BIS - LIMS (Laboratory Information Management System)

CIPET, Hajipur

INDUSTRIAL AREA, HAJIPUR, Vaishali, Bihar, 844102

7781020335 [email protected]

Scope List

Reset

35 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

15931 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.2(Resistance to External Blows at 0°C)	-	1400.0	Testing Charges- 1100.0 Specimen Charges - 300.0
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850.0	Nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850.0	Nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000.0	Nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850.0	Nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000.0	Nil
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	575.0	Nil
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100.0	Nil
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900.0	Testing Charges - 700.0 Specimen Charges - 200.0
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575.0	Nil
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300.0	Nil
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300.0	Nil
9.1(PIPE ENDS)	-	0.0	Testing Charges included in Visual Appearance
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500.0	Dimension Charges (All)
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0.0	Dimension Charges (All)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0.0	Dimension Charges (All)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0.0	Dimension Charges (All)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0.0	Dimension Charges (All)
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0.0	Dimension Charges (All)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0.0	Dimension Charges (All)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0.0	Dimension Charges (All)
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0.0	Dimension Charges (All)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0.0	Dimension Charges (All)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0.0	Dimension Charges (All)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0.0	Dimension Charges (All)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0.0	Dimension Charges (All)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0.0	Dimension Charges (All)
7(DIMENSIONS-PIPE-Nominal Diameter)	-	0.0	Dimension Charges (All)
Clause 10.7(Sulphated Ash Content)	-	950.0	Nil
5(CLASSIFICATION OF PIPES)	-	0.0	Charges included in Visual Appearance
10.3(Effect on Water)	-	3000	-

Complete

07 Oct, 2022

-
-

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

38725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1 (Visual and Workmanship Requirement)	-	300	-
6.2, 6.2.1 (Quick Coupled Fittings)	-	6750.0	Density : 1000 (5002) Melt Flow Rate: 2200 (11002) Carbon Black Content: 1850 (9252) Carbon Black Dispersion:1400 (7002) Workmanship & Appearance: 300
6.1.3.2 (Quick coupled fittings)	-	0.0	-
6.1.3.1.1(Weldability Test)	-	6400.0	Acceptance Test: 1600 Quality Test: 4800
6.1.3, 6.1.3.1(Weldability Test)	-	0.0	-
6.1.2.2( Hydraulic Proof Test)	-	850.0	-
6.1.2, 6.1.2.1( Hydraulic Proof Test)	-	850.0	-
6.1(Quick Coupled Pipes and Fittings)	-	0.0	-
5.3(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	500.0	-
5.2(Dimensions of Quick Coupled Pump Connectors Table 3.)	-	0.0	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	0.0	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	0.0	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	0.0	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	0.0	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	0.0	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	0.0	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	0.0	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.1.5(Rubber Ring)	-	4950.0	Hardness before Ageing: 375.0 Ageing : 4200.0 Hardness after Ageing: 375.0
4.1.4(b)(Holding Attachments for Coupler Parts)	-	0.0	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	0.0	-
4.1 .3(Workmanship and Appearance)	-	300.0	-
4.1 .1.2.2(HDPE couplers)	-	0.0	-
4.1 .1.2.1(HDPE couplers)	-	0.0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700.0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
4.1 (b)(HDPE couplers —)	-	0.0	-
4.1 (a)( Quick Coupled Male and Female Couplers)	-	0.0	-
4(QUICK COUPLED FITTINGS)	-	0.0	-
3(QUICK COUPLED PIPES)	-	17575.0	-
Cl.6.1.3(Weldability Test- b) Acceptance test)	-	1600	-
Cl.6.1.3(Weldability Test- a) Quality test)	-	4800	-
Cl 4.1.5(Rubber rings- C)Rubber ring shall be of black colour:)	-	300.0	-
Cl 4.1.5(Rubber rings- B) Change in hardness)	-	375	-
Cl 4.1.4(Holding attachments for coupler parts)	-	1700.0	850+850
Cl.4.1.3(Workmanship and appearance )	-	300.0	-
Cl.4.1(Quick Coupled Male and Female Couplers)	-	0.0	-
Strength requiement for Seat Cl9.1(The seat shall withstand the load of 1150 N for 30 minutes without permanent distortion of the seat or the hinge fittings or damage to any finish.)	-	0.0	-

Complete

07 Oct, 2022

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

10625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	NA
9.5(Tensile Strength IS 12235(Part 13))	-	1600	1100 - Testing Charges 500 - Specimen Charges
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1300	Testing Charges - 1000.0 Specimen Charges - 300.0
9.3(Density IS 12235 (Part 14))	-	500	Nil
9.2(Internal Diameter)	-	250	Nil
9.1( Visual Appearance)	-	300	Nil
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1750	Testing Charges - 1000.0 Specimen Charges/ Conditioning Charges - 500 Dimension of thread for Screen & casing pipes - 250
8.4(Sealing rings - Hardness)	-	375	Nil
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	250.0	Nil
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	0	Charges included in dimension
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	0.0	Charges included in dimension
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	0.0	Charges included in dimension
7.4 Table 8 & 9 Fig 1(Segmental length, l5)	-	0.0	Charges included in dimension
7.4 Table 8 & 9 Fig 1(Segmental length, l4)	-	0.0	Charges included in dimension
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0.0	Charges included in dimension
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	0.0	Charges included in dimension
7.3.2(Rib height)	-	0.0	Charges included in dimension
7.3.1(No.of Ribs)	-	0.0	Charges included in dimension
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0.0	Charges included in dimension
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0.0	Charges included in dimension
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	0.0	Charges included in dimension
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0.0	Charges included in dimension
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0.0	Charges included in dimension
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0.0	Charges included in dimension
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	0.0	Charges included in dimension
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0.0	Charges included in dimension
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0.0	Charges included in dimension
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0.0	Charges included in dimension
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0.0	Charges included in dimension
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	0.0	nil
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	0.0	nil
5(COLOUR)	-	0.0	Charges included in Visual Appearance
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000	-

Complete

07 Oct, 2022

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

31869.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Slow Crack Growth Rate)	-	6000.0	Testing Charges - 5500.0 Specimen Charges - 500.0
8.9 table-6(Elongation at Break)	-	1600.0	Testing Charges - 1100.0 Specimen Charges - 500.0
8.8(Tensile Strength for Butt-fusion)	-	1600.0	Testing Charges - 1100.0 Specimen Charges - 500.0
8.7(Density)	-	500.0	Nil
8.5 (Oxidation Induction Time)	-	2200.0	Nil
8.4( Melt Flow Rate)	-	1100.0	Nil
8.2(Longitudinal Reversion Test)	-	900.0	Testing Charges - 700.0 Specimen Charges - 200.0
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600.0	Nil
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400.0	Nil
7.4.1.2(Ovality)	-	0.0	Charges included in Dimension Test
7.4 table -3 & 4(6.1 Dimensions)	-	500.0	Dimension of Pipe (MOD, Ovality, Thickness, Length)
7.2(Length)	-	0.0	Charges included in Dimension
6.2.1(6.1.1 Identification Stripes)	-	250.0	Nil
6.2(Colour)	-	250.0	Nil
8.6(Overall migration)	-	2000.0	Testing Charges - 1700.0 Specimen Charges - 300.0
8.3(Carbon black)	-	1625.0	CBC - 925 CBD - 700

Complete

07 Oct, 2022

-
-

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

9250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0 (chem)(MATERIAL)	-	1050	-
4.1 (chem)(Workmanship and Finish)	-	300	-
4.2 (chem)(Design, Shape & Dimension)	-	300	-
4.3(Workmanship, Finish & Appearance)	-	300	-
4.4 , clause 5 of IS:2798:1998(Brimful capacity in ml)	-	250	-
4.5, IS:2798:1998(Wall thickness- Bottom, in mm)	-	300	-
4.5, IS:2798:1998(Wall thickness- Middle , in mm)	-	300	-
4.5, IS:2798:1998(Wall thickness- Top , in mm )	-	300	-
4.6.2(TRANSPARANCY)	-	700	-
4.6.3(LEAKAGE TEST)	-	1000	-
4.6.4(DROP TEST)	-	1100	-
4.6.5(MIGRATION TEST)	-	1700	-
4.6.6(PORTABILITY TEST)	-	2900	-
4.6.6 (chem)(Water Potability test (after 30 days) (a) Taste (b) Odour)	-	2900	-
4.6.5.1 (chem)(Colour migration (Caps))	-	1700	-
4.6.5.1 (chem)(Colour migration (Container))	-	1700	-
4.6.5 , IS:9845:1998 (chem)(Migration of Caps - a. Amount of extractive)	-	1700	-
4.6.5 , IS:9845:1998 (chem)(Migration- b. Amount of extractive)	-	1700	-
4.6.5 , IS:9845:1998 (chem)(Migration- a. Amount of extractive)	-	1700	-
4.6.3, clause 6 of IS:2798:1998(Leakage test- c. Air pressure leakage)	-	0.0	-
4.6.3, clause 6 of IS:2798:1998(Leakage test- b. Vibration leakage)	-	1000	-
4.6.3, clause 6 of IS:2798:1998(Leakage test- a. Closure leakage )	-	0.0	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

9025.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	4100.0	VCM Content - 3000 K-Value - 1100
4(Size of fitting)	-	0.0	Charges include in Dimension
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500.0	-
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0.00	Charges include in dimension of socket
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0.0	Charges include in dimension of socket
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	0.0	Charges include in dimension of socket
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	575	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	850.0	-
8(Marking)	-	0.0	-
15.4 (b)(Cold impact)	-	1100.0	-
9.1(PIPE ENDS)	-	0.0	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	3000	Total Charges for effect on water
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	3000.0	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	3000	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	3000	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Mercury (all three extracts))	-	3000	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-10)(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction))	-	3000	3000
10.7 of IS 4985(Sulphated Ash content, Annex-B of IS 4985)	-	0	-
3.2.1, Table-1, Fig-1(Nominal size)	-	0.0	-
3.2.1, Table-1, Fig-1(B)	-	0.0	-
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	0	-
3.2.1, Table-1, Fig-1(Plumbing)	-	0	-
Clause 3.2.2, and Fig. 2(Nominal size)	-	0	-
Clause 3.2.2, and Fig. 2.(B)	-	0	-
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	0	-
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	0	-
3.1(General)	-	1925	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2, 3.2.1, Fig 1(Manufacture)	-	0.0	-
3.2.2, Fig 1(Dimensions)	-	500	-
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2, 3.2.1, Fig 1(Manufacture)	-	0.0	-
3.2.2, Fig 1(Dimensions)	-	500	-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2, 3.2.1, Fig 1(Manufacture)	-	0.0	-
3.2.2, Fig 1(Dimensions)	-	500	-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Equal Tees)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2, 3.2.1, Fig 1(Manufacture)	-	0	-
3.2.2, Fig 2, table 2(Dimensions)	-	500	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500	-
Table 2 (Cl.3.2.2, and Fig.1)(Dimensions of Flanged Tail Piece with Metallic Flange for Elastomeric Sealing Ring Joint)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

9025 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2(Materials)	-	4100	-
3.3, 3.3.1, Fig 1(Manufacture)	-	0.0	-
3.3.2, table 1, fig 1(Dimensions)	-	500	-
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	500	-
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2, 3.2.1, Fig 2(Manufacture)	-	0	-
3.2.2, Fig 2, table 2(Dimensions)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	500	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2, 3.2.1, Fig 2(Manufacture)	-	0	-
3.2.2, Fig 1, table 1(Dimensions)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	-
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	500	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2, 3.2.1, Fig 2(Manufacture)	-	0	-
3.2.2, Fig 1, table 1(Dimensions)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 45o Bend)	-	500	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	500	-
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	500	-

Complete

07 Oct, 2022

-
-

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4425	-
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	500	-
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	500	-
3.2.3(Socket, Measurement)	-	500	-

Complete

07 Oct, 2022

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

16000.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	300.0	-
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100.0	-
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500.0	-
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0.0	-
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0.0	-
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0.0	-
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0.0	-
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0.0	-
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	300.0	-
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1000.0	700+300 (Specimen Charges)
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700.0	-
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100.0	-
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	4350.0	1100+250 3500 (UV Exposure)-Natural 21800 (Weatherometer Xenon arc for 116 hrs) - Optional
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500.0	2000+500 (Specimen Charges)
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1400.0	1100+300 (Specimen Charges)
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1350.0	1100+250 (Specimen Charges)
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	700.0	-
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	500.0	-
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	1000.0	-

Complete

07 Oct, 2022

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

19380 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material Identification)	-	1050	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1100	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	850	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	900	-
3.2(Unlaminated Fabric Mass )	-	250	-
3.3.1(Bottom seam (IS 10789))	-	250	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	250	-
4.2 and Table 1 ii(Dimensions )	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
4.2 and Table 1 v(Mass of sack )	-	250	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	2200	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	-
4.2 and Table 1 x(Ash content )	-	950	-

Complete

07 Oct, 2022

-
-

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

19140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	1050	-
3.2(Tapes – Width )	-	250	-
3.2(Tapes – Linear Density )	-	0.0	-
3.3(Tying Cord)	-	0.0	-
3.4(Sack)	-	0.0	-
3.4.1(Seam)	-	250	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	250	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	250	-
4.1 and Table 1 ii(Ends per dm )	-	250	-
4.1 and Table 1 iii(Picks per dm )	-	250	-
4.2 and Table 1 iv(Mass of sack )	-	300	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	1100	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	1100	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	1100	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	1100	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12540	-
4.1 and Table 1 ix(Ash content )	-	950	-

Complete

07 Oct, 2022

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

19480 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	-
4.1(Raw Material)	-	1050	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	-
4.2(Tapes – Linear Density )	-	500	-
4.2(Construction)	-	0	-
4.3.1(Bottom Seam)	-	250	-
4.3.1( The two rows of stitches shall be separated from each other)	-	250	-
4.3.1( The outer stitch)	-	250	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	250	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	250	-
4.3.1(The number of stitches/dm)	-	250	-
4.3.2(Mouth)	-	250	-
4.4 and Table 1 i(Capacity)	-	250	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
5.1 and Table 1 v(Mass of sack )	-	250	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	1100	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	1100	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	-
5.2 and Table 1 x(Ash content )	-	950	-

Complete

07 Oct, 2022

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	300	-
5.1.2(Film Form)	-	300	-
5.1.3(Odour)	-	300	-
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	500	-
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	-
5.1.6a(Carbon Black Content, Annex-A)	-	925	-
5.1.6b(Ash Content, Annex-A)	-	950	-
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	-
5.2.2(Tolerance on Thickness, Annex-A)	-	250	-
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1100	-
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1100	-
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	-
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	1100	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	1100	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1100	-
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1000	-
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1000	-
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1100	-
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1100	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	1100	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	1100	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	1100	-
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tear resistance , Annex B)	-	2000	1500+500
8.1, Table 3(Puncture resistance , Annex C)	-	1350	1100+250
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tear resistance , Annex B)	-	2000	1500+500
9.1, Table 4(Puncture resistance , Annex C)	-	1350	1100+250
Clause 9.1 (Table 4)(Break Elongation)	-	1100	-
Clause 9.1 (Table 4)(Yield Elonation)	-	1100	-
Clause 9.1 (Table 4)(Break strength)	-	1100	-
Clause 9.1 (Table 4)(Yield strength)	-	1100	-
Clause 8.1(Table 3)(Break Elongation)	-	1100	-
Clause 8.1(Table 3)(Break strength)	-	1100	-
Clause 7.1(Table 2)(Dart Impact Strength)	-	1100	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1100	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1100	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1100	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1100	-
Clause 5.2.3(Tolerance on Width)	-	250	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	500	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	500	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	500	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	500	-
Cl. 6.1(Stress Relief Test- Appendix A)	-	700	-
Cl. 6.2(Opacity- Appendix B)	-	575	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	3000	-
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	3000	-
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	3000	-
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	3000	-
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	850	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	500	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	3000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	3000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	3000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	3000	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5625	-
2.2(Manufacture)	-	0	-
2.2.2(diameter of the socket of cap)	-	500	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5625	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	500	-
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	500	-
2.2.3( inside diameter of the socket)	-	500	-
2.2.3(socket length)	-	500	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5625	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	500	-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	500	-
2.2.3( inside diameter of the socket)	-	500	-
2.2.3(Socket length)	-	500	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5625	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	500	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	500	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	500	-
2.2.3( inside diameter of the socket)	-	500	-
2.2.3(Socket length)	-	500	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5625	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	500	-
2.2.2, Table 1(Socket Laying Length)	-	500	-
2.2.3( inside diameter of the socket)	-	500	-
2.2.3(Socket length)	-	500	-

Complete

07 Oct, 2022

-
-

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

8625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5625	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	500	-
2.2.2, Table 1(Union Laying Length)	-	500	-
2.2.3( inside diameter of the socket)	-	500	-
2.2.3(Socket length)	-	500	-

Complete

07 Oct, 2022

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET, Hajipur

INDUSTRIAL AREA, HAJIPUR, Vaishali, Bihar, 844102

7781020335 [email protected]

Scope List