BIS - LIMS (Laboratory Information Management System)

CIPET, Hajipur

INDUSTRIAL AREA, HAJIPUR, Vaishali, Bihar, 844102

7781020335 [email protected]

Scope List

Reset

35 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

9725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	250.0	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
5.0 5.1 (Table1) (b)Tolerance on OD)	-	250	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	250	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	250	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
6.0 (6.1) (Visual appearance)	-	300.0	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	3000.0	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1000.0	-
8.0 (8.1) (Supply of pipes )	-	0.0	Charges include in visual Appearance
9.0 (9.1)(Coiling )	-	0.0	Charges include in visual Appearance
9.0 (9.1)(Minimum Internal Diameter of Coil)	-	0.0	Charges include in Dimension
3.1(Class of Pipe)	-	0.0	Charges include in visual Appearance
6.1(Visual Appearance)	-	300.0	-
7.2(Reversion Test)	-	1000	Testing Charges - 700 Specimen Charges - 300 Total Charges - 1000
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0.0	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	0.0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200.0	0.0
7.3(Elongation at Break)	-	1350.0	Testing Charges - 1100 Specimen Charges - 250 Total Charges - 1350 Charges include for tensile test
7.3(Tensile Test)	-	0.0	Charges include in Elongation at Break
4.3(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	700	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	-
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	-
4.1.c.i (Density)	-	1125	Testing Charges - 500 Specimen Charges - 625

Complete

07 Oct, 2022

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

17150.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925.0	-
4.2.3(Carbon Dispersion Test)	-	700.0	-
5(Types and Features )	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	3050.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	3050.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.3(Types and Features )	-	0.0	-
5.6(Types and Features )	-	0.0	-
6.1(Finish)	-	300.0	-
7.1.1(Resistance to Deformation)	-	700.0	-
7.1.2(Resistance to Deformation)	-	700.0	-
7.2(Resistance to Impact)	-	1100.0	-
7.3(Test for Top Load Resistance)	-	900.0	-
7.4(Tensile Strength)	-	1350.0	1100+250(Specimen Charges)
7.5(Flexural Modulus)	-	1600.0	1100+500 (Specimen Charge)
7.6(overall Migration)	-	2200.0	1700+500 (Specimen Charges)
9.2.1(Man-Hole and Hand-Hole Lids)	-	1050.0	-
9.2(Man-Hole and Hand-Hole Lids)	-	0.0	-
9.1(Man-Hole and Hand-Hole Lids)	-	250.0	-
9.1(Lid Thickness)	-	250.0	-
7.3(Test for Top Load Resistance)	-	900.0	-
6.1(Finish)	-	300.0	-
5.4(Wall Thickness above effective height)	-	250.0	-
5.2 Table 2 (7)(Minimum Wall Thickness)	-	250.0	-
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500.0	-

Complete

07 Oct, 2022

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

11475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Marking)	-	300	Including Visual appearance, color Designation)
3(Designation)	-	0.0	Include in Marking
4(Colour)	-	0.0	Include in Marking
6(Dimensions of pipes)	-	250.0	-
7(Visual Appearance)	-	0.0	Include in Marking
8.1(Hydraulic characteristics)	-	6400.0	a) Acceptance Test - 1600 b) Type Test - 4800
8.2(Reversion)	-	700	Testing Charges - 700 Specimen Charges - 300
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1100	-
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	-

Complete

07 Oct, 2022

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

19175 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3(CLASSIFICATION OF PIPES)	-	0	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1100	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	1125	625 + 500
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1100	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
4.3(Anti-oxidant)	-	1100	-
5.1 table -1(DIMENSIONS OF PIPES)	-	500	-
5.1.2(Ovality)	-	0	-
6.1(VISUAL APPEARANCE)	-	300	-
7.1 Table -2(Hydraulic Characteristics)	-	0.0	-
7.2(Reversion Test)	-	1000	700 + 300 (specimen charges)
7.3(Tensile Test)	-	1350	1100 + 250 (specimen charges)
7.4table-2(Fusion Compatibility Test)	-	6400	-
7.5(Density)	-	500	-
7.6(Melt now Rate (MFR))	-	1100	-
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	700	-
(Cl.4.2)(Carbon black- a)carbon content)	-	925	-
Cl.7.4(Fusion Compatibility Test- b) Acceptance test)	-	1600	-
Cl.7.4(Fusion Compatibility Test- a) Quality test)	-	4800	-
Cl.7.3(Tensile Test - ii)Elongation at Break)	-	1350	1100 + 250 (specimen charges)
Cl 7.1(Hydraulic Characteristics - Acceptance test)	-	1600	-
Cl 7.1(Hydraulic Characteristics - Quality test)	-	4800	-
Cl.6(Visual Appearance)	-	300	-
Cl.5(Dimensions of pipe - ii) Wall thickness maximum)	-	0	-
Cl.5(Dimensions of pipe - ii) Wall thickness minimum)	-	0	-
Cl.5(Dimensions of pipe - i) Outside diameter)	-	0	-

Complete

07 Oct, 2022

-
-

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

10675 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
19(Marking)	-	0.0	-
3(Type of Fitting)	-	300.0	Colour of fittings - 300
4(Size Designation)	-	500.0	Test charges includes Wall Thickness, Socket Dimension & Chamfer - 500.0
7.1,Table 1(Wall thickness)	-	500.0	Test charges includes Wall Thickness, Socket Dimension & Chamfer - 500.0
7.2 ,Table 2&3(Socket Dimensions)	-	500.0	Test charges includes Wall Thickness, Socket Dimension & Chamfer - 500.0
7.3(Dimensions of waste trap(Nahani Trap)	-	500.0	Test charges includes Wall Thickness, Socket Dimension & Chamfer - 500.0
8(Sealing Rings)	-	375	Hardness of sealing ring - 375.0
10(Workmanship)	-	300.0	-
11(Design requirements)	-	500.0	Including Design Requirement (Visual) & Access opening (Optional) - 500.0
11.1(Solvent cement type or Rubber ring type)	-	500.0	Including Design Requirement (Visual) & Access opening (Optional) - 500.0
11.2(Socket and spigot configeration)	-	300.0	Visual Appearance
11.4,Table 5(Vent cowl)	-	500.0	-
11.5,Table 6(Pipe Clips)	-	500.0	-
12(Physical test requirements)	-	0.0	-
12.2(Stress relief test)	-	700	-
12.3(Vicat softening tempewrature)	-	1100	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	2500	Testing Charges - 2000 Specimen charges- 500
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1200.0	-
Cl.15, Annex B(Sulphated Ash Content)	-	950	-
16(Mechanical Properties)	-	0.0	-
16.1(Impact test)	-	1100.0	-
17(Watet tightness of joint)	-	850	-

Complete

07 Oct, 2022

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET, Hajipur

INDUSTRIAL AREA, HAJIPUR, Vaishali, Bihar, 844102

7781020335 [email protected]

Scope List