BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- [email protected]

Scope List

Reset

773 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 5672 (1992)

Mineral mtxtures for supplementing poultry feeds - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.4 Table 1 (Moisture, percent by mass,)	-
3.4 Table 1 (Acid insoluble ash)	-
3.4 Table 1 (Iodine ( as KI ))	-
3.4 Table 1 (Manganese)	-
3.4 Table 1 (Zinc)	-
3.4 Table 1 (Phosphorus,)	-
3.4 Table 1 (Calcium,)	-
3.4 Table 1 (Copper,)	-
3.4 Table 1 (Iron)	-
3.2 (Descrption)	-

Partial

-
-

IS 3309 (1992)

Soluble Coffee - Chicory powder - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.4 Table 1 (Moisture content)	-
3.4 Table 1 (Total ash)	-
3.7 (Copper content)	-
3.1 (Description)	-
3.4 Table 1 (Solubility in boiling)	-
3.4 Table 1 (Solubility in cold water)	-

Partial

-
-

IS 6014 (1978)

Specification for emulsifiable larvicidal oil, pyrethrum based (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.2 (Flash Point (Abel))	-
2.2.3 (Emulsion Stability)	-
2.2.4 (Relative Density)	-

Partial

-
-

IS 2791 (1992)

Soluble coffee powder - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.4 Table 1 (Moisture content)	-
3.4 Table 1 (Total ash)	-
3.4 Table 1 (Solubility in boiling)	-
3.1 (Description )	-
Clause no 3.52.3 (freedom from adulterants)	-
Clause no 3.5.2.2 (freedom from extraneous matter)	-

Complete

-
-

IS 2785 (1979)

Specification for natural cheese (Hard Variety), processed cheese, processed cheese spread and soft cheese (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3.1 (Appearance)	-
3.3.2 (Odour and Flavour)	-
3.3.3 (Texture and Consistency)	-
3.3.4- Table 1-i (Moisture- Annex A)	-
3.3.4- Table 1-ii (Milk fat ( on dry basis)- Annex B)	-
3.3.4- Table 1-iii (Salt ( added sodium chloride)- Annex C)	-

Complete

-
-

IS 1697 (1994)

Erythrosine, food grade - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Contaminants)	-

Partial

-
-

IS 5719 (2017)

Gelatin, food grade - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description)	-
4.2.1 (Solubility)	-
4.2.2 (Precipitate formation)	-
4.2.3 (Development of turbidity)	-
Cl. 4.3 (Table 1, S. no i) (Loss on drying)	-
Cl. 4.3 (Table 1, S. no ii) (Gel strengt)	-
Cl. 4.3 (Table 1, S. no iii) (Total Ash)	-
Cl. 4.3 (Table 1, S. no iv) (Sulphur dioxide)	-
Cl. 4.3 (Table 1, S. no v) (Nitrogen)	-
Cl. 4.3 (Table 1, S. no vi) (Lead)	-
Cl. 5.7(Table 1, S. no vii) (Arsenic)	-
Cl. 5.7 (Table 1, S. no viii) (Mercury)	-
Cl. 5.7 (Table 1, S. no ix) (Cadmium)	-
Cl. 5.7 (Table 1, S. no x) (Chromium)	-
Cl. 5.7 (Table 1, S. no xi) (Heavy Metals)	-
Cl. 4.5 (Microbiological Requirements)	-

Complete

-
-

IS 1838 : Part 1 (1983)

preformed fillers for expansion joint in concrete pavement and structures (non extruding and resilient type): Part 1 Bitumen impregnated fibre - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Dimensions and tolerances)	-
5 Table-1 vi (Test for Density in accordance with IS 10566:1983 )	-
5 Table-1 viii (Weathering test in accordance with IS 10566:1983)	-

Partial

-
-

IS 9537 : Part 4 (1983)

Specification for conduits for electrical installations: Part 4 pliable self - Recovering conduits of insulating materials

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Marking, IS 9537-4)	-
6.1 (Marking, IS 9537-4)	-
6.1 (Marking, IS 9537-4)	-
6.1 (Marking, IS 9537-4)	-
6.2 (Marking, IS 9537-4)	-
6.2.1 (Marking, IS 9537-4)	-
6.3 (Marking, Cl. 6.4 of IS 9537-1)	-
6.4 (Marking, IS 9537-4)	-
7.1 (Dimensions (Maximum outside Diameter), IS 9537-4)	-
7.3.3 (Uniformity of wall thickness, IS 9537-4)	-
8.1 (Construction, Cl. 8 of IS 9537-1)	-
9.3 (Mechanical Properties (Compression Test), IS 9537-4)	-
9.4 (Mechanical Properties (Impact Test), Cl. 9.4 of IS 9537-1)	-
11 (Resistance to burning, Cl. 11 of IS 9537-1)	-
12 (Electrical Strength, Cl. 12.1.1 of IS 9537-1)	-
12 (Insulation Resistance, Cl. 12.1.2 of IS 9537-1)	-

Complete

-
-

IS 15559 (2004)

Polyester strapping - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Manufacture)	-
4.1 (Manufacture)	-
4.2 (Surface finish)	-
4.3 (Colour)	-
4.5 (Freedom from Defects)	-
4.6, Table-1 (Dimensions and Physical Properties)	-
5.2 (Split Resistance)	-
5.3, Table-3 (Camber)	-
Table-1 (4) (Type)	-
Table-2 (4) (Type)	-

Partial

-
-

IS 14928 (2001)

Textiles - Composite synthetic fibre ropes - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.1 (Construction)	-
5.2.2 (Construction)	-
5.2.3 (Construction)	-
5.3 (Structure)	-
5.4 (Treatment)	-
5.5 ( Rope)	-
6.1, Table 1 /Table 2. ( Breaking Strength, Min)	-
6.2, Table 1 and Table 2 ( Mass of the Coil)	-
6.3 ( Length of Coil)	-
8.1 (a) (MARKING)	-
8.1 (b) (MARKING)	-
8.1 (c) (MARKING)	-
8.1 (d) (MARKING)	-
8.1 (e) (MARKING)	-

Partial

-
-

IS 5135 : Part 1 (1994)

Specification for hand - Rotary duster: Part 1 belly - Mounted type (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Capacity)	-
7.4 (Leakage)	-
8.0 (WORKMANSHIP AND FINISH)	-

Partial

-
-

IS 1422 (1983)

Specification for cotton duck (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.2, Table 2, Sr. No. 1 (Scouring loss, Scoured or Dyed)	-
Cl 4.2, Table 2, Sr. No. 1 (Scouring loss, Grey)	-
Cl 4.2, Table 2, Sr. No. 2 (pH value )	-

Partial

-
-

IS 2923 (1995)

Carmoisine, food grade - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 Table 1 (Water-insoluble matter)	-
3.1 Table 1 (Combined ether extracts)	-
3.1 Table 1 (Arsenic)	-
3.1 Table 1 (Lead)	-
3.1 Table 1 (Loss on drying at 135 C)	-
3.1 Table 1 (Heavy metals)	-
3.1 Table 1 (Total dye content,)	-

Partial

-
-

IS 2415 (2015)

Cycle - Rubber tubes (Moulded/ Jointed) - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1, Table 1 (Classification and Designation)	-
5.1,3.4, Annex A & Table 2. ( Flat Length )	-
5.1,3.5, Annex A & Table 2. (Flat Width)	-
5.2, Annex A (Thickness)	-
5.2.1 (Uniformity of Thickness)	-
6.1,Table 3 (i)Tensile strength:)	-
6.1,Table 3 (ii)Elongation at break )	-
6.2 (iii)Tension set: )	-
6.3 (a) ( Ageing Test:- Tensile strength :)	-
6.3(b) ( Ageing Test :- Elongation at break)	-
6.4.1 (Joint Adhesion Strength)	-
6.4.3 ( Strength of splice on moulded tube)	-
6.5 (Leak Test)	-
6.6 (Valve Test)	-
6.7.1 (Manufacture and Workmanship)	-
6.7.2 (Manufacture and Workmanship)	-
6.7.3 (Manufacture and Workmanship)	-
6.7.4 (Manufacture and Workmanship)	-
7.1 (MARKING)	-

Partial

-
-

IS 12866 (1989)

Plastic translucent sheets made from thermo - Setting polyester resin (Glassfibre Reinforced) - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.3 (Water Absorption)	-
4-4.1-Table 1 ( PROFILES, DIMENSIONS AND TOLERANCES-Profiles)	-
4-4.2-Table 1 ( PROFILES, DIMENSIONS AND TOLERANCES-Profiles - Depth of Corrugation, D )	-
4-4.2-Table 1 ( PROFILES, DIMENSIONS AND TOLERANCES-Profiles - Pitch of Corrugation, P )	-
4-4.2-Table 1 ( PROFILES, DIMENSIONS AND TOLERANCES-Profiles - Overall Width, B)	-
4-4.2-Table 1 ( PROFILES, DIMENSIONS AND TOLERANCES-Profiles - Effective Width)	-
4-4.2-Table 1 ( PROFILES, DIMENSIONS AND TOLERANCES-Profiles - Minimum Thickness, T)	-
4-4.2-Table 1 ( PROFILES, DIMENSIONS AND TOLERANCES-Profiles - Length of Sheet, A)	-
5-5.1 (WOIRKMANSHlP AND FlNISH)	-
5-5.2 (WOIRKMANSHlP AND FlNISH)	-
6-6.1 (PERFORMANCE REQUIREMENTS-Density- The nominal weight of 1.10 + 0·15 mm Thick plain sheet shall be 1.85 kg/sq. m)	-
6-6.5-Annex D (PERFORMANCE REQUIREMENTS-Bolt Shear Test -When tested in accordance with Annex D, the arithmetic mean of the loads at which the first tear appears, shall be not less than 375 N. The load at which the first tear appears while testing any one of the specimens, shall be not less than 250 N. )	-
6-6.6- Table 2-Annex E (PERFORMANCE REQUIREMENTS-Load Deflection Test-Applicable only to corrugated sheets and flats of curved sheets. Toal Load N )	-

Partial

-
-

IS 5382 (2018)

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1 (Dimensional tolerances)	-
4.2.2 (Imperfections and defects)	-
4.2.2 (Surface imperfections)	-
4.2.2 (i)In zones involved in sealing function)	-
4.2.2 (ii) In zones not involved in sealing function)	-
4.2.2 (Internal Imperfections)	-
4.2.3 (Hardness, IRHD from buttons )	-
4.2.4 (Tensile strength, MPa)	-
4.2.5 (Compression set in air)	-
4.2.5.2 (Compression set at 23 ºC for 72 h)	-
4.2.5.2 (Compression set at 70 ºC for 24 h)	-
4.2.5.3 (Low temp compression set at -10 ºC for 72 h)	-
4.2.6 (Ageing 7 days at 70 ºC)	-
4.2.6 (Hardness, IRHD from buttons Tensile strength, % Elongation at break , % )	-
4.2.8 (Volume change in water , max/min 7 days at 70 ºC )	-
4.2.10 (Spliced joint)	-

Partial

-
-

IS 3623 (1978)

Specification for guide and rubbing ropes (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Size - IS 3623)	-
3.2 (Length - IS 3623)	-
4.3 (Galvanized Test - IS 3623)	-
5, Table 1, Table 2 (Mass)	-
5, Table 1, Table 2 Annex B (Minimum Breaking Force - IS 16594 )	-
6.1-fig-1 (Construction)	-
6.2.1 (Construction)	-
7.1 (Workmanship)	-
7.2 (Joints)	-
3.1 (Size - IS 3623)	-
3.2 (Length - IS 3623)	-

Complete

-
-

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-
Cl.7.1 Dimensions (Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-
Cl.7.2 Radius at base (Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-
Cl.7.2 Radius at base (Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-
Cl.7.3 Wall thickness (Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-
Cl.8.1 Base (The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-
8.2 Upper edge (The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-
Cl. 8.3 Spout (The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-
Cl.8.5 Thermal shock resistance (Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-

Partial

-
-

IS 5487 (1992)

Metal polish, liquid - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.8, Table-1 (vi) (Oleic acid content, IS 5487 )	-
4.8, Table-1 (v) (Flash point (Abel), IS 1448 Part-20)	-
4.8, Table-1 (iv) (Cyanides, IS 5487)	-
4.8, Table-1 (iii) (Residue on 75miron IS Sieve, IS 5487)	-
4.8, Table-1 (ii) (Total ammonia (as NH3), IS 5487)	-
4.8, Table-1 (i) (Total solids (excluding oils and fatty matter), IS 5487)	-
4.7 (Keeping Quality, IS 5487)	-
4.6 (Acidity of the Aqueous Extract, IS 5487)	-
4.5 (Polishing Property, IS 5487)	-
4.4 (Stability, IS 5487)	-
4.3 (Consistency, IS 5487 )	-
4.8, Table-1 (v) (Flash point (Abel), IS 1448 Part-20)	-

Complete

-
-

IS 6406 (1994)

Brilliant blue FCF, food grade - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 Table 1 (Total dye content)	-
3.1 Table 1 (Combined ether extracts)	-
3.1 Table 1 (Heavy metals - Lead, )	-
3.1 Table 1 (Water-insoluble matter)	-
3.1 Table 1 (Total dye content)	-
3.1 Table 1 (Combined ether extracts)	-
3.1 Table 1 (Heavy metals - Lead, )	-
3.1 Table 1 (Water-insoluble matter)	-

Partial

-
-

IS 878 (2008)

Laboratory glassware - Graduated measuring cylinders (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1 (Nominal capacity)	-
Table-1 (Overall height)	-
Table-1 (Distance from top of scale to top of cylinder)	-
Table-1 (Internal height to highest graduation line)	-
Table-1 (Sub-divisions)	-
Table-1 (capacity at lowest graduation line)	-

Partial

-
-

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7.1 (Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-
Cl 12.2 (Concavity & Convexity )	-
Cl 12.3 (The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-
Cl 12.4 (Shall not exceed 1 percent of the length of the edge.)	-
Cl 12.5 (Water absorption)	-
Cl 11 (Suface Finish)	-

Partial

-
-

IS 8471 (2003)

Acetylene generators - Requirements (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (MATERIAL AND PROTECTIVE COATING)	-
7.2 (MATERIAL AND PROTECTIVE COATING)	-

Partial

-
-

IS 4964 (2013)

Textiles – Vests, cotton, plain (Single jersey) knitted – Specification (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4/4.1 (MANUFACTURE AND FINISH- Fabric-see IS 9469)	-
4/4.1/4.1.1 (MANUFACTURE AND FINISH- Fabric-The mass of the vest-method given in B-5.)	-
4/4.1/4.1.2 (MANUFACTURE AND FINISH- Fabric-)	-
4/4.1/4.1.3 (MANUFACTURE AND FINISH- Fabric-)	-
4/4.2-Fig. 1A, Fig. 1B, Fig. 2A, Fig. 2B, Fig. 3. (MANUFACTURE AND FINISH)	-
4/4.2/4.2.1 (MANUFACTURE AND FINISH)	-
4/4.3/4.3.2-according to B-4 (MANUFACTURE AND FINISH-Seams and Stitches-Dimension)	-
4/4.3/4.3.3 (MANUFACTURE AND FINISH-Seams and Stitches)	-
4/4.4 (MANUFACTURE AND FINISH)	-
4/4.6 (MANUFACTURE AND FINISH-Freedom from Defects)	-
5/5.1-Tables 2 and 3 (REQUIREMENTS-Dimensions-method prescribed in Annex B.)	-

Partial

-
-

IS 2888 (2004)

Toilet soap - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.5, Table-1 (vii), Grade-3 (Lather)	-
5.5, Table-1 (vii), Grade-2 (Lather)	-
5.5, Table-1 (vii), Grade-1 (Lather)	-
5.5, Table-1 (vi), Grade-1, Grade-2 & Grade-3 (Free carbonated alkali)	-
5.5, Table-1 (v), Grade-1, Grade-2 & Grade-3 (Chloride (as sodium chloride), IS 286)	-
5.5, Table-1 (iv), Grade-2 & Grade-3 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iv), Grade-1 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iii), Grade-1, Gr-2 & Gr-3 (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.5, Table-1 (ii), Grade-1, Gr-2 & Gr-3 (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.5, Table-1 (i), Grade-3 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-2 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-1 (Total fatty matter, IS 286)	-
5.5, Table-1 (vii), Grade-3 (Lather)	-
5.5, Table-1 (vii), Grade-2 (Lather)	-
5.5, Table-1 (vii), Grade-1 (Lather)	-
5.5, Table-1 (vi), Grade-1, Grade-2 & Grade-3 (Free carbonated alkali)	-
5.5, Table-1 (v), Grade-1, Grade-2 & Grade-3 (Chloride (as sodium chloride), IS 286)	-
5.5, Table-1 (iv), Grade-2 & Grade-3 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iv), Grade-1 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iii), Grade-1, Gr-2 & Gr-3 (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.5, Table-1 (ii), Grade-1, Gr-2 & Gr-3 (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.5, Table-1 (i), Grade-3 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-2 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-1 (Total fatty matter, IS 286)	-

Complete

-
-

IS 7098 : Part 3 (1993)

Cross - Linked polyethylene insulated thermoplastic sheathed cables - Specification: Part 3 for working voltages from 66 kV up to and including 220 kV

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (CONDUCTOR)	-
6 (SCREENING)	-
8.1 (INNER SHEATH)	-
8.2 (INNER SHEATH)	-
8.3 (INNER SHEATH)	-
9.1 (ARMOUR)	-
10.1 (OUTER SHEATH)	-
10.2 (OUTER SHEATH)	-
11.1 (CONDUCTOR)	-
11.2 (CONDUCTOR)	-
12.1 (CONDUCTOR SCREENING )	-
12.2 (CONDUCTOR SCREENING )	-
13.1 (INSULATION)	-
13.2 (INSULATION)	-
14.1 (INSULATION SCREENING)	-
14.2.1 (INSULATION SCREENING : Non-metallic Part)	-
14.2.2 (INSULATION SCREENING : Non-metallic Part)	-
14.2.3 (INSULATION SCREENING : Non-metallic Part)	-
14.3.1 (INSULATION SCREENING : Metallic Part)	-
14.3.2 (INSULATION SCREENING : Metallic Part)	-
14.3.3 (INSULATION SCREENING : Metallic Part)	-
15.1 (MOISTURE BARRIER)	-
15.2.1 (Metallic Sheath)	-
15.2.2 (Metallic Sheath)	-
16.1 (INNER SHEATH)	-
16.2 (INNER SHEATH)	-
17.1 (ARMOUR)	-
17.2 (ARMOUR)	-
17.3 (ARMOUR)	-
17.4 (ARMOUR)	-
17.5 (ARMOUR)	-
18.1 (OUTER SHEATH)	-
18.2 (outer sheath colour)	-
18.3.1 (Thickness of Outer Sheath : Unarmoured Cables)	-
18.3.1 (Thickness of Outer Sheath : armoured Cables)	-
19.1 A) I) (Tests on conductor : Annealing test ( for copper ))	-
19.1 A) II) (Tests on conductor : Resistance test)	-
19.1 g)2) i) (PVC sheath : Tensile strength and elongation at break)	-
19.1 g)2) iii) (PVC sheath : Loss of mass)	-
19.1 g)2) v) (PVC sheath : Hot deformation test)	-
19.1 g)2) vi) (PVC sheath : Shrinkage test)	-
19.1 g)2) vii) (PVC sheath : Thermal stability)	-
20.7 (Flammabihty test ( for PVC outer sheathed cables only ))	-
20.16.2 (Test for Dimensions of Insulation : Test for Eccentricity)	-
20.16.3 (Test for Dimensions of Insulation : Test for Ovality)	-

Partial

-
-

IS 4355 (1977)

Specification for fire-resistant brattice cloth (first revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3.2 Length and width (The length and width of finshed fabric shall be as agreed between the purchase and the supplier .A Tolerance of - 5% shall be alowed on width)	-
Cl.3.3.1 (The treatment of the base fabric to make it fabric uniformly and adhere firmly to the fabric)	-
Cl.3.3.2 (The treatment material shall penetrate the fabric uniformly and adhere firmly to the fabric.)	-
Cl.3.3.3 (The treated fabric shall have a reasonable durability under all condition of usage )	-
Cl.3.3.4 (The treated fabric shall have any undesirable odour and shall be non irritant to skin)	-
Cl.3.4.2 (The breaking load of the brattice cloth for wrapway and weftway shall not be leass than 40 Kgf and 20 Kgf respectiveely when tested in accordance with IS 1969-1068 on a specimen of 5 cm width)	-

Partial

-
-

IS 6444 (1979)

Specification for sulphur dusting powders (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-

Complete

-
-

IS 651 (2007)

Glazed stoneware pipes and fittings - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (GENERAL QUALITY)	-
5.2(a) (GENERAL QUALITY)	-
5.2(b) (GENERAL QUALITY)	-
5.2(c) (GENERAL QUALITY)	-
6 ( GLAZING)	-
7.2 (Hydraulic Test)	-
7.3 (Absorption Test)	-
10.1-Table 1 (INTERNAL DIAMETER)	-
10.1-Table 1 (Class)	-
11.1-Table 1 ( Mean Thickness of Barrel and of Socket)	-
14-Table 1 (Internal Depth of Socket)	-
14-Table 2 (Excess Shoulder Measurment)	-
14-Table 3 (Length of Grooving of Spigot)	-
12.4 (Permissible Deviation from Straightness)	-
12.2 (STRAIGHTNESS OF BARRELS OR STRAIGHT AND TAPER PIPES-Length of Junction)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-Internal Diameter)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-r)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-angle)	-
13.1-Table 3 (Dimensions of One-Eighth Bends--Internal Diameter)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-r)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-angle)	-
13.1-Table 4 (Dimension of One-Sixteenth Bends-Internal Diameter)	-
13.1-Table 4 (Dimension of One-Sixteenth Bends-r)	-
13.1-Table 4 (Dimension of One-Sixteenth Bends-angle)	-

Complete

-
-

First
Prev
2
3
4
5
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- [email protected]

Scope List