BIS - LIMS (Laboratory Information Management System)

Shri Krishna Test House

B-70/1, Gali no 8 , New modern Shahdara ,Near DDA Flats mansarover park shahdara, Delhi, Shahdara, Delhi, 110032

9891112786 [email protected]

Scope List

Reset

36 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 17150 (2019)

Mini domestic water heater for use with piped natural gas (PNG) ? specification

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(The construction of all the parts of equipment shall be sound and of high standard of workmanship and appropriate finish. The construction shall ensure durability and shall comply with the safety requirements.)	-	200	NA
4.1(Rivets, Fastening screws and plugs , etc. shall not lead into gas passages.)	-	200	NA
4.1.1(No PNG regulator shall be included as a part of the instantaneous domestic gas water heater.)	-	200	NA
4.1.2(All parts in contact with water shall be made of such a material that shall not pollute water.)	-	200	NA
4.1.3(All Parts shall be made and so assembled that the performance characteristics of the appliance will not alter significantly during reasonable life and in normal conditions of installation and use.)	-	200	NA
4.1.4(it shall be possible to clean without difficulty)	-	200	NA
4.1.5(It shall not be possible to replace to replace parts, which are removable for maintenance in a way that could impair the safe performance of the appliance.)	-	200	NA
4.1.6(The gas and water soundness shall be assured after reassemble maintenance.)	-	200	NA
4.1.7(it shall be possible to install an appliance intended to be fixed to a wall with appropriate means of fixing, such as clamps, hooks, Screws, etc. )	-	200	NA
4.1.8(All parts of gas water heaters subject to direct heat shall have brazed or welded joints.)	-	200	NA
4.1.8(Interior surfaces shall be of such material or so protected, so as to avoid contamination of the contents.)	-	200	NA
4.1.9(The gas (heat) input to the pilot alone shall not exceed 8 l/h at a gas inlet pressure of 21 mbar and at temperature 25-30°C, wherever applicable.)	-	200	NA
4.1.10(The Appliance shall be provided with a safety device, which cuts off the supply of gas in case water dose not flow or stops flowing while in operation.)	-	200	NA
4.1.11(The water heater shall have a provision such that supply of gas shall be cut off and the burner extinguished after 20+1/-2 min of uninterrupted use. The appliance shall able to restart manually.)	-	200	NA
4.1.12(All heat exchanger tubes through which the water passes and water chamber, if provided, shall be completely filled with water before igniting the burner.)	-	200	NA
5.1(The material used in the construction of the water heater shall be resistant to wear and deterioration occuring in the normal use.)	-	500	NA
5.2(The copper and copper alloy forged and cast parts shall pass the mercurous nitrate test (Season cracking test) when tested according to the method specified in IS:2305.)	-	500	NA
5.3(Change in weight or volume of a non metallic material, when immerse in n-Pentane for 72 hours)	-	500	NA
5.4(Melting point of metal for burner top)	-	500	NA
5.5(Diaphragm if provided for inlet water control device, shall be made of synthetic rubber.while choosing the material, the manufacturer shall take into account the characteristics required for the satisfactory use that is , mechanical and chemical stability. Material selected shall not degrade under normal working conditions.)	-	500	NA
6.1(For connections and screws other than for water, metric threads shall be used. )	-	500	NA
6.2(Gas inlet connection shall permit a rigid connection.)	-	500	NA
6.2(Gas inlet connection shall permit a rigid connection.)	-	500	NA
6.3(All water connection shall be of copper or brass tube and have at least 6 mm inner diameter and 0.5 mm nominal wall thickness of the tube.)	-	500	NA
6.4(The water inlet and outlet connection shall be of 1/2" BSP thread.)	-	500	NA
6.5(The gas and water connections shall be situated at the base of the appliance. it shall be possible to connect the appliance to supply, which are in a plane parallel or perpendicular to the wall on which the appliance is fixed.)	-	500	NA
6.6(Gas Inlet Connections : The water heater shall be provided with nozzle or screwed gas inlet connection as given in 18 of IS:5116)	-	500	NA
7(All Appliances shall be designed so that ignition, correct burner performance and the length of the pilot flames. If any , can always be easily seen. This visibility shall be assumed at all times and particularly, where there is a viewing window, this shall not deteriorate under the effect of heat.)	-	1000	NA
8(The Appliance shall have a device allowing manual interruption of the supply of gas to the burner and pilot, if available in case of exigency.)	-	500	NA
8(The device shall be of such a design that gas shall not enter to the main burner and the pilot (if provided) until it is reset to the original position.)	-	500	NA
9.1(The Appliance shall have a flame failure device, controlling the admission of gas to the main burner and possibly to any ignition pilot. The provisions given in 14.1 of IS:5116 shall apply.)	-	1000	NA
10(An appliance shall have an ignition device, where the appliance is provided in the form of a pilot it shall be possible to light it easily with a matchstick or a special ignition device)	-	500	NA
10(The pilot shall be positioned in such a way that their products of combustion are evacuated with those of the burner)	-	500	NA
10(While in operation the relative position of the pilot and burner shall not alter.)	-	500	NA
10(The pilot burner shall be made of a material that shall not deteriorate under normal condition of use)	-	500	NA
10(It is essential that the pilot flame shall be seen either directly or by reflection.)	-	500	NA
10(The ignition to the burners from pilot shall be smooth)	-	500	NA
11(The Water heater shall be provided with a suitable overheat protection device, which shall switch off the supply of gas, if the temperature of the delivered water reaches 80°C max. )	-	1000	NA
11(The gas supply shall be restored manually.)	-	1000	NA
12(The Appliance shall be provided with a means of adjusting water rate.)	-	1000	NA
14(All gas carrying parts of the appliances should be sound and these parts when connected to form complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m²)	-	1000	NA
15(All water carrying parts of the appliance, individually and when assembled to form the water circuit of the appliance shall not leak or show any permanent distortion during or after the test when tested at a hydrostatic pressure 4 kgf/cm2)	-	500	NA
15(The later circuit shall be kept under pressure for minimum 5 min.)	-	500	NA
16(Thermal efficiency of Water Heater shall not be less nthan 62%)	-	1000	NA
17(Ratio of Carbon Monoxide to Carbon Dioxide)	-	1000	NA
18( (D = Declared Value, Gas Consumption)	-	1000	NA
19.1(There shall be easy and safe access of lighting each burner by matchstick and it shall be easy to see that the burner is lighted)	-	400	NA
19.2(if the flame is applied to any one burner pors when the gas is flowing , flame travel shall be complete. This applies for all pressures from 20 to 25 gf/cm² taps being fully open.)	-	400	NA
19.3(if the burner is ignited from a pilot flame , ignition shall be smooth at pressure from 20-25 gf/cm² with the tap turned full on and ignition shall be effected without delay after turning on the taps.)	-	200	NA
20(It shall be possible to operate the appliance with taps fully open at gas inlet pressure , without the flame extinguishing, blowing off or striking back and without the formation of soot.)	-	500	NA
20(Pilot Flame shall be Stable without lifting or soot deposition at gas inlet pressure from 20-25 gf/cm2)	-	500	NA
21(Ignition of Burner flame, their operation and turning off shall not give rise to undue excessive noise during the operation.)	-	1000	NA
22(While the appliance is in operation at full gas consumption and the appliance is in thermal equilibrium, the flame shall be immediately reduced to the minimum possible and then brought back to the full size, the operation shall be repeated five times, no flash back shall occur during the test, applicable for pressure 20-25 gf/cm².)	-	1000	NA
23(There shall be no extinction of flame on any of the burner operating at the maximum consumption when the appliance is placed in a normal current of air with velocity of 2 m/s as measured with a rotating vane anemometer. The location of the appliance relative to the neighbouring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation, applicable for all pressure 20-25 gf/cm².)	-	1000	NA
24(Wall, Floor, Ceiling temperatures: Rise of Temperature above room temperature in , after two hours of operation)	-	250	NA
24(Surface temperature:Temperature of the portion of the surface other than the working surface likely to be touched accidentally.)	-	250	NA
24(Temperature of the surface in normal use)	-	250	NA
24(Temperature of synthetic rubber diaphragm in gas carrying components)	-	250	NA
25(When tested as per annex D, at the nominal gas rate with the appliance adjusted to give a temperature rise of 45±5°C between the water inlet and outlet , the time to achieve 90% of this temperature rise-)	-	1000	NA
26(Hot water output, Declared Value)	-	1000	NA

Complete

05 Oct, 2022

-
-

IS 14756 (2017)

Stainless steel cookware - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1 & Table 1 of IS 5522 (Carbon)	-	0	NA
3.1 & Table 1 of IS 5522 (Silicon)	-	0	NA
3.1 & Table 1 of IS 5522 (Manganese)	-	0	NA
3.1 & Table 1 of IS 5522 (Nickel)	-	0	NA
3.1 & Table 1 of IS 5522 (Chromium)	-	0	NA
3.1 & Table 1 of IS 5522 (Sulphur)	-	0	NA
3.1 & Table 1 of IS 5522 (Phosphorus)	-	0	NA
3.1 & Table 1 of IS 5522 (Copper)	-	0	NA
3.1 & Table 1 of IS 5522 (Nitrogen)	-	0	NA
4.1(Shape and Dimension,)	-	700	NA
4.2(Thickness)	-	500	NA
5.1(Workmanship And Finish)	-	200	NA
5.2(Workmanship And Finish)	-	200	NA
5.3(Workmanship And Finish)	-	200	NA
5.4(Workmanship And Finish)	-	200	NA
6.1(Staining Test)	-	3000	NA
6.2(Mechanical Shock Test (for cladded utensils only))	-	1500	NA
6.3(Thermal Shock Test (for cladded utensils only))	-	1500	NA
6.4(Dry Heat Test (for cladded utensils only))	-	1000	NA
6.4(Dry Heat Test (for cladded utensils only))	-	1000	NA

Complete

05 Oct, 2022

-
-

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1, 8.1.1 & 10.1 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	550	10% Discount to BIS
6(Freedom From Defects)	-	50	10% Discount to BIS
9.3(Tensile Test-1608:Part 1)	-	750	10% Discount to BIS
9.3, Table 3 (Yield Strength, Mpa)	-	750	10% Discount to BIS
9.3, Table 3 (Tensile Strength, Mpa)	-	750	10% Discount to BIS
9.3, Table 3 (Elongation, %)	-	750	10% Discount to BIS
9.4(Erichsen Cupping Test,(Average depth of cupping) mm)	-	750	10% Discount to BIS
11(Surface finish)	-	250	10% Discount to BIS
12(Dimensions)	-	250	10% Discount to BIS
14.1(Thickness,mm)	-	150	10% Discount to BIS
14.2( Width, mm)	-	150	10% Discount to BIS
14.3(Length, mm)	-	150	10% Discount to BIS
14.4(Flatness, mm)	-	150	10% Discount to BIS
14.5(Camber, mm)	-	150	10% Discount to BIS

Complete

05 Oct, 2022

-
-

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(General)	-	100	10% Discount to BIS
Clause 4.2(Material)	-	100	10% Discount to BIS
Clause 4.2.1(Lining)	-	100	10% Discount to BIS
Clause 4.2.2 (a)(Reinforcement)	-	100	10% Discount to BIS
Clause 4.2.2 (b)(Reinforcement)	-	100	10% Discount to BIS
Clause 4.2.3(Cover)	-	100	10% Discount to BIS
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	290	10% Discount to BIS
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	400	10% Discount to BIS
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	200	10% Discount to BIS
Clause 4.3 Sub Clause 4.3.3(Length)	-	500	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	500	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	500	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	500	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	500	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	500	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	500	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	1200	10% Discount to BIS
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	1200	10% Discount to BIS
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	750	10% Discount to BIS
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1500	10% Discount to BIS
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	300	10% Discount to BIS
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2500	10% Discount to BIS
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	700	10% Discount to BIS
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	700	10% Discount to BIS
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	500	10% Discount to BIS
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	500	10% Discount to BIS
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	20	10% Discount to BIS
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	20	10% Discount to BIS
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	20	10% Discount to BIS
Clause 5.2 (d)(Marking Batch/Lot No. )	-	20	10% Discount to BIS
Clause 5.2 (e)(Marking Month and year of manufacture )	-	20	10% Discount to BIS
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	20	10% Discount to BIS
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	20	10% Discount to BIS
Clause 5.2.1(BIS Certification Marking )	-	20	10% Discount to BIS

Complete

05 Oct, 2022

-
-

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

All Size

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 5.2.1(BIS Certification Marking )	-	10	NA
Clause 5.2 (f)(Marking IS 9573 (Part 1) )	-	10	NA
Clause 5.2 (e)(Marking Month and year of manufacture )	-	10	NA
Clause 5.2 (d)(Marking Batch/Lot No. )	-	10	NA
Clause 4.1 (General)	-	100	NA
Clause 4.1(General)	-	100	NA
Clause 4.2(Material)	-	100	NA
Clause 4.2.1(Lining)	-	100	NA
Clause 4.2.2(Reinforcement)	-	100	NA
Clause 4.2.3(Cover)	-	100	NA
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	100	NA
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	100	NA
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	100	NA
Clause 4.3 Sub Clause 4.3.3(Length)	-	100	NA
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1000	NA
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	1000	NA
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	1000	NA
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- cover)	-	1000	NA
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	600	NA
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	400	NA
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	400	NA
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	400	NA
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	400	NA
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	400	NA
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	930	NA
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	2000	NA
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	800	NA
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	1500	NA
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	600	NA
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	500	NA
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	500	NA
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	500	NA
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	10	NA
Clause 5.2 (b)(Marking Words LPG, Max W.P. 2.5 MPa; )	-	10	NA
Clause 5.2 (c)(Marking Nominal bore )	-	10	NA

Complete

05 Oct, 2022

-
-

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Freedom from Defects)	-	150	NA
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	150	NA
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	1000	NA
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	500	NA
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	200	NA
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	400	NA
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	400	NA

Complete

05 Oct, 2022

-
-

IS 366 (1991)

Electric iron - Specification (Fourth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Classification (as per Cl.6 of IS 302-2-3 and Cl.6.1 of IS 302-1))	-	1000	NA
7.0(Classification (as per Cl.6 of IS 302-2-3 and Cl.6.2 of IS 302-1))	-	500	NA
9.0(Protection against access to live parts (as per Cl. 8 of IS 302-2-3 and IS 302-1))	-	500	NA
9.0(Power input and current (as per Cl. 10 of IS 302-2-3 and IS 302-1))	-	500	NA
9.0(Temperature Rise (as per Cl. 11 of IS 302-2-3 and IS 302-1))	-	300	NA
9.0(Leakage current and Electric Strength at Operating Temperature (as per Cl. 13 of IS 302-2-3 and IS 302-1))	-	200	NA
9.0(Transient Overvoltage (as per of Cl. 14 of IS 302-2-3 and Table 6 of IS 302-1))	-	500	NA
9.0(Moisture Resistance (as per of Cl.15 of IS 302-2-3 and IS 302-1))	-	300	NA
9.0(Abnormal Operation (as per of Cl.19 of IS 302-2-3 and IS 302-1) )	-	200	NA
9.0(Staibilty and mechanical hazards (as per of Cl.20 of IS 302-2-3 and IS 302-1) )	-	300	NA
9.0(Mechanical strength (as per of Cl.21 of IS 302-2-3 and IS 302-1) )	-	300	NA
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	400	NA
9.0(Internal wiring (as per of Cl.23 of IS 302-2-3 and IS 302-1) )	-	300	NA

Complete

05 Oct, 2022

-
-

IS 8978 (1992)

Specification for electric instantaneous water heaters (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7 of IS 302-2-35:2017(Marking)	-	1000	NA
Cl.6 of IS 302-2-35:2017(Classification)	-	1000	NA
Cl.8 of IS 302-2-35:2017(Protection Against Access To Live Parts)	-	1000	NA
Cl.10 of IS 302-2- 35:2011(Power Input & Current )	-	1000	NA
Cl.11 of 302-2-35:2017(Heating)	-	1000	NA
Cl.13 of IS 302-2-35:2017(Leakage Current & Electrical Strength at Operating Temperature )	-	1000	NA
Cl.14 of IS 302-2-35:2017(Transient Over Voltages )	-	1000	NA
Cl.15 of IS 302-2-35-2011(Moisture Resistance )	-	1000	NA
Cl.16 of IS 302-2-35:2011(Leakage Current and Electric Strength)	-	200	NA
Cl.17 IS 302-2-35:2017(Overload Protection of Transformers & Associated circuits )	-	200	NA
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	200	NA
Cl.20 of IS 302-2-35-2011(Stability & Mechanical Hazards )	-	500	NA
Cl.21.1 of IS 302-2-35-2011(Mechanical strength)	-	200	NA
Cl.22 of IS 302-2-35-2011(Construction )	-	500	NA
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	400	NA
Cl.24 of IS 302-2-35:2017(Component )	-	500	NA
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	500	NA
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	500	NA
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	500	NA
Cl.28 of IS 302-2-35:2017(Screws and Connections )	-	500	NA
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	500	NA
Cl.7 of IS 302-2-35:2017(Marking)	-	200	NA

Complete

05 Oct, 2022

-
-

IS 6603 (2001)

Stainless steel bars and flats - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Carbon -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	500	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Silicon- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Manganese- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Nickel -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Chromium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Molybdenum- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Titanium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Niobium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Sulphur- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Phosphorus- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Others (Nitrogen)- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	550	NA
Cl.14.1(Corrosion Resistance- IS 10461(Part1))	-	1400	NA
6(Freedom from defects:)	-	200	NA
9.1, Table 3(0.2 Percent Proof Stress, MPa)	-	400	NA
9.2, Table 3(Tensile Strength, MPa)	-	700	NA
9.3, Table 3(Elongation ,Percent)	-	300	NA
9.4, Table 3(Annealed Hardness, HB-IS 1500: Pt 1)	-	400	NA
9.5, Table 3(Charpy Impact Test, J-IS 1499)	-	300	NA
12(Dimensions & Tolerances, mm-IS 6603)	-	100	NA
12(Diameter, mm)	-	50	NA
12(Out of Round , mm)	-	50	NA
12(Length , mm)	-	50	NA
12(Variation in Straightness)	-	50	NA

Complete

05 Oct, 2022

-
-

IS 4159 (2002)

Mineral filled sheathed heating elements - Specification (Third Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6 of IS 4159:2002 & IS 302-1:2008 (Classification)	-	0	NA
Cl.7 of IS 4159:2002 & IS 302-1:2008(Marking )	-	0	NA
Cl.8 of IS 4159:2002 & IS 302‐1:2008(Protection Against Electric Shock)	-	300	NA
Cl.10 of IS 4159:2002 & IS 302-1:2008(Input & Current)	-	700	NA
Cl.11 of IS 4159:2002 & IS 302‐1:2008(Temperature Rise)	-	1000	NA
Cl.13 of IS 4159:2002 & IS 302-1: 2008(Electrical Insulation and Leakage Current at Operating Temperature)	-	250	NA
Cl.15 of IS 4159:2002 & IS 302-1: 2008(Moisture Resistance)	-	1000	NA
Cl.16 of IS 4159:2002 & IS 302-1: 2008(Insulation Resistance & Electric Strength (after Humidity Treatment))	-	250	NA
Cl.18 of IS 4159:2002(Endurance Test )	-	0	NA
Cl.19 of IS 4159:2002 & IS 302-1: 2008(Abnormal Operation)	-	200	NA
Cl.20 of IS 4159:2002 & IS 302-1: 2008(Stability & Mechanical Hazards )	-	300	NA
Cl.21 of IS 4159:2002 & IS 302-1: 2008(Mechanical Strength)	-	500	NA
Cl.22 of IS 4159:2002 & IS 302-1: 2008(Construction)	-	100	NA
Cl.23 of IS 4159:2002 & IS 302-1: 2008(Internal Wiring )	-	0	NA
Cl.24 of IS 4159:2002 & IS 302-1: 2008(Component )	-	100	NA
Cl.25 of IS 4159:2002 & IS 302-1: 2008(Supply connection & external flexible cables & cords)	-	100	NA
Cl.26 of IS 4159:2002 & IS 302-1: 2008(Terminals for External Conductors)	-	0	NA
Cl.27 of IS 4159:2002 & IS 302-1: 2008(Provision for Earthing)	-	400	NA
Cl. 29 of IS 4159:2002 & IS 302-1: 2008(Creepage Distances & Clearances)	-	400	NA
Cl. 30 of IS 4159:2002 & IS 302-1: 2008(Resistance to Heat, Fire and Tracking)	-	1500	NA
Cl. 31 of IS 4159:2002 & IS 302-1: 2008(Resistance to Rusting)	-	1500	NA
Cl. 33.1 of IS 4159:2002(Finish Test )	-	0	NA
Cl. 102 of IS 4159:2002(Leakage & Hydrostatic Strength Test (for Oil heating elements) )	-	0	NA

Complete

05 Oct, 2022

-
-

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.24(Annexure E)(on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-	900	NA
Cl.23(There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-	300	NA
Cl 22(A vessel, 150 mm diameter, full of water, shall be placed on the burner and the burner lighted at ‘ON’ position of the tap for one hour. After the test, no soot (unburned carbon) shall be deposited on the burner and on the bottom of the vessel. This applies for all pressures from 2452 kN/m2 to 3432 kNlm2 (25 gf/cm2 to 35 gf/cm2))	-	500	NA
Cl 21(When operated at pressures 25-35 gmf/cm² there shall be no extinction of flame on any of the burner operating at the maximum of the burner when the appliance is placed in thenormal current of air with the velocity of 2 m/s as measured with a rotating vane anemometer.)	-	300	NA
Cl.20(The ignition of the burner flames, their operation and turning ‘OFF’ shall not give rise to undue or excessive noise during all the operations.)	-	200	NA
Cl19.3(The fixed minimum pilot rate shall be sufficient to relight the main burnerat2452 kN/m2 (25 gf/cm2) gas inlet pressure.)	-	200	NA
Cl 19.2(Pilot flames shall be stable, without lifting or soot deposition, at gas inlet pressure from 2 452kN/m2to3432 kN/m2 (25 gf/cm2 to 35 gf7cm2).)	-	100	NA
Cl 19.1.1(When the gas consumption of a burner is reduced to simmer after operating for half an hour at full ‘ON’, the flame shall not extinguish, blow off, strike back or form soot when tested with commercial LPG at 2942 kN/m2 (30 gf/cm2) gas inlet pressure.)	-	200	NA
Cl 19.1(It shall be possible to operate the appliance with taps fully open at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gflcmz to 35 gf/cm2) without the flame extinguishing, blowing off or striking back and without the formation of soot)	-	100	NA
Cl18.4 (Cl14 of IS 5116)(Shall be protected against adjustment by unauthorized persons.)	-	200	NA
Cl18.3(When the burner is ignited from a pilot flame and / or by an electric/electronic method, the ignition and flame travel shall be smooth at pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2) with the burner tap turned full ‘ON’ and ignition shall be effected without undue delay after turning on taps)	-	100	NA
cl 18.2(If a flame is applied to any of the outer row of the burner ports when the gas is flowing, flame travel shall be complete. This applies for the all pressures from 2452 to 3432 kN/m2 (25 to 35 gf/cm2), taps being fully opened and without a pan over the burner.)	-	100	NA
cl 18.1(the burner or burners are lighted by automatic ignition (battery of flint-operated) or by a pilot flame, it shall not be possible for gas to be admitted to the main burner without being smoothly ignited by the pilot flame. Each burner should be at room temperature at the beginning of the test and should be tested in turn)	-	50	NA
cl 18.1(There shall be easy and safe access for lighting and relighting each burner by a match stick and it shall be easy to see that the burner is lighted. Where)	-	50	NA
Cl17.2.2(When the gas consumption of a burner is reduced to simmer as described in 17.2, the flame shall not extinguish, blow off, strike back or form soot when tested with commercial LPG at 2942 kN/m2 (30 gf/cm2) gas inlet pressure.)	-	500	NA
Cl17.2.1(b) For burners above 60 I/h gas rate, 22 I/h or 26 percent of the rated capacity whichever is higher.)	-	500	NA
Cl17.2.1(It shall be possible to reduce the consumption rate of the burner to the following extent by providing a fixed simmer orifice in the gas tap: a) For burners up to 60 I/h gas rate, 35 percent of the rated capacity; and)	-	500	NA
Cl 17.1(Each burner assembly under separate ‘ON/OFF’ control shall give + 8 percent of the manufacturers’ specified gas consumption in I/h or heat input in kcaVh at 2942 kN/m2 (30 gf/cmz))	-	400	NA
Cl.15(When tested as specified in Annex C, the vertical resultant deflection of the top surface measured at the centre of length of the body, shall not exceed 2 mm and the distance between the opposite sides (lengthwise and widthwise) shall not change by more than 5 mm.)	-	300	NA
Cl 14.2(The position of the gas inlet shall allow connection to a gas supply on either side of the appliance. Inlet connection at the rear is also permitted. It shall be possible to change gas inlet from one side to other side easily by standard tools.)	-	100	NA
Cl 14.1(Cl 18.4 of IS 5116)(The external surface of the gas rail shall be treated to resist corrosion.)	-	100	NA
Cl 14.1(Cl 18.4 of IS 5116)(The pipe/tube used for main gas rail shall be of mild steel. The wall thickness of main gas rail shall be 1.6 mm + no Iimit/–0.15 mm.)	-	100	NA
Cl 14.1(Cl 18.3 of IS 5116)(Screwed gas inlet and outlet connections shall have threads specified in 17.3.)	-	100	NA
Cl 14.1(Cl 18.2 of IS 5116)(Where nozzles for flexible tubing are fitted, they shall be so positioned as to facilitate fitting of the tubing and also to prevent heating of the tubing to more than 60°C. Shape of nozzles is given in Fig. 7.)	-	100	NA
Cl 14.1(Cl 18 of IS 5116)(Nozzles shall be machined from free cutting brass or mild steel.)	-	100	NA
Cl 13.2 .1(The stove may be provided with a gas leak indicator. If gas leak indicator is provided, it shall conform to the requirements of IS 13432 (Part 1) or IS 13432 (Part 2).)	-	100	NA
Cl 13.1 (Cl 16 OF IS 5116)(All gas carrying parts of the appliance shall be sound and these parts when connected, to form a complete assembly shall also be soundagainst any gas leakage. The complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m2 (approx 150 gf/cm2). The details of test are given in Annex J.)	-	100	NA
Cl 12.1.1(Loose pan supports shall be so designed that it is not possible to place them firmly in other than proper position.)	-	100	NA
Cl 12.1(The design of the pan supports shall be such that it is practicable to support a pan of 100mm diameter, over at least one top burner without the use of loose rings, and such that 125 mm diameter vessel remains stable over each burner. Prongs of the support shall have suitable taper to accommodate round bottom pans.)	-	100	NA
Cl 11 .3(The stove comprising two or more burners shall include one burner having a rating of at least 1490 kcal/h, based on net calorific value of the gas ( when using commercial butane).)	-	100	NA
Cl 11.2(For burners having centre flame,provision shall be made to protect the centre flame from pans resting directly on burner top and smothering the centre flame.)	-	100	NA
Cl 11 (cl 10.5 of 1S 51 I6 )(If the burner is made and assembled in two or more parts they shall be so designed to provide proper self-locating arrangement so that they are always re-assembled to its original design preventing any maladjustment in their assembly. This shall also be applicable for primary air regulators.)	-	100	NA
Cl 11 (cl 10.3 of 1S 51 I6 )(The lightness of the joints in the burner assembly shall not depend upon adhesives or any kind ot packmg)	-	100	NA
Cl 11 (cl 10.4 of 1S 51 I6 )(If primary air regulators are used, they shall be so designed that they are not easily maladjusted by the user and the construction shall be such that primary air adjustment can be made with the burner in place ( see Fig. 6 ).)	-	100	NA
Cl 11 (cl 10.2 of 1S 51 I6 )(The burner supports shall be rigid and shall be fixed in their place. Their construction shall ensure the stability of the burners and shall prevent their undue movement in a horizontal plane.)	-	100	NA
Cl 11 (cl 10.1 of 1S 51 I6 )(The construction of the burners and the assembly shall allow their dismantling from the supports easily with or without the use of tools (see Fig. 5 for guidance).)	-	100	NA
Cl 10 (cl 9.2 of 1S 51 I6 )(The size of the Jet in litres per hour of flow of LPG at STP conditions shall be impressed upon it.)	-	100	NA
Cl 10 (cl 9.1.1 of 1S 51 I6 )(Injector Jet shall be made of metal, with or without ceramic tip. The melting point of the metal shall not be less than 650°C.)	-	100	NA
Cl 10 (cl 9.1 of 1S 51 I6 )(Threads 6 mm, Min)	-	100	NA
Cl 10 (cl 9.1 of 1S 51 I6 )(Projection from the face of mounting)	-	100	NA
Cl 10 (cl 9.1 of 1S 51 I6 )(The injector Jets shall be fixed calibrated type and it shall not be possible to loosen them without the use of tools. The dimensions of the injector Jet shall conform to the following requirements: Across flats 6 mm. nominal M 5 or 1BA)	-	100	NA
Cl 9 (Cl 8.11.2 of IS 5116 )(The niting means adopted shall be sufficiently robust to withstand normal use without distortion or damage.)	-	100	NA
Cl 9 (Cl 8.11.1 of IS 5116 )(Simmer flame shall be obtained by fixed simmer orifice.)	-	100	NA
Cl 9 (Cl 8.11 of IS 5116 )(Taps having an 'OFF' position shall have positive stops at the 'OFF' and simmer position except that special purpose taps (for appliance incorporating auto or self ignition device), for example, taps with simmering position in between 'OFF' and 'ON' may have a movement beyond the simmer position with a positive stop)	-	100	NA
Cl 9 (Cl 8.10 of IS 5116 )(Screw-down valves shall be so designed that it is impossible to withdraw completely the valve stem in the normal operation of the tap.)	-	100	NA
Cl 9 (Cl 8.9 of IS 5116 )(Screws, nuts, etc, which regulate the tension of taps valve or springs, shall not loosen in operation of the appliance. It shall not be possible to cause a leak during normal manual operation of tap.)	-	100	NA
Cl 9 (Cl 8.8 of IS 5116 )(All controls or taps shall be easy to operate at all temperatures normally attained in use.)	-	100	NA
Cl 9 (Cl 8.7 of IS 5116 )(Taper plug taps shall have dimensional allowances when in 'OFF' position given in Fig. 4.(C1 3.0 Min))	-	100	NA
Cl 9 (Cl 8.7 of IS 5116 )(Taper plug taps shall have dimensional allowances when in 'OFF' position given in Fig. 4.(B1 0.4 Min))	-	100	NA
Cl 9 (Cl 8.7 of IS 5116 )(Taper plug taps shall have dimensional allowances when in 'OFF' position given in Fig. 4.(A1 1.2 Min))	-	100	NA
Cl 9 (Cl 8.7 of IS 5116 )(Taper plug taps shall have dimensional allowances when in 'OFF' position given in Fig. 4.(D 2.80 Min))	-	100	NA
Cl 9 (Cl 8.7 of IS 5116 )(Taper plug taps shall have dimensional allowances when in 'OFF' position given in Fig. 4.(C 3.0 Min))	-	100	NA
Cl 9 (Cl 8.7 of IS 5116 )(Taper plug taps shall have dimensional allowances when in 'OFF' position given in Fig. 4.(B 0.4 Min))	-	100	NA
Cl 9 (Cl 8.7 of IS 5116 )(Taper plug taps shall have dimensional allowances when in 'OFF' position given in Fig. 4.(A 1.1 Min)	-	100	NA
Cl 9 (Cl 8.6 of IS 5116 )(Each taper plug tap shall be spring-loaded to maintain a gas-tight fit. Helical springs fitted in taps and valves shall have flattened ends, which shall be rounded before fitting.)	-	100	NA
Cl 9 (Cl 8.5 of IS 5116 )(Taps shall be so made that in normal use and with reasonable application of lubricant, the gas passages do not become blocked (see Fig. 3).)	-	100	NA
Cl 9 (Cl 8.4 of IS 5116 )(Preferably all taps (excluding pilot taps) should lock in the 'OFF' position but in all cases it shall be impossible for any handle or tap to move accidentally, for example, by the weight of plugs or handles or when caught by clothing. If this requirement is satisfied by means of an automatic locking device, the tap shall be easy to operate with one hand.)	-	100	NA
Cl 9 (Cl 8.3 of IS 5116 )(Where taps are fitted with adjustable stops, there shall be means for locking the stops in position. If screws are used for this purpose, they shall not lead into gas passages)	-	100	NA
Cl 9 (Cl 8.2 of IS 5116 )(The direction of rotation of a tap knob (handle) off-on-simmer shall be anticlockwise.)	-	100	NA
Cl 9 (Cl 8.2 of IS 5116 )(Taps shall be designed so that when placed in any position on &viewed from a distance of 3 m, will definately indicate whether the valve is open or close or in intermediate position.)	-	100	NA
Cl 9 (Cl 8.2 of IS 5116 )(All taps shall close in the same direction.)	-	100	NA
Cl 9 (Cl 8.2 of IS 5116 )(The ON,OFF and any fixed position of tap handles shall be clearely & durably indicated or shall be obvious by design or position. Where it is not obvious which tap operates which burner , some indication shall be give)	-	100	NA
Cl 9 (Cl 8.1 of IS 5116 )(The appliance shall have at least one tap for each burner.)	-	100	NA
Cl 8.3(Except for burners, all other parts, namely, springs, screws, bolts and nuts, pipes, pins, etc, which are visible can be removed for maintenance shall be of corrosion resistant material or treated to resist corrosion appropriate to the conditions of use.)	-	100	NA
Cl 8.2 of IS 4246(The external finished surfaces shall be easily cleanable.)	-	100	NA
Cl 8.1 ,(Cl 7.5 of IS 5116)(Concealed tubular fittings liable to corrode shall be protected by bituminous paint or other equally protective materia)	-	100	NA
Cl 8.1 ,(Cl 7.4.2 of IS 5116)(Resistance to Heating)	-	100	NA
Cl 8.1 ,(Cl 7.4.1 of IS 5116)(Resistance to Abrasion)	-	100	NA
Cl 8.1 ,(Cl 7.3.3 of IS 5116)(,Corrosion Resistance The plated article shall be subjected to the test for 12 h as covered in IS 6910 : 1985. The rating shall be assigned using the methods described in IS 6009 : 1970.)	-	100	NA
Cl 8.1 (Cl 7.3.2 of IS 5116)(Adhesion Test)	-	100	NA
Cl 8.1(The top flat surface of the body of the appliance, if plated, shallhave a coating of minimum of 10 microns of nickel followed by0.2 microns minimum of chromium.)	-	100	NA
Cl 7(Cl 7)	-	100	NA
Cl 6.6(Cl 6.6)	-	100	NA
Cl 6.5(Cl 6.5)	-	100	NA
Cl 6.4(Cl 6.4)	-	100	NA
Cl 6.3(Cl 6.3)	-	100	NA
Cl 6.2(The parts of burner shall not become disconnected during operation of appliance.the centers of adjoining burner shall not be less than 180 mm.)	-	100	NA
Cl 6 , DESIGN FOR MAINTENANCE(Cl 6.1)	-	100	NA
IS 5116 .(The number of glass fragments contained in a square of side 50mm located in the area of the largest pieces shall be at least 40 numbers. (Test Method as per Cl.15.2))	-	100	NA
4.1 of IS 5116(General)	-	200	-
4.2 of IS 5116(General)	-	200	-
4.1.1(General)	-	200	-
Cl 5 and 5 of IS 5116 .(IS 5116)	-	200	NA
Cl 5 and 5 of IS 5116 .(IS 5116)	-	250	NA
Cl 5 and 5 of IS 5116 .(IS 5116)	-	200	NA
Cl 5 and 5 of IS 5116 .(IS 5116)	-	200	NA
Cl 5 and 5 of IS 5116 .(All copper and copper alloy parts shall pass mercurous nitrate test .)	-	200	NA
Cl 5 and 5 of IS 5116 .(IS 5116)	-	200	NA
Cl 5 and 5 of IS 5116 .(IS 5116)	-	200	NA
Cl 5 and 5 of IS 5116 .(IS 5116)	-	200	NA
Cl 5 and IS 5116 .Surface of Glass Or Glass Ceramic(IS 5116)	-	200	NA
IS 5116 .(IS 5116)	-	200	NA
IS 5116 .(IS 5116)	-	200	NA
IS 5116 .(IS 5116)	-	200	NA
IS 5116 .(When a pan support for an uncovered burner is in contact withthe glass ceramic surface of the gas stove, the surface area ofthe pan support in contact with the glass ceramic surface shallbe at least 25 mm2.)	-	250	NA
IS 5116 .(Toughened glass shall fragment into small particles.)	-	200	NA
Cl18.4 (Cl14 of IS 5116)(Shall prevent gas from being supplied to the main burner until the pilot flame, if provided, is established;)	-	200	NA
Cl18.4 (Cl14 of IS 5116)(Shall, after flame failure, stop all gas flow to the main burner;)	-	200	NA
Cl18.4 (Cl14 of IS 5116)(Shall be actuated only by a pilot flame, if provided, to ignite the main burner without failure or delay;)	-	200	NA
Cl18.4 (Cl14 of IS 5116)(Shall open and close in times not exceeding the following limits:Opening from cold Closing from the fully heated condition Time Manually Non-manually Operated, Operated, seconds seconds 40 90 75 90)	-	500	NA
Cl18.4 (Cl14 of IS 5116)(Shall be free from any weakness in design which will give rise to failure to danger; and)	-	500	NA
25.1 ( 23.1 of IS 5116 )(Fire Hazard and Limiting Temperatures)	-	500	NA
25.1 ( 23.2 of IS 5116 )(Fire Hazard and Limiting Temperatures)	-	500	NA
25.1 ( 23.2.1 of IS 5116 )(Fire Hazard and Limiting Temperatures)	-	500	NA
25.2(Fire Hazard and Limiting Temperatures)	-	500	NA
26 (for burner 1)(Thermal Efficiency)	-	500	NA
26 (for burner 2)(Thermal Efficiency)	-	500	NA
26 (for burner 3)(Thermal Efficiency)	-	500	NA
26 (for burner 4)(Thermal Efficiency)	-	500	NA
26 (for burner 5)(Thermal Efficiency)	-	500	NA
5 (5.1.1 of IS 5116)(Materials)	-	100	NA
8.1 (7.1 of IS 5116)(Mechanical (Workmanship and Finish))	-	50	NA
17.1.2(Gas Consumption)	-	150	NA

Complete

05 Oct, 2022

-
-

IS 302 : Part 2 : Sec 30 (2007)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 30 room heaters (First Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6 (Classification)	-	100	NA
Cl.8 & IS:302-1:2008(Protection Against Access to Live Parts)	-	100	NA
Cl.10 & IS:302-1:2008(Power Input and Current)	-	300	NA
Cl.11 & IS:302-1:2008(Heating)	-	1000	NA
Cl.13 & IS:302-1:2008(Leakage Current & Electric Strength at operating temp. )	-	500	NA
Cl.14 & IS:302-1:2008(Transient Over Voltages)	-	500	NA
Cl.15 & IS: 302-1:2008(Moisture Resistance )	-	500	NA
Cl.17 & IS:302-1:2008(Over load Protection of Transformers and Associated Circuits )	-	500	NA
Cl.19 & IS:302-1:2008(Abnormal Operation.)	-	400	NA
Cl.20 & IS:302-1:2008(Stability & Mechanical Hazards)	-	300	NA
Cl.21 & IS:302-1:2008)(Mechanical Strength.)	-	300	NA
Cl.22.1 of IS 302-1:2008(Construction)	-	500	NA
Cl.24.1.3 (Component)	-	300	NA
Cl.25.1 of 302-1:2008(Supply Connection and External Flexible Cords )	-	700	NA
Cl.27.1 of 302-1:2008(Provision for Earthing.)	-	700	NA
Cl.28 of 302-1:2008(Screws and Connections.)	-	100	NA
Cl.29.1 of IS:302-1:2008(Clearances, Creepage Distances and Solid Insulation : Clearance )	-	200	NA
Cl.30.2.2 of 302-1:2008(Resistance to Heat and Fire)	-	1000	NA
Cl.31 & IS:302-1:2008(Resistance to Rusting.)	-	1000	NA

Complete

05 Oct, 2022

-
-

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	100	NA
7.0(Dimension and Tolerances)	-	200	NA
8.1 Table 1(Cu)	-	700	NA
8.1 Table 1(Pb)	-	700	NA
8.1 Table 1(Fe)	-	700	NA
8.1 Table 1(Total other impurities excluding iron)	-	500	NA
8.1 Table 1(Zn)	-	700	NA
9.1 Table-2(Tensile Strength)	-	700	NA
9.1 Table-2(Elongation)	-	700	NA
9.2(Vickers Hardness)	-	500	NA
10.1(Mercurous Nitrate Test)	-	500	NA

Complete

05 Oct, 2022

-
-

IS 302 : Part 2 : Sec 15 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 15 appliances for heating liquids (First Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Protection against live parts)	-	500	NA
10(POWER INPUT AND CURRENT)	-	700	NA
11(HEATING)	-	1500	NA
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	1200	NA
14(TRANSIENT OVERVOLTAGES)	-	1000	NA
15(MOISTURE RESISTANCE)	-	1500	NA
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	1300	NA
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	1500	NA
19(ABNORMAL OPERATION)	-	2000	NA
18(ENDURANCE)	-	1000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	1000	-
21(MECHANICAL STRENGTH)	-	1000	-
22(CONSTRUCTION)	-	1000	-
23(INTERNAL WIRING)	-	1000	-
24(COMPONENTS)	-	1000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	1000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1000	-
27(PROVISION FOR EARTHING)	-	1000	-
28(SCREWS AND CONNECTIONS)	-	100	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	100	-
30(RESISTANCE TO HEAT AND FIRE)	-	100	-
31(RESISTANCE TO RUSTING)	-	100	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	100	-

Complete

05 Oct, 2022

-
-

IS 368 (2014)

Electric immersion water heaters - Specification (Fifth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6 of IS 302-‐2-‐201:2008(Classification)	-	50	NA
Cl.8 of IS 302‐2-201: 2008(Protection Against Access to Live Parts)	-	100	NA
Cl.10 of IS 302‐2‐201:2008(Power Input and Current )	-	300	NA
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	NA
Cl. 12 of IS 368:2014(Operation under overload conditions of appliances with heating elements)	-	500	NA
Cl.13 of IS 302-2-201: 2008(Leakage Current & Electric Strength at Operating Temperature)	-	300	NA
Cl.14 of IS 302‐2-201:2008(Transient Over Voltages )	-	300	NA
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	700	NA
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	700	NA
Cl.17 of IS 302‐2-201: 2008(Overload Protection of Transformers & Associated Circuits)	-	500	NA
Cl.18 of IS 368:2014(Endurance)	-	500	NA
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	300	NA
Cl.20 of IS 302-2-201: 2008(Stability & Mechanical Hazards)	-	300	NA
Cl.22 of IS 302-2-201: 2008(Construction)	-	300	NA
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	300	NA
Cl.23 of 302-2-201:2008(Internal Wiring )	-	300	NA
Cl.24 of IS 302-2-201: 2008(Component)	-	300	NA
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	500	NA
Cl.26 of IS 302-2-201: 2008(Terminals for External Conductors)	-	500	NA
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	700	NA
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	700	NA
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	1000	NA
Cl.31 of IS 302-2-201:2008(Resistance of Rusting )	-	1000	NA
Cl.32 of IS 302-2-201:2008(Radiation, Toxicity and Similar Hazards)	-	500	NA
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	50	NA

Complete

05 Oct, 2022

-
-

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Air Pressure Test)	-	2000	NA
8.2(Proof Pressure Test)	-	1000	NA
8.3(Operating Test for Pressure Regulating Device)	-	1000	NA
8.4(Test for Safety Pressure Relief Device)	-	1400	NA
8.5(Bursting Pressure Test)	-	1000	NA
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	500	NA
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	500	NA
8.7(Test for Spring Loaded Mechanism)	-	500	NA
7.4(WORKMANSHIP AND FINISH)	-	500	NA
7.1(WORKMANSHIP AND FINISH)	-	600	NA
7.2(WORKMANSHIP AND FINISH)	-	500	NA
7.3(WORKMANSHIP AND FINISH)	-	500	NA
6.4.1(Handles and Knobs)	-	500	NA
6.4.1.1(Handles and Knobs)	-	500	NA
6.3.1(Temperature Responsive Pressure Relief Device)	-	500	NA
6.3.1(Temperature Responsive Pressure Relief Device)	-	500	NA
6.2(Safety Relief Device)	-	500	NA
6.2.1(Safety Relief Device)	-	500	NA
6.2.2(Safety Relief Device)	-	500	NA
6.1(Pressure Regulating Device)	-	500	NA
6.1.1(Pressure Regulating Device)	-	500	NA
6.1.2(Pressure Regulating Device)	-	500	NA
6.1.3(Pressure Regulating Device)	-	500	NA
6.1.4(Pressure Regulating Device)	-	500	NA
6.1.5(Pressure Regulating Device)	-	500	NA
6(CONSTRUCTION)	-	500	NA
5.9(Spring)	-	500	NA
5.8(Vent Pipe Nut)	-	500	NA
5.7(Vent Pipe)	-	500	NA
5.6(Vent Seal Pin for Pressure Regulating Device)	-	500	NA
5.5(Pressure Regulating Device)	-	500	NA
5.4(Handles and Knobs)	-	500	NA
5.3(Gasket)	-	2500	NA
5.2(Safety Relief Device)	-	2000	NA
5.1.1(Body, Lid, Containers and Grid)	-	500	NA
5.1.2(Body, Lid, Containers and Grid)	-	500	NA
5.1.3(Body, Lid, Containers and Grid)	-	500	NA
5.1.4(Body, Lid, Containers and Grid)	-	500	NA
4.1(Capacity)	-	500	NA
8.8(Test for Spring Loaded Mechanism)	-	15000	-
8.9(Test for Spring Loaded Mechanism)	-	10000	-
8.1(testing of handles of the cooker)	-	5000	-

Complete

05 Oct, 2022

-
-

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl.8 of IS 302-2-21:2011)(Protection Against Access to Live Parts)	-	4000	NA
(Cl.10 of IS 302-2-21: 2011)(Power Input & Current)	-	100	NA
(Cl.11 of 302-2-21:2011)(Heating)	-	500	NA
(Cl.13 of IS 302-2-21:2011)(Leakage Current )	-	500	NA
(Cl.13 of IS 302-2-21:2011)(Electrical Strength at Operating Temperature)	-	500	NA
(Cl.14ofIS302-2-21:2011)(Transient Over Voltages)	-	500	NA
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	1500	NA
(Cl.17 of IS 302-2-21:2011)(Overload protection of transformers & associated circuits)	-	1500	NA
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	500	NA
(Cl.20 of IS 302-2-21:2011)(Stability & Mechanical Hazards)	-	700	NA
(Cl.21ofIS302-2-21:2011)(Mechanical strength)	-	500	NA
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	400	NA
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	300	NA
(Cl.24ofIS302-221:2011)(Component)	-	500	NA
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	500	NA
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	400	NA
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	250	NA
(Cl.29ofIS302-2-21:2011)(Clearances, Creepage Distances and Solid Insulation)	-	1200	NA
Cl.8 of IS 302-2-21:2018(Protection Against Access to Live Parts)	-	300	-
Cl.10 of IS 302-2-21: 2018(Power Input & Current)	-	300	-
Cl.11 of 302-2-21:2018(Heating : Room Temp.)	-	200	-
Cl.13 of IS 302-2-21:2018(Leakage Current )	-	300	-
Cl.15 of IS 2082:2018(Verification of the Rated Capacity)	-	500	-
(Cl.17 of IS 2082:2018)(Hot Water Output)	-	200	-
Cl.19 of IS 302-2-21:2018(Abnormal Operation : leakage from container during test)	-	300	-
Cl.21.1 of IS 302-1:2008(Mechanical strength : Rough handling in normal use)	-	500	-
(Cl.22 of IS 2082:2018)(Finish)	-	200	-
Cl. 23 of IS 302-1:2008(Internal Wiring : color identification for earthing conductor )	-	500	-
Cl.24.102 of IS 302-221:2018(Component : Operation of thermal cut-out )	-	500	-
Cl.25.18 of IS 302-1:2008(Supply Connection & External Flexible Cords)	-	400	-
Cl.26 of IS 302-2-21: 2018(Terminals for External Conductors)	-	300	-
Cl.27 of IS 302-2-21:2018(Provision for Earthing)	-	200	-
Cl.29.1 of IS 302-1:2008(Clearances, Creepage Distances and Solid Insulation : Clearance distance )	-	100	-

Complete

05 Oct, 2022

-
-

IS 15558 (2005)

Mini domestic water heater for use with LPG - Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials)	-	200	NA
5.2(Materials)	-	100	NA
5.3(Materials)	-	100	NA
5.4(Materials)	-	100	NA
5.5(Materials)	-	100	NA
6.1(Connections)	-	100	NA
6.2(Connections)	-	100	NA
6.3(Connections)	-	100	NA
6.4(Connections)	-	100	NA
6.5(Connections)	-	100	NA
6.6(Gas Inlet Connections)	-	100	NA
6.6(Gas Inlet Connections)	-	100	NA
6.6(Gas Inlet Connections)	-	100	NA
6.6(Gas Inlet Connections)	-	100	NA
6.6(Gas Inlet Connections)	-	100	NA
7(Flame Visibility)	-	100	NA
8(Gas Taps)	-	200	NA
9(Flame Failure Device)	-	200	NA
10(Ignition Device)	-	100	NA
11(Protection Against Accidental Overheating)	-	500	NA
12(Water Rate Adjuster)	-	500	NA
14(Gas Soundness)	-	200	NA
15(Water Soundness)	-	300	NA
16(Thermal Efficiency)	-	1500	NA
17(Combustion)	-	500	NA
18(Gas Consumption)	-	2000	NA
19.1(Ignition and flame travel)	-	200	NA
19.2(Ignition and flame travel)	-	100	NA
19.3(Ignition and flame travel)	-	100	NA
20(Flame Stability)	-	200	NA
21(Noise Control)	-	200	NA
22(Flash Back)	-	300	NA
23(Resistance to Draught)	-	300	NA
24(Fire Hazard And Limiting Temperature )	-	400	NA
25(Time For Temperature Rise)	-	500	NA

Complete

05 Oct, 2022

-
-

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Classification Heavy/Medium/L:ight)	-	100	NA
4(Material)	-	100	NA
0.5(Fabrication)	-	100	NA
5.1(The utensil shall be pressed or spun from one piece)	-	100	NA
5.2( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-	100	NA
5.2(Lid Thickness of the finished utensil, mm)	-	100	NA
6.1 & Table 1( i) Name of Utensil )	-	100	NA
6.1 & Table 1(ii) Shape of Utensil)	-	100	NA
6.1 & Table 1( Nominal Size, mm)	-	100	NA
6.1 & Table 1(Inside dia, Φ D mm Not declared )	-	200	NA
6.1 & Table 1(Outside dia Ф NA)	-	200	NA
6.1 & Table 1(Height NA)	-	200	NA
6.1 & Table 1(Capacity, l NA)	-	200	NA
6.1( Minimum sheet thickness for nominal size )	-	200	NA
7.1(HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-	500	NA
7.2(Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-	500	NA
8.1(The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-	500	NA
8.2(The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-	500	NA
8.4.1.2( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-	500	NA
8.4.2(A coating of thickness 25 to 100 microns is generally required)	-	500	NA
8.4.3(Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-	1500	NA
8.4.4(The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-	500	NA
8.4.4(The film will appear dark grey when wet. )	-	500	NA
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-	500	NA
9(The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-	500	NA
10(Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-	500	NA

Complete

05 Oct, 2022

-
-

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	399.97	NA
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
8.2, Table 3(Tensile Test-1608:Part 1)	-	500	NA
8.2, Table 3(Proof Stress, N/mm2)	-	400	NA
8.2, Table 3(Tensile Strength, N/mm2)	-	500	NA
8.2, Table 3(Elongation, %)	-	500	NA
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	300	NA
8.4(Bend Test)	-	200	NA
8.5(Erichsen Cupping Test)	-	200	NA
10.1(Thickness, mm)	-	100	NA
10.2(width, mm)	-	100	NA
10.3(Length, mm)	-	100	NA
10.4(Flatness,mm)	-	100	NA
10.5(Camber, mm)	-	100	NA
11(Surface Finish)	-	100	NA

Complete

05 Oct, 2022

-
-

IS 446 (2017)

Rubber hoses, textile - Reinforced, for compressed air - Specification (Fifth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Classification)	-	250	NA
Cl 5(Materials and construction)	-	500	NA
Cl 6.1 & Table 1(Internal diameters and tolerances)	-	250	NA
Cl 6.2(Concentricity)	-	250	NA
Cl 6.3(Tolerance on length)	-	250	NA
Cl 6.4(Minimum thickness of lining and cover-Type 1 )	-	100	NA
Cl 6.4(Minimum thickness of lining and cover-Type 1 )	-	100	NA
Cl 6.4(Minimum thickness of lining and cover-Type 2 )	-	100	NA
Cl 6.4(Minimum thickness of lining and cover-Type 2 )	-	100	NA
Cl 6.4(Minimum thickness of lining and cover-Type 3)	-	100	NA
Cl 6.4(Minimum thickness of lining and cover-Type 3)	-	100	NA
Cl 7.1 & Table 2(Minimum tensile strength)	-	100	NA
Cl 7.1 & Table 2(Minimum tensile strength)	-	1000	NA
7.1, Table 2(Elongation at Break of Lining of all types)	-	1000	NA
7.1, Table 2(Elongation at Break of Cover of all types)	-	500	NA
Cl 7.1 & Table 2(Resistance to ageing-Change in tensile strength from original value (max.) )	-	500	NA
7.1, Table 2(Accelerated Ageing for all types: Change in Tensile Strength of Cover of its original value)	-	500	NA
Cl 7.1 & Table 2(Resistance to ageing-Change in elongation at break from original value (max.) original value (max.) )	-	500	NA
7.1, Table 2(Accelerated Ageing for all types: Change in Elongation of Cover of its original value)	-	500	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (class A))	-	500	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (class A))	-	500	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (max.) (class B only) )	-	500	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (max.) (class B only) )	-	500	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (max.) (class C only) )	-	500	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (max.) (class C only) )	-	500	NA
7.2, Table 3(Proof Pressure at 23°C for type 1)	-	500	NA
7.2, Table 3(Proof Pressure at 23°C for type 2)	-	300	NA
7.2, Table 3(Proof Pressure at 23°C for type 3)	-	300	NA
7.2, Table 3(Change in Length at Maximum working Pressure)	-	300	NA
7.2, Table 3(Change in Diameeter at Maximum working Pressure)	-	300	NA
7.2, Table 3(Minimum Bursting Pressure for type 1)	-	300	NA
7.2, Table 3(Minimum Bursting Pressure for type 2)	-	300	NA
7.2, Table 3(Minimum Bursting Pressure for type 3)	-	300	NA
7.2, Table 3(Adhesion between Components- Lining and Reinforcement)	-	300	NA
7.2, Table 3(Adhesion between Components- Reinforcement layers)	-	300	NA
7.2, Table 3(Adhesion between Components- Cover and Reinforcement)	-	300	NA
7.2, Table 3(Ozone Resistance)	-	400	NA
7.2, Table 3(Flexibility at 23°C)	-	400	NA
7.2, Table 3(Low temperature Flexibility)	-	1000	NA

Complete

05 Oct, 2022

-
-

IS 2396 (2017)

Rubber hoses and hose assemblies for measured fuel dispensing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

05 Oct, 2022

-
-

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
Cl. 7.1 & 7.2 Table 1(Others-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	NA
Cl. 7.1 & 7.2 Table 1(Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl.12(Corrosion Resistance- IS 10461(Part1))	-	1000	NA
Cl.12(Corrosion Resistance- IS 10461(Part2))	-	1000	NA
6(Freedom from defects , IS 6911)	-	100	NA
10.1,Table 4&Table 6(Tensile Test - IS 1608(Pt -1))	-	1000	NA
10.2,Table 4&Table 5(Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-	1000	NA
10.3(Bend Test - IS 1599)	-	500	NA
11,Table 7(Erichsen cupping test-IS 10175)	-	500	NA
15(Surface Finish)	-	100	NA
17(Dimension and tolerance)	-	200	NA

Complete

05 Oct, 2022

-
-

IS 17153 (2019)

Domestic gas stoves for use with piped natural gas (PNG) - Specification

43000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(The construction of all the parts of equipment shall be sound and of high standard of workmanship and appropriate finish. The construction shall ensure durability and shall comply with the safety requirements.)	-	100	-
4.2(Rivets, Fastening screws and plugs , etc. shall not lead into gas passages.)	-	100	-
4.3(No pressure regulator shall be included as part of the stove.)	-	100	-
5.1(The appliance shall be free from swarf, grit and other foreign matters.)	-	100	-
5.1(If flexible tubing is used, it shall not be fitted on the outlet side of any control which is capable of cutting of the gas completely, except where screwed metal connection are fitted.)	-	100	-
5.1(The use of low pressure rubber or plastic tubing fitted or pushed on nozzle is not recommended.)	-	100	-
5.1.1(Plastic components which are liable to heating (For example, tap handles push buttons etc.) shall be free of fissures, distortion, blemishes and discolouration)	-	100	-
5.2(The burner parts shall not melt or distort when burner is operated with flames flashed back for half an hour in the mixing tube.)	-	100	-
5.3(Mercurous Nitrate test for copper and copper alloy Parts)	-	100	-
5.4(Change in weight or volume of a non metallic material, when immerse in n-Pentane or PNG for 72 hours)	-	200	-
5.5(The main body of the burner including mixer head, mixing tube and burner head shall be of substantial and durable construction)	-	100	-
5.6(Meltiing poin of metal used in oven, griller or auxilliary or anyother combination)	-	100	-
5.7(Drip tray if provided shall be made of non-corrosive material)	-	100	-
5.8.1(Toughened glass top including their edges or corners shall not have fissures or scratches)	-	200	-
5.8.2(The means to hold the glass top of the gas stove shall not allow any stress or risk of mechanical change to the glass top.)	-	200	-
5.8.2(The toughened glass top shall ensure durability against damage in normal use)	-	200	-
5.8.2(Pan support for an uncovered burner in contact with the glass ceramic surface.The surface area of the pan support in contact with the glass ceramic)	-	200	-
5.8.3(Toughened glass shall fragment into small particles.)	-	200	-
5.8.3(The number of glass fragments contained in a 50 mm side square, when tested as Cl. 15.2)	-	200	-
6.1(The appliance, including all the component parts, shall be easy to clean and maintain in good working order, there shall be easy access to the accessories and controls for maintenance and adjustment.)	-	100	-
6.2(the parts of the burner shall not become disconnected during operation of the appliance.)	-	100	-
6.2(The relative distance between the centres of the adjoining burner-)	-	100	-
6.3(Burner ports shall be so designed and located that in normal use spilage of food shall not cause internal fouling of mixing tube and or blockage of injector jet.)	-	100	-
6.4(Burners and parts of Burner only of same rating , model and make shall be interchangeable or replaceable without effecting performance.)	-	100	-
6.5(Parts, which are intented to be removable by the user, shall be easy to replace correctly and difficult to assemble incorrectly.)	-	100	-
6.6(All nuts, bolts and fittings having spanner flats shall be capable of being moved by suitable spanner or be readily accessible to an adjustable spanner.)	-	100	-
6.7(Thickness of Sheet)	-	100	-
7(Rigidity and Stability : The appliance shall be so designed that it remains stable and shall not be easily overturned.)	-	300	-
8.1(The Finish of exposed parts shall be durable, easy to clean and not subject to excessive deterioration in normal use.)	-	100	-
8.1(Parts, which will come in contact with the foodstuff, shall be capable of being hygienically cleaned.)	-	100	-
8.1(The finishes shall, on visual examination, show no defects, such as pin-holes, blisters, roughness or exposed area of metal, which give rise to undualy rapid deterioration in use.)	-	100	-
8.2(Vitreous enameled component shall meet the requirement when tested in accordance with Annex E of IS:5116)	-	100	-
8.3(Thickness of Nickel coating of the top flat surface of the body of electroplated stove.)	-	500	-
8.3.1(Thickness of Chromium coating)	-	500	-
8.3.2(Adhesion Test)	-	100	-
8.3.3(Corrosion Resistance test)	-	2000	-
8.4 (a)(Resistance to Abrasion)	-	200	-
8.4 (b)(Resistance to Heating)	-	200	-
8.5(Concealed Gas Supplies: Concealed tubular fittings liable to corrode shall be protected by bituminous paint or other equally protective material.)	-	100	-
8.6(All springs, screws, nuts and bolts which are visible or to be removed for maintenance, shall be of corrosion-resistant material or treated to resist corrosion.)	-	100	-
8.7(The external Finished surfaces shall be easily cleanable.)	-	100	-
9.1(The Appliance shall have at least one tap for each burner)	-	100	-
9.2(The 'ON' "OFF" and any fixed position of tap handles shall be clearly and durably indicated or shall be obvious by design or position else some indication shall be provided.)	-	100	-
9.2(All Taps shall close in the same direction. The direction of rotation of knob from off-on-simmer shall be anti-clockwise.)	-	100	-
9.2(Taps shall be designed so that when placed in any position and viewed from a distance of 3 m, will definitely indicate whether the valve is open, closed or in intermediate position.)	-	100	-
9.3(When Taps are fitted with adjustable stops, there shall be means of looking the stops in position. If screws are used for this purpose, they shall not lead into gas passages.)	-	100	-
9.4(Preferably all taps (Excluding pilot taps) should lock in the off position, but in all cases it shall be impossible to handle or tap to move accidentally…. )	-	100	-
9.5(Taps shall be so made that in normal use and reasonable application of lubricant, the gas passages do not become blocked.)	-	100	-
9.5.1(Taps shall be lubricated with suitable grease, resistant to the action of the gas and capable of operating at the maximum temperature of 110°C.)	-	100	-
9.6(Each taper plug tap shall be spring loaded to maintain a gas tight fit. Helical springs fitted in taps and valves shall have flattened ends, which shall be rounded before fitting.)	-	100	-
9.7(Dimension of Taper plugs in off position:)	-	700	-
9.7(A)	-	100	-
9.7(B)	-	100	-
9.7(C)	-	100	-
9.7(D)	-	100	-
9.7(A1)	-	100	-
9.7(B1)	-	100	-
9.7(C1)	-	100	-
9.8(All controls or taps shall be easy to operate at all temperatures normally attained in use)	-	100	-
9.9(Screws nuts etc., which regulate the tension of taps valve or springs shall not loosen in operation of the appliance. It shall not be possible to cause a leak during normal manual operation of tap.)	-	100	-
9.1(Screw-down valves shall be so designed that it is impossible to withdraw completely the valve stem in the normal operation of the tap.)	-	100	-
9.11(Taps having an 'OFF' position shall have positive stops at the 'OFF' and simmer position except that special purpose taps (for appliance incorporating auto or self ignition device))	-	100	-
9.11.1(Simmer flame shall be obtained by fixed simmer orifice.)	-	100	-
9.12(The noting means adopted shall be sufficiently robust to withstand normal use without distortion or damage.)	-	100	-
10.1(The Injector Jets shall be fixed calibrated type and it shall not be possible to loosen them without the use of tools.)	-	100	-
10.1(Dimension- Across Flats)	-	100	-
10.1(Dimension- Projection from the face of mounting, Nominal)	-	100	-
10.1(Dimension- Threads)	-	100	-
10.1.1(Injector Jet shall be made of metal , with or without ceramic tip. The melting point of the metal shall not be less than 650°C)	-	100	-
10.2(The Size of the jet in Litres per hour of flow of PNG at STP conditions shall be impressed upon it.)	-	100	-
11.1(The construction of the burners and the assembly shall allow their dismantling from the supports easily with or without the use of tools)	-	100	-
11.2(The Burner supports shall be rigid and shall be fixed in their place. Their construction shall ensure the stability of the burners and shall prevent their undue movement in a horizontal plane.)	-	100	-
11.3(The tightness of the joints in the burner assembly shall not be depended upon adhesives or any kind of packing.)	-	100	-
11.4(If primary air regulators are used, they shall be so designed that they are not easily maladjusted by the user and the construction shall be such that primary air adjustment can be made with the burner in place.)	-	100	-
11.5(If the burner is made and assembled in two or more parts they shall be so designed to provide proper self locating arrangement so that they are always reassembled to its original design preventing any maladjustment in their assembly. This shall also be applicable for primary air regulators.)	-	100	-
11.6(For Burners having centre flame, provision shall be made to protect the centre flame from pan resting directly on burner top and smothering the centre flame. )	-	100	-
11.7(The appliance comprising two or more burners shall include one burner having a rating of at least 1450 kCal/hr, based on net calorific value of the gas (When using domestic PNG))	-	100	-
12.1(The design of the pan supports shall be such that it is practicable to support a pan of 100 mm diameter over at least one top burner without the use of loose rings and such that 125 mm diameter vessel remains stable over each burner. )	-	100	-
12.1(Prongs of the Support shall have suitable taper to accommodate round bottom pans.)	-	100	-
12.1.1(Loose Pan support shall be so designed that it is not possible to place them firmly in other than proper position)	-	100	-
12.1.2(The material of the pan support shall be metallic.)	-	100	-
13(All gas carrying parts of the appliances should be sound and these parts when connected to form complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m²)	-	200	-
14.1(Nozzle shall be machined from free cutting brass, MS, SS, Zinc)	-	200	-
14.2(Where Nozzles for flexible tubing are fitted, they shall be so positioned as to facilitate fitting of the tubing and also to prevent heating of the tubing to more than 60°C)	-	200	-
14.2(Shape of Nozzles as per fig. 3 : (a))	-	100	-
14.2((b))	-	100	-
14.2(( c))	-	100	-
14.2((d))	-	100	-
14.2((e))	-	100	-
14.3(Screwed gas Inlet and outlet connections shall confirm to IS:554, Declared by party)	-	100	-
14.4(The wall thickness of main gas rail)	-	100	-
14.4(The pipe/tube used for main gas rail shall be of mild steel)	-	100	-
14.4(The external surface of the gas rail shall be treated to resist corrosion)	-	100	-
14.4(Any other connection made from the main gas rail shall be only metallic.)	-	100	-
14.5(The position of the gas inlet shall allow connection to a gas supply on either side of the appliances, the rear end or bottom is also permitted. It shall be possible to change gas inlet from one side to other side easily by standard tools.)	-	100	-
15(Vertical Deflection)	-	150	-
15(Length wise deflection)	-	150	-
15(Width wise deflection)	-	200	-
15.1(Verification of the strength of the gas stove surface of the toughened glass top against thermal stress)	-	100	-
15.2(Fragmentation test of the toughened glass to )	-	1000	-
17.1(Rating Declared)	-	10500	-
17.1( Burner-1)	-	1500	-
17.1( Burner-2)	-	1500	-
17.1( Burner-3)	-	1500	-
17.1(Burner-4)	-	1500	-
17.1(Burner-5)	-	1500	-
17.1.2(Total Gas Consumption)	-	3000	-
17.2(Sim Rating Declared)	-	7500	-
17.2(Burner-1)	-	1500	-
17.2(Burner-2)	-	1500	-
17.2(Burner-3)	-	1500	-
17.2(Burner-4)	-	1500	-
17.2(Burner-5)	-	1500	-
17.3(When the gas consumption of the burner is reduced to simmer, the flame shall not extinguish, blow off, strike back or form soot, when tested with commercial PNG at 21 mbar gas inlet pressure.)	-	100	-
18.1(There shall be easy and safe access of lighting each burner by matchstick and it shall be easy to see that the burner is lighted)	-	100	-
18.1(Where the burner or burners are lighted by automatic ignition (Battery of flint operated or by a pilot flame , it shall not be possible for gas to be admitted to the main burner without being smoothly ignited by the pilot flame. Each burner should be at room temperature at the begining of the test and should be tested in turn. )	-	100	-
18.2(if the flame is applied to any of the outer row of the burner ports when the gas is flowing , flame travel shall be complete……..)	-	100	-
18.3(When the burner is ignited from a pilot flame and/or by an electric/electronic method, the ignition and flame travel shall be smooth at pressure……..)	-	100	-
18.4.1(The flame failure device if provided shall confirm to IS:5116)	-	100	-
19.1(It shall be possible to operate stove with taps fully open at gas inlet pressure , without the flame extinguishing, blowing off or striking back and without the formation of soot.)	-	100	-
19.1.1(When the gas consumption of the burner is reduced to simmer after operating half an hour on full ON flame shall not extinguish, blow off, strike back or form soot at 21 mbar gas inlet pressure.)	-	100	-
19.2(Pilot Flame shall be Stable without lifting or soot deposition at gas inlet pressure from 20-25 gf/cm2)	-	100	-
19.3(Fixed Min Pilot flame shall be sufficient to relight the main burner at the 21 mbar gas inlet pressure.)	-	100	-
20(Ignition of Burner flame, their operation and turning off shall not give rise to undue excessive noise during the operation.)	-	300	-
21(When operated at pressure 20-25 gf/cm2 for half an hour flame shall be reduced to simmer and then brought back to full on, operation shall be repeated five times, no flash back shall occur during the test.)	-	300	-
22(When operated at pressure 20-25 gf/cm2 , for one at full on position, no soot shall be deposited on burner or on the bottom of the vessel.)	-	300	-
23(When operated at pressure 20-25 gf/cm2 , there shall be no extinction of flame on any of the burneroperating at the max of the burner, when the appliance is placed in normal current of air with velocity of 2 m/s.)	-	300	-
24(Burner-1)	-	2000	-
24(Burner-2)	-	2000	-
24(Burner-3)	-	2000	-
24(Burner-4)	-	2000	-
24(Burner-5)	-	2000	-
25.1(Rise of Temperature above room temperature in (Wall, Floor, Ceiling), after two hours of operation)	-	500	-
25.1(Temperature of the portion of the surface other than the working surface likely to be touched accidentally.)	-	500	-
25.1(Temperature of the surface in normal use)	-	500	-
25.1(Temperature of synthetic rubber diaphragm in gas carrying components)	-	500	-
25.2(With the Burner lighted on full on, the flame temperature at a height of H+20 mm)	-	500	-
26(Burner-1)	-	2500	-
26(Burner-2)	-	2500	-
26(Burner-3)	-	2500	-
26(Burner-4)	-	2500	-
26(Burner-5)	-	2500	-

Complete

05 Oct, 2022

-
-

IS 740 (1977)

Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (Second Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1of IS:740 (Designation 19000)(Copper)	-	625	-
4.1, Table 1of IS:740 (Designation 24345)(Copper)	-	550	-
4.1, Table 1of IS:740 (Designation 53000)(Copper)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Copper)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Copper)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Copper)	-	500	-
4.1, Table 1of IS:740 (Designation 19000)(Magnesium)	-	625	-
4.1, Table 1of IS:740 (Designation 19000)(Silicon)	-	625	-
4.1, Table 1of IS:740 (Designation 19000)(Iron)	-	625	-
4.1, Table 1of IS:740 (Designation 19000)(Manganese)	-	625	-
4.1, Table 1of IS:740 (Designation 19000)(Zinc)	-	625	-
4.1, Table 1of IS:740 (Designation 19000)(Aluminium)	-	625	-
4.1, Table 1of IS:740 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	625	-
4.1, Table 1of IS:740 (Designation 24345)(Magnesium)	-	550	-
4.1, Table 1of IS:740 (Designation 24345)(Silicon)	-	550	-
4.1, Table 1of IS:740 (Designation 24345)(Iron)	-	550	-
4.1, Table 1of IS:740 (Designation 24345)(Manganese)	-	550	-
4.1, Table 1of IS:740 (Designation 24345)(Zinc)	-	550	-
4.1, Table 1of IS:740 (Designation 24345)(Titanium and or other grain refining elements)	-	550	-
4.1, Table 1of IS:740 (Designation 24345)(Chromium)	-	550	-
4.1, Table 1of IS:740 (Designation 24345)(Aluminium)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Magnesium)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Silicon)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Iron)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Manganese)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Zinc)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Titanium and or other grain refining elements)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Chromium)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Cr+Mn)	-	500	-
4.1, Table 1of IS:740 (Designation 53000)(Aluminium)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Magnesium)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Silicon)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Iron)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Manganese)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Zinc)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Titanium and or other grain refining elements)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Chromium)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Cr+Mn)	-	500	-
4.1, Table 1of IS:740 (Designation 55000)(Aluminium)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Magnesium)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Silicon)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Iron)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Manganese)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Zinc)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Titanium and or other grain refining elements)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Chromium)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Cr+Mn)	-	500	-
4.1, Table 1of IS:740 (Designation 64430)(Aluminium)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Magnesium)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Silicon)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Iron)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Manganese)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Zinc)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Titanium and or other grain refining elements)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Chromium)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Either Cr or Mn shall present)	-	500	-
4.1, Table 1of IS:740 (Designation 65032)(Aluminium)	-	500	-
4.1, Table 1of IS:740 (Designation & Condition 19000, '112')(Tensile Strength of Size upto and including 12 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 24345, 'W')(Tensile Strength of Size upto and including 12 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 64430, 'W')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 65032, 'W')(Tensile Strength of Size upto and including 25 mm)	-	1000	-

Complete

05 Oct, 2022

-
-

IS 447 (1988)

Specification for rubber hose for welding (Fourth Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.2 - Table 1(Dimensions and Tolerances)	-	100	NA
Cl. 3.2 - Table 1(Dimensions and Tolerances)	-	100	NA
Cl. 3.2 - Table 1(Dimensions and Tolerances)	-	100	NA
Cl. 3.2 - Table 1(Dimensions and Tolerances)	-	100	NA
Cl. 3.3 - Table 2(Physical Requirements)	-	500	NA
Cl. 3.3 - Table 2(Physical Requirements)	-	500	NA
Cl. 3.3 - Table 2(Physical Requirements)	-	500	NA
Cl. 3.3 - Table 2(Physical Requirements)	-	500	NA
Cl. 3.3 - Table 2(Physical Requirements)	-	500	NA
Cl. 3.3 - Table 2(Physical Requirements)	-	500	NA
Cl. 3.3 - Table 2(Physical Requirements)	-	500	NA
Cl. 3.4 - Table3(Performance Requirements)	-	1000	NA
Cl. 3.4 - Table3(Performance Requirements)	-	1000	NA

Complete

05 Oct, 2022

-
-

IS 12585 (1988)

Specification for thermoplastic hoses (Textile Reinforced) for water - General purpose

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Types)	-	2000	NA
Cl 4.1(Construction)	-	2000	NA
Cl 4.2(Dimensions & Tolerances)	-	2000	NA
Cl 4.3.1 & Appendix A(Loss in Mass on Heating)	-	2000	NA
Cl 4.3.2(Adhesion)	-	500	NA
Cl 4.3.3(Pressure Requirements)	-	500	NA
Cl 4.3.4(Minimum Bend Radius)	-	1000	NA
Cl 4.3.5(Low Temperature Flexibility)	-	2000	NA

Complete

05 Oct, 2022

-
-

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1 (The tubing made out of this material shall be green in colour )	-	100	NA
Cl.4.2(The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-	100	NA
Cl4.3.1(The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-	200	NA
Cl4.3.2(it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-	200	NA
Cl.4.4,(Cl.4.4.1)(when tested in accordance with the method given in AnnexureA. It shall fit over the standard and oversize metal nozzle shown in Fig1,2 and 3)	-	200	NA
Cl.4.4,(Cl.4.4.2)(it shall remain atatched to both nozzles throught the test period)	-	200	NA
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the increase in the outside diametre of the tubing ,Also the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	1200	NA
Cl.4.6(Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-	1500	NA
Cl.4.7(Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-	1500	NA
Cl.4.8.1(Flexible test , Annexure B The gas pressure shown on the manometre shall not drop by more than 1 Kpa)	-	500	NA
Cl4.8.2(The tubing shall be so flexible that it will make contact with a cylinder former of radius 68 mm for at least 110 deg of its circumference when the tubing is placed over the framer and a mass of 1.6 kg is attcahed to each end)	-	800	NA
Cl.4.9(Crushing test , )	-	1000	NA
Cl.4.10(Resistance to lpg ,Annexure c Shall not be more than 15 % of the initial mass of the tubing and the amount of exctractable matter shall not excced 10 percent of the iniital mass of te tubing)	-	1500	NA
Cl.4.11(Resistance to Ozone ,Annexure D Shall not show any breakage on surface or crack or defects)	-	2000	NA
Cl.4.12(Burning behaviour on exposure to small flame,Annexure E tubing shall not burn to either of the outer marks within the test period of 45 seconds)	-	500	NA

Complete

05 Oct, 2022

-
-

IS 21 (1992)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2, Table 1of IS:21 (Designation 19000)(Copper)	-	400	NA
4.2, Table 1of IS:21 (Designation 19000)(Magnesium)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Manganese)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Zinc)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Aluminium)	-	200	-
4.2, Table 1of IS:21 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	200	-
4.2, Table 1of IS:21 (Designation 19000)(Lead)	-	200	-
4.2, Table 1of IS:21 (Designation 19500)(Copper)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Manganese)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Zinc)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Lead)	-	200	-
4.2, Table 1of IS:21 (Designation 19500)(Cu+Si+Fe+Mn+Zn)	-	200	-
4.2, Table 1of IS:21 (Designation 19500)(Aluminium)	-	600	-
4.2, Table 1of IS:21 (Designation 19600)(Copper)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Manganese)	-	500	-
4.2, Table 1of IS:21 (Designation 19600)(Zinc)	-	500	-
4.2, Table 1of IS:21 (Designation 19600)(Lead)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Cu+Si+Fe+Mn+Zn)	-	200	-
4.2, Table 1of IS:21 (Designation 19600)(Aluminium)	-	200	-
4.2, Table 1of IS:21 (Designation 31000)(Copper)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Magnesium)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Manganese)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Zinc)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Titanium and or other grain refining elements)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Chromium)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Lead)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Aluminium)	-	400	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Tensile Strength)	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Bend Test (Radius of Bend))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Tensile Strength)	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Bend Test (Radius of Bend))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(0.2 Percent Proof Stress)	-	500	-

Complete

05 Oct, 2022

-
-

IS 1746 (1992)

Shoe polish, paste - Specification (Third Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Odour)	-	500	NA
4.1.2(Colour)	-	100	NA
4.1.3(Consistency)	-	100	NA
4.1.4(Applicability)	-	100	NA
4.1.5(Amenability)	-	100	NA
4.1.6(colour of water extract)	-	200	NA
4.2 (table 1 S.no(i))(Softeing point of non-volatile matter)	-	3000	NA
4.2 (table 1 S.no(ii))(Ash of the non-volatile matter)	-	2000	NA
4.2 (table 1 S.no(iii))(pH of water extract )	-	500	NA
4.2 (table 1 S.no(iv))(Distillation range of volatile portion )	-	3000	NA
4.2 (table 1 S.no(v))(Flash point of volatile portion,)	-	2400	NA
4.2 (table 1 S.no(vi))(Non-volatile matter )	-	1000	NA

Complete

05 Oct, 2022

-
-

Bureau of Indian Standards

The National Standards Body of India

Shri Krishna Test House

B-70/1, Gali no 8 , New modern Shahdara ,Near DDA Flats mansarover park shahdara, Delhi, Shahdara, Delhi, 110032

9891112786 [email protected]

Scope List

No Record Found