BIS - LIMS (Laboratory Information Management System)

MSME Testing Centre, New Delhi

Shaheed Capt. Gaur Marg, Okhla Phase -III, New Delhi, South East, Delhi, 110020

9582093108 [email protected]

Scope List

Reset

68 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 12744 : Part 1 (2013)

Ready mixed paint, air drying, red oxide - Zinc phosphate, priming - Specification: Part 1 for domestic and decorative applications (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.2(Lead Restriction)	-	1000	-
Cl.5.3, 8.1 - Table 1 -i)(Drying time hard dry)	-	500	-
Cl.5.3, 8.1 - Table 1 -ii)(Consistency )	-	500	-
Cl.5.3, 8.1 - Table 1 -iii)(Finish)	-	500	-
Cl.5.3, 8.1 - Table 1 -iv)(Colour in Natural Daylight)	-	500	-
Cl.5.3, 8.1 - Table 1 -v)(Wet Opacity)	-	500	-
Cl.5.3, 8.1 - Table 1 -vi)(Pigment Content)	-	500	-
Cl.5.3, 8.1 - Table 1 -vii)(Zinc Phosphate)	-	500	-
Cl.5.3, 8.1 - Table 1 -viii)(Red Oxide (as Fe2O3) )	-	500	-
Cl.5.3, 8.1 - Table 1 -ix) a)(Flexibility and adhesion a) Scratch Hardness (Load 800 g))	-	500	-
Cl.5.3, 8.1 - Table 1 -ix) b)(Flexibility and adhesion b) Bent Test (with 6.25 mm dia mendrel in type 1 apparatus)	-	500	-
Cl.5.3, 8.1 - Table 1 -x) a)(Resistance to humidity under conditions of condensation a) Resistance to humidity (for 7 days))	-	2000	-
Cl.5.3, 8.1 - Table 1 -x) b)(Resistance to humidity under conditions of condensation a) Resistance to Salt Spray (for 96 Hours))	-	2000	-
Cl.5.3, 8.1 - Table 1 -xi)(Flash Point)	-	500	-
Cl.5.3, 8.1 - Table 1 -xii)(Mass)	-	500	-
Cl.5.3, 8.1 - Table 1 -xiii)(Keeping Properties)	-	10000	-

Complete

-
-

IS 7532 (2018)

Soft soap - Specification (First RevisIon)

11950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CL 5 ( 5.1)(The material shall be homogeneous translucent mass of jelly-like texture, free from putrescent, fishy or objectionable odour. It applies to soft soap with potassium or sodium base or a mixture of these bases. It does not apply to soaps for medicinal purposes. It may or may not be suitably perfumed subject to agreement between the purchaser and the supplier. It shall be free from foreign matter and visible impurities)	-	500	-
5.2(5.2 The material shall quickly form a satisfactory lather while in use and shall show no sign of any deterioration on storage in original sealed containers under normal conditions for a period of 12 months.)	-	5000	-
5.3(The soap shall not become liquid at 32°C, and no liquid shall separate when the soap is maintained at 0°C, for 24 h.)	-	1000	-
5.4(Soft soap is liable to lose moisture on keeping. The results obtained for unsaponified and unsaponifiable matter, total free alkali and free caustic alkali by the specific methods of analysis shall, therefore, be recalculated in relation to the specified minimum total fatty matter by means of the equation: Recalculated result = Minimum specified total fatty matter content Actualresult× Actual total fatty matter conten)	-	0	-
Table-1 (i) IS.no 286(Total Fatty Matter ( Type 1 ))	-	1350	-
Table-1 (ii) IS.no 286 CL 12(Unsaponified and Unsaponified matter (Type 1 ))	-	1050	-
Table-1 (iii) IS.no 286 CL 14(Rosin acids percent by mass of total fatty matter ( Type 1))	-	1050	-
Table-1 (iv) IS.no 286 Annex A(Total free alkali ( as K2O ) type 1)	-	950	-
4.5, Table-1 (v) Type-1 & Type-2(Free caustic alkali (as K2O), IS 286)	-	950	-
4.1(Description, IS 7532)	-	300	-

Complete

-
-

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

8574 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3795	Chemical Composition Test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	1117	Dimension and Weight
Cl. 10.7, Fig 5(Total twist, V)	-	1352	Straightness and Twist
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	1790	Tensile, Yield Strength and Elongation Test

Complete

-
-

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

14934 View breakup
Rs.14934/- (10% concession for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5.1, Table-3( CARBON)	-	4895	-
Cl 6(Outer Diameter, Thickness & Mass)	-	1676	-
Cl 7(Workmanship)	-	520	-
8 AND AS PER IS 4736(MASS OF ZINC COATING)	-	1386	Uniformity and Mass of Zinc coating
Cl 9(Workmanship)	-	1352	Straighness
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1790	Tensile Test
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1790	Cold Bend or Flattening Test

Complete

-
-

IS 8931 (1993)

copper alloy fancy single taps, combination tap assembly and stop valves for water services

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(TERMINOLOGY)	-	300	-
Cl 4(NOMINAL SIZES)	-	300	-
Cl 5(Material)	-	10000	-
Cl 6.6(Screw Threads)	-	300	-
Cl 6.7(Waterway)	-	300	-
Cl 6.9(Body Seat)	-	300	-
Cl 6.10(Bonnet assembly)	-	300	-
Cl 6.11(Gland Packaging)	-	300	-
Cl 6.12(Flanges)	-	300	-
Cl 6.13(Knob)	-	300	-
Cl 7.1(Thickness)	-	300	-
Cl 7.2(Body)	-	4500	-
Cl 7.3(Bonnet Assembly)	-	4200	-
Cl 7.3.3(Washer Plate)	-	300	-
Cl 8(Finish)	-	1000	-
Cl 9.2.1(Water Tightness Characteristic)	-	1500	-
Cl 9.2.2(Pressure Resistance Characteristic)	-	1500	-
Cl 9.2.3(Hydraulic characteristic (Flow rate))	-	1500	-
Cl 9.2.4(Mechanical strength characteristic)	-	1500	-

Complete

-
-

IS 9873 : Part 4 (2017)

Safety of toys: Part 4 swings, slides and similar activity toys for indoor and outdoor family domestic use

19700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 and 6.2.1( Strength of toys other than swings)	-	500	-
4.1.2 and A.4.1.2(Maximum height)	-	300	-
4.1.3 and A.4.1.3(Corners and edges on moving parts)	-	300	-
4.1.3 and A.4.1.3(Corners and edges other than moving parts)	-	300	-
4.1.4.1 and 6.7.1 and Fig.6(Protruding parts)	-	500	-
4.1.4.2 and 6.7.1 and Fig.7(All protrusions)	-	500	-
4.1.4.3 and 6.7.1 and Fig.8(Upright protrusions)	-	500	-
4.1.4.4 and 6.7.2 (Motion rides)	-	500	-
4.1.4.5 and 6.7.1.2 and Fig.9(Slides)	-	500	-
4.1.4.5 (Slides)	-	300	-
4.1.5 and A.4.1.5.(Climbing and swinging ropes, chains and cables)	-	300	-
4.1.6 (Open tubing IS 9873 -1 / ISO 8124-1.)	-	500	-
4.2 and A.4.2.(Barriers-Barriers for platforms from 760 mm to 1 000 mm above the ground)	-	300	-
4.2 and A.4.2.(Barriers-Barriers for platforms greater than 1 000 mm and up to 1 830 mm above the ground)	-	300	-
4.2 and A.4.2.(Barriers for platforms more than 1 830 mm above the ground)	-	300	-
4.2 and A.4.2.(Barriers for platforms from 760 mm to 1 000 mm above the ground shall have a maximum vertical opening of 610 mm between the lowermost member of the barrier and the platform that it surrounds.)	-	300	-
4.2 and A.4.2.(Barriers for platforms more than 1 000 mm above the ground shall be designed to minimize the likelihood of climbing. Openings within these barriers or between the barrier and the platform surface shall not permit the passage of the torso probe defined in 6.5.1)	-	300	-
4.2 and A.4.2. and 4.6.2 and 4.6.3(For barriers with an uneven top design)	-	300	-
4.2 and A.4.2. and 6.3(Dynamic strength of barriers and handrails)	-	300	-
4.3(Rung ladders, stepladders and stairways)	-	300	-
4.3 a and Fig.10(The rung or tread shall have a substantial horizontal stepping surface with a lateral width of 240 mm or more)	-	300	-
4.3 b and Fig.10(The distance between the upper surface of the rungs or treads on rung ladders or stepladders shall not be more than 310 mm and on stairways not more 230 mm when measured vertically in accordance with Figure 10.)	-	300	-
4.3 c(The surface of the tread shall not be slippery)	-	300	-
4.3 d(The diameter or cross-sectional dimension of the rungs on rung ladders)	-	300	-
4.3.e(The depth of treads on stepladders with closed risers or stairways)	-	300	-
4.3 f(The inclination of stairways)	-	300	-
4.3 f(The inclination of stepladders)	-	300	-
4.3 f(The inclination of rung ladders)	-	300	-
4.3 g(Stairways and stepladders with a height of 1 200 mm or more above the ground shall be provided with a means of continuous hand support from a height of 760 mm)	-	300	-
4.3 g(A means of continuous hand support from a height of 760 mm)	-	300	-
4.4.1 (Head and neck entrapment)	-	500	-
4.4.2(Entrapment of clothing and hair)	-	500	-
4.4.3(Entrapment of feet)	-	300	-
4.4.4(Entrapment of fingers)	-	300	-
4.5.1(Stability of activity toys other than slides, swings and toys with crossbeams - General)	-	300	-
4.5.2(Stability of activity toys with a free height of fall of 600 mm or less)	-	500	-
4.5.3(Stability of activity toys with a free height of fall of more than 600 mm)	-	300	-
4.6.1 and A.4.6.(Stability of slides)	-	500	-
4.6.2 a and A.4.6.(Retaining sides for slides -For slides with a height of more than 1 000 mm above the ground, the height, h, of the retaining sides shall be 100 mm or more)	-	300	-
4.6.2 b and A.4.6.(Retaining sides for slides - For slides with a height of 1 000 mm or less above the ground, the height, h, of the retaining sides shall be 50 mm or more.)	-	300	-
4.6.3 a and A.4.6.(Starting, sliding and run-out section on slides -The starting section for slides with a height of 1 000 mm or less above the ground shall have)	-	300	-
4.6.3 b and A.4.6.(Starting, sliding and run-out section on slides-The starting section for slides with a height of more than 1 000 mm above the ground shall have)	-	300	-
4.6.3 c and A.4.6.(Starting, sliding and run-out section on slides)	-	300	-
4.6.3 e and A.4.6.(The run-out section for the slide)	-	300	-
4.6.3 f and A.4.6.(The finishing end of the run-out section shall have a radius of 25 mm or more through at least 90°)	-	300	-
4.6.4 and A.4.6.(Roller slides)	-	500	-
4.6.4 and A.4.6.(Roller slides)	-	500	-
4.7.1.1 and A.4.7.(Stability of swings and other activity toys with crossbeams)	-	300	-
4.7.1.2 and A.4.7.(Swings with crossbeams more than 1 200 mm above the ground)	-	300	-
4.7.1.3 and A.4.7.(Swings intended for children under 36 months with crossbeams 1 200 mm or less above the ground)	-	300	-
4.7.2 and A.4.7.2(Strength of crossbeams, swing devices, suspension connectors and suspension couplings)	-	500	-
4.7.3.1(Swings intended for children under 36 months)	-	500	-
4.7.5(Minimum clearance between swing elements, and similar equipment and adjacent structures)	-	300	-
4.7.5(Free swinging elements)	-	500	-
4.7.5(Elements excluding free swinging)	-	500	-
4.7.6 and A.4.7.6(Lateral stability of swing elements - The minimum distance between the suspension points of a swing measured along the crossbeam)	-	300	-
4.7.7(Minimum clearance between swing elements and the ground - The seating surface of swing elements with flexible means of suspension where the crossbeam height is greater than 1 200 mm)	-	300	-
4.7.7(Minimum clearance between swing elements and the ground - The seating surface of swing elements with rigid means of suspension where the crossbeam height is greater than 1 200 mm)	-	300	-
4.7.7(Minimum clearance between swing elements and the ground - The seating surface of swing elements where the crossbeam height is 1 200 mm or less)	-	300	-
4.7.7(Minimum clearance between swing elements and the ground - Footrests of swing elements)	-	300	-
4.7.8 a and A.4.7.8(Suspension connectors and means of suspension)	-	300	-
4.7.8 b and A.4.7.8(Suspension connectors and means of suspension)	-	300	-
4.7.8 c and A.4.7.8(Ropes used as means of suspension - Diameter )	-	300	-
4.7.8 d and A.4.7.8(Straps and chains - Width)	-	300	-
4.7.8 d and A.4.7.8(Accessible chains)	-	300	-
4.7.8 e and A.4.7.8(Suspension connectors and means of suspension)	-	300	-
4.7.8 f and A.4.7.8(Suspension connectors and means of suspension)	-	2000	-
4.8(Seesaws - The central point of the sitting or standing position of the seesaw shall not exceed a height)	-	300	-
4.8(Seesaws - The sitting or standing position of the seesaw may swing out of the horizontal)	-	300	-
4.8(Seesaws )	-	300	-
4.9(Carousels and rocking toys)	-	300	-
4.9(Carousels and rocking toys)	-	300	-
4.9(Free height of fall for carousels and rocking toys)	-	300	-
4.10.1 and A.4.10(Inflatable activity toys - General)	-	300	-
4.10.2 and A.4.10(Inflatable activity toys - Anchorage)	-	300	-
4.10.3 and A.4.10(Connection tubes for continuous inflation)	-	300	-
4.10.4.1 and A.4.10(Containment - General)	-	300	-
4.10.4.2 and A.4.10(Platforms - Any platform intended for sitting or standing)	-	300	-
4.10.4.2 and A.4.10(Containment walls with a minimum height )	-	300	-
4.10.4.2 and A.4.10(Permanently roofed Containment walls)	-	300	-
4.10.4.3 and A.4.10(Slopes shall be treated as a platform.)	-	300	-
4.10.4.3 and A.4.10(The first metre at the top of slopes)	-	300	-
4.10.4.3 and A.4.10(The remaining length of slopes greater than 30° that are 760 mm or more above the ground shall be provided with containing walls with a minimum height of 900 mm.)	-	300	-
4.10.4.4 and A.4.10(Safe collapse)	-	300	-
4.10.4.4 a and A.4.10(When tested in accordance with 6.9 the minimum time taken for the test load to reach its lowest point )	-	300	-
4.10.4.4 b and A.4.10(the opening of any tunnel or squeeze point under any platform shall not be reduced in height by more than 50 % within 30 s.)	-	300	-
4.11.1(Paddling pools - General)	-	300	-
4.11.2(Edges, points, and small parts)	-	300	-
4.11.3(Paddling pools with inflatable walls)	-	300	-
5.1(Labelling)	-	300	-
5.2(Assembly and installation instructions)	-	300	-
5.3(Maintenance instructions)	-	300	-
5.4(Warnings)	-	300	-

Complete

-
-

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

1500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2-5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	500	-
4.2.2(a)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-	500	-
4.2.2(b)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-	500	-
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	500	-
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	500	-
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-	500	-
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	500	-
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	500	-
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	500	-
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	500	-
4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-	500	-
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame)	-	500	-
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	500	-
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	500	-
4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	500	-
4.5-5.5(Soft-filled toys-rate of spread of flame )	-	500	-
4.5-5.5(Soft-filled toys-Test for soft-filled toys )	-	500	-

Complete

-
-

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 - 5.24.2( Reasonably foreseeable abuse -Drop Test)	-	300	-
4.2 - 5.24.3( Reasonably foreseeable abuse -Tip-over test for large and bulky toys)	-	300	-
4.2 - 5.24.4( Reasonably foreseeable abuse -Dynamic strength test for wheeled ride-on toys other than toy scooters)	-	1000	-
4.2 - 5.24.5( Reasonably foreseeable abuse -Torque test)	-	500	-
4.2 - 5.24.6.2( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys)	-	500	-
4.2 - 5.24.6.3( Reasonably foreseeable abuse -Tension test for pompoms)	-	500	-
4.2 - 5.24.6.4( Reasonably foreseeable abuse -Tension test for protective components)	-	500	-
4.2 - 5.24.6.5( Reasonably foreseeable abuse -Tension test for a projectile with a suction cup)	-	500	-
4.2 - 5.24.7( Reasonably foreseeable abuse -Compression test)	-	500	-
4.2 - 5.24.8.2( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent)	-	500	-
4.2 - 5.24.8.3( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent)	-	500	-
4.3.2 - 5.21( Expanding materials)	-	500	-
4.4.1 - 5.2(Small parts-For children under 36 months)	-	300	-
4.4.2 - 5.2(Small parts-For children 36 months and over but under 72 months )	-	300	-
4.5.1.2 - 5.3(Shape, size and strength of certain toys-Squeeze toys, rattles, and certain other toys and components of toys-Test for shape and size of certain toys)	-	300	-
4.5.1.3 - 5.3(Shape, size and strength of certain toys-Other toys or components of toys with nearly spherical, hemispherical, circular flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children under 18 months-Test for shape and size of certain toys)	-	300	-
4.5.1.4 - 5.3(Shape, size and strength of certain toys-Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical, or dome-shaped ends intended for children 18 months and over but under 48 months-Test for shape and size of certain toys)	-	300	-
4.5.2 - 5.4(Shape, size and strength of certain toys-Small balls-Small balls test)	-	300	-
4.5.3 - 5.5(Shape, size and strength of certain toys-Pompoms-Test for pompoms)	-	300	-
4.5.4 - 5.6(Shape, size and strength of certain toys- Pre-school play figures-Test for pre-school play figures)	-	300	-
4.5.5(Shape, size and strength of certain toys-Toy pacifiers-Nipple length)	-	300	-
4.5.6(Shape, size and strength of certain toys-Balloons)	-	300	-
4.5.7(Shape, size and strength of certain toys-Marbles)	-	300	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening)	-	300	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening in Base)	-	300	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening not in Base)	-	300	-
4.5.8 - b(Shape, size and strength of certain toys-Hemispheric-shaped toys-Extension of divider)	-	300	-
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening)	-	300	-
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening )	-	300	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys)	-	300	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys-The maximum distance between centrelines of adjacent peaks )	-	300	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys-Minimum depth)	-	300	-
4.6.1 a - 5.8(Edges-Accessible sharp edges of glass or metal-Sharp edge test)	-	500	-
4.6.1 b(Edges-Accessible sharp edges of glass or metal- gap between the edge and the adjacent surface)	-	500	-
4.6.2(Edges-Functional sharp edges)	-	300	-
4.6.3 - 5.8(Edges-Edges on metal toys-Sharp edge test)	-	500	-
4.6.4( Edges-Edges on moulded toys)	-	500	-
4.6.5( Edges-Edges on exposed bolts or threaded rod)	-	500	-
4.7.1 - 5.9(Points-Accessible sharp points-sharp-point test)	-	500	-
4.7.2 - a(Points-Functional sharp points)	-	500	-
4.7.2 - b(Points-Functional sharp points)	-	500	-
4.7.3 (Wooden toys)	-	500	-
4.8.1(Projections-General requirments)	-	300	-
4.9(a) - 5.24.8.2( Metal wires and rods-wires and other metallic components intended to be bent)	-	500	-
4.9(b) - 5.24.8.3( Metal wires and rods-wires likely to be bent)	-	500	-
4.9 - c( Metal wires and rods)	-	500	-
4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys-average thickness)	-	500	-
4.11.2.1(a) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	300	-
4.11.2.1(b) - 5.11.3( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-breakaway feature separation test)	-	300	-
4.11.2.1(b) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test)	-	300	-
4.11.2.2 - 5.11.2( Cords-Cords in toys intended for children under 18 months--Other cords-free length )	-	300	-
4.11.3.1(a) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	300	-
4.11.3.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords)	-	300	-
4.11.3.3 ( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords without a free end )	-	300	-
4.11.4(a) - 5.11.4.1(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Head probe push test)	-	500	-
4.11.5 - 5.11.2(Cords-Cords on pull toys-free length)	-	300	-
4.11.6(Cords- Electrical cables)	-	300	-
4.11.7 - 5.11.1(Cords- Diameter of certain cords intended for children under 36 months-cords cross-sectional dimension)	-	300	-
4.11.8 - 5.11.5(Cords- Self-retracting cords intended for children under 36 months-self-retracting cords)	-	300	-
4.11.9.1(Cords-Toys intended to be strung across a cradle, cot, perambulator or carriage)	-	300	-
4.11.9.2 (Cords-Toys otherwise intended to be attached to a cradle, cot, perambulator or carriage)	-	300	-
4.11.10(Cords-Cords on toy bags)	-	300	-
4.11.11 - 5.11.6( Cords, strings and lines for flying toys- electrical resistance)	-	300	-
4.12.1(a - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.1(a - 2)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.1(a - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators)	-	500	-
4.12.1(a - 4)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.1(a - 5) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.1(b - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.1(b - 2) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.1(b - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.2 (a) - 5.22.3(Folding mechanisms-Other toys with folding mechanisms)	-	300	-
4.12.2 (b)(Folding mechanisms-Other toys with folding mechanisms)	-	300	-
4.12.3(Folding mechanisms-Hinge line clearance)	-	300	-
4.13.1(Holes, clearances and accessibility of mechanisms-Circular holes in rigid materials)	-	300	-
4.13.2 (Holes, clearances and accessibility of mechanisms-Accessible clearances for movable segments)	-	300	-
4.13.3(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys)	-	300	-
4.13.3 - 5.7(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys-accessibility of a part or component)	-	300	-
4.13.4(Holes, clearances and accessibility of mechanisms-Other driving mechanisms)	-	300	-
4.13.5(Holes, clearances and accessibility of mechanisms-Winding keys)	-	300	-
4.14(a)(Springs)	-	300	-
4.14(b)(Springs)	-	300	-
4.14(c)(Springs)	-	300	-
4.15.1.1 - 5.12.2( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet available for stabilization)	-	500	-
4.15.1.2 - 5.12.3( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet unavailable for stabilization)	-	500	-
4.15.1.3 - 5.12.4( Stability and overload requirements-Stability of ride-on toys and seats-Fore and aft stability Test)	-	500	-
4.15.2 - 5.12.5( Stability and overload requirements-Overload requirements for ride-on toys and seats-overload test for ride-on toys and seats)	-	500	-
4.15.2 - 5.24.4( Stability and overload requirements-Overload requirements for ride-on toys and seats-dynamic strength test for wheeled ride-on toys other than toy scooters)	-	500	-
4.15.3 - 5.12.6( Stability and overload requirements-Stability of stationary floor toy-Stability test of stationary floor toys)	-	500	-
4.16.1(Enclosures-Ventilation)	-	300	-
4.16.2.2(a)(Enclosures-Closures-Lid support for toy chests and similar toys)	-	2000	-
4.16.3(Enclosures-Toys that enclose the head)	-	300	-
4.17 - 5.14(Simulated protective equipment, such as helmets, hats and goggles-Impact test for toys that cover the face)	-	500	-
4.18.2(a) - 5.36(Projectile toys-Projectiles-tip assessment of rigid projectiles)	-	300	-
4.18.2(b)(Projectile toys-Projectiles)	-	300	-
4.18.2(c)(Projectile toys-Projectiles)	-	300	-
4.18.2(d) - 5.37(Projectile toys-Projectiles-length of suction cup projectiles)	-	300	-
4.18.2 - e - 5.24.5(Projectile toys-Projectiles-torque test)	-	300	-
4.18.3(a) - 5.2(Projectile toys-Projectile toys with stored energy-small parts test)	-	1500	-
4.18.3(a) - 5.4(Projectile toys-Projectile toys with stored energy--small parts test after (wall impact test for projectiles)	-	1500	-
4.18.3(b)(Projectile toys-Projectile toys with stored energy)	-	1500	-
4.18.3(c ) - 5.24.5(Projectile toys-Projectile toys with stored energy-torque test)	-	1500	-
4.18.3(d) - 5.15.2(Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles)	-	1500	-
4.18.3(e )(Projectile toys-Projectile toys with stored energystored energy-Discharge mechanism)	-	1500	-
4.18.4.1 - 5.20(Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys)	-	1000	-
4.18.4.2(a) - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-determination of the kinetic energy per area of contact when the contact area of the dart shall be at least 3 cm^2)	-	300	-
4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart)	-	1500	-
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After torque test)	-	300	-
4.18.4.3 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-kinetic energy per area)	-	300	-
4.18.4.3 - 5.15.2(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-wall impact test for projectiles)	-	300	-
4.18.4.3(a)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	300	-
4.18.4.3(b)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	300	-
4.18.4.3(c)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	300	-
4.19(Rotors and propellers)	-	300	-
4.2(Aquatic toys)	-	300	-
4.21(a)(Braking-brake performance for mechanically or electrically powered ride-on toys other than toy bicycles)	-	500	-
4.21(b)(braking)	-	500	-
4.22.1(Toy bicycles-Instructions for use)	-	500	-
4.22.2(Toy bicycles-Determination of maximum saddle height)	-	300	-
4.22.3 - 5.16.1(Toy bicycles-Braking requirements-determination of free-wheeling facility)	-	500	-
4.22.3 (Toy bicycles-Braking requirements- brake lever dimension(d))	-	300	-
4.22.3 (Toy bicycles-Braking requirements- lever Length(l))	-	300	-
4.22.3 - 5.16.3(Toy bicycles-Braking requirements- brake performance for toy bicycles)	-	500	-
4.23 - 5.17(Speed limitation of electrically driven ride-on toys-determination of speed of electrically driven ride-on toys)	-	500	-
4.24(a) - 5.18(Toys containing a heat source-determination of temperature increases)	-	300	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand-(Parts made of metals))	-	300	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of glass or porcelain))	-	300	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of Plastic or wood ))	-	300	-
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy(Parts made of metals))	-	300	-
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy( Parts made of other materials))	-	300	-
4.25 - 5.19(Liquid-filled toys-leakage of liquid-filled toys)	-	300	-
4.25(Liquid-filled toys)	-	300	-
4.26(a) - 5.2( Mouth-actuated toys-small parts test)	-	300	-
4.26(b) - 5.24.5 - 5.3( Mouth-actuated toys-small parts test after torque test)	-	500	-
4.26(b) - 5.24.6.1 - 5.4( Mouth-actuated toys-small parts test after tension test, general procedure)	-	500	-
4.26(c ) - 5.20 - 5.2( Mouth-actuated toys-small parts test after durability of mouth-actuated toys)	-	1000	-
4.27(Toy roller skates, toy inline skates and toy skateboards)	-	300	-
4.28( Percussion caps specifically designed for use in toys)	-	300	-
4.29(a) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1000	-
4.29(b) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1000	-
4.29(c) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1000	-
4.29(d) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1000	-
4.29(e) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1000	-
4.29(f) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1000	-
4.29(g) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1000	-
4.30.2(Toy scooters-Warnings and instructions for use)	-	300	-
4.30.3 - 5.26 - 5.8(Toy scooters-Strength-After static strength for toy scooters- sharp edge test)	-	500	-
4.30.3 - 5.26 - 5.9(Toy scooters-Strength-static strength for toy scooters-sharp-point test)	-	500	-
4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters)	-	500	-
4.30.3 - 5.27(Toy scooters-Strength-dynamic strength for toy scooters)	-	500	-
4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes)	-	500	-
4.30.4 - 5.12.2(Toy scooters-Stability-sideways stability test, feet available for stabilization)	-	500	-
4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	300	-
4.30.5(b)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	300	-
4.30.5(c)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	300	-
4.30.5(d)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	300	-
4.30.5(e)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	300	-
4.30.5(f) - 5.30( Toy scooters-Adjustable and folding steering tubes and handlebars-resistance to separation of handlebar)	-	300	-
4.30.6 ( Toy scooters-Braking)	-	500	-
4.30.6 - 5.28( Toy scooters-Braking- force required to hold the toy)	-	500	-
4.30.7( Toy scooters-Wheel size(diameter))	-	300	-
4.30.8(Toy scooters-Projections)	-	300	-
4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs Diameter))	-	300	-
4.32 - 5.38.2( Yo-yo balls - length (lo) of the yo-yo ball tether)	-	500	-
4.32 - 5.38.1( Yo-yo balls - The ratio of the mass m (in grams) to the elastic constant k of the yo-yo ball tether(m/k))	-	500	-
4.33 - 5.11.3(Straps intended to be worn fully or partially around the neck-breakaway feature separation test)	-	300	-
4.34(Sledges and toboggans with cords for pulling)	-	300	-
4.35.3 - 5.39(Jaw entrapment in handles and steering wheels-jaw entrapment test)	-	500	-

Complete

-
-

IS 13395 (1995)

Performance of handles and handle assemblies attached to cookware - Specification

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	300	-
5.2(Bending Strength)	-	1500	-
5.3(Torque Strength)	-	1500	-
5.4(Impact Strength)	-	1500	-
5.5(Fatigue Resistance)	-	1500	-
5.6(Leakage)	-	500	-
5.7(Thermal Insulation)	-	500	-
5.8(Heat Resistance)	-	500	-
5.9(Washing Resistance)	-	500	-
5.1(Burning Resistance)	-	500	-

Complete

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

28600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15.1 a) i)(Annealing Test ( For copper wire ) )	-	2000	50% for Additional Core
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	2200	50% for Additional Core
15.1 a) iv)(Resistance test - Neutral conductor)	-	2000	50% for Additional Core
9.3(Thickness of Insulation - Minimum)	-	2000	50% for Additional Core
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	2000	50% for Additional Core
15.1 e) vi) (Sheath : Heat shock test)	-	2000	50% for Additional Core
15.1 e) v) (Sheath : Hot deformation)	-	2500	50% for Additional Core
16.2(HIGH VOLTAGE TEST )	-	4000	50% for Additional Core
16.9(Oxygen Index Test)	-	10000	50% for Additional Core
16.14(Temperature Index)	-	10000	50% for Additional Core
16.13(Test for Halogen Acid Gas Evolution)	-	10000	50% for Additional Core
16.11(Flame Retardance Test on Bunched Cables)	-	20000	50% for Additional Core
15.1 a) iii)(Wrapping test (for aluminium))	-	2000	50% for Additional Core
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	2000	50% for Additional Core
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	5000	50% for Additional Core
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	5000	50% for Additional Core
16.3(FLAMMABILITY TEST : Period of Burning )	-	2000	50% for Additional Core

Complete

-
-

IS 14951 (2001)

Fire extinguisher - 145 litres capacity mechanical foam type - Specification

11550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Capacity)	-	300	-
Cl 6(Shape)	-	300	-
Cl 7.1(General)	-	300	-
Cl 7.2(Body)	-	300	-
Cl 7.3(Carrying Handle)	-	300	-
Cl 7.4(Neck Ring)	-	300	-
Cl 7.5(Cap)	-	300	-
Cl 7.6(Snifter valve)	-	300	-
Cl 7.7(Safety Pressure release valve)	-	1500	-
Cl 7.8(Liquid Level Indicator)	-	300	-
Cl 7.9(Hose)	-	600	-
Cl 7.10(Foam Making Branch & Other Discharge Fittings)	-	300	-
Cl 7.11(Siphon Tube)	-	300	-
Cl 7.12(Drain Plug)	-	300	-
Cl 7.13(Wheeled Carriage)	-	900	-
Cl 9(Anti Corriosive Treatment)	-	1350	-
Cl 10(Painting)	-	1200	-
Cl 11.1(Discharge Test)	-	900	-
Cl 11.3(Hydraulic Pressure Test)	-	1500	-
Cl 11.4(Burst Test)	-	1500	-

Complete

-
-

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

3900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Tables 2 to 9(Types)	-	300	-
5.1 Tables 2 to 9 (2)(Size of Hinge)	-	300	-
5.1 Tables 2 to 9 (3)(Length A)	-	300	-
5.1 Tables 2 to 9 (4)(Breadth B)	-	300	-
5.1 Tables 2 to 9 (4)(Breadth B1)	-	300	-
5.1 Tables 2 to 9 (4)(Breadth B2)	-	300	-
5.1 Tables 2 to 9 (5)(Thickness of Flap C)	-	300	-
5.1 Tables 2 to 9 (6)(Diameter of Hinge Pin D)	-	300	-
5.1 Tables 2 to 9 (7)(Number of Knuckles)	-	300	-
5.1 Tables 2 to 9 (8)(Number of Screw Holes)	-	300	-
5.1 Tables 2 to 9 (9)(Holes for Screw No.)	-	300	-
6.1(General)	-	300	-
6.1(General)	-	300	-
6.1(General)	-	300	-
6.2.1(Knuckles)	-	300	-
6.3(Pins)	-	300	-
6.4(Screw Holes)	-	300	-
6.4.2(Position of Holes)	-	300	-
6.4.2(X)	-	300	-
6.4.2(Y)	-	300	-
6.4.2(Z)	-	300	-
6.4.2.1(Position of Holes)	-	300	-

Complete

-
-

IS 903 (1993)

Specification for Fire Hose Delivery Couplings, Branch Pipe, Nozzles And Nozzle Spanner - Specificaion

29800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Finish and workmanship)	-	300	-
4(Marking)	-	300	-
6(Branch pipe)	-	5000	-
6.3(Hydraulic test requirement)	-	1500	-
7(Nozzle)	-	5000	-
7.3(Hydraulic test requirement)	-	1500	-
5.3(Size and Dimension )	-	10000	-
5.4(Hydraulic test requirement)	-	1500	-

Complete

-
-

IS 17153 (2019)

Domestic gas stoves for use with piped natural gas (PNG) - Specification

14100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
26(Burner-5)	-	2500	-
26(Burner-4)	-	2000	-
26(Burner-3)	-	1500	-
26(Burner-2)	-	1000	-
26(Burner-1)	-	1000	-
25.2(With the Burner lighted on full on, the flame temperature at a height of H+20 mm)	-	300	-
25.1(Temperature of synthetic rubber diaphragm in gas carrying components)	-	300	-
25.1(Temperature of the surface in normal use)	-	300	-
25.1(Temperature of the portion of the surface other than the working surface likely to be touched accidentally.)	-	300	-
25.1(Rise of Temperature above room temperature in (Wall, Floor, Ceiling), after two hours of operation)	-	1000	-
24(Burner-5)	-	300	-
24(Burner-4)	-	300	-
24(Burner-3)	-	300	-
24(Burner-2)	-	300	-
24(Burner-1)	-	300	-
23(When operated at pressure 20-25 gf/cm2 , there shall be no extinction of flame on any of the burneroperating at the max of the burner, when the appliance is placed in normal current of air with velocity of 2 m/s.)	-	300	-
22(When operated at pressure 20-25 gf/cm2 , for one at full on position, no soot shall be deposited on burner or on the bottom of the vessel.)	-	300	-
21(When operated at pressure 20-25 gf/cm2 for half an hour flame shall be reduced to simmer and then brought back to full on, operation shall be repeated five times, no flash back shall occur during the test.)	-	300	-
20(Ignition of Burner flame, their operation and turning off shall not give rise to undue excessive noise during the operation.)	-	300	-
19.3(Fixed Min Pilot flame shall be sufficient to relight the main burner at the 21 mbar gas inlet pressure.)	-	300	-
19.2(Pilot Flame shall be Stable without lifting or soot deposition at gas inlet pressure from 20-25 gf/cm2)	-	300	-
19.1.1(When the gas consumption of the burner is reduced to simmer after operating half an hour on full ON flame shall not extinguish, blow off, strike back or form soot at 21 mbar gas inlet pressure.)	-	300	-
19.1(It shall be possible to operate stove with taps fully open at gas inlet pressure , without the flame extinguishing, blowing off or striking back and without the formation of soot.)	-	300	-
18.3(When the burner is ignited from a pilot flame and/or by an electric/electronic method, the ignition and flame travel shall be smooth at pressure……..)	-	300	-
18.4.1(The flame failure device if provided shall confirm to IS:5116)	-	300	-
18.2(if the flame is applied to any of the outer row of the burner ports when the gas is flowing , flame travel shall be complete……..)	-	300	-
18.1(Where the burner or burners are lighted by automatic ignition (Battery of flint operated or by a pilot flame , it shall not be possible for gas to be admitted to the main burner without being smoothly ignited by the pilot flame. Each burner should be at room temperature at the begining of the test and should be tested in turn. )	-	300	-
18.1(There shall be easy and safe access of lighting each burner by matchstick and it shall be easy to see that the burner is lighted)	-	300	-
17.3(When the gas consumption of the burner is reduced to simmer, the flame shall not extinguish, blow off, strike back or form soot, when tested with commercial PNG at 21 mbar gas inlet pressure.)	-	300	-
17.2(Burner-5)	-	300	-
17.2(Burner-4)	-	300	-
17.2(Burner-3)	-	300	-
17.2(Burner-2)	-	300	-
17.2(Burner-1)	-	300	-
17.2(Sim Rating Declared)	-	300	-
17.1.2(Total Gas Consumption)	-	300	-
17.1(Burner-5)	-	300	-
17.1(Burner-4)	-	300	-
17.1( Burner-3)	-	300	-
17.1( Burner-2)	-	300	-
17.1( Burner-1)	-	300	-
17.1(Rating Declared)	-	300	-
15.2(Fragmentation test of the toughened glass to )	-	300	-
15.1(Verification of the strength of the gas stove surface of the toughened glass top against thermal stress)	-	300	-
15(Width wise deflection)	-	300	-
15(Length wise deflection)	-	300	-
15(Vertical Deflection)	-	300	-
14.5(The position of the gas inlet shall allow connection to a gas supply on either side of the appliances, the rear end or bottom is also permitted. It shall be possible to change gas inlet from one side to other side easily by standard tools.)	-	300	-
14.4(Any other connection made from the main gas rail shall be only metallic.)	-	300	-
14.4(The external surface of the gas rail shall be treated to resist corrosion)	-	300	-
14.4(The wall thickness of main gas rail)	-	300	-
14.4(The pipe/tube used for main gas rail shall be of mild steel)	-	300	-
14.3(Screwed gas Inlet and outlet connections shall confirm to IS:554, Declared by party)	-	300	-
14.2((e))	-	300	-
14.2((d))	-	300	-
14.2(( c))	-	300	-
14.2((b))	-	300	-
14.2(Shape of Nozzles as per fig. 3 : (a))	-	300	-
14.2(Where Nozzles for flexible tubing are fitted, they shall be so positioned as to facilitate fitting of the tubing and also to prevent heating of the tubing to more than 60°C)	-	300	-
14.1(Nozzle shall be machined from free cutting brass, MS, SS, Zinc)	-	300	-
13(All gas carrying parts of the appliances should be sound and these parts when connected to form complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m²)	-	300	-
12.1.2(The material of the pan support shall be metallic.)	-	300	-
12.1.1(Loose Pan support shall be so designed that it is not possible to place them firmly in other than proper position)	-	300	-
12.1(Prongs of the Support shall have suitable taper to accommodate round bottom pans.)	-	300	-
12.1(The design of the pan supports shall be such that it is practicable to support a pan of 100 mm diameter over at least one top burner without the use of loose rings and such that 125 mm diameter vessel remains stable over each burner. )	-	300	-
11.7(The appliance comprising two or more burners shall include one burner having a rating of at least 1450 kCal/hr, based on net calorific value of the gas (When using domestic PNG))	-	300	-
11.6(For Burners having centre flame, provision shall be made to protect the centre flame from pan resting directly on burner top and smothering the centre flame. )	-	300	-
11.5(If the burner is made and assembled in two or more parts they shall be so designed to provide proper self locating arrangement so that they are always reassembled to its original design preventing any maladjustment in their assembly. This shall also be applicable for primary air regulators.)	-	300	-
11.4(If primary air regulators are used, they shall be so designed that they are not easily maladjusted by the user and the construction shall be such that primary air adjustment can be made with the burner in place.)	-	300	-
11.3(The tightness of the joints in the burner assembly shall not be depended upon adhesives or any kind of packing.)	-	300	-
11.2(The Burner supports shall be rigid and shall be fixed in their place. Their construction shall ensure the stability of the burners and shall prevent their undue movement in a horizontal plane.)	-	300	-
11.1(The construction of the burners and the assembly shall allow their dismantling from the supports easily with or without the use of tools)	-	300	-
10.2(The Size of the jet in Litres per hour of flow of PNG at STP conditions shall be impressed upon it.)	-	300	-
10.1.1(Injector Jet shall be made of metal , with or without ceramic tip. The melting point of the metal shall not be less than 650°C)	-	300	-
10.1(Dimension- Across Flats)	-	300	-
10.1(Dimension- Threads)	-	300	-
10.1(Dimension- Projection from the face of mounting, Nominal)	-	300	-
10.1(The Injector Jets shall be fixed calibrated type and it shall not be possible to loosen them without the use of tools.)	-	300	-
9.12(The noting means adopted shall be sufficiently robust to withstand normal use without distortion or damage.)	-	300	-
9.11.1(Simmer flame shall be obtained by fixed simmer orifice.)	-	300	-
9.11(Taps having an 'OFF' position shall have positive stops at the 'OFF' and simmer position except that special purpose taps (for appliance incorporating auto or self ignition device))	-	300	-
9.1(Screw-down valves shall be so designed that it is impossible to withdraw completely the valve stem in the normal operation of the tap.)	-	300	-
9.9(Screws nuts etc., which regulate the tension of taps valve or springs shall not loosen in operation of the appliance. It shall not be possible to cause a leak during normal manual operation of tap.)	-	300	-
9.8(All controls or taps shall be easy to operate at all temperatures normally attained in use)	-	300	-
9.7(C1)	-	300	-
9.7(B1)	-	300	-
9.7(A1)	-	300	-
9.7(D)	-	300	-
9.7(C)	-	300	-
9.7(B)	-	300	-
9.7(A)	-	300	-
9.7(Dimension of Taper plugs in off position:)	-	300	-
9.6(Each taper plug tap shall be spring loaded to maintain a gas tight fit. Helical springs fitted in taps and valves shall have flattened ends, which shall be rounded before fitting.)	-	300	-
9.5.1(Taps shall be lubricated with suitable grease, resistant to the action of the gas and capable of operating at the maximum temperature of 110°C.)	-	300	-
9.5(Taps shall be so made that in normal use and reasonable application of lubricant, the gas passages do not become blocked.)	-	300	-
9.4(Preferably all taps (Excluding pilot taps) should lock in the off position, but in all cases it shall be impossible to handle or tap to move accidentally…. )	-	300	-
9.3(When Taps are fitted with adjustable stops, there shall be means of looking the stops in position. If screws are used for this purpose, they shall not lead into gas passages.)	-	300	-
9.2(Taps shall be designed so that when placed in any position and viewed from a distance of 3 m, will definitely indicate whether the valve is open, closed or in intermediate position.)	-	300	-
9.2(All Taps shall close in the same direction. The direction of rotation of knob from off-on-simmer shall be anti-clockwise.)	-	300	-
9.2(The 'ON' "OFF" and any fixed position of tap handles shall be clearly and durably indicated or shall be obvious by design or position else some indication shall be provided.)	-	300	-
9.1(The Appliance shall have at least one tap for each burner)	-	300	-
8.7(The external Finished surfaces shall be easily cleanable.)	-	300	-
8.6(All springs, screws, nuts and bolts which are visible or to be removed for maintenance, shall be of corrosion-resistant material or treated to resist corrosion.)	-	300	-
8.5(Concealed Gas Supplies: Concealed tubular fittings liable to corrode shall be protected by bituminous paint or other equally protective material.)	-	300	-
8.4 (b)(Resistance to Heating)	-	300	-
8.4 (a)(Resistance to Abrasion)	-	300	-
8.3.3(Corrosion Resistance test)	-	300	-
8.3.2(Adhesion Test)	-	300	-
8.3.1(Thickness of Chromium coating)	-	300	-
8.3(Thickness of Nickel coating of the top flat surface of the body of electroplated stove.)	-	300	-
8.1(The finishes shall, on visual examination, show no defects, such as pin-holes, blisters, roughness or exposed area of metal, which give rise to undualy rapid deterioration in use.)	-	300	-
8.1(Parts, which will come in contact with the foodstuff, shall be capable of being hygienically cleaned.)	-	300	-
8.1(The Finish of exposed parts shall be durable, easy to clean and not subject to excessive deterioration in normal use.)	-	300	-
7(Rigidity and Stability : The appliance shall be so designed that it remains stable and shall not be easily overturned.)	-	300	-
6.7(Thickness of Sheet)	-	300	-
6.6(All nuts, bolts and fittings having spanner flats shall be capable of being moved by suitable spanner or be readily accessible to an adjustable spanner.)	-	300	-
6.5(Parts, which are intented to be removable by the user, shall be easy to replace correctly and difficult to assemble incorrectly.)	-	300	-
6.4(Burners and parts of Burner only of same rating , model and make shall be interchangeable or replaceable without effecting performance.)	-	300	-
6.3(Burner ports shall be so designed and located that in normal use spilage of food shall not cause internal fouling of mixing tube and or blockage of injector jet.)	-	300	-
6.2(The relative distance between the centres of the adjoining burner-)	-	300	-
6.2(the parts of the burner shall not become disconnected during operation of the appliance.)	-	300	-
6.1(The appliance, including all the component parts, shall be easy to clean and maintain in good working order, there shall be easy access to the accessories and controls for maintenance and adjustment.)	-	300	-
5.8.3(The number of glass fragments contained in a 50 mm side square, when tested as Cl. 15.2)	-	300	-
5.8.3(Toughened glass shall fragment into small particles.)	-	300	-
5.8.2(Pan support for an uncovered burner in contact with the glass ceramic surface.The surface area of the pan support in contact with the glass ceramic)	-	300	-
5.8.2(The toughened glass top shall ensure durability against damage in normal use)	-	300	-
5.8.2(The means to hold the glass top of the gas stove shall not allow any stress or risk of mechanical change to the glass top.)	-	300	-
5.8.1(Toughened glass top including their edges or corners shall not have fissures or scratches)	-	300	-
5.7(Drip tray if provided shall be made of non-corrosive material)	-	300	-
5.6(Meltiing poin of metal used in oven, griller or auxilliary or anyother combination)	-	300	-
5.6(Melting point of metal for burner top)	-	300	-
5.5(The main body of the burner including mixer head, mixing tube and burner head shall be of substantial and durable construction)	-	300	-
5.4(Change in weight or volume of a non metallic material, when immerse in n-Pentane or PNG for 72 hours)	-	300	-
5.3(Mercurous Nitrate test for copper and copper alloy Parts)	-	2500	-
5.2(The burner parts shall not melt or distort when burner is operated with flames flashed back for half an hour in the mixing tube.)	-	300	-
5.1.1(Plastic components which are liable to heating (For example, tap handles push buttons etc.) shall be free of fissures, distortion, blemishes and discolouration)	-	300	-
5.1(The use of low pressure rubber or plastic tubing fitted or pushed on nozzle is not recommended.)	-	300	-
5.1(If flexible tubing is used, it shall not be fitted on the outlet side of any control which is capable of cutting of the gas completely, except where screwed metal connection are fitted.)	-	300	-
5.1(The appliance shall be free from swarf, grit and other foreign matters.)	-	300	-
4.3(No pressure regulator shall be included as part of the stove.)	-	300	-
4.2(Rivets, Fastening screws and plugs , etc. shall not lead into gas passages.)	-	300	-
4.1(The construction of all the parts of equipment shall be sound and of high standard of workmanship and appropriate finish. The construction shall ensure durability and shall comply with the safety requirements.)	-	300	-
8.2(Vitreous enameled component shall meet the requirement when tested in accordance with Annex E of IS:5116)	-	900	-

Complete

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

38500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	2000	50% for Additional Core
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	2000	50% for Additional Core
7.2( Thickness of insulation)	-	2000	50% for Additional Core
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	5000	50% for Additional Core
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	2000	50% for Additional Core
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	2000	50% for Additional Core
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	2000	50% for Additional Core
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	2000	50% for Additional Core
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	5000	50% for Additional Core
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	5000	50% for Additional Core
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	2000	50% for Additional Core
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	5000	50% for Additional Core
10.1 g)(High voltage test - IS10810:Part 45)	-	4000	50% for Additional Core

Complete

-
-

IS 302 : Part 2 : Sec 6 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 6 cooking ranges, hobs, ovens and similar appliances (First Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Marking and instructions)	-	2000	-
8.0(Protection against access to live part test)	-	2500	-
10.0(Power Input and current test)	-	2500	-
11.0(Heating test)	-	3000	-
13.0(Leakage current and electric strength test)	-	4000	-
14.0(Transient voltages)	-	4000	-
15.0(Moisture Resistance)	-	4000	-
16.0(Leakage current and electric strength test)	-	4000	-
17.0(Overload protection of transformers test)	-	2000	-
19.0(Abnormal Operations)	-	2000	-
21.0(Mechanical Strength)	-	5000	-
25.0(Supply connections and External Flexible Cords)	-	2000	-
26.0(Terminal for External Conductors)	-	2000	-
27.0(Provision for Earthing)	-	2000	-
28.0(Screws and connections)	-	2000	-
30.0(Resistance to heat and fire)	-	4000	-
31.0(Resistance to rusting)	-	2500	-
20.0(Stability and Mechanical Hazards)	-	2000	-
29.0(Clearances and Creepage distances and solid insulation)	-	2000	-

Complete

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

28600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	2000	50% for Additional Core
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	2000	50% for Additional Core
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	2000	50% for Additional Core
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	2000	50% for Additional Core
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	2000	50% for Additional Core
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	2200	50% for Additional Core
9.2(INSULATION : Thickness of Insulation)	-	2000	50% for Additional Core
16.5(Oxygen Index Test)	-	10000	50% for Additional Core
16.4(Flammability Test)	-	2000	50% for Additional Core
16.1(Temperature Index)	-	10000	50% for Additional Core
16.9(Test for Halogen Acid Gas Evolution)	-	10000	50% for Additional Core
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	2000	50% for Additional Core
15.1 d)5)( Loss of mass in air oven- Insulation )	-	5000	50% for Additional Core
15.1 d)5)( Loss of mass in air oven- sheath )	-	5000	50% for Additional Core
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	2000	50% for Additional Core
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	2000	50% for Additional Core
15.1 d)6)(Heat shock test- Insulation )	-	2000	50% for Additional Core
15.1 d)6)(Heat shock test- sheath )	-	2000	50% for Additional Core
15.1 d)4)(Hot deformation : Insulation )	-	2500	50% for Additional Core
15.1 d)4)(Hot deformation : Sheath )	-	2500	50% for Additional Core
15.1 d)7)(Thermal stability- insulation )	-	4000	50% for Additional Core
15.1 d)7)(Thermal stability- Sheath )	-	4000	50% for Additional Core
15.1 e)(Insulation resistance test : Volume Resistivity )	-	2000	50% for Additional Core
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	3000	50% for Additional Core
15.1 f)(High voltage test ( water immersion test ))	-	4000	50% for Additional Core
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	4000	50% for Additional Core
15.1 g)(High voltage test at room temperature)	-	4000	50% for Additional Core

Complete

-
-

IS 302 : Part 2 : Sec 80 (2017)

Household and similar electrical appliances - Safety: Part 2 - 80 particular requirements for fans (First Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0(Protection against access to live parts)	-	2500	-
10.0(Input and Current)	-	2500	-
11.0(Heating)	-	3000	-
13.0(Leakage Current and electric strength at operating temperature)	-	4000	-
14.0(Transient Overvoltage)	-	2000	-
15.0(Moisture resistance)	-	4000	-
16.0(Leakage current and Electric strength (After Humidity (Environmental) Treatment))	-	4000	-
17.0(Overload Protection of transformer and associated circuit)	-	2000	-
19.0(Abnormal Operation)	-	4000	-
21.0(Mechanical Strength)	-	2000	-
25.0(Supply Connection and External Flexible Cords)	-	2000	-
26.0(Terminals for external conductors)	-	2000	-
27.0(Provision For Earthing)	-	2000	-
28.0(Screws and Connections)	-	2000	-
30.0(Resistance To Heat and Fire)	-	4000	-
31.0(Resistance To Rusting)	-	2500	-
20.0(Stability and mechanical hazards)	-	5000	-
29.0(Creepage Distances and Clearances)	-	2500	-

Complete

-
-

IS 374 (2019)

Specification for electric ceiling type fans and regulators (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017))	-	2500	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	4000	-
9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017))	-	2000	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	4000	-
9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017))	-	4000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	2000	-
9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017))	-	5000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	2000	-
9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017))	-	2000	-
9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017))	-	2000	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	2500	-
9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017))	-	4000	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	2500	-
9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017))	-	2500	-
9(Construction (as per Cl.22.101 of IS 302-2-80 :2017))	-	2000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	2000	-
9(Components (as per Cl.24.103 of IS 302-2-80 :2017))	-	2000	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	2000	-
14.3 & Table 1(Test for Air Performance)	-	4500	-
11.1(Starting)	-	1000	-
11.2(Starting)	-	1000	-
12(Interchangeability)	-	1000	-
14.4(Measurement of Speed of the Fan )	-	2000	-
14.5(Measurement of Power factor and Power Input)	-	2000	-
17(Test for Harmonic Distortion)	-	3000	-
10.1(Speed Regulators)	-	2000	-
8.1(Marking (as per Cl. 7 of IS 302-2-80:2017))	-	1000	-
8.1,a(Marking )	-	1000	-
8.1,b(Marking )	-	1000	-
8.1,c(Marking )	-	1000	-
8.1,d(Marking )	-	1000	-
8.1,e(Marking )	-	1000	-
8.1,f(Marking )	-	1000	-
8.1,g(Marking )	-	1000	-
8.2(Marking )	-	1000	-
8.3,a(Marking )	-	1000	-
8.3,b(Marking )	-	1000	-
8.3,c(Marking )	-	1000	-
8.3,d(Marking )	-	1000	-
8.3,e(Marking )	-	1000	-
8.4(Marking )	-	1000	-
8(Marking (as per Cl. 7.1 of IS 302-2-80:2017))	-	1000	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008))	-	1000	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008))	-	1000	-
8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017))	-	1000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	4000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	2000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	2000	-
6.2(Rating)	-	1000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	2000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	2000	-
9(Components (as per Cl.24.104 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	2500	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	2500	-
10.2(Speed Regulators)	-	2000	-
10.2(Speed Regulators)	-	2000	-
10.2(Speed Regulators)	-	2000	-
10.3(Speed Regulators)	-	2000	-
10.4(Speed Regulators)	-	2000	-
10.5(Speed Regulators)	-	2000	-
10.6(Speed Regulators)	-	2000	-
10.7(Speed Regulators)	-	2000	-
10.7(Speed Regulators)	-	2000	-
10.8(Speed Regulators)	-	2000	-
14.3 & Table 1(Test for Air Performance)	-	4500	-
16(Endurance Test)	-	4000	-
16(Endurance Test)	-	4000	-
16(Endurance Test)	-	4000	-
14.5(Measurement of Power factor and Power Input)	-	2000	-
16(Endurance Test)	-	4000	-
16(Endurance Test)	-	4000	-

Complete

-
-

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl.8 of IS 302-2-21:2011)(Protection Against Access to Live Parts)	-	2500	-
(Cl.10 of IS 302-2-21: 2011)(Power Input & Current)	-	2500	-
(Cl.11 of 302-2-21:2011)(Heating)	-	3000	-
(Cl.13 of IS 302-2-21:2011)(Leakage Current )	-	4000	-
(Cl.14ofIS302-2-21:2011)(Transient Over Voltages)	-	2000	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	4000	-
Cl.16 of IS 302-2-21-2018(Leakage current and Electric strength (After humidity): Leakage current )	-	4000	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	2000	-
(Cl.21ofIS302-2-21:2011)(Mechanical strength)	-	2000	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	2000	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	2000	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	2000	-
(Cl.28 of IS 302-2-21:2011)(Screws & Connections)	-	2000	-
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	4000	-
Cl.31 of IS 302-2-21:2018(Resistance to Rusting)	-	2500	-
(Cl.29ofIS302-2-21:2011)(Clearances, Creepage Distances and Solid Insulation)	-	25000	-

Complete

-
-

IS 369 (2019)

Household electric direct - Acting room heaters - Performance requirements (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.8 of IS 302-2-30:2007 &IS:302-1:2008(Protection Against Access to Live Parts)	-	2500	-
Cl.10 of IS 302-2-30:2007 &IS:302-1:2008(Power Input and Current)	-	2500	-
Cl.13 of IS 302-2-30:2007 &IS:302-1:2008(Leakage Current & Electric Strength at operating temp)	-	4000	-
Cl.14 of IS 302-2-30:2007 &IS:302-1:2008(Transient Over Voltages)	-	2000	-
Cl.15 of IS 302-2-30:2007 &IS:302-1:2008(Moisture Resistance)	-	4000	-
Cl.19 of IS 302-2-30:2007 &IS:302-1:2008(Abnormal Operation)	-	2000	-
Cl.21 of IS 302-2-30:2007 &IS:302-1:2008(Mechanical Strength)	-	2000	-
Cl.25 of IS 302-2-30:2007 &IS:302-1:2008(Supply Connection and External Flexible Cords )	-	2000	-
Cl.27 of IS 302-2-30:2007 &IS:302-1:2008(Provision for Earthing)	-	2000	-
Cl.30 of IS 302-2-30:2007 &IS:302-1:2008(Resistance to Heat and Fire.)	-	4000	-
Cl.31 of IS 302-2-30:2007 &IS:302-1:2008(Resistance to Rusting)	-	2500	-
Cl.20 of IS 302-2-30:2007 &IS:302-1:2008(Stability & Mechanical Hazards)	-	5000	-
Cl.26 of IS 302-2-30:2007 &IS:302-1:2008(Terminal for External Conductors)	-	2000	-
Cl.28 of IS 302-2-30:2007 &IS:302-1:2008(Screws and Connections)	-	2000	-
Cl.29 of IS 302-2-30:2007 &IS:302-1:2008(Clearances, Creepage Distances and Solid Insulation.)	-	2500	-
Cl.7 of IS 369:2019(Dimensions)	-	5000	-
Cl.9 of IS 369:2019(Temperature rises of surfaces surrounding the heater)	-	3000	-

Complete

-
-

IS 302 : Part 2 : Sec 35 (2017)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 35 electric instantaneous water heaters (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.8(Verification)	-	2500	-
Cl.10(Verification)	-	2500	-
Cl.11(Verification)	-	3000	-
Cl.13(Verification)	-	4000	-
Cl.14(Verification)	-	2000	-
Cl.15(Verification)	-	4000	-
Cl. 16(Verification)	-	4000	-
Cl.19(Verification)	-	4000	-
Cl.22(Verification)	-	2000	-
Cl.25(Verification)	-	2000	-
Cl.26(Verification)	-	2000	-
Cl.27(Verification)	-	2000	-
Cl.28(Verification)	-	2000	-
CL.29(Verification)	-	2500	-
Cl.30(Verification)	-	4000	-
Cl.31(Verification)	-	2500	-

Complete

-
-

IS 302 : Part 2 : Sec 21 (2018)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 21 stationary storage type electric water heaters (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0(Protection against access to live parts)	-	2500	-
10.0(Input and Current)	-	2500	-
11.0(Heating)	-	3000	-
13.0(Leakage Current and electric strength at operating temperature)	-	4000	-
14.0(Transient Overvoltage)	-	2000	-
15.0(Moisture resistance)	-	4000	-
16.0(Leakage current and Electric strength (After Humidity (Environmental) Treatment))	-	4000	-
19.0(Abnormal Operation)	-	2000	50% for Additional Core
21.0(Mechanical Strength)	-	2000	-
25.0(Supply Connection and External Flexible Cords)	-	2000	-
26.0(Terminals for external conductors)	-	2000	-
27.0(Provision For Earthing)	-	2000	-
28.0(Screws and Connections)	-	2000	-
30.0(Resistance To Heat and Fire)	-	4000	-
31.0(Resistance To Rusting)	-	2500	-
29.0(Creepage Distances and Clearances)	-	2500	-
22.0(Construction)	-	2000	-
23.0(Internal Wiring)	-	2000	-
17.0(Overload Protection of transformer and associated circuit)	-	2000	-
20.0(Stability and mechanical hazards)	-	5000	-

Complete

-
-

IS 996 (2009)

Single phase a.c. induction motors for general purpose (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Type of enclosures)	-	10000	-
12.6(Vibration Severity)	-	2000	-
12.1.1(Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-	5000	-
12.5.1(Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-	3000	-
13.1(High voltage test)	-	4000	-
13.2(Moisture proofness)	-	4000	-
13.3(Leakage current test)	-	2000	-
12.7(Insulation resistance test)	-	4000	-
12.2(Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-	2000	-

Complete

-
-

IS 9763 (2000)

Plastics Bib Taps, Pillar Taps, Angle Valves and Stop Valves for Hot and Cold Water Services -

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl. 5)(Nominal Size)	-	300	-
(Cl. 7)(Identification)	-	300	-
(Cl. 7)(Identification)	-	300	-
(Cl.6 , Table 3)(Dimensions)	-	1800	-
(Cl 8)(Construction,Workmanship and Finish)	-	300	-
(Cl 8)(Construction,Workmanship and Finish)	-	300	-
(Cl 8)(Construction,Workmanship and Finish)	-	300	-
(Cl 8.4)(Minimum Thickness)	-	300	-
(Cl. 8.5)(Finish)	-	300	-
(Cl 9.1)(Resistance to Residual Chlorine in Water)	-	500	-
(Cl 9.2)(Drip Proofness Test)	-	1500	-
(Cl 9.3)(Thermal Shock Test )	-	500	-
(Cl 9.4)(Hydraulic Pressure Test)	-	1500	-
(Cl 9.5)(Mechanical Strength Characteristics)	-	1500	-

Complete

-
-

IS 2312 (1967)

Specification for propeller type AC ventilating fans (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Sizes )	-	2000	NA
10.1(Starting )	-	2000	-
14.2 & 15.1(Air Delivery)	-	4500	-
14.3.A(Temperature-Rise (for motors))	-	3000	-
14.1 & 14.6(Power factor)	-	2000	-
14.7(ac leakage)	-	4000	-
14.8(High voltage test)	-	4000	-
14.9(Insulation-Resistance)	-	2000	-
14.1(Earthing continuity)	-	2000	-
14.11 & 15.1(Electrical Input)	-	2500	-
14.12 & 16(Fan Speed)	-	2000	-
13.1(Marking)	-	2000	-
13.1 (a)(Marking)	-	2000	-
13.1 (b)(Marking)	-	2000	-
13.1 (c)(Marking)	-	2000	-
13.1 (d)(Marking)	-	2000	-
13.1 (e)(Marking)	-	2000	-
13.1 (f)(Marking)	-	2000	-
13.1 (h)(Marking)	-	2000	-
13.1 (j)(Marking)	-	2000	-
13.2(Marking)	-	2000	-
13.4(Marking)	-	2000	-
4.1(Rated Voltage)	-	1000	-
5.1(Rated frequency)	-	1000	-
6.1(Design and General Construction)	-	1000	-
6.3(Design and General Construction)	-	1000	-
6.3(Design and General Construction)	-	1000	-
6.4(Design and General Construction)	-	1000	-
6.5(Design and General Construction)	-	1000	-
6.6(Design and General Construction)	-	1000	-
6.7(Design and General Construction)	-	1000	-
6.9(Design and General Construction)	-	1000	-
6.1(Design and General Construction)	-	1000	-
6.11(Design and General Construction)	-	1000	-
6.12(Design and General Construction)	-	1000	-
7.1(Design and General Construction)	-	1000	-
8.1(Design and General Construction)	-	1000	-
9(Design and General Construction)	-	1000	-
11.1(Interchangeability)	-	2000	-
14.3(Temperature-Rise)	-	3000	-
14.3.A(Temperature-Rise (for motors))	-	3000	-
14.3.A(Temperature-Rise (for motors))	-	3000	-
14.3.B(Temperature-Rise (for regulators))	-	3000	-
14.3.B(Temperature-Rise (for regulators))	-	3000	-
14.3.B(Moistureproofness (for regulators only))	-	4000	-

Complete

-
-

IS 4250 (1980)

Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8( Protection Against Electric Shock, IS 302-1)	-	2500	-
9(Starting, IS 302-1)	-	2000	-
10(Power Input and Current, IS 302-1)	-	2500	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	4000	-
15(Moisture Resistance, IS 302-1)	-	4000	-
19(Abnormal Operation, IS 302-1)	-	2000	-
25(Supply Connection and External Flexible Cords, IS 302-1)	-	2000	-
27(Provision for Earthing, IS 302-1)	-	2000	-
20(Stability & Mechanical Hazards, IS 302-1)	-	5000	-
21(Mechanical Strength, IS 302-1)	-	2000	-
Cl.26(Verification)	-	2000	-

Complete

-
-

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

10320 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking, IS 9537-2)	-	520	-
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	2515	Dimensions and Uniformity of thickness
7.4(Screw threads, IS 9537-2)	-	2030	Thread Characteristics
8.2(Construction, IS 9537-2)	-	520	-
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	1790	-
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	1790	-
13(External Influences, IS 9537-2)	-	1155	-

Complete

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

7676 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause -4, 4.1( CARBON)	-	3795	Chemical Composition
Cl 5.1(Workmanship)	-	520	Freedom from defects
Cl 6.1(Diameter)	-	559	Nominal Size
Cl 9.3(Press)	-	1358	Bend Test

Complete

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Upto 4mm

7762 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.1.1(Sulphur)	-	3795	Chemical Composition
Cl 4.1(Workmanship)	-	520	Freedom from defects
Cl 5 & 6(Diameter)	-	559	Nominal Size
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	1444	Reverse bent test

Complete

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

MSME Testing Centre, New Delhi

Shaheed Capt. Gaur Marg, Okhla Phase -III, New Delhi, South East, Delhi, 110020

9582093108 [email protected]

Scope List