure K)	-
9.2.5 (Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of rupture - AVERAGE - Annexure K)	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-
9.2.3 (Adhesion of Plies - Annexure H)	-
9.2.4 (Mycological Test [for MR grade only] - Annexure J)	-
9.2.1 (Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Delamination - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
8.1.3, 6.3.3, IS 1328 (Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-
8.1.3, 6.3.3, IS 303 (Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-
9.2.6 (Spot test - Annexure L)	-

Complete

-
-

355

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. Variation)	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Minimum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Average Thickness)	-
7.2.1 (DIMENSIONS-Socket)	-
10.2 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-
10.4 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-
10.5 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-
10.6 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-
11.2 (Resistance to External Blows at 0°C)	-
10.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.1.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-
Clause 10.7 (Sulphated Ash Content)	-

Partial

-
-

356

IS 2202 : Part 1 (1999)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.1 (Height - IS 4020 (Pt-2))	-
11.1 (Width- IS 4020 (Pt-2))	-
11.1 (Thickness - IS 4020 (Pt-2))	-
11.1 (Variation in thickness - IS 4020 (Pt-2))	-
11.1 ( Squareness Test - IS 4020 (Pt-2))	-
9.1 (Workmanship & finish - IS 2202(Pt-1))	-
9.2 (Workmanship & finish - IS 2202(Pt-1))	-
9.3 (Workmanship & finish - IS 2202(Pt-1))	-
11.12 (End Immersion Test - IS 4020(Pt-13))	-
11.13 (Knife Test - IS 4020(Pt-14))	-
11.14 (Glue Adhesion Test - IS 4020(Pt-15))	-

Partial

-
-

357

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

- View breakup
Rs. 14700/- excluding test on handles and chemical tests.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Capacity )	-
5.2 (Safety Relief Device)	-
6.1.1 (Pressure Regulating Device)	-
8.1 (Air Pressure Test)	-
8.2 (Proof Pressure Test)	-
8.3 (Operating Test for Pressure Regulating Device)	-
8.4 (Test for Safety Pressure Relief Device)	-
8.5 (Bursting Pressure Test)	-
8.6.1 (Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-

Partial

-
-

358

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Complete up to 100sqmm(Except stress strain)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires Before Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires After Stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
10 (mech) (Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires Before Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires Before Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires After Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires After Stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.4.2 (elec) (Ductility by Elongation Test before stranding)	-
13.4.2 (elec) (Ductility by Elongation Test after stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires Before Stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire before Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
13.7.2 (chem) (Mass of Zinc coating)	-
13.7.2 (chem) (Uniformity of Zinc coating)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-
13.8 Table-4 (mech) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.7.2 (chem) (Mass of Zinc coating)	-
13.7.2 (chem) (Uniformity of Zinc coating)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-

Partial

-
-

359

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-
Cl 7.2 (Weight)	-
Cl. 8.1 Table 3 (Yield Stress (YS))	-
Cl. 8.1 Table 3 (Tensile Strength (TS))	-
Cl. 8.1 Table 3 (TS/YS ratio)	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
4.1 (Sulphur and phosphorous)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
Cl. 9.3, Table 4 (Bend Test )	-
Cl.9.4 & Cl. 9.4.1 (Rebend test)	-
8.18.1 Table 3 (Total elongation at maximum force)	-

Partial

-
-

360

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Complete for Cat 01(up to 400sq.mm)Except optional test

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
5.2 (MATERIALS : FILLER AND INNER SHEATH)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
6.2 (MATERIALS : ARMGURING)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.1 (INSULATION )	-
9.2 (INSULATION : Thickness of Insulation)	-
9.3 (INSULATION :Tolerance on Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
11.1 (LAYING UP OF CORES)	-
11.2 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
12.3.1 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.1.4 (ARMOURING : Application)	-
13.2 (ARMOURING : Type of Armour)	-
13.2.1 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.2 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
16.2 (DETAILS OF TESTS : High Voltage Test at Room Temperature)	-
16.3.2 (High Voltage Test ( Water Immersion Test ) : d.c. Test)	-
16.3.1 (High Voltage Test ( Water Immersion Test ) : a.c. Test)	-
15.4 c) (Armour resistance test ( for other than mining cables ).- Optional test )	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.2.1 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
13.3 (Armouring : Dimensions -Formed wire )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
16.4 (Flammability Test)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
3.1 (MATERIALS : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-

Partial

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Office Laboratory (EROL)

Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W, Kankurgachi, Kolkata, Kolkata, West Bengal, 700054

- [email protected]

Scope List