BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Office Laboratory (SROL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- [email protected]

Scope List

Reset

245 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 774 (2004)

Flushing cisterns for water closets and urinals (Other Than Plastic Cisterns) - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (CONSTRUCTION-Cistern)	-
5.2 (Cover)	-
5.3 (Flush Pipe-For high density polyethylene and unplasncized PVC pipes, the outside diameter of the pipes shall be 40 mm)	-
5.3 (Flush Pipe-whereas the lead flush pipe shall have a mimmum thickness of 3 5 mm)	-
5.3.1 (Flush Pipe Connection to Cistern- The length ofthe outlet shall be 37 ± 2 mm)	-
5.3.1 (Flush Pipe Connection to Cistern-The nommal mternal diameter of the cistern outlet shall be not less than 32 mm for high-level cisterns)	-
5.3.1 (Flush Pipe Connection to Cistern)	-
5.3.1 (Flush Pipe Connection to Cistern- )	-
5.4 (Inlet and Overflow Holes)	-
5.4 (Inlet and Overflow Holes-)	-
5.6 (Lever)	-
5.7 (Chain)	-
5.8 (Overflow Pipe-)	-
7.1 (OPERATIONAL AND PERFORMANCE REQUIREMENTS- Flushing Arrangement)	-
7.2 (Working Water Level-The working water level shall be a minimum of 65 cm below the effective top edge of the cistern and shall be legibly and permanently marked on the inside of the cistern)	-
7.3 (Freedom from Self-Siphonage)	-
7.4 (Reduced Water Level)	-
7.5,8.1 (Discharge Capacity-Dual-flush cisterns of of 6/3 litre capacity shall discharge 6 ± 0.5 litres and alternatively a reduced flush of 3 ± 0.5 litre.’)	-
7.6,8.2 (Discharge Rate-The discharge rate for flushing cistern of 10/5 litre capacity shall be 10 ± 0.5 litre within 6 s and 5 ± 0.5 litre within 3 s for full and reduced flush respectively)	-
7.6,8.2 (Discharge Rate-The discharge rate for flushing cistern of 6/3 litres capacity shall be 6 ± 0.5 litres within 4 s and 3 ± 0.5 litre within 2 s for full and reduced flush respectively.)	-

Partial

-
-

IS 4964 (2013)

Textiles – Vests, cotton, plain (Single jersey) knitted – Specification (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4/4.1/4.1.1 (MANUFACTURE AND FINISH- Fabric-The mass of the vest-method given in B-5.)	-
4/4.2-Fig. 1A, Fig. 1B, Fig. 2A, Fig. 2B, Fig. 3. (MANUFACTURE AND FINISH)	-
4/4.2/4.2.1 (MANUFACTURE AND FINISH)	-
4/4.3/4.3.1-see IS 11161, see IS 10789, Table 1. (MANUFACTURE AND FINISH-Seams and Stitches)	-
4/4.3/4.3.2-according to B-4 (MANUFACTURE AND FINISH-Seams and Stitches-Dimension)	-
4/4.6 (MANUFACTURE AND FINISH-Freedom from Defects)	-
5/5.1-Tables 2 and 3 (REQUIREMENTS-Dimensions-method prescribed in Annex B.)	-
5/5.2-Tables 4 (REQUIREMENTS-Other Requirements-Dimension)	-

Partial

-
-

IS 1784 (2020)

Screwed Closures for Drums — Specification ( Fourth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Dimensions-Steel flange- d1)	-
6 (Dimensions-Steel flange- d2)	-
6 (Dimensions-Steel flange- d3)	-
6 (Dimensions-Steel flange- d4)	-
6 (Dimensions-Steel flange- s1)	-
6 (Dimensions-Steel flange- t1)	-
6 (Dimensions-Flange Gasket- wd)	-
6 (Dimensions-Flange Gasket-ww)	-
6 (Dimensions-Flange Gasket-wt)	-
6 (Dimensions-Steel Bung- d1)	-
6 (Dimensions-Steel Bung- p1)	-
6 (Dimensions-Steel Bung- p2)	-
6 (Dimensions-Steel Bung- p3)	-
6 (Dimensions-Flange Gasket- wd)	-
6 (Dimensions-Bung Gasket- ww)	-
6 (Dimensions-Bung Gasket- wt)	-
6 (Dimensions-Capseals- d1)	-
6 (Dimensions-Capseals- d2)	-
6 (Dimensions-Capseals- h1)	-
6 (Dimensions-Capseals- h2)	-
6 (Dimensions-Capseals- w1)	-
6 (Dimensions-Tag Ring- d1)	-
6 (Dimensions-Tag Ring- d2)	-
6 (Dimensions-Tag Ring- d3)	-
6 (Dimensions-Tag Ring- d4)	-
6 (Dimensions-Tag Ring- d5)	-
6 (Dimensions-Tag Ring- h1)	-
6 (Dimensions-Zinc Bung- d1)	-
6 (Dimensions-Zinc Bung- d2)	-
6 (Dimensions-Zinc Bung- d3)	-
6 (Dimensions-Zinc Bung- p1)	-
7 (Finish)	-
8.1 (Interchangeability)	-

Partial

-
-

IS 6392 (2020)

Steel Pipes Flanges — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Dimension)	-
7.3 (Joint Faces)	-
3.1 (Tensile Strength-IS 1608(P-1))	-
3.1 (Yield Stress-IS 1608(P-1))	-
3.1 (Elongation- IS 1608(P-1))	-
6.1 (Dimension)	-

Partial

-
-

IS 1536 (2001)

Centrifugally cast (Spun) iron pressure pipes for water, gas and sewage - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.2, annex-A (Tensile Test ( for pipes over 300mm))	-
11.3 (Brinell Hardness Test)	-
13.4 Table 5 (c)	-
13.4 Table 5 (D)	-
13.4 Table 5 (E)	-
13.4 Table 5 (b)	-
13.4 Table 5 (a)	-
13.4 Table 5 (r)	-
13.4 Table 5 (f)	-
13.4 Table 5 (s)	-
13.4 Table 5 (Holes Number)	-
13.4 Table 5 (Holes Diameter)	-
13.4 Table 5 (Diameter of Bolts)	-
13.5 Table 6 to 8 (DE Lead joint)	-
13.5 Table 6 to 8 (DE Push on joint)	-
13.5 Table 6 to 8 (e)	-
13.6 Table 9 (DE)	-
13.6 Table 9 (e)	-

Partial

-
-

IS 1538 (1993)

Cast iron fittings for pressure pipes for water, gas and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (tensile strength)	-
6.1 (Brinell hardness tests)	-
9.1,Table 4 (D)	-
9.1,Table 4 (a)	-
9.1,Table 4 (b)	-
9.1,Table 4 (s)	-
9.1,Table 4 (r)	-
9.1,Table 5 (D)	-
9.1,Table 5 (b)	-
9.1,Table 5 (c)	-
9.1,Table 5 (f)	-
9.1,Table 5 (s)	-
9.1,Table 5 (C)	-
9.1,Table 5 (Holes No)	-
9.1,Table 5 (Holes diameter)	-
9.1,Table 5 (Diameterof Bolts)	-
9.1,Table 6 (D)	-
9.1,Table 6 (C)	-
9.1,Table 6 (Holes No)	-
9.1,Table 6 (Holes diameter)	-
9.1,Table 6 (Diameterof Bolts)	-
9.1&11.1,Table 7,8&9 (e)	-
9.1&11.1,Table 7,8&9 (l)	-
9.1&11.1,Table 7,8&9 (Mass (Approx))	-
9.1&11.1,Table 10 to13 (e)	-
9.1&11.1,Table 10 to13 (Mass (Approx))	-
9.1&11.1,Table 14 (e)	-
9.1&11.1,Table 14 (l)	-
9.1&11.1,Table 14 (h)	-
9.1&11.1,Table 14 (Mass (Approx))	-
9.1&11.1,Table 15 (e)	-
9.1&11.1,Table 15 (l)	-
9.1&11.1,Table 15 (Mass (Approx))	-
9.1&11.1,Table 16 (e)	-
9.1&11.1,Table 16 (l)	-
9.1&11.1,Table 16 (h)	-
9.1&11.1,Table 16 (Mass (Approx))	-
9.1&11.1,Table 17 (e1)	-
9.1&11.1,Table 17 (l1)	-
9.1&11.1,Table 17 (e2)	-
9.1&11.1,Table 17 (l2)	-
9.1&11.1,Table 17 (l3)	-
9.1&11.1,Table 17 (l)	-
9.1&11.1,Table 17 (Mass)	-
9.1&11.1,Table 18 (a)	-
9.1&11.1,Table 18 (P)	-
9.1&11.1,Table 18 (Mass (Approx))	-
9.1&11.1,Table 19 (DC)	-
9.1&11.1,Table 19 (e)	-
9.1&11.1,Table 19 (a)	-
9.1&11.1,Table 19 (l)	-
9.1&11.1,Table 19 (Mass (Approx))	-
9.1&11.1,Table 20 (DI)	-
9.1&11.1,Table 20 (h)	-
9.1&11.1,Table 20 (Mass (Approx))	-
9.1&11.1,Table 21 (e)	-
9.1&11.1,Table 21 (Mass (Approx))	-
9.1&11.1,Table 21 (e)	-
9.1&11.1,Table 22 (a)	-
9.1&11.1,Table 22 (b)	-
9.1&11.1,Table 22 (c)	-
9.1&11.1,Table 22 (g)	-
9.1&11.1,Table 23 (e)	-
9.1&11.1,Table 23 (Mass (Approx))	-
9.1&11.1,Table 24 (e)	-
9.1&11.1,Table 24 (l)	-
9.1&11.1,Table 24 (e1)	-
9.1&11.1,Table 24 (h)	-
9.1&11.1,Table 24 (Mass (Approx))	-
9.1&11.1,Table 25 (e)	-
9.1&11.1,Table 25 (l)	-
9.1&11.1,Table 25 (h)	-
9.1&11.1,Table 25 (Mass (Approx))	-
9.1&11.1,Table 26 (e1)	-
9.1&11.1,Table 26 (e2)	-
9.1&11.1,Table 26 (l)	-
9.1&11.1,Table 26 (Mass (Approx))	-
9.1&11.1,Table 27 (e1)	-
9.1&11.1,Table 27 (e2)	-
9.1&11.1,Table 27 (l3)	-
9.1&11.1,Table 27 (Mass)	-
9.1&11.1,Table 28 (D)	-
9.1&11.1,Table 28 (t)	-
9.1&11.1,Table 28 (Mass (Approx))	-
12.1 to 12.7 (Coating )	-

Partial

-
-

IS 1703 (2000)

Water Fittings - Copper Alloy Float Valves (Horizontal Plunger Type) -

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (CLASSIFICATION)	-
4 (NOMINAL SIZES)	-
6 (MANUFACTURE AND WORKMANSHIP)	-
6.2 (Machining)	-
7.2 and Fig.1 (CONSTRUCTION)	-
7.3 and Fig.1 (CONSTRUCTION)	-
7.4 (Dimensions of Body)	-
7.6 (Piston)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers - A)	-
7.7.2 (Levers)	-
7.7.3 (Levers)	-
7.7.4 (Short arm of the lever)	-
7.7.6 (Levers)	-
7.7.7 (Piston Travel)	-
7.9.1 (Silencing Pipes and Anti-Siphonage Provision)	-
7.9.2 (Silencing Pipes and Anti-Siphonage Provision)	-
7.1 (Floats - Dia of float IS 9762)	-
7.1 (Floats - Wall thickness IS 9762)	-

Partial

-
-

IS 1729 (2002)

Cast iron/ductile iron drainage pipes and pipe fittings for over ground non-pressure pipeline socket and spigot series (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Tensile Strrngth - IS1608(Pt-1))	-
5.1 (Elongation - IS 1608(Pt-1))	-
5.3 (Casting Defects)	-
5.4 (Hardness- IS 1500)	-
6 (Hammer Test - IS1729)	-
11 (Coating Test at 65degree Celcius )	-
11 (Coating Test at 0degree Celcius )	-

Partial

-
-

IS 1342 (2019)

Oil pressure stoves - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4/4.1 (DESIGNATION, TYPES AND FUEL CAPACITY , )	-
4/4.1 (DESIGNATION, TYPES AND FUEL CAPACITY , )	-
4/4.1 (DESIGNATION, TYPES AND FUEL CAPACITY , )	-
4/4.1.1 ( Volume of the oil hold in fuel tank)	-
6/6.1/Fig 1(Shape) and Fig. 2, 4, 5, 6 and 11(Dimensions) . (SHAPE AND DIMENSIONS /for designation OTR for roarer type burner and OTS for silencer type burner)	-
6/6.2/Fig 3(Shape) and Fig. 2, 4, 5, 11, 12, 14 and 16.(Dimensions) . (SHAPE AND DIMENSIONS /for designation OR for roarer type burner and OS for silencer type burner)	-
7/7.1/7.1.2 (CONSTRUCTION)	-
7/7.1/7.1.3 (CONSTRUCTION/The stove shall be so made as to be firm on its base and the legs shall be so fitted as to have the bottom of the fuel container at least 13 mm clear of the ground on which stove stands.)	-
7/7.1/7.1.3 (CONSTRUCTION)	-
7/7.1/7.1.4 (CONSTRUCTION)	-
7/7.1/7.1.4 (CONSTRUCTION)	-
7/7.2- IS 8808 (Burner assembly)	-
7/7.3 (Pump)	-
7/7.4/7.4.1 (Pressure - Release Screw)	-
7/7.5 (Filler cap assembly)	-
7/7.7 (Pricker)	-
7/7.8 (Interchangeable Parts )	-
7/7.9 Refer Table-2 (Strength of Body of Stove)	-
8 (Finish)	-
9/9.1/9.1.1 (Air Pressure Test)	-
9/9.1/9.1.2 (Safety Pressure Test)	-
9/9.1/9.1.3 ( Bursting Pressure Test)	-
9/9.2 Annex D (Fuel Consumption )	-
9/9.4 Annex E. (Surface Temperature and Fuel Temperature Test (Type Test))	-
9/9.5 Annex F. ( Combustion Efficiency Test (Type Test)/carbon monoxide/carbon dioxide )	-
9/9.6 Annex F. (Resistance to Draught (Type Test))	-
9/9.7 (Fuel Creep)	-

Partial

-
-

IS 3466 (1988)

Specification For Masonry Cement

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 Table 1 i (Fineness IS : 4031:1988)	-
3.1 Table 1 i (Fineness IS : 4031:1988)	-
3.1 Table 1 ii a (Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-
3.1 Table 1 ii a (Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-
3.1 Table 1 ii a (Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-
3.1 Table 1 ii a (Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-
3.1 Table 1 ii a (Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-
3.1 Table 1 ii b (Setting Time ( by Vicat Apparatus ), Final IS : 4031:1988)	-
3.1 Table 1 ii b (Setting Time ( by Vicat Apparatus ), Final IS : 4031:1988)	-
3.1 Table 1 iii a (Soundness, Le-Chate1ier expansion IS 4031:1988)	-
3.1 Table 1 iii a (Soundness, Le-Chate1ier expansion IS 4031:1988)	-
3.1 Table 1 iii b (Soundness, Autoclave expansion IS 4031:1988)	-
3.1 Table 1 iii b (Soundness, Autoclave expansion IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-

Partial

-
-

IS 12600 (1989)

Portland cement, low heat - specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Fineness 4031 Part 2)	-
6.2.1 (Expansion by Le Chatelier- 4031 Part 3)	-
6.2.1 (Expansion by Autoclave- 4031 Part 3)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-

Partial

-
-

IS 12337 (1988)

Specification for manually operated fertilizer broadcaster

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Constructional Requirements- Hopper)	-
4.1.1 (Constructional Requirements- Hopper)	-
4.2 (Constructional Requirements- Spreading Disc)	-
4.3 (Constructional Requirements- Feed Control Mechanism)	-
4.4 (Constructional Requirements- Agitator)	-
4.5 (Constructional Requirements- Gear Box and Gears)	-
4.6 (Constructional Requirements- Crank)	-
4.7 (Constructional Requirements- Straps)	-
4.7.1 (Constructional Requirements- Straps (Strap Drop Test))	-
4.7 (Constructional Requirements- Straps (cushion width))	-
4.7 (Constructional Requirements- Straps (cushion thickness))	-
4.7.1 (Constructional Requirements- Straps (Strap Drop Test))	-
4.8 (Constructional Requirements- Bearings)	-
4.9 (Constructional Requirements- Total Mass)	-
4.10. (Constructional Requirements)	-
5 (Capacity)	-
6.1 (Workmanship and Finish)	-
6.2 (Workmanship and Finish)	-

Partial

-
-

IS 8329 (2000)

Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 10 (Hardness & Tensile Test)	-
Cl 11 (Hydrostatic Test)	-
Cl 13 (Length, Diameter, Wall Thickness & Ovality)	-

Partial

-
-

IS 1038 (1983)

Specification For Steel Doors, Windows And Ventilators

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1. (Size-Height)	-
4.1 (Size-Width)	-
4.1. (Size-Height)	-
4.1 (Size-Width)	-
4.1. (Size-Height)	-
4.1 (Size-Width)	-
4.3 (Designation)	-
6.1.1.1 (Visual Inspection Test)	-
6.2 (Side Hung Shutter- Thickness of hinge)	-
6.2 (Side Hung Shutter- Pin diameter)	-
6.2 (Side Hung Shutter)	-
6.2 (Side Hung Shutter-Width of hinge)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate-Material of handel )	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate- Thicknesss of handle)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate-Height of handle plate)	-
6.2.3 (Peg Stay - Material)	-
6.2.3 (Peg Stay - Thickness)	-
6.2.3 (Peg Stay )	-
6.3 (Top Hung Ventilator)	-
6.3 (Top Hung Ventilator-Thickness of hinge)	-
6.3 (Top Hung Ventilator-Pin diameter)	-
6.3 (Top Hung Ventilator-Width of hinge)	-
7.1 (Position of Holes)	-
7.2 Table 2 (Position of Fixing Screws)	-
7.2 Table 2 (Lugs-A)	-
7.2 Table 2 (Lugs-B)	-
7.2 Table 2 (Lugs-C)	-
7.2 Table 2 (Lugs-D)	-
7.2 Table 2 (Lugs-E)	-
6.2.3 (Peg Stay - Dimensions-F)	-
7.2 Table 2 (Lugs-G)	-
8 (Finish)	-
9 (Glazing)	-

Partial

-
-

IS 4308 (2019)

Dry Chemical Powders for Fire Fighting — BC, ABC and D Types — Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 5 Table 1(iii) (Apparent density (Declared value by the manufacturer))	-
Clause 5 Table 1(iv) (Particle size / sieve analysis (Declared value by the manufacturer))	-
Clause 5 Table 1(vi) (Water repellency)	-
Clause 5 Table 1(vii) (Moisture content)	-
Clause 5 Table 1(xii) (colour)	-

Partial

-
-

IS 11722 (1986)

Specification for thin walled flexible quick coupling pipes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Pipe Manufacturing Process )	-
5,5.1 (Workmsnship &Finish)	-
6 &7 ; Table 1 (Dimension & Tolerance)	-
8 (Length)	-
12 (Straightness)	-
13.1 (Flattening Test,IS 2328)	-
13.2 (Tensile Test ,; IS 1608(P1))	-

Partial

-
-

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Freedom from defects , IS 4224)	-
5 (Sizes and Tolerances - IS 4224)	-
6 (Finish)	-
7.1 (Tensile Test - IS 1608(Pt -1))	-

Complete

-
-

IS 903 (1993)

Specification for Fire Hose Delivery Couplings, Branch Pipe, Nozzles And Nozzle Spanner - Specificaion

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Finish and workmanship)	-
4 (Marking)	-
5 (Delivery hose coupling)	-
5.3 (Size and Dimension )	-
7.3 (Hydraulic test requirement)	-
6 (Branch pipe)	-
6.3 (Hydraulic test requirement)	-
7 (Nozzle)	-
7.3 (Hydraulic test requirement)	-
8.2 (Shape & Dimensions of Spanner)	-
8.4 (Deflection test of Spanner)	-

Complete

-
-

IS 13997 (2014)

Drums, large open top - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1 (Dimensions-D2)	-
5, Table 1 (Dimensions-D3)	-
5, Table 1 (Dimensions-D4)	-
5, Table 1 (Dimensions-H1)	-
5, Table 1 (Dimensions-H5)	-
5, Table 1 (Dimensions-h2)	-
5, Table 1 (Dimensions-h3)	-
5, Table 1 (Dimensions-h4)	-
5, Table 1 (Dimensions-p1)	-
6.2 (The nominal thickness of steel sheets for body and ends )	-
7.1 ( CONSTRUCTION)	-
7.2 ( CONSTRUCTION)	-
7.3 ( CONSTRUCTION- Double Seam/Spiral Seam/Triple Seam Construction for Grade A Drums)	-
7.4 ( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums)	-
7.5 ( CONSTRUCTION)	-
7.6 ( CONSTRUCTION)	-
7.7 ( CONSTRUCTION)	-
7.8 ( CONSTRUCTION)	-
7.9 (Closures)	-
7.10(a) (Closures)	-
7.10(b) (Closures)	-
7.10(c) (Closures)	-
7.10(d) (Closures)	-
7.11 ( Locking Ring)	-
8.1 (FINISH )	-
8.2 (FINISH )	-
9 (leakage test)	-

Complete

-
-

IS 2653 (2004)

Safety matches in boxes - Specification (Third Revision)

- View breakup
Rs 2570.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.2.1 (Matchboxes)	-
5.1.2.2 (Matchboxes)	-
5.1.3 (Envelopment)	-
5.1.4 (Ease of Opening)	-
5.1.5 (Retention of Contents)	-
5.1.6.1 (Defective Match Boxes)	-
5.1.6.2 (Defective Match Boxes)	-
5.2.1.1 (Match Splints)	-
5.2.1.2 (Match Splints)	-
5.2.1.2 (Minimum thickness)	-
5.2.1.2 (Average thickness)	-
5.2.2 (Unserviceable Sticks)	-
5.3 (Match Boxes)	-
6.1.1 (Striking Performance - General)	-
6.1.2 (Safety Matches)	-
6.2 (Ignition Below 170 ˚C)	-
6.3 (Ignition Under Impact)	-
6.4.1 (Durability of the Striking Surface)	-
6.4.2 (Ignition of the Striking Surface)	-
6.4.3 (Loss of Burning Fragments)	-
6.5 (Damp Proofness for Match Boxes)	-

Complete

-
-

IS 3196 : Part 2 (2006)

Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gases: Part 2 cylinders for liquefiable non - Toxic gases other than lpg - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
19 (Marking)	-
9 (Valve Connection)	-
9 (Valve Protection)	-
9 (Valve Protection)	-
9 (Valve Protection)	-
10 (Handle)	-
10 (Foot ring)	-
10 (Foot ring)	-
10 (Foot ring)	-
10.3 (Bung)	-
14 (Water Capacity)	-
16 (Pneumatic Leakage Test)	-
18.1.3 (Root Bend test,)	-
18.1.3 (Face Bend Test,)	-
18.1.5 (Minimum Thickness test)	-
20 (Colour Identification)	-
10.3 (Bung)	-

Partial

-
-

IS 6006 (2014)

Uncoated stress relieved strand for prestressed concrete - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Weight)	-
Cl 7 (Tensile Test On UTM)	-
Cl 4 (Length )	-
Cl 4 (Joints)	-
Cl 4.5 (Workmanship)	-

Partial

-
-

IS 2556 : Part 6 (1995)

Vitreous sanitary appliances (Vitreous China): Part 6 specific requirements of urinals and partition plates

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (Patterns and Size)	-
Cl 5 (Dimensions & Tolerances)	-
Cl 6 (Construction)	-
Cl 7 (Finish)	-

Partial

-
-

IS 2556 : Part 7 (1995)

Vitreous sanitary appliances (Vitreous China) - specification: Part 7 specific requirements of accessories for sanitary appliances

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-
3 (General requirements-Thickness IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-
4 (DIMENSIONS-STOP END CHANNEL WITH OUTLET-Type A )	-
4 (DIMENSIONS-STOP END CHANNEL WITH OUTLET-Type B )	-
4 (DIMENSIONS-PLAIN CHENNEL-Type A )	-
4 (DIMENSIONS-PLAIN CHENNEL-Type B )	-
4 (DIMENSIONS-PLAIN CHANNEL WITH SOCKET-Type A )	-
4 (DIMENSIONS-PLAIN CHANNEL WITH SOCKET-Type B )	-
4 (DIMENSIONS-FOOT REST )	-
4 (DIMENSIONS-- FLOOR TRAP)	-
4 (DIMENSIONS-TYPICAL ILLUSTRATION OF VITRIOUS SHOWER ROSH)	-
5 (CONSTRUCTION)	-
6 (FINISH)	-
4 (DIMENSIONS-- Ovality permissible within the variation allowed for the dimensioN )	-

Partial

-
-

IS 2098 (1997)

Asbestos cement building boards - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 Table -1 ( TOLERANCES - 1.Tolerance on Length & Width)	-
7.2 Table -1 (2.Tolerance on Thickness )	-
8.4 (TESTS-Water Absorption Test )	-
11 (MARKING-Each board shall be stamped or marked by any suitable method on non weathering side with the following information: )	-

Partial

-
-

IS 3196 : Part 4 (2001)

Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gases - Specification: Part 4 cylinders for toxic and corrosive gases

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
19 (Marking)	-
4 (Material)	-
9.3 (Valve Protection)	-
9.3 (Valve Protection)	-
10.2 (Foot ring)	-
14 (Water Capacity)	-
15 (Hydrostatic test)	-
4 (Material,Bung)	-
16 (Pneumatic Leakage Test)	-
17.2 (Bursting test)	-
8.4 (Agreed finished Thickness )	-
20 (Colour Identification)	-
19 (Marking)	-
9.3 (Valve Protection)	-
14 (Water Capacity)	-
15 (Hydrostatic test)	-
16 (Pneumatic Leakage Test)	-
17.2 (Bursting test)	-
18.1.3 (Face Bend Test,)	-
18.1.7 (Macro Examination)	-
8.4 (Agreed finished Thickness )	-
20 (Colour Identification)	-

Partial

-
-

IS 1812 (1982)

Specification for carbon steel wire for the manufacture of wood screws (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 ( Tensile Test IS1608(P-1))	-
6.3 ( Wrapping Test )	-
7 (. SIZE TOLERANCE)	-
8 ( FREEDOM FROM DEFECTS)	-

Partial

-
-

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Freedom from defects , IS 5517)	-
8,Table 6 (Hardness Test - IS 1500(Pt -1))	-
9, Table 5 (Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-

Partial

-
-

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
5.2.1 Table 1 (Particulars-Barrel Tower Bolts)	-
5.2.2 Table 2 (Particulars-Skeleton Tower Bolts)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-
6.1- Table 1 (Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-
6.2- Table 3 (PACKING)	-

Partial

-
-

IS 1726 (1991)

Cast iron manhole covers and frames - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (GRADES )	-
3 (TYPES)	-
5.1.1 (Covers and Frames)	-
5.1.2 (The rise of the chequer)	-
5.2 (Key Holes and Keys)	-
5.3 (Locking Devices)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - O)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - O1)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - F)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - F1)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - f)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - f1)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - Fd)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - fd)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - S)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - t)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - t1)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - C)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - C1)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - T)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - T1)	-
7 and Table 2 and Fig.3 to 9 (DIMENSIONS OF MANHOLE COVERS AND FRAMES - Clearence (C1))	-
8 (COATING - At 63˚C)	-
8 (COATING - At 0˚C)	-

Partial

-
-

First
Prev
2
3
4
5
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Office Laboratory (SROL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- [email protected]

Scope List