BIS - LIMS (Laboratory Information Management System)

CIPET, Bhubaneswar

B/25, C.N.I complex, Patia, Bhubaneswar, BHUBANESWAR, Khordha, Odisha, 751024

7566177001 [email protected]

Scope List

Reset

72 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	500.00	nil
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	500.00	nil
3.2.3(Socket, measurements)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 7328 (2020)

Specification for Polyethylene Material for Moulding and Extrusion ( Third Revision )

NIL

24650.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1.1(Density)	-	500.00	nil
5.2.1.2(MFI)	-	1100.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at yield)	-	1350.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at yield)	-	0	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at break)	-	0	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at break)	-	0	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec7)(Flexural modulas)	-	1350.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec6)(Dart Impact strength)	-	1000.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec4)(Izod/Charpy impact strength)	-	1350.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec11)(Shore Aor D hardness)	-	375.00	nil
5.3.2 Table 6 IS 13360 (Part 11/Sec1)(Coeffiicient of friction)	-	850.00	nil
5.3.2 Table 6 IS 13360 (Part 6/Sec3)(Heat deflection temperature)	-	1100.00	nil
5.3.2 Table 6 IS 13360 (Part 6/Sec1)(Vicat softening temperature)	-	1100.00	nil
Annex B of IS 4984 5.3.2 Table6(Oxidation induction time)	-	2200.00	nil
5.5.6 IS 2530(Carbon black dispersion)	-	700.00	nil
5.4.3 10 ofIS 2530(Carbon black content)	-	925.00	nil
IS 13360(part8/Sec1)(Water absorption)	-	600.00	nil
5.4.35 15 ofIS 2530(Colour fastness to daylight)	-	850.00	nil
5.4.2 13 ofIS 2530(Colour fastness to water)	-	1750.00	nil
5.4.1 12 of IS 2530(Colour bleeding)	-	2000.00	nil
IS 13360(part 8/Sec9)(ESCR)	-	1200.00	nil
Annex C of IS4984(Volatile content)	-	700.00	nil
4 of IS 7016 (part 8)(Oven ageing)	-	700.00	nil
IS 13360(part 9/Sec8)(Transparency)	-	700.00	nil
IS15827(Natural/artificial weathering)	-	850.00	nil
IS 13360(part 9/Sec7)(Specular gloss)	-	700.00	nil
IS 13360(part 9/Sec5)(Haze or luminious transmittance)	-	700.00	nil

Complete

31 Dec, 2023

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

Type- A & Type-B

20244.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300.00	nil
10.1(Surface Finish)	-	0.00	nil
7.2.1.1 Table3(Angle of taper (Note-1))	-	0.00	nil
10.7(Sulphated Ash Content)	-	950.00	nil
5(CLASSIFICATION OF PIPES)	-	0.00	nil
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0.00	nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0.00	nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0.00	nil
7.2.1(DIMENSIONS-Socket)	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0.00	nil
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0.00	nil
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0.00	nil
8(SEALING RINGS)	-	0.00	nil
9.1(PIPE ENDS)	-	0.00	nil
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300.00	nil
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0.00	nil
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575.00	nil
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900.00	nil
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100.00	nil
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500.00	nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000.00	nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850.00	nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000.00	nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850.00	nil
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850.00	nil
11.2(Resistance to External Blows at 0°C)	-	1400.00	nil
10.3(Effect on Water Test)	-	3000.00	nil
6.1.2(PVC Resin)	-	4100.00	nil
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500.00	nil
7.1.4(Length)	-	0.00	nil

Complete

31 Dec, 2023

-
-

IS 8391 : Part 1 (2019)

Rubberized coir sheets for cushioning “ Specification Part 1 Curled (third revision)

Rubberized coir sheet for cushioning

14700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.7.1 (Density, Annex C)	-	500.00	nil
7.7.2(Indentation Hardness, Annex D)	-	1100.00	nil
7.7.3(Resistance to Ageing, Annex E)	-	2300.00	nil
7.7.4(Resistance to Flexing, Annex F)	-	3500.00	nil
7.7.5(Compression Set (Aged), Annex G)	-	1200.00	nil
7.7.6(Compression Set (Un-aged), Annex G)	-	900.00	nil
7.7.7(pH Value, Annex H)	-	350.00	nil
7.7.8(Chloride Content, Annex J)	-	1000.00	nil
7.7.9(Sulphate Content, Annex H-2)	-	1000.00	nil
B-1( DETERMINATION OF LENGTH AND WIDTH, Annex B)	-	250.00	nil
B-2.1(DETERMINATION OF THICKNESS, Annex B )	-	0	nil
B-2.2(Determination of Thickness of the Whole Sample, Annex B)	-	0	nil
6.1(Shape)	-	300.00	nil
6.2(Dimensions)	-	250.00	nil

Complete

31 Dec, 2023

-
-

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

9250.00 View breakup
Rs.9250/- (For BIS: Rs.6938/-)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0 (chem)(MATERIAL)	-	1050.00	nil
4.6.2(TRANSPARANCY)	-	700.00	nil
4.6.3(LEAKAGE TEST)	-	1000.00	nil
4.6.4(DROP TEST)	-	1100.00	nil
4.6.5(MIGRATION TEST)	-	1700.00	nil
4.6.6(PORTABILITY TEST)	-	2900.00	nil

Complete

31 Dec, 2023

-
-

IS 13489 (2000)

Textiles – Bed mattress – Specification (first revision)

Textile Bed mattress

19200.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 c)(Thickness)	-	250.00	NIL
5.1 b)(Width)	-	0	NIL
5.1 a)(Length)	-	0	NIL
3(TYPES)	-	0	NIL
4 Table 1(MATERIALS)	-	300.00	NIL
4 Table 1 i)a) IS 175(Case)	-	0	NIL
4 Table 1 i) b)(Case)	-	0	NIL
4 Table 1 ii) a) 1S8391(Cushioning)	-	0	NIL
4 Table 1 ii) b) IS 1741(Cushioning)	-	0	NIL
4 Table 1 ii) c) IS 7933(Cushioning)	-	0	NIL
4 Table 1 iii) a) IS 1920(Piping)	-	0	NIL
4 Table 1 iv) IS 1895(Tying tapes)	-	0	NIL
4 Table 1 v) IS 1720(Sewing thread)	-	0	NIL
5(DIMENSIONS)	-	250.00	NIL
5.1 Fig. l(Type 1 Mattress)	-	0	NIL
5.2(Type 2 Mattress)	-	0	NIL
5.2 a)(Length)	-	0	NIL
5.2 b)(Width)	-	0	NIL
5.2 c)(Thickness)	-	0	NIL
6(MANUFACTURE)	-	300.00	NIL
6.1(MANUFACTURE)	-	300.00	NIL
6.2(MANUFACTURE)	-	0	NIL
6.3(MANUFACTURE)	-	0	NIL
6.4(MANUFACTURE)	-	0	NIL
6.5(MANUFACTURE)	-	0	NIL
8(PACKING)	-	0	NIL
8.2(PACKING)	-	0	NIL

Complete

31 Dec, 2023

-
-

IS 14787 (2000)

Unplasticized pvc pipes (Ducts) and fittings for underground telecommunications cable installation - Specification

- View breakup
• Rs.17150/- (For BIS: Rs.13050/-) • For PVC Resin Material (Optional): Rs.1100/- (For BIS: Rs.825/-)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

31 Dec, 2023

-
-

IS 10889 (2004)

High density polyethylene films (First Revision)

7675.00 View breakup
• For Films (Natural): Rs.6050/- (For BIS: Rs.4538) • For Raw material (Natural): Rs.2225/- (For BIS: Rs.1825/-) • For Films (Black): Rs.7675/- (For BIS: Rs.5756/-)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Grades)	-	0	nil
5.1(Materials)	-	0	nil
5.2(Black Compound)	-	0	nil
6.1.1(Appearance)	-	300.00	nil
6.1.2(Film Form)	-	0	nil
6.1.3(Odour )	-	0	nil
6.1.4(Density)	-	500.00	nil
6.1.5(Melt Flow Rate)	-	1100.00	nil
6.1.6(Black Film)	-	1625.00	nil
6.2.1, Table 1(Nominal Thickness)	-	250.00	nil
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.2.2, Table 2(Nominal Width)	-	250.00	nil
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.3, Table 3(Yield Tolerance)	-	600.00	nil
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.4.1(Tensile Strength at Break)	-	2200.00	nil
6.4.1, Table 4(Direction)	-	0	nil
6.4.1, Table 4(Grade 1 and 2)	-	0	nil
6.4.2(Elongation at Break)	-	0	nil
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	0	nil
6.4.3(Impact Resistance (Falling Dart))	-	850.00	nil
6.4.3, Table 6(Average Thickness of Film)	-	0	nil
6.4.3, Table 6(Impact Failure Load)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 15609 (2005)

Polyethylene flexible pouches for the packing of natural mineral water and packaged drinking water - Specification

14000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.5 Annex J(Product resistance test for printed pouches)	-	500.00	nil
7.4 Annex H(Ink adhesion test for printed pouches)	-	500.00	nil
7.3 Annex G(Drop test )	-	1100.00	nil
7.2 Annex F(Stack Load test)	-	900.00	nil
7.1 Annex E(Water Potability test (after 30 Days) a) Taste b) Odour)	-	2900.00	nil
6.1.10 Annex -6 of IS:2508:2016(Dart impact Resistance)	-	850.00	nil
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - b. Crosswise direction)	-	1100.00	nil
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - a. Lengthwise direction)	-	0	nil
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength b. Crosswise direction)	-	1100.00	nil
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength a. Lengthwise direction)	-	0	nil
6.1.7 IS: 9845:1998(Migration- a. Amount of extractive )	-	1700.00	nil
6.1.6(Width)	-	250.00	nil
6.1.5 A-2 of IS: 2508:2016(Thickness)	-	250.00	nil
6.1.4(Odour)	-	500.00	nil
6.1.3(Winding of the Film )	-	0	nil
6.1.2(Film Form)	-	0	nil
6.1.1(Description)	-	0	nil
5(Material)	-	1050.00	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	575.00	nil
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	500.00	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

1744.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	500.00	nil
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	500.00	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	500.00	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

1819.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 2, table 2(Dimensions)	-	500.00	nil
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500.00	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

1744.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.3, 3.3.1, Fig 1(Manufacture)	-	0	nil
3.3.2, table 1, fig 1(Dimensions)	-	500.00	nil
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	0	nil
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	500.00	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 2(Manufacture)	-	0	nil
3.2.2, Fig 2, table 2(Dimensions)	-	500.00	nil
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500.00	nil
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	0	nil
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 2(Manufacture)	-	0	nil
3.2.2, Fig 1, table 1(Dimensions)	-	500.00	nil
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500.00	nil
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	0	nil
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 2(Manufacture)	-	0	nil
3.2.2, Fig 1, table 1(Dimensions)	-	500.00	nil
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500.00	nil
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 45o Bend)	-	0	nil
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	500.00	nil
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	500.00	nil
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	0	nil
3.2.3(Socket, Measurement)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

52050.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	500.00	nil
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0	nil
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0	nil
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	nil
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	300.00	nil
7.2(Physical characteristics for pipes and fittings )	-	0	nil
7.3(Physical characteristics for pipes and fittings )	-	0	nil
8.1.1(Mechanical Characteristics of Pipes General)	-	300.00	nil
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1100.00	nil
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1100.00	nil
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	nil
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	nil
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	nil
8.3(Joints)	-	300.00	nil
5.1(Composition of the material)	-	0	nil
6.3(Dimensions of pipes and fittings)	-	500.00	nil
6.3.1 Table 2(Mean outside diameter)	-	0	nil
7.4(Resistance to Dichloromethane)	-	1000.00	nil
7.5(longitudinal reversion)	-	1000.00	nil
8.1(Appearance and colour)	-	300.00	nil
8.2(Vicat softening temperature of fittings)	-	1100.00	nil
8.3(Effect of Heating (Stress Relief Test))	-	700.00	nil
9.1(Ring stiffness)	-	1400.00	nil
9.2(Resistance to external blows at o C)	-	1400.00	nil
9.3(Ring flexibility)	-	1100.00	nil
9.4(Creep ratio)	-	26300.00	nil
10.1(Impact Strength of Injection Moulded and Fabricated Fittings)	-	1100.00	nil
11.1(Elastomeric Sealing Rings)	-	0	nil
11.2(Solvent cement)	-	1150.00	nil
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water pressure))	-	1150.00	nil
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vaccum ))	-	2300.00	nil
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	39000.00	nil
12.2.1(Tightness of Solvent cemented Ring Joints )	-	1000.00	-
12.2.2(Tightness of Solvent cemented Ring Joints (Vaccum pressure))	-	2300.00	nil

Complete

31 Dec, 2023

-
-

IS 9755 (2016)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing fertilizers – Specification (fifth revision)

21810.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	300.00	nil
3.4(Liner-The thickness(A-2 of IS 2508) shall be 40 μm ± 10 percent in case of HMHDPE/ HDPE.)	-	500.00	nil
3.5(Bottom Seam-The two rows of stitches shall be separated from each other by minimum 5 mm)	-	0	nil
3.6(Bottom Seam-the outer stitch shall be minimum 8 mm from the outer edge of the sacks.)	-	0	nil
3.4(Liner-The width of the loose liner shall be minimum 20 mm more than the width of the sack.)	-	250.00	nil
3.4.2(Liner-The bottom seal of the loose liner shall be at least 25 mm from the bottom edge.)	-	250.00	nil
3.6(Bottom Seam-tThe stitching shall be done with double fold over seam to a depth of minimum 25 mm, so that the stitches pass through a minimum of six layers of the fabric.)	-	0	nil
3.3(Sacks)	-	300.00	nil
3.4(Liner)	-	500.00	nil
3.4.2(Lamination)	-	1800.00	nil
3.7(Mouth of the Sack)	-	250.00	nil
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	250.00	nil
4.3(Mass-(Annexure E))	-	250.00	nil
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	500.00	nil
4.1 , Table 1(REQUIREMENTS)	-	3800.00	nil
4.2(UV Resistance)	-	10460.00	nil

Complete

31 Dec, 2023

-
-

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

48013.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4( Line/ Cord beading IS 7903)	-	250.00	nil
4.0(Types IS 7903)	-	500.00	nil
5.1.1(Lamination IS 7903)	-	1050.00	nil
5.1.2(Lamination IS 7903)	-	0	nil
5.2.1(Construction IS 7903)	-	250.00	nil
5.3(Joint/Seam, IS 7903)	-	400.00	nil
5.4(Fixing of Eyelets, IS 7903)	-	0	nil
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	250.00	nil
6.1 Table 1,ii)(No of lamination layers, IS 7903)	-	0	nil
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	250.00	nil
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	2700.00	nil
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	0	nil
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	28900.00	nil
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	1100.00	nil
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	1100.00	nil
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	1100.00	nil
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	1100.00	nil
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	850.00	nil
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	950.00	nil
6.2(Length, IS 7903)	-	250.00	nil
6.2(Width, IS 7903)	-	250.00	nil
6.2(height, IS 7903)	-	250.00	nil
6.3(Water Proofness,IS 7941)	-	1000.00	nil
6.3(Water Proofness, IS 7940)	-	5200.00	nil
3.3(Eyelets (Dimesnions) i) Starting thickness of metal Aluminium min ii) Outside dia of flange‘A’ iii) Flange formed height ‘B’ iv) Pierced dia ‘C’ v) Overall length ‘D’ vi) Internal dia of Barrel when closed ‘E’ min vii) Thickness of compressed material between eyelet and washer F’ max viii) Outside diameter of barrel under the flange‘G’ )	-	250.00	nil
3.2(HDPE Fabric (Material Identification))	-	1050.00	nil
3.1(HDPE Tapes (Carbon Black Content))	-	925.00	nil
3.1(HDPE Tapes (Material Identification))	-	1050.00	nil
5.1.1(Coating Thickness)	-	250.00	nil
5.1.1(Carbon Black Content)	-	925.00	nil
5.1.1(Sandwich lamination thickness)	-	250.00	nil
5.1.1(Mass of Finished Tarpaulin)	-	500.00	nil
5.1.1(UV Exposure (144 hrs))	-	26700.00	nil
5.1.1(Agening)	-	4200.00	nil

Complete

31 Dec, 2023

-
-

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

7913.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	250.00	nil
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	250.00	nil
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	250.00	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	500.00	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	500.00	nil
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	nil
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	nil
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	nil
4.1(Raw Material )	-	1050.00	nil
4.2 (Fabric)	-	300.00	nil
4.2 (Linear Density, 900 denier)	-	500.00	nil
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	500.00	nil
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	nil
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	500.00	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	nil
4.3(Sacks)	-	500.00	nil
4.4(Seam )	-	250.00	nil
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	nil
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	nil
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	nil
4.4(to a depth of minimum 25 mm, so that so that)	-	0	nil
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	nil
4.4(The number of stitches/dm shall be 14 ± 2.)	-	250.00	nil
4.4(Seam)	-	0	nil
4.5(Lamination )	-	1050.00	nil
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	400.00	nil
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	500.00	nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	2200.00	nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	nil
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	2200.00	nil
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	nil
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	nil
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100.00	nil
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	950.00	nil
5/5.6 (UV Resistance, )	-	10180.00	nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	2200.00	nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	1100.00	nil

Complete

31 Dec, 2023

-
-

IS 12650 (2018)

Textiles – Jute bags for packing 50 kg foodgrains – Specification (third revision)

7400.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-4.2(Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-	250.00	nil
4-4.3(Manufacture-Safety Stitch-The number of safety union stitches per decimetre shall be10 ± 1.)	-	0	nil
4-4.1(MANUFACTURE- The bags shall be made from single piece of twill weave jute sacking of uniform construction having nominal mass of 579 g/m2 as given below with warp running along the length of the bag:)	-	300.00	nil
4-4.1-a)(MANUFACTURE)	-	0	nil
4-4.4(Manufacture-Hemming at the Mouth )	-	0	nil
4-4.5(Manufacture- Freedom from Defects )	-	0	nil
5-5.1-Table 1-Sr. no. i)(SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 a) Out side Length , cm 94 (For both type A & Type B) Tolerance + 4 / -0 cm)	-	500.00	nil
5-5.1-Table 1-Sr. no. i)(SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 b) Outside width, cm 57 (For both type A & Type B) Tolerance + 4 / -0 cm)	-	500.00	nil
5-5.1-Table 1-Sr. no.i i)(SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Ends/dm Type A 46 + 2 /Type B 76 + 4 / -3)	-	0	nil
5-5.1-Table 1-Sr. no.iii)(SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Picks/dm Type A 50 (2 x 25) / Type B 28 + 2)	-	0	nil
5-5.1-Table 1-Sr. no.iv)(SPECIFIC REQUIREMENTS-Cl. 8.5.2 of IS 9113 Corrected Mass/bag, g ( See Note 2) For both Type A & Type B 665 + 8.0 / -6.0 percent)	-	500.00	nil
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): a ) Warpway- 1570 (160) for both type A & Type B)	-	1100.00	nil
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): b ) Weftway- 1420 (145) for both type A & Type B)	-	1100.00	nil
5-5.1-Table 1-Sr. No.vi)(SPECIFIC REQUIREMENTS-Cl. 8.7 of IS 9113 Average side seam strength (5 cm ×20 cm raveled strip), Min, N (kgf): 490 (50) for both type A & Type B)	-	1100.00	nil
5-5.1-Table 1-Sr. No.vii)(SPECIFIC REQUIREMENTS-Cl. 8.2 of IS 9113 Moisture regain, percent, Max (see Note 3) 22 for both type A & Type B)	-	1000.00	nil
5-5.1-Table 1-Sr. No.viii)(SPECIFIC REQUIREMENTS-Cl. 8.8 of IS 9113 Oil content on dry de-oiled material, Max 3 for both type A & Type B)	-	1000.00	nil

Complete

31 Dec, 2023

-
-

IS 8391 : Part 3 (2019)

Rubberized coir sheets for cushioning – Specification Part 3 Sandwiched (third revision)

- View breakup
Rs.14700/- (For BIS: Rs.11613/-)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

31 Dec, 2023

-
REVISED VERSION OF IS 8391(Pt-3):2019 included.

IS 11584 (1986)

Specification for high density polyethylene (Hdpe) crates for milk satchets

7838.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2(Material )	-	1050.00	nil
2.3(Shape and Dimensions)	-	500.00	nil
2.4(Mass )	-	300.00	nil
2.5(Appearance and Surface Finish)	-	300.00	nil
2.6(Colour Fastness)	-	300.00	nil
2.7(Resistance to Stress)	-	1000.00	nil
2.8(Resistance to Applied Load)	-	1000.00	nil
2.9(Strength)	-	1000.00	nil
2.1(Dimensional Stability)	-	900.00	nil

Complete

31 Dec, 2023

-
-

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

5625.00 View breakup
Rs.5625/- (For BIS: Rs.4219/-)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	500.00	nil
table 1 sl.no: 02(20 )	-	0	nil
table 1 sl.no: 03(25 )	-	0	nil
table 1 sl.no: 04(32 )	-	0	nil
table 1 sl.no: 05(40 )	-	0	nil
table 1 sl.no: 06(50 )	-	0	nil
table 1 sl.no: 07(63 )	-	0	nil
table 1 sl.no: 08(75 )	-	0	nil
table 1 sl.no: 09(90 )	-	0	nil
table 1 sl.no: 10(110 )	-	0	nil
table 1 sl.no: 11(125 )	-	0	nil
table 1 sl.no: 12(140 )	-	0	nil
table 1 sl.no: 13(160 )	-	0	nil
table 1 sl.no: 14( 180 )	-	0	nil
table 1 sl.no: 15(200 )	-	0	nil
table 1 sl.no: 16(225 )	-	0	nil
table 1 sl.no: 17(250.0)	-	0	nil
table 1 sl.no: 18(280.0)	-	0	nil
table 1 sl.no: 19(315.0)	-	0	nil
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	500.00	nil
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	0	nil
2.2.3( inside diameter of the socket)	-	0	nil
2.2.3(socket length)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

5625.00 View breakup
Rs.5625/- (For BIS: Rs.4219/-)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	500.00	nil
table 1 sl.no: 02(20 )	-	0	nil
table 1 sl.no: 03(25 )	-	0	nil
table 1 sl.no: 04(32 )	-	0	nil
table 1 sl.no: 05(40 )	-	0	nil
table 1 sl.no: 06(50 )	-	0	nil
table 1 sl.no: 07(63 )	-	0	nil
table 1 sl.no: 08(75 )	-	0	nil
table 1 sl.no: 09(90 )	-	0	nil
table 1 sl.no: 10(110 )	-	0	nil
table 1 sl.no: 11(125 )	-	0	nil
table 1 sl.no: 12(140 )	-	0	nil
table 1 sl.no: 13(160 )	-	0	nil
table 1 sl.no: 14( 180 )	-	0	nil
table 1 sl.no: 15(200 )	-	0	nil
table 1 sl.no: 16(225 )	-	0	nil
table 1 sl.no: 17(250.0)	-	0	nil
table 1 sl.no: 18(280.0)	-	0	nil
table 1 sl.no: 19(315.0)	-	0	nil
2.1(General)	-	500.00	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	0	nil
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	nil
2.2.3( inside diameter of the socket)	-	0	nil
2.2.3(Socket length)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

4219.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	0	nil
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	500.00	nil
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	500.00	nil
2.2.3( inside diameter of the socket)	-	500.00	nil
2.2.3(Socket length)	-	0	nil

Complete

31 Dec, 2023

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

4219.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	0	nil
2.2.2, Table 1(Socket Laying Length)	-	500.00	nil
2.2.3( inside diameter of the socket)	-	500.00	nil
2.2.3(Socket length)	-	0	nil

Complete

31 Dec, 2023

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

CIPET, Bhubaneswar

B/25, C.N.I complex, Patia, Bhubaneswar, BHUBANESWAR, Khordha, Odisha, 751024

7566177001 [email protected]

Scope List

No Record Found

No Record Found