BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- [email protected]

Scope List

Reset

773 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

121

IS 16088 (2012)

Chlorinated polyvinyl chloride (CPVC) pipes for automatic sprinkler fire extinguishing system - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.5 IS 12235(Part 2) (Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-
9.3 (Reversion test : )	-
9.5 (Density)	-
8 (Pipe Ends)	-
7.1.1 IS 12235 (Part 1) Table 1 (Mean outside Diameter)	-
7.1.1.1 IS 12235 (Part 1) Table 1 (Outside Diameter at any point)	-
7.1.2 (Wall Thickness)	-
10.3 (Flattening)	-
10.4 (Tensile Strength)	-
9.1 (Visual Appearance)	-
5 (Classification of pipes)	-

Partial

-
-

122

IS 928 (1984)

Specification for fire bells (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

123

IS 6046 (1982)

Specification for gypsum for agricultural use (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 (Sodium Content)	-
2.2 (Calcium Sulphate Content)	-
2.1 (Fineness)	-
2.2 (Sodium Content)	-
2.2 (Calcium Sulphate Content)	-

Complete

-
-

124

IS 14268 (2017)

Uncoated stress relieved low relaxation seven - Wire (Ply) strand for prestressed concrete - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 6.2.3 (Elongation)	-
Clause 6.2.2- Table 1 (Maximum Breaking Strength of Strand)	-
Clause 6.1- Table 2 (Nominal Mass of the strand)	-
Clause 6.1- Table 2 (Nominal Area of the strand)	-
Clause 6.1- Table 2 (Nominal Dia of the strand)	-
Clause 5 (Class)	-
Clause 4.5 (Workmanship and finish)	-
Clause 4.3 (Joints)	-
Clause 4.2 (Length of Lay)	-
Clause 4.2 (Percentage Difference in diameter of centre wire and surrounding wire)	-
Clause 4.1.3 (Wire Description)	-
Clause-4.1, 4.1.1, 4.1.2 (SULPHUR)	-
Clause-4.1, 4.1.1, 4.1.2 (PHOSPHURS)	-
Clause-4.1, 4.1.1, 4.1.2 (SULPHUR)	-
Clause-4.1, 4.1.1, 4.1.2 (PHOSPHURS)	-

Partial

-
-

125

IS 916 (2000)

Square tins for solid products - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Capacity)	-
4.2 (Dimension and Tolerances)	-
4.3.1 (Nominal Thickness)	-
4.3.2 (Handle wire diameter)	-
4.3.2 (Handle wire material)	-
4.4.1 (Body)	-
4.4.2 (Sides)	-
4.4.3 (Top and Bottom)	-
4.4.4 (Top and Bottom embossing)	-
4.4.5 (Handle)	-
4.4.6 (Closure)	-
4.4.7 (Supply condition)	-
4.4.8 (Internal Finish)	-
4.4.9 (External Treatment)	-
5.1 (Air-Pressure Test)	-
5.2 (Handle Pull Test)	-

Complete

-
-

126

IS 9282 (2002)

Wire ropes and strands for suspension bridges - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1 ( MATERIAL- Requirements of Wire -Dimensional Limits and Tolerances )	-
4.2.2 (Tensile Test)	-
4.3 (Elongation Test )	-
4.5.1 (Galvanizing)	-
4.5.2 (Wrap Tes)	-
5 (GENERAL REQUIREMENTS General requirements shall be according to IS 6594.)	-
6.1 (JOINTS)	-
7.1 ( DIRECTION OF LAY)	-
8.1 (LENGTH OF LAY)	-
10. table 1 to 11 (MINIMUM BREAKING FORCE )	-
Clasuse - 4 ( CARBON)	-
Clasuse - 4 (SULPHUR)	-
Clasuse - 4 (PHOSPHURS)	-
Clasuse - 4 (MANGANESE)	-
Clasuse - 4 (SILICON)	-
Clasuse - 4 ( ALUMINIUM)	-
Clasuse - 4 (NITROGEN)	-
Clasuse - 4 (Nickel)	-
Clasuse - 4 (Chromium)	-
Clasuse - 4 (Molybdenum)	-
Clasuse - 4 (NIOBIUM)	-
Clasuse - 4 (VANADIUM)	-
Clasuse - 4 (TITANIUM)	-

Partial

-
-

127

IS 4109 (1967)

Specification for kadahies

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2 (Materials)	-
3 (a) Round Shape / Bowl Shape)	-
3 (b) Nominal dia. at top D1 mm)	-
3 (c) Nominal overall Height H1 mm)	-
3 (d) Thickness at bottom mm Min)	-
4 (Manufacture and Workmanship)	-
6 (Test)	-

Complete

-
-

128

IS 285 (1992)

Laundry soaps - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4, Table-1 (ix) Type-2 (Built soap) Gr-2 (LSD/NSD content, IS 4955)	-
5.4, Table-1 (viii) Type-2 (Built soap) Gr-1 & Gr-2 (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (viii) Type-1 (Pure soap) (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (vii) Type-1 (Pure soap) (Glycerol, IS 286)	-
5.4, Table-1 (v) Type-2 (Built soap) Gr-1 (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (v) Type-1 (Pure soap) (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (iv) (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.4, Table-1 (iii) (Unsaponified fatty matter, IS 286)	-
5.4, Table-1 (ii) (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-2 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-1 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-1 (Pure soap) (Total fatty matter, IS 286)	-
5.3 (Odour and Lathering Properties, IS 286)	-
5.4, Table-1 (ix) Type-2 (Built soap) Gr-2 (LSD/NSD content, IS 4955)	-
5.4, Table-1 (viii) Type-2 (Built soap) Gr-1 & Gr-2 (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (viii) Type-1 (Pure soap) (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (v) Type-2 (Built soap) Gr-1 (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (v) Type-1 (Pure soap) (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (iv) (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.4, Table-1 (iii) (Unsaponified fatty matter, IS 286)	-
5.4, Table-1 (ii) (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-2 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-1 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-1 (Pure soap) (Total fatty matter, IS 286)	-
5.3 (Odour and Lathering Properties, IS 286)	-

Complete

-
-

129

IS 9165 : Part 2 (1992)

Surgical instruments - Needles, suture: Part 2 eyed needles - Sizes, shapes and dimensions

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1, Table 1 (Dimensions of Eyed Suture Needles)	-
3.1, Table 1 (Dimensions of Eyed Suture Needles)	-

Complete

-
-

130

IS 12650 (2018)

Textiles – Jute bags for packing 50 kg foodgrains – Specification (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4-4.2 (Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-
4-4.3 (Manufacture-Safety Stitch-The number of safety union stitches per decimetre shall be10 ± 1.)	-
4-4.1 (MANUFACTURE- The bags shall be made from single piece of twill weave jute sacking of uniform construction having nominal mass of 579 g/m2 as given below with warp running along the length of the bag:)	-
4-4.2 (Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-
4-4.3 (Manufacture-Safety Stitch-The number of safety union stitches per decimetre shall be10 ± 1.)	-
4-4.1 (MANUFACTURE- The bags shall be made from single piece of twill weave jute sacking of uniform construction having nominal mass of 579 g/m2 as given below with warp running along the length of the bag:)	-
4-4.1-a) (MANUFACTURE)	-
4-4.1-b) (MANUFACTURE)	-
4-4.1 (MANUFACTURE)	-
4-4.2 (Manufacture)	-
4-4.3 (Manufacture-Safety Stitch )	-
4-4.4 (Manufacture-Hemming at the Mouth )	-
4-4.5 (Manufacture- Freedom from Defects )	-
5-5.1-Table 1-Sr. no. i) (SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 a) Out side Length , cm 94 (For both type A & Type B) Tolerance + 4 / -0 cm)	-
5-5.1-Table 1-Sr. no. i) (SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 b) Outside width, cm 57 (For both type A & Type B) Tolerance + 4 / -0 cm)	-
5-5.1-Table 1-Sr. no.i i) (SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Ends/dm Type A 46 + 2 /Type B 76 + 4 / -3)	-
5-5.1-Table 1-Sr. no.iii) (SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Picks/dm Type A 50 (2 x 25) / Type B 28 + 2)	-
5-5.1-Table 1-Sr. no.iv) (SPECIFIC REQUIREMENTS-Cl. 8.5.2 of IS 9113 Corrected Mass/bag, g ( See Note 2) For both Type A & Type B 665 + 8.0 / -6.0 percent)	-
5-5.1-Table 1-Sr. No.v) (SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): a ) Warpway- 1570 (160) for both type A & Type B)	-
5-5.1-Table 1-Sr. No.v) (SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): b ) Weftway- 1420 (145) for both type A & Type B)	-
5-5.1-Table 1-Sr. No.vi) (SPECIFIC REQUIREMENTS-Cl. 8.7 of IS 9113 Average side seam strength (5 cm ×20 cm raveled strip), Min, N (kgf): 490 (50) for both type A & Type B)	-

Partial

-
-

131

IS 9471 : Part 7 (2000)

Modular lower limb orthotic components - Specification: Part 7 orthotic joint bars, ankle and knee (Upper And Lower)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (SHAPE AND DIMENSIONS)	-
4.2 (SHAPE AND DIMENSIONS)	-
6.1 (Workmanship and Finish)	-
6.2 (Workmanship and Finish)	-
7.0 (Bend Test)	-

Complete

-
-

132

IS 12594 (1988)

Hot - Dip zinc coating on structural steel bars for concrete reinforcement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 , Table 1 (Mass of Zinc coating , IS 6745)	-
5.2 (Freedom from defects , IS 2629)	-
5.3 (Adhesion of Galvanized coating)	-
Clause - 4, 4.1 (CARBON)	-
Clause - 4, 4.1 (SULPHUR)	-
Clause - 4, 4.1 (PHOSPHURS)	-
Clause - 4, 4.1 (MANGANESE)	-
Clause - 4, 4.1 (SILICON)	-
Clause - 4, 4.1 (ALUMINIUM)	-
Clause - 4, 4.1 (NITROGEN)	-

Partial

-
-

133

IS 8074 (1990)

Monocrotophossl - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Physical)	-
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point ( Abel ))	-
3.3 (Chemical)	-
3.3.1 (Monocrotophos Content)	-
3.3.1.1 (actual value of the monocrotophos content)	-
3.3.1.2 (average monocrotophos content)	-
3.3.2 (Free Aceto-Acetic Acid Monomethyl-amide ( MMA ) Content)	-
3.3.3 (Acidit)	-

Complete

-
-

134

IS 9585 (1980)

Specification for lactometers

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Size)	-
6.1, Table 1 (Length in mm of the bulb)	-

Partial

-
-

135

IS 2414 (2005)

Cycle and rickshaw pneumatic tyres - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Type)	-
4.2 (Designation)	-
5.1 & 5.2 (Dimensions)	-
6.1 (Construction)	-
6.2 (Tyre Cord)	-
6.3 (Tyre Casing Strength)	-
6.4 (Bead Wire Joint)	-
6.5 (Requirements of Ruber Compound)	-
6.6 (Adhesion test)	-

Partial

-
-

136

IS 12234 (1988)

plastic equilibrium float valve for cold water services

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6/6.1/6.4-Fig. 2A (CONSTRUCTION-Horizontal Inlet Shank type-Dimensions- 5 mm Max)	-
6/6.1/6.4-Fig. 2A (CONSTRUCTION-Horizontal Inlet Shank type-Dimensions- 6.5 to 8 mm)	-
6/6.1/6.4-Fig. 2A (CONSTRUCTION-Horizontal Inlet Shank type-Dimensions- 14.70 to 15.00 mm)	-
6/6.1/6.4-Fig. 2B (CONSTRUCTION-Vertical Inlet Shank type-Dimensions- minimum bore 9 mm )	-
6/6.1/6.4-Fig. 2B (CONSTRUCTION-Vertical Inlet Shank type-Dimensions- 35 mm minimum )	-
6/6.1/6.4-Fig. 2A (CONSTRUCTION-Horizontal Inlet Shank type -Dimensions- 48 mm)	-
6/6.1/6.4-Fig. 2A (CONSTRUCTION-Horizontal Inlet Shank type-Dimensions- 48 mm Min)	-
6/6.1/6.4-Fig. 2B (CONSTRUCTION-Vertical Inlet Shank type-Dimensions- 48 mm minimum )	-
2/2.1 (CLASSlFICATlON )	-
2/2.2-Fig. 1 (CLASSlFICATlON )	-
5/5.1 (MANUFACTURE AND WORKMANSHIP )	-
5/5.2 (MANUFACTURE AND WORKMANSHIP )	-
6/6.1/6.4-Fig. 2B (CONSTRUCTION-Vertical Inlet Shank type-Dimensions- L-As required by cistern manufacturer -mm )	-
6/6.2 (CONSTRUCTION)	-
6/6.2 (CONSTRUCTION)	-
6/6.3 (CONSTRUCTION)	-
6/6.5 (CONSTRUCTION-Screw threads)	-
6/6.5 (CONSTRUCTION-Screw threads)	-
6/6.6 (CONSTRUCTION)	-
6/6.6 (CONSTRUCTION)	-
6/6.7 (CONSTRUCTION)	-
6/6.7 (CONSTRUCTION)	-
6/6.7 (CONSTRUCTION)	-
6/6.8 (CONSTRUCTION)	-
6/6.8.1 (CONSTRUCTION)	-
6/6.8.2 (CONSTRUCTION)	-
6/6.9 (CONSTRUCTION-Floats)	-
6/6.9 (CONSTRUCTION-lack Nut)	-
7-7.1-7.1.1 (PERFORMANCE TESTS -Hydraulic and Shut-Off Test )	-
7-7.1-7.1.2 (PERFORMANCE TESTS -Hydraulic and Shut-Off Test )	-
7-7.2-7.2.1 (PERFORMANCE TESTS -Antisiphonage test-Appendix A)	-
7-7.3-7.3.1 (PERFORMANCE TESTS -Flow Test -Appendix B)	-

Complete

-
-

137

IS 3903 (1984)

Specification for dimethoate emulsifiable concentrates

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.3.2 (Acidity)	-
2.3.1 (Dimethoate Content, NV upto 9)	-
2.3.1 (Dimethoate Content, NV above 50)	-
2.2.3 (Flash Point)	-
2.1 (Constituents)	-
2.2.1 (Description)	-
2.2.2 (Cold Test)	-
2.2.4 (emulsion Stability)	-
2.2.5 (Heat Stability)	-
2.2.4 (emulsion Stability)	-
2.2.5 (Heat Stability)	-
2.3.1 (Dimethoate Content, NV above 9 and below 50)	-

Partial

-
-

138

IS 6956 (2001)

Cover paper - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3 (Grarnmage-As per 6 of IS 1060 (Part 1)-Further a mean of 10 test results shall not vary from nominal grarnmage by more than ±4 percent.)	-
4.3 (Grarnmage-As per 6 of IS 1060 (Part 1)- no single test result shall vary by more than *6 percent from nominal)	-
4.2,Table1 (One minute Cobb test (Test method Column 4 and 5 of table1))	-
4.3 (Grarnmage-As per 6 of IS 1060 (Part 1)-Further a mean of 10 test results shall not vary from nominal grarnmage by more than ±4 percent.)	-
4.3 (Grarnmage-As per 6 of IS 1060 (Part 1)- no single test result shall vary by more than *6 percent from nominal)	-
4.2,Table1 (One minute Cobb test (Test method Column 4 and 5 of table1))	-

Partial

-
-

139

IS 2566 (1993)

Textiles – B-twill jute bags for packing foodgrains – Specification (third revision)

- View breakup
Rs 4800/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5.2 & Table 2. IS 2969 ( The bales containing the bags shall conform to the requirements as laid down in Table 2. vi) Oil content on dry deoiled material basis, percent, Max)	-

Partial

-
-

140

IS 5604 (1984)

Specification for hand - Operated universal gearless pulling and lifting machines (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Capacity)	-
5.3 (Construction and Workmanship Casing)	-
5.4 (Construction and Workmanship Bearings)	-
5.4.1 (Ball and Roller Bearings)	-
5.4.2 (Plain Bearings)	-
5.5 (Wire Ropes)	-
5.6 (Heat Treatment)	-
5.7 (Construction and Workmanship Bearings)	-
5.8 (Weight)	-
7.1 (Operation)	-
7.2 (Operation)	-
7.3 (Operation)	-
7.4 (Operation Back Slippage)	-
8 (Effort)	-
9.1 (Proof Loading)	-
9.2 (Operational Test)	-
9.3 (Break Load Testing )	-
9.4 (Examination)	-
11.1 (Marking)	-
Clause -3, 3.1 (Steel bars, Plates and sections)	-
Clause -3, 3.1 (Steel Forgings)	-
Clause -3, 3.1 (Aluminium Alloy)	-
Clause -3, 3.1 (Coil Springs)	-
Clause -3, 3.1 (Hooks)	-
Clause -3, 3.1 (Wire Ropes)	-

Partial

-
-

141

IS 5531 (2014)

Cast iron specials for asbestos cement pressure pipes for water and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

142

IS 1943 (1995)

Textiles – A-twill jute bags (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1,5.1,Table 1 (Moisture Regain, Percent-IS 9113)	-
4.1,5.1,Table 1 (Oil content, Percent-IS 2969)	-

Partial

-
-

143

IS 3992 (1982)

Specification for trays, kidney (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1&3.2 (C - IS 228)	-
3.1&3.2 (S - IS 228)	-
3.1&3.2 (P - IS 228)	-
3.1&3.2 (Mn - IS 228)	-
3.1&3.2 (Si - IS 228)	-
3.1&3.2 (Cr - IS 228)	-
3.1&3.2 (Ni - IS 228)	-
4.1 (Shape)	-
4.2, Table-1,1 (Length -A - IS 3992)	-
4.2, Table-1,2 (Width -B - IS 3992)	-
4.2, Table-1,3 (Height -C - IS 3992)	-
4.2, Table-1,7 (Minimum Thickness of material)	-
5.0 &5.1 (Workmanship and finish of stainless steel Trays)	-
5.0 & 5.2 (Workmanship and finish of Enamelled Iron Trays)	-

Partial

-
-

144

IS 3993 (1993)

Trays, instruments - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 & 4.2 (C - IS 228)	-
4.1 & 4.2 (S - IS 228)	-
4.1 & 4.2 (P - IS 228)	-
4.1 & 4.2 (Mn - IS 228)	-
4.1 & 4.2 (Si - IS 228)	-
4.1 & 4.2 (Cr - IS 228)	-
4.1 & 4.2 (Ni - IS 228)	-
5 (Shape)	-
5.2 -Table-1 (Length -A - IS 3993)	-
5.2 -Table-1 (Width -B - IS 3993)	-
5.2 -Table-1 (Height -C - IS 3993)	-
5.2 -Table-1 (Minimum no of Ribs - IS 3993)	-
5.2 -Table-1 (Minimum Finished Thickness - IS 3993)	-
6.1 & 6.2 (Manufacture, workmanship and finish of Stainless Steel Tray)	-
6.1 & 6.3 (Manufacture, workmanship and finish of Enamelled Iron Trays - IS 3993)	-
6.1 & 6.4 (Manufacture, workmanship and finish of Glass Trays - IS 3993)	-

Partial

-
-

145

IS 2692 (1989)

Ferrules for water services ? specification

- View breakup
Rs 3450/- + Materials as per respective ISS

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

146

IS 2932 (2013)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.3 (Freedom from Coarse Particles)	-
6.4 (Skin Formation)	-
6.5 (Thinning Properties)	-
6.6 (Application Properties)	-
6.8 (Lead Restriction)	-
6.9 Table 2 (1) a. Consistency ( Undercoating and Finishing ) )	-
6.9 Table 2 (1) b. Viscosity by ford 80-120 s )	-
6.9 Table 2 ( 2) Mass, ( Under coating ) )	-
6.9 Table 2 ( 2) Mass, (Finishing ) )	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Under coating ) )	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Finishing ) )	-
6.9 Table 2 (b) Hard dry ( Under coating ) )	-
6.9 Table 2 (b) Hard dry, (Finishing ) )	-
6.9 Table 2 (c) Tack free ( Under coating (Finishing ) )	-
6.9 Table 2 (4) a) Finish (Under coating ) )	-
6.9 Table 2 (4) a) Finish (Finishing) )	-
6.9 Table 2 (b) ) Gloss 60º (Under coating ) )	-
6.9 Table 2 (b) ) Gloss 60º (Finishing) )	-
6.9 Table 2 (5) Fineness of grind,(Under coating ))	-
6.9 Table 2 (4) a) Finish (Finishing) )	-
6.9 Table 2 (6) Colour , (Finishing))	-
6.9 Table 2 (7) Flexibility and adhesion: a) Scratch hardness No such scratch as to show the bare metal after Clause 3 of — (Load 1 000 g) ( Under coating & Finishing ) )	-
6.9 Table 2 (b) Bend test (with 6.25 mm 48 h of air in type 1 apparatus) ( Under coating & Finishing ) )	-
6.9 Table 2 (8) Flash point ( Under coating & Finishing ) )	-
6.9 Table 2 (9) Composition:b) Phthalic anhydride content of non-volatile vehicle ( Under coating & Finishing ))	-
6.9 Table 2 (11) Resistance to alkali ( Under coating & Finishing ))	-
6.9 Table 2 (12) Accelerated storage stability test ( Under coating & Finishing ))	-
6.9 Table 2 (13) Keeping properties ( Under coating & Finishing ))	-
6.9 Table 2 (14) Wet opacity ( Under coating & Finishing ))	-

Partial

-
-

147

IS 10350 (2020)

Powder Hair Dyes — Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 1 (Arsenic (as As2 O3 ), for all types)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 2 (pH, Type 3)	-
4.5 Table 1 (pH, type 1 and 2)	-
4.5 Table 1 (Active matter as PPD content, Type 1)	-
4.1 (description)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 1 (Arsenic (as As2 O3 ), for all types)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 1 (pH, type 1 and 2)	-
4.5 Table 1 (Heavy metals (as Pb), for all types)	-
4.5 Table 1 (Active matter as PPD content, Type 1)	-
4.1 (description)	-
4.5 Table 1 (Dye ingredients, type 3 only)	-

Complete

-
-

148

IS 191 (2007)

Copper - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

149

IS 4003 : Part 2 (1986)

Specification for pipe wrenches: Part 2 heavy duty (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 AND AS PER IS 1570 PART 2 (CARBON)	-
4 AND AS PER IS 1570 PART 2 (SULPHUR)	-
4 AND AS PER IS 1570 PART 2 (PHOSPHORUS)	-
4 AND AS PER IS 1570 PART 2 (MANGANESE)	-
4 AND AS PER IS 4454 PART 1 (CARBON)	-
4 AND AS PER IS 4454 PART 1 (SULPHUR)	-
4 AND AS PER IS 4454 PART 1 (PHOSPHORUS)	-
4 AND AS PER IS 4454 PART 1 (MANGANESE)	-
4 AND AS PER IS 4454 PART 1 (SILICON)	-
4 AND AS PER IS 4454 PART 1 (COPPER)	-
4 AND AS PER IS 4454 PART 1 (NITROGEN)	-
4 AND AS PER IS 4454 PART 1 (cu + cr + ni)	-
4 AND AS PER IS 4454 PART 1 (SULPHUR+ PHOSPHORUS)	-
4 AND AS PER IS 4454 PART 1 (MICRO ALLOY)	-
4 AND AS PER IS 2707 (CARBON)	-
4 AND AS PER IS 2707 (SULPHUR)	-
4 AND AS PER IS 2707 (PHOSPHORUS)	-
4 AND AS PER IS 2707 (MANGANESE)	-
4 AND AS PER IS 2707 (SILICON)	-
4 AND AS PER IS 2707 (MICRO ALLOY)	-
3 (Dimensions- Nominal Size)	-
3 (Dimensions-Capacity D min)	-
3 (Dimensions- Capacity D max)	-
3 (Dimensions- Jaw Thickness,T min)	-
3 (Dimensions- Length of movablejae, l1)	-
3 (Dimensions- Length of Handle, l2)	-
3 (Dimensions- Width of Nut, N)	-
5 (Hardness- Movable and heel Jaws)	-
5 (Hardness- Shank of movable Jaw)	-
5 (Hardness- Adjustable nut)	-
6.1 (Manufacture- Handel)	-
6.1 (Manufacture- Handel)	-
6.2 (Movable Jaw)	-
6.2 (Movable Jaw)	-
6.3 (Heel jaw)	-
6.3 (Heel jaw)	-
6.4 (Adjusting Nut)	-
6.4 (Adjusting Nut)	-
6.4 (Adjusting Nut)	-
6.5 (Springs)	-
6.5 (Springs)	-
7 (Workmanship & Finish)	-
7 (Workmanship & Finish)	-
8 (Operation)	-
11.1 (Static Load Test)	-
11.1 (Static Load Test)	-

Complete

-
-

150

IS 4766 (1982)

Specification for thiram water dispersible powders (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.3 Table 1 (Wettability)	-
2.1 (Description)	-
2.3 Table 1 (Suspensbility after accelarated storage)	-
2.3 Table 1 (Wettability)	-
2.1 (Description)	-
2.3 Table 1 (Suspensbility after accelarated storage)	-

Partial

-
-

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- [email protected]

Scope List

No Record Found

No Record Found

No Record Found

No Record Found