BIS - LIMS (Laboratory Information Management System)

National Test House (NR)

Kamla Nehru Nagar,Ghaziabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

9999472699 [email protected]

Scope List

Reset

44 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

Type-Calcareous Fly Ash / Siliceous Fly Ash

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	2000	-
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	1000	-
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	2000	-
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	1000	-
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	1000	-
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	1000	-
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	1000	-
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	1000	-
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	1000	-
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	1000	-
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	1000	-
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	3000	-
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	3000	-
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	1500	-

Complete

-
-

IS 10631 (1983)

Specification for stainless steel for welding electrode core wire

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table 1(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
5.1 Table 1(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
5.1 Table 1(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
5.1 Table 1(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
5.1 Table 1(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
5.1 Table 1(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
5.1 Table 1(Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
5.1 Table 1(Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(FREEDOM FROM DEFECTS)	-	1000	-
7(Size and Tolerances)	-	1000	-

Complete

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(MATERIALS : ARMGURING)	-	3000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
16.5(Oxygen Index Test)	-	1000	-
16.1(Temperature Index)	-	1000	-
16.9(Test for Halogen Acid Gas Evolution)	-	1000	-

Complete

-
-

IS 303 (1989)

Plywood for General Purposes -

Grade BWR/Type AA/AB/BB

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	750	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	750	-
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	1500	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	3000	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	3000	-
11.3(Moisture Content - Part 1 of IS 1734)	-	1000	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	500	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	0	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	0	-
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	1000	-
5.1(Type - For BB Type)	-	0	-
5.1(Type - For AB Type)	-	0	-
5.1(Type - For AA Type)	-	0	-
4(Grade - For MR grade)	-	0	-
4(Grade - For BWR grade)	-	0	-

Complete

-
-

IS 2202 : Part 1 (1999)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

Grade-BWP /Type-BD,BN,PD,PN,MD,MN

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(Workmanship & finish - IS 2202(Pt-1))	-	0	-
9.2(Workmanship & finish - IS 2202(Pt-1))	-	0	-
9.3(Workmanship & finish - IS 2202(Pt-1))	-	0	-
11.1(Height - IS 4020 (Pt-2))	-	500	-
11.1(Width- IS 4020 (Pt-2))	-	500	-
11.1(Thickness - IS 4020 (Pt-2))	-	500	-
11.1(Variation in thickness - IS 4020 (Pt-2))	-	0	-
11.1( Squareness Test - IS 4020 (Pt-2))	-	500	-
11.2( Twist, cupping & wrapping - IS 4020 (Pt-3))	-	1000	-
11.3(Depth of deviation - IS 4020(Pt-4))	-	1000	-
11.4(Impact Indentation Test - IS 4020(Pt-5))	-	1000	-
11.4(Depth of indentation - IS 4020(Pt-5))	-	0	-
11.5(Deflection at maximum load - IS 4020(Pt-6))	-	1000	-
11.5(Residual deflection - IS 4020(Pt-6))	-	0	-
11.6(Deflection of the edge at maximum load - IS 4020(Pt-7))	-	750	-
11.6(Residual deflection after removal of load - IS 4020(Pt-7))	-	0	-
11.6(Lateral buckling during loading - IS 4020(Pt-7))	-	750	-
11.6(Residual lateral buckling - IS 4020(Pt-7))	-	0	-
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	750	-
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	750	-
11.8(Buckling Test - IS 4020(Pt-9))	-	1500	-
11.8(Initial deflection - IS 4020(Pt-9))	-	0	-
11.8(Residual deformation after 15 minutes of unloading - IS 4020(Pt-9))	-	0	-
11.9(Slamming Test - IS 4020(Pt-10))	-	1000	-
11.1(Misuse Test - IS 4020(Pt-11))	-	1000	-
11.11(Varying Humidity Test - IS 4020(Pt-12))	-	1000	-
11.11(The recovery of the original size after subjecting the door to high and low humidity- IS 4020(Pt-12))	-	1000	-
11.11(Maximum departure from the general planeness - IS 4020(Pt-12))	-	1000	-
11.12(End Immersion Test - IS 4020(Pt-13))	-	1000	-
11.13(Knife Test - IS 4020(Pt-14))	-	1000	-
11.14(Glue Adhesion Test - IS 4020(Pt-15))	-	1000	-
11.15(Screw Withdrawal Resistance test - IS 4020 (Pt-16))	-	1000	-
11.15(Screw Withdrawal Strength - IS 4020 (Pt-16))	-	0	-

Complete

-
-

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

GRADE-BWP,MR/TYPE-DEC,COM

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.3(Dimensional Requirements - Length - 8.1.4)	-	1000	-
7.3(Dimensional Requirements - Width - 8.1.4)	-	0	-
7.3(Dimensional Requirements - Thickness - Annexure E)	-	0	-
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	0	-
7.3(Dimensional Requirements - Squareness - Annexure D)	-	0	-
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	0	-
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	1000	-
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	0	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	1000	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	1000	-
9.2.3(Adhesion of Plies - Annexure H)	-	1000	-
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	2000	-
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	0	-
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	1000	-
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	0	-
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	1000	-
9.2.6(Spot test - Annexure L)	-	2000	-

Complete

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

27000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	1000	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	0	-
Cl 7.2(Weight)	-	1000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	-
Cl. 8.1 Table 3(TS/YS ratio)	-	0	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	1000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	1000	-
Cl 5(Deformations and Surface Characteristics)	-	15000	-
4.1(Sulphur and phosphorous)	-	500	-
4.1(CE)	-	1000	-
4.1( Nitrogen%)	-	500	-
4.1(Ni)	-	500	-
4.1(Mo)	-	500	-
4.1(Cr)	-	500	-
4.1( Ti)	-	500	-
4.1(V)	-	500	-
4.1( Copper %)	-	500	-
4.1(Silicon %)	-	500	-
4.1(Sulphur %)	-	500	-
4.1(Phosphorus %)	-	500	-
4.1(Manganese %)	-	500	-
4.1(Carbon %)	-	500	-
4.1( Aluminium %)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	500	-

Complete

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.8(Smoke density rating)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
10.6(Halogen evolution)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
10.7(Temperature index)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
10.5(Oxygen index)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
11.1(Durability)	-	100	-
11(Identification)	-	100	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	2000	-
table 1 e) 3) (IR constant- max. Temp)	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
table 1 e) 3) (IR constant- Room temp )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
table 1 e) 3) (Volume Resistivity - Room temp )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
10.2(HV (room temperature))	-	1000	RUPEE 100 EXTRA FOR EACH OTHER CORE
10.1(HV (water immersion))	-	1500	RUPEE 150 EXTRA FOR EACH OTHER CORE
10.1(HV (water immersion))	-	1500	RUPEE 150 EXTRA FOR EACH OTHER CORE
10.4(Flammability test- Unaffected portion)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
10.4(Flammability test-Burning after flame removal)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1(Category Code)	-	100	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 4)(Cracks Observed)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	750	RUPEE 75 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	750	RUPEE 75 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- TS variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(Elongation variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(TS variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(Elongation (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 1)(Elongation (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	10	-
8.3(Thickness of Sheath)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
5.2(Application )	-	100	-
5.3(Thickness of Insulation)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
9.1(Ovality)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
9(Overall dimensions)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
4.2(Conductor resistance test)	-	1500	RUPEE 150 EXTRA FOR EACH OTHER CORE
4.1(Wrapping test (for Al))	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
4.1(Tensile test (for Al)- After Stranding)	-	1000	RUPEE 100 EXTRA FOR EACH OTHER CORE
4.1(Tensile test (for Al)-Before Stranding)	-	300	RUPEE 30 EXTRA FOR EACH OTHER CORE
4.1(Annealing test (for copper))	-	1000	RUPEE 100 EXTRA FOR EACH OTHER CORE
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	100	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	100	-
12(CONSTRUCTION Core Identification)	-	100	-
8.1(Sheath Material )	-	100	-
7(Binder Tape)	-	100	-
6.2(Filler)	-	100	-
5.1(Insulation)	-	100	-
4.4(Joints in Conductor)	-	100	-
4.4(Joints in Conductor)	-	100	-
4.1(Conductor - Material)	-	100	-
4.1(Conductor - Material)	-	100	-
10.11(Persulphate Test )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
12.0(Core identification)	-	100	-
4, IS 8130(Construction of conductor)	-	100	-
Table 2, IS 8130(No fo wire in a conductor)	-	100	-
8.3(Minimum thickness of Sheath)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
8.3(Avarage thickness of Sheath)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
5.3(Minimum thickness of insulation)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
5.3(Avarage thickness of insulation)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
Table 4(Copper purity test)	-	500	-
10.3(Spark test)	-	0	-
table 1, 4.2(insulation resistance test)	-	100	RUPEE 10 EXTRA FOR EACH OTHER CORE
5.4(Mechanical properties before and after ageing)	-	100	RUPEE 10 EXTRA FOR EACH OTHER CORE
10.11(Per sulphate test (for tinned Cu cable only))	-	100	RUPEE 10 EXTRA FOR EACH OTHER CORE

Complete

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

8292 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 15(Length, Width & Thickness)	-	1000	-
Cl 18(Weight)	-	1000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	1000	-
Cl 11.3(Press)	-	1000	-
Cl 7(Workmanship)	-	1000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	1000	-
Cl 12(Sudden Load Applied)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	500	-

Complete

-
-

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

33,43,53,43S,53S

10000 View breakup
Rs.10000/- [Rs.6000/- for physical, Rs.4000/- for chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iii a(Setting Time Initial)	-	500	-
7 Table-3 iii b(Setting Time Final)	-	500	-
7 Table-3 i.(Fineness)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	500	-
7 Table-3 ii a(Expansion after aeration)	-	0	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii b(Expansion after aeration)	-	0	-
6.1 Table-2 viii(Alkali content)	-	1000	-
6.1 Table-2 vii(Chloride content)	-	1000	-
6.1 Table-2 vi(Loss on ignition)	-	1000	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	1000	-
6.1 Table-2 iv(Magnesia)	-	1000	-
6.1 Table-2 iii.(Insoluble residue)	-	1000	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	2000	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	3000	-
6 - Table - 1 viii(Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	2000	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	3000	-
6.1 Table-2 viii(Alkali content)	-	1000	-
6.1 Table-2 vii(Chloride content)	-	1000	-
6.1 Table-2 vi(Loss on ignition)	-	1000	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	1000	-
6.1 Table-2 iv(Magnesia)	-	1000	-
6.1 Table-2 iii.(Insoluble residue)	-	1000	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	2000	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	3000	-
6 - Table - 1 viii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	2000	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	3000	-

Complete

-
-

IS 455 (2015)

Portland slag cement - Specification

PSC

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7 Table-2(Cl. 7 Table-2 i (Fineness ))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 ii a (Soundness , Le Chatelier Expansion ))	-	500	-
Cl. 7 Table-2(Cl. 7 Table-2 ii a (Expansion after aeration ))	-	0	-
Cl. 7 Table-2(Cl. 7 Table-2 ii b (Soundness , Autoclave Expansion ))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 ii b (Expansion after aeration ))	-	0	-
Cl. 7 Table-2(Cl. 7 Table-2 iii a (Setting time Initial))	-	500	-
Cl. 7 Table-2(Cl. 7 Table-2 iii b (Setting time Final))	-	500	-
Cl. 7 Table-2(Cl. 7 Table-2 iv a (Compressive Strength 72±1 hr IS))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 iv b (Compressive Strength 168±2 hr ))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 iv c (Compressive Strength 672±4 hr) )	-	1000	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	1000	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	1000	-

Complete

-
-

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

PPC(FAB)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	0	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-

Complete

-
-

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

- View breakup
For BIS samples: Rs.8410/-, For others: Rs.11000/- [Rs.6000/- for physical, Rs.5000/- for chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
Water for construction purposes

IS 1475 : Part 1 (2001)

Self - Contained drinking water coolers - Specification: Part 1 energy consumption and performance (Third Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.2(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.3(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.4(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.5(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.6(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.7(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.8(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.9(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.1(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.11(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.12(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.13(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.14(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.15(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.16(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.17(COMPONENTS AND THEIR MATERIALS)	-	500	-
7.7.1(Insulation Resistance)	-	3000	-
7.7.2(High Voltage Test)	-	3000	-
7.7.3(Cooling capacity rating test)	-	4000	-
7.7.4(Maximum operating conditions)	-	10000	-
7.8.2(Performance test)	-	1500	-

Complete

-
-

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

Type - Powder form/ Liquid form

10000 View breakup
Rs.9000/- [ Rs.8000/-for Mechanical, Rs.1000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	3000	-
Cl 3.2(Initial & Final)	-	500	-
Cl 3.2(Initial & Final)	-	500	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	2000	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	2000	-
Clause 3.4(Chloride content)	-	1000	-
Clause 3.4(Chloride content)	-	1000	-

Complete

-
-

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 & 8.2(Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	carbon content
6 & 8.2(Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Silicon content
6 & 8.2(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Phosphorus content
6 & 8.2(Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Manganese content
6 & 8.2(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Sulphur content
7.1.1(Diameter of Core Wire)	-	500	Dimension
7.1.2(Length of Electrodes)	-	500	Dimension
7.2.1(Contact End)	-	500	Dimension
7.2.2(Arc striking End)	-	500	Dimension
7.3(Concentricity of Flux covering with core wire)	-	500	Dimension
7.4(Defects of Core wire and Coverings)	-	500	Dimension
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-	3000	Strength Parameter
9.1.2 Table 6 ( Yield Stress -Annex F)	-	1000	Strength Parameter
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-	1000	Strength Parameter
9.1.3 Table 6 ( Impact Strength-Annex F)	-	3000	Strength Parameter
9.2(Butt Weld Bend Test-IS 1599)	-	3000	Strength Parameter
9.6(Radiographic Test- IS 1182)	-	1000	NDT Test
9.3(Running PerformanceTest-Annex H)	-	2000	Running Performance Test
9.4(Increased Metal Recovery Test-IS 13043)	-	3000	Increased Metal Recovery Test
9.5(Diffusible Hydrogen Evaluation Test-IS 11802)	-	5000	Diffusible Hydrogen Evaluation Test
6 & 8.2(Copper- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Titanium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Alumiminium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Cr+Ni+Mo - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	1000	-
6 & 8.2(Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	2000	-

Complete

-
-

IS 3097 (2006)

Veneered Particle Boards -Specification

- View breakup
Rs.11000/- [ Rs.11000/-for Mechanical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

Insulating Mats for Electrical Purposes

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	0	-
10.a)(Packing)	-	0	-
10.b)(Packing)	-	0	-
10.c)(Packing)	-	0	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	0	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	0	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	0	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	0	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	500	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	0	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	0	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	1500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	4000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4500	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	4000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	2500	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	7000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Thermal Properties (Cl..8.4))	-	4000	-
8(Extreme Low Temperature (Cl.8.6))	-	6000	-

Complete

-
-

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Dimension and Tolerances)	-	1000	-
9.1 Table-2(Tensile Strength)	-	1000	-
9.1 Table-2(Elongation)	-	1000	-
9.2(Vickers Hardness)	-	1000	-
5.0(Freedom from defects)	-	1000	-
8.1 Table 1(Cu)	-	500	-
8.1 Table 1(Zn)	-	500	-
8.1 Table 1(Pb)	-	500	-
8.1 Table 1(Fe)	-	500	-
8.1 Table 1(Total other impurities excluding iron)	-	500	-

Complete

-
-

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table-1(Sizes Diameter of Line wire)	-	200	-
5 Table-1(Sizes Diamater of Point wire)	-	200	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	200	-
5 Table-1(Sizes Distance between two barbs)	-	200	-
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	200	-
9.1(Freedom from defects)	-	1000	-
12.1(Tensile Strength)	-	2000	-
12.3(Ductility)	-	1000	-
12.2.1(Mass of zinc coating (line wire))	-	500	-
12.2.2(Mass of zinc coating (point wire))	-	500	-
12.2(Uniformity of zinc coating)	-	1000	-

Complete

-
-

IS 710 (2010)

Marine plywood - Specification (Second Revision)

BWP Grade

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(WORKMANSHIP AND FINISH )	-	250	-
7.2(WORKMANSHIP AND FINISH )	-	250	-
7.3(WORKMANSHIP AND FINISH )	-	250	-
7.5(WORKMANSHIP AND FINISH )	-	250	-
6.1(DIMENSIONS)	-	250	-
6.1(DIMENSIONS)	-	250	-
6.2(DIMENSIONS)	-	250	-
6.3(DIMENSIONS)	-	125	-
6.3(DIMENSIONS)	-	125	-
9.1.1(MOISTURE CONTENT)	-	1000	-
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	2000	-
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	0	-
9.1.3 , 9.1.3.1.1(Water resistance test)	-	2500	-
9.1.3 , 9.1.3.1.2(Water resistance test)	-	0	-
9.1.5(Mycological test)	-	2500	-
9.1.5 , 9.1.3.1.1(Mycological test)	-	0	-
9.1.5 , 9.1.3.1.2(Mycological test)	-	0	-
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Individual))	-	0	-
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Average ))	-	0	-
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test) , 9.1.3.1.1 (Glue Shear Strength: Individual))	-	0	-
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test ), 9.1.3.1.1 (Glue Shear Strength: Average))	-	0	-
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 (Glue Shear Strength: Individual))	-	0	-
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-	0	-
9.1.4(Tensile strength)	-	2500	-
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-	0	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-	0	-
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	0	-
9.1.6 (Table 3)(Static bending strength)	-	1500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	0	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	0	-
9.1.6 (Table 3)(Static bending strength)	-	1500	-
Cl. 9.1.6 (Table 3)(Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	0	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	0	-
9.1.7 (Table 4)(Wet bending strength)	-	1500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-	0	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-	0	-
Cl. 9.1.7 (Table 4)(Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-	0	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-	0	-
9.1.7 (Table 4)(Wet bending strength)	-	1500	-
9.1.8(Retention of preservative)	-	3000	-

Complete

-
-

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

BWP/Type1/Type2/Type3/CS/CSC/CSFF

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Types)	-	0	-
7.2(DIMENSIONS & TOLERANCES )	-	250	-
7.2(DIMENSIONS & TOLERANCES )	-	250	-
7.3(DIMENSIONS & TOLERANCES )	-	250	-
7.4(DIMENSIONS & TOLERANCES )	-	125	-
7.4(DIMENSIONS & TOLERANCES )	-	125	-
8.1(WORKMANSHIP AND FINISH )	-	500	-
8.3(WORKMANSHIP AND FINISH )	-	500	-
10.1.1(MOISTURE CONTENT)	-	1000	-
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	0	-
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	2000	-
10.1.2, 10.1.2.2(GLUE ADHESION IN DRY STATE)	-	0	-
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	0	-
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	2500	-
10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST)	-	0	-
10.1.5(MYCOLOGICAL TEST )	-	2500	-
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	0	-
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	0	-
10.1.5.2(MYCOLOGICAL TEST )	-	0	-
10.1.6(TENSILE STRENGTH)	-	0	-
Cl. 10.1.6(Cl. 10.1.6 (Tensile Strength: Parallel to grain))	-	0	0
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Perpendicular to grain))	-	0	-
Cl. 10.1.6(Cl. 10.1.6 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	2500	-
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	0	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Average))	-	1500	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Average))	-	0	-
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	0	-
Cl. 10.1.7 (Table 2)(Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Average))	-	1500	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Average))	-	0	-
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	0	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	1500	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	0	-
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	0	-
Cl. 10.1.8 (Table 3)(Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	0	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	0	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	1500	-
10.1.9(RETENTION OF PRESERVATIVE)	-	3000	-

Complete

-
-

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

Class-Gen purp./Heavy dut Type-Plain (Cement/Coloured )

7000 View breakup
Rs.7000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	500	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	0	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	0	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	0	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	0	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	0	-
Cl 11(Suface Finish)	-	0	-
Cl 12.2(Concavity & Convexity )	-	500	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	500	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	500	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	2000	-
Cl 12.7(Resistance to wear)	-	0	-
Cl 12.7(Resistance to wear)	-	2500	-
Cl 12.7(Resistance to wear)	-	0	-
Cl 12.7(Resistance to wear)	-	2500	-

Complete

-
-

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

5000 View breakup
For BIS samples:Rs.7778.50, for others: Rs.9500/- Full Test, [Rs.5500/- Physical test, Rs.4000/- Chemical test

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Copper %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(V)	-	500	-
6.1( Ti)	-	500	-
6.1(Cr)	-	500	-
6.1(Mo)	-	500	-
6.1(Ni)	-	500	-
6.1( Nitrogen%)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Copper %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(V)	-	500	-
6.1( Ti)	-	500	-
6.1(Cr)	-	500	-
6.1(Mo)	-	500	-
6.1( Nitrogen%)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Copper %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(V)	-	500	-
6.1( Ti)	-	500	-
6.1(Cr)	-	500	-
6.1(Mo)	-	500	-
6.1(Ni)	-	500	-
6.1(Nitrogen%)	-	500	-

Complete

-
-

IS 3812 : Part 2 (2013)

Pulverized Fuel Ash - Part 2 : For Use as Admixture in Cement Mortar and Concrete

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(moisture content)	-	1000	-
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ) plus aluminium oxide (Al2O3 ) plus iron oxide (Fe2O3 ))	-	2000	-
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ))	-	1000	-
5.1, 6.1, Table 1(Magnesium oxide (MgO)	-	1000	-
5.1, 6.1, Table 1(Total sulphur as sulphur trioxide (SO3)	-	1000	-
5.1, 6.1, Table 1(Available alkalies as equivalent sodium oxide (Na2O))	-	1000	-
5.1, 6.1, Table 1(Total chlorides)	-	1000	-
5.1, 6.1, Table 1(Loss on ignition)	-	1000	-
7.1, Table 1(Fineness — Specific surface in m2 /kg)	-	1000	-
7.1, Table 1(Particles retained on 45 micron IS sieve (wet sieving))	-	1000	-
7.1, Table 1(Soundnes)	-	1500	-

Complete

-
-

IS 13801 (2013)

Chequered Cement Concrete Tiles -

Class-Gen Pur /Heavy Duty/Type-Plain (cement/ colored)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	500	-
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	0	-
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	0	-
Cl 11(Finish)	-	0	-
Cl 11(Finish)	-	0	-
Cl 11(Finish)	-	0	-
Cl 12.1(Concavity & Convexity )	-	500	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	500	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	500	-
Cl 12.4(Water absorption)	-	1000	-
Cl 12.5(Wet transverse strength)	-	2000	-
Cl 12.6(Resistance to wear)	-	2500	-
Cl 12.6(Resistance to wear)	-	2500	-

Complete

-
-

IS 1180 : Part 1 (2014)

Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision)

Distribution Transformers 11 KV upto 2500 KVA Rating

105000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.2 e)(Measurement of insulation resistance)	-	500	-
13.1(Marking (Rating Plates))	-	0	-
13.2(Terminal Marking Plate)	-	0	-
13.3(Marking )	-	0	-
13.4(Marking)	-	0.00	-
13.4.1(Marking)	-	0.00	-
14.1(MOUNTING ARRANGEMENT)	-	0	-
14.2(MOUNTING ARRANGEMENT)	-	0	-
14.3(MOUNTING ARRANGEMENT)	-	0	-
14.4(MOUNTING ARRANGEMENT)	-	0	-
15.1.1(TRANSFORMER TANK : Construction)	-	0	-
15.1.2(TRANSFORMER TANK : Construction)	-	0	-
15.1.3(TRANSFORMER TANK : Construction)	-	0	-
15.1.4(TRANSFORMER TANK : Construction)	-	0	-
15.1.5(TRANSFORMER TANK : Construction)	-	0	-
17( ABILITY OF TRANSFORMERS TO WITHSTAND EXTERNAL SHORT CIRCUIT )	-	0	-
21.2 a)(Measurement of winding resistance )	-	1000	-
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	1000	-
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	5000	-
21.2 d)(Measurement of no-load loss and current)	-	5000	-
21.2 f)(Induced over-voltage withstand test)	-	1000	-
21.2 g)( Separate-source voltage withstand test)	-	1000	-
21.3(a )(Lightning impulse test)	-	35000	-
21.5.3.3(Oil leakage test)	-	2000	-
21.3(b)(Temperature-rise test)	-	25000	-
21.3(c)(Short-circuit withstand test)	-	0	-
21.4 a)( Determination of sound levels)	-	2000	-
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	6000	-
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	3000	-
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	0	-
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	0	-
21.5.2.3( Oil leakage test (routine test))	-	2000	-
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	0	-
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	0	-
21.5.3.3(Oil leakage test (routine test))	-	2000	-
21.4 b(Short-circuit withstand test IS 2026 (Part 5) (above 200 kVA))	-	0	-
21.4 c(No load current at 112.5 percent voltage.)	-	2500	-
21.4 d(Paint adhesion tests)	-	1000	-
21.4 e(BDV and moisture content of oil in the transformer)	-	4000	-
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	6000	-
11(Minimum clearance in Air)	-	0	-
16(Conservator for Non-sealed type Transformers)	-	0	-
20(Fittings)	-	0	-
15.5(Total Dry Film Paint Thickness)	-	0	-

Complete

-
-

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

PPC (CCB)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	0	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-

Complete

-
-

IS/IEC 60898 : PART 1 (2015)

Electrical accessories - Circuit - Breakers for overcurrent protection for household and similar installations: Part 1 circuit - Breakers for a.c. operation (First Revision)

0.5-125A,210-460V,SP,DP,TP,FP TPN MCBs

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Classification, IS 60898-1)	-	500	Rs500/- for all Classification Parameter
4.3(Classification, IS 60898-1)	-	0	Rs500/- for all Classification Parameter
4.4(Classification, IS 60898-1)	-	0	Rs500/- for all Classification Parameter
4.5(Classification, IS 60898-1)	-	0	Rs500/- for all Classification Parameter
4.5.1(Classification, IS 60898-1)	-	0	Rs500/- for all Classification Parameter
4.5.2(Classification, IS 60898-1)	-	0	Rs500/- for all Classification Parameter
4.6(Classification, IS 60898-1)	-	0	Rs500/- for all Classification Parameter
4.7(Classification, IS 60898-1)	-	0	Rs500/- for all Classification Parameter
6(Marking and other product information, IS 60898-1)	-	500	-
8.1.1(General, IS 60898-1)	-	500	-
8.1.2(Mechanism, IS 60898-1)	-	500	-
8.1.3(Clearances and creepage distances, IS 60898-1)	-	500	-
8.1.4.1(Reliability of Screws current carrying parts and connections IS 60898-1)	-	1000	Rs1000/- for all Reliability of Screws current carrying parts and connections Parameter
8.1.4.2(Reliability of Screws current carrying parts and connections IS 60898-1)	-	0	Rs1000/- for all Reliability of Screws current carrying parts and connections Parameter
8.1.4.3(Reliability of Screws current carrying parts and connections IS 60898-1)	-	0	Rs1000/- for all Reliability of Screws current carrying parts and connections Parameter
8.1.4.4(Reliability of Screws current carrying parts and connections IS 60898-1)	-	0	Rs1000/- for all Reliability of Screws current carrying parts and connections Parameter
8.1.5.1(Reliability of terminals for external conductors, IS 60898-1)	-	1000	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.2(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.3(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.4(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.5(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.6(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.7(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.8(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.9(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.10(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.11(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.1.5.12(Reliability of terminals for external conductors, IS 60898-1)	-	0	Rs1000/- for all Reliability of terminals for external conductors, Parameter
8.2(Protection against Electric Shock, IS 60898-1)	-	1000	-
8.3.2(Dielectric strength at power frequency, IS 60898-1)	-	500	-
8.3.3(Isolating capability, IS 60898-1)	-	1000	-
8.3.4(Dielectric strength at rated impulse withstand voltage ( Uimp), IS 60898-1)	-	5000	-
8.4(Temperature-rise, IS 60898-1)	-	5000	-
8.5(Uninterrupted duty, IS 60898-1)	-	1000	-
8.6(Automatic operation, IS 60898-1)	-	1000	-
8.7(Mechanical and electrical endurance, IS 60898-1)	-	40000	-
8.8(Performance at short-circuit currents, IS 60898-1)	-	45000	-
8.9(Resistance to mechanical shock and impact, IS 60898-1)	-	1000	-
8.1(Resistance to heat, IS 60898-1)	-	1000	-
8.11(Resistance to abnormal heat and to fire, IS 60898-1)	-	1500	-
8.12(Resistance to rusting, IS 60898-1)	-	1000	-
8.13(Power loss, IS 60898-1)	-	500	-
9.3(Test of indelibility of marking, IS 60898-1)	-	500	-
9.4(Test of reliability of screws, current-carrying parts and connections, IS 60898-1)	-	1000	Rs1000/- for all test of reliability of screws, current-carrying parts and connections, Parameter
9.5.1(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	0	Rs1000/- for all test of reliability of screws, current-carrying parts and connections, Parameter
9.5.2(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	0	Rs1000/- for all test of reliability of screws, current-carrying parts and connections, Parameter
9.5.3(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	1000	Rs1000/- for all test of reliability of screw-type terminals for external copper conductors,, Parameter
9.5.4(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	0	Rs1000/- for all test of reliability of screw-type terminals for external copper conductors,, Parameter
9.6(Test of protection against electric shock, IS 60898-1)	-	500	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.1(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.2(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.3(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.4(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.5.1(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.5.2(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.5.3(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.7.5.4(Test of protection against electric shock, IS 60898-1)	-	0	Rs500/- for all test of Test of protection against electric shock, Parameter
9.8(Test of temperature-rise and measurement of power loss, IS 60898-1)	-	5000	Rs5000/- for all Test of temperature-rise and measurement of power loss, Parameter
9.8.5(Test of temperature-rise and measurement of power loss, IS 60898-1)	-	0	Rs5000/- for all Test of temperature-rise and measurement of power loss, Parameter
9.9(28- day test, IS 60898-1)	-	45000	-
9.10.2(Test of tripping characteristic, IS 60898-1)	-	55000	Rs55000/- for all Test of tripping characteristic,, Parameter
9.10.3(Test of tripping characteristic, IS 60898-1)	-	0	Rs55000/- for all Test of tripping characteristic,, Parameter
9.10.4(Test of tripping characteristic, IS 60898-1)	-	0	Rs55000/- for all Test of tripping characteristic,, Parameter
9.10.5(Test of tripping characteristic, IS 60898-1)	-	0	Rs55000/- for all Test of tripping characteristic,, Parameter
9.11(Verification of mechanical and electrical endurance, IS 60898-1)	-	30000	-
9.12(Short- Circuit tests, IS 60898-1)	-	75000	-
9.13.1(Mechanical Stress, IS 60898-1)	-	1000	-
9.13.2.2(Mechanical Stress, IS 60898-1)	-	0	-
9.13.2.3(Mechanical Stress, IS 60898-1)	-	0	-
9.13.2.4(Mechanical Stress, IS 60898-1)	-	0	-
9.13.2.5(Mechanical Stress, IS 60898-1)	-	0	-
9.14.1(Test of resistance to heat, IS 60898-1)	-	1000	-
9.14.3(Test of resistance to heat, IS 60898-1)	-	0	-
9.15(Resistance to abnormal heat and to fire)	-	1500	-
9.16(Test of resistance to rusting)	-	1000	-

Complete

-
-

IS 277 (2018)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8.1(UTM)	-	0	-
Cl. 8.1 (Cl. 8.1 (Tensile Strength))	-	1000	-
Cl. 8.1 (Cl. 8.1 (Yield Stress))	-	500	-
Cl. 8.1 (Cl. 8.1 (Percentage Elongation ))	-	500	-
Cl.12(Freedom from defects)	-	1000	-
Cl 8.2(Press)	-	1000	-
Cl 14(Length, Width & Thickness)	-	500	-
Cl 13(Weight)	-	0	-
5.1(carbon)	-	500	-
5.1(sulphur)	-	500	-
5.1(phosphorus)	-	500	-
5.1(manganese)	-	500	-
5.1(silicon )	-	500	-
5.1(Titanium)	-	500	-
5.1(nitrogen)	-	500	-
5.1(aluminium)	-	500	-
5.1(copper)	-	500	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
5.1(phosphorus)	-	500	-
5.1(nitrogen)	-	500	-
5.1(micro alloy)	-	2000	-
5.1(micro alloy)	-	2000	-
5.1(silicon )	-	500	-
5.1(aluminium)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
5.1(manganese)	-	500	-
5.1(phosphorus)	-	500	-
5.1(sulphur)	-	500	-
5.1(carbon)	-	500	-
Cl 10(Galvanising Test)	-	2000	-
Cl 10(Galvanising Test)	-	2000	-
Cl 10(Galvanising Test)	-	2000	-
7.4(Mass of Coating: Triple Spot Test)	-	2000	-
7.4(Mass of Coating: Triple Spot Test)	-	2000	-
7.4(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	2000	-

Complete

-
-

Bureau of Indian Standards

The National Standards Body of India

National Test House (NR)

Kamla Nehru Nagar,Ghaziabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

9999472699 [email protected]

Scope List

No Record Found

No Record Found