BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Office Laboratory (SROL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- [email protected]

Scope List

Reset

245 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 269 (2013)

Ordinary Portland Cement, 33 Grade

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Strength requiement for Seat Cl9.1 (The seat shall withstand the load of 1150 N for 30 minutes without permanent distortion of the seat or the hinge fittings or damage to any finish.)	-

Partial

-
-

IS 1489 : PART 1 (1991)

Specification for Portland pozzolana cement Part 1 Flyash based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Strength requiement for Seat Cl9.1 (The seat shall withstand the load of 1150 N for 30 minutes without permanent distortion of the seat or the hinge fittings or damage to any finish.)	-

Partial

-
-

IS 2556 : Part 16 (2002)

Vitreous sanitary appliances (Vitreous China) - Specification: Part 16 specific requirements of wash down wall mounted water closets

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
"3 IS 2556(P1)" (GENERAL REQUIREMENTS)	-
"5 Table 1 & 2 " (DIMENSIONS AND TOLERANCES)	-
7 (FINISH)	-
6.1 (CONSTRUCTION)	-
8.1 ()	-
8.2 (Smudge Test)	-
8.3 (Holding Capacity Test)	-
8.4 (Single Ball Test)	-
9 (LOAD TEST)	-
4 (PATTERNS)	-

Partial

-
-

IS 13258 (2014)

Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gas - Requirements for inspection and reconditioning of used lpg cylinders (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.4 (Tare Weight Verification)	-
14 (HYDROSTATIC TEST)	-
16 (PNEUMATIC TEST)	-

Partial

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3 (CLASSIFICATION OF PIPES)	-
6.1 (VISUAL APPEARANCE)	-

Partial

-
-

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2.1 (Visual and Workmanship Requirement)	-

Partial

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 (Surface colour of the pipes shall be dark shade of grey)	-
Cl.7.1 (Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.1 ( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.1 ( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.2 (Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-
Cl.7.3.2 (Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-
Cl.8.1 (The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-
Cl.8.2 (When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-
Cl.8.4 (When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-
Cl.11. (Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-

Partial

-
-

IS 12395 (1988)

Specification for disposable trash bags of plastics

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

IS 7129 (2021)

POTASSIUM CARBONATE ANHYDROUS SPECIFICATION (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description)	-
4.3 - Table 1 - Sl No - i (Total Alkalinity (as K2CO3) - Annex A 2)	-
4.3 - Table 1 - Sl No - ii (Potassium bicarbonate (as KHCO3) - Annex A 3)	-
4.3 - Table 1 - Sl No - ii (Free alkali (as KOH)- Annex A 3)	-
4.3 - Table 1 - Sl No - iii (Sulphates (as K2SO4) - Annex A 4)	-
4.3 - Table 1 - Sl No - iv (Chlorides (as KCl) - Annex A 5)	-
4.3 - Table 1 - Sl No - v (Matter insoluble in water - Annex A 6)	-
4.3 - Table 1 - Sl No - vi (Iron (as Fe) - Annex A 7 & A 12)	-
4.3 - Table 1 - Sl No - vii (Heavy metals (as Pb - Annex A 8 & A 12)	-
4.3 - Table 1 - Sl No - viii (Loss on heating at 150oC - Annex A 9)	-
4.3 - Table 1 - Sl No - ix (Sodium (as Na) - Annex A 10 & A 12)	-

Partial

-
-

IS 2556 : Part 5 (1994)

Vitreous sanitary appliances (Vitreous China) - Specification: Part 5 specific requirements of laboratory sinks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (General requirements-Thickness IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-

Partial

-
-

IS 1165 (2002)

Milk Powder (Bi-lingual)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.5 (Bacterial count)	-
3.5.2 (Coliform count)	-
3.5.3 (Staphylococcus Aureus)	-
3.5.4 (Salmonella)	-
3.5.5 (Shigella)	-
3.4.5 (Moisture)	-
3.4.5 (Total solids)	-
3.4.5 (Fat)	-
3.4.5 (Insolubility index)	-
3.4.5 (Total ash)	-
3.1 (Description)	-
3.2 (Flavour and taste)	-
3.4.5 (Titratable acidity (lactic acid))	-

Partial

-
-

IS 1656 (2007)

Milk - Cereal based complementary foods - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4' 5.1 to 5.4 (Description)	-
5.6 (Flavour and odour)	-
5.8 (Total protein)	-
5.8 (Fat)	-
5.8 (Total Ash)	-
5.8 (Acid insoluble ash)	-
5.7.1 (Bacterial count)	-
5.7.2 (Coliform count)	-
5.7.3 (Escherichia coli)	-
5.7.4 (Staphylococcus aureus)	-
5.7.5 (Salmonella and shigella)	-
5.7.6 (Yeast and mould count)	-

Partial

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Colour)	-
10.1 (Surface Finish)	-
7.2.1.1 Table3 (Angle of taper (Note-1))	-
5 (CLASSIFICATION OF PIPES)	-
7 (DIMENSIONS-PIPE-Nominal Diameter)	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Minimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. Variation)	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-
7.1.1.2 (DIMENSIONS-PIPE-Ovality (Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Minimum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Average Thickness)	-
7.2.1 (DIMENSIONS-Socket)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-
7.2.1.2-Table 4 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-
8 (SEALING RINGS)	-
9.1 (PIPE ENDS)	-
10.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.1.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.2 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-
10.4 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-
10.5 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-
10.6 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-
11.1-Table 6 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-
11.1-Table 7 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-
11.1.1 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-
11.2 (Resistance to External Blows at 0°C)	-
7.1.4 (Length)	-
10.7 (Sulphated Ash Content)	-

Partial

-
-

IS 252 (2013)

Caustic soda - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Form and Description)	-
Cl. 3.3 and 3.4(Table 1, S. no i) (Sodium carbonate (as Na2CO3), percent by mass)	-

Partial

-
-

IS 1486 (1978)

Specification for copper oxychloride, technical

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 4654 (2019)

Paraffin Wax — Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 Table 1 (Ash, all types)	-
4.2 Table 1 (Saponification value, all types)	-

Partial

-
-

IS 3062 (1995)

Crop protection equipment - Rocker sprayer - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

-
-

IS 10146 (1982)

Specification for polyethylene for its safe use in contact with foodstuffs, pharmaceuticals and drinking water zy

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.4 (Overall Migration)	-

Partial

-
-

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 a) (Conductor : Material )	-
4.1.1 b) (Material : Seperator tape )	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1 (Class of conductor )	-
4.1.1 e) (Shape of conductor )	-
4.1.1 f) (Nominal size of conductor )	-
4.2.1, 11.2, 12.2, 13.2, 14.2 (Insulation : Material )	-
4.2.2, 11.2, 12.2, 13.2, 14.2 (Insulation : Application )	-
4.2.3,11.2, 12.2, 13.2 (Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-
4.2.3, 11.2, 12.2, 13.2, 14.2 (Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-
4.2.4 (Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-
4.2.4 (Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-
4.2.4 (Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-
4.2.5 (Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-
4.2.4 (Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-
4.2.5 (Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-
4.5.1,13.4, 14.4 (Sheath : Compound )	-
4.5.2, 13.4, 14.4 (Sheath : Application)	-
4.5.3,13.4, 14.4 (Thickness of sheath - Average : IS 10810 (Part 6))	-
4.5.3,13.4, 14.4 (Thickness of sheath - Minimum : IS 10810 (Part 6))	-
4.5.4, 13.4 (Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-
4.5.4,13.4 (Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-
4.5.4, 13.4, 14.4 (Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-
4.5.5, 13.4, 14.4 (Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-
4.5.4, 13.4, 14.4 (Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-
4.5.5, 13.4,14.4 (Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-
4.5.5, 11.3, 12.3, 13.6, 14.6 (Overall Dimensions)	-
4.5.5.1, 11.3, 12.3,13.5, 14.5 (Ovality)	-
4.5.6, 13.4 (Colour of Sheath)	-
5.1 (High Voltage Test (at Room Temperature))	-
5.3 (Flammability Test- IS 10810 (Part 53).)	-
5.12 (Hot Set Test- IS 10810 (Part 30).)	-
5.12 (Permanent Set - IS 10810 (Part 30).)	-
5.13 (Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-
5.13 (Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-
5.15 (Cold Bend Test-IS 10810 (Part 20).)	-
5.16 (Cold Impact Test- IS 10810 (Part 21).)	-
6.1, Table 1 (CORE IDENTIFICATION)	-
6.2 (Core Identification by Numbers)	-
6.2.1 (Preferred Arrangement of Marking)	-
6.2.2 (Durability)	-
7.0 (CABLE CODE)	-
9.0 ( IDENTIFICATION)	-
10.2.1 (Standards marking)	-
13.3, 14.3 (assembly of cores )	-
6.1 (General Requirements)	-
6.1.1 (Colour Combination Green Yellow)	-

Partial

-
-

IS 9857 (1990)

Welding cables - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Conductor : Material )	-
5 (SEPARATOR)	-
6 (COVERING)	-
7 (CONDUCTOR : CONSTRUCTION )	-
8 (S E P A R A T O R)	-
9.1 (C O V E R I N G : Application )	-
9.2 (T h i c k n e s s o f C o v e r i n g)	-
9.3 (T o l e r a n c e on Thickness o f C o v e r i n g)	-
9.4 (A p p l i c a t i o n of C o v e r i n g)	-
9.5 (Colour of C o v e r i n g)	-
10.1 a) 1) (Annealing test - IS 10810: Part 1)	-
10.1 a) 2) (Conductor resistance tes - IS 10810 : Part 5)	-
10.1 c) 1) (Physical tests for covering : Tensile strength )	-
10.1 c) 1) (Physical tests for covering : Elongation at break )	-
10.1 c) 2) (Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-
10.1 c) 2) (Physical tests for covering -Ageing in Air oven : Elongation at break )	-
10.1 c) 2) (Physical tests for covering - Ageing in Air oven : Tensile strength )	-
10.1 c) 2) (Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-
10.1 c) 5) (Hot set test )	-
11.1 (High Voltage Test ( Water Immersion Test ))	-
11.4 (Flammability Test)	-
12.1 (Manufacturer's Identification)	-
12.2 (Cable Identification)	-
12.3 (Cable Code)	-

Partial

-
-

IS 2593 (1984)

Flexible Cables for Miners' Cap-lamps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (CONDUCTOR)	-
3.1.2 (Resistance test )	-
4.1 (INSULATION)	-
6.1 (SHEATH)	-
7.1 (Construction : Conductor )	-
8.1 (Thickness of Insulation - Average )	-
8.1 (Thickness of Insulation - minimum)	-
9.1 (IDENTIFICATION OF CORES)	-
10.1 (LAYING UP)	-
11.1 (SHEATH : Application )	-
11.2 (Thickness of Sheath -average )	-
12.2 (Thickness of Sheath - Minimum)	-
11.3 (Coulor of sheath )	-
12.1 (OVERALL DIAMETER)	-
13.1 b) (Annealing test)	-
13.1 e) 1) (Physical tests for insulation: Tensile strength )	-
13.1 e) 1) (Physical tests for insulation: elongation at break )	-
13.1 e) 1) (Physical tests for Sheath : Tensile strength )	-
13.1 e) 1) (Physical tests for Sheath: elongation at break )	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : Tensile Strength )	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : Tensile Strength variation )	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : elongation variation at break)	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : elongation variation at break)	-
14.1 (Voltage test)	-
14.2 (Flammability test)	-
14.4 (Checking of overall diameter of cable)	-
15.1 (MANUFACTURER'S IDENTIFICATION)	-
16.2 (Marking )	-
16.2.1 (Standards Mark )	-

Partial

-
-

IS 5950 (1984)

Specification for shot firing cables (For Use Other Than In Shafts) (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Conductor : Material -IS : 8130-2013)	-
4.1 (Insulation : Material -IS : 5831-1984)	-
5.1 (Sheath : materail IS : 5831-1984)	-
6.1 (Conductor : Construction IS : 8130-2013)	-
7.1 (Insulation : Application )	-
7.2 (Thickness of Insulation - average )	-
7.2 (Thickness of Insulation - Min. )	-
7.3 (Colour of Insulation)	-
8.1 (Nominal radial thickness of sheath )	-
8.2 (Thickness of Sheath)	-
8.2 (Thickness of Sheath - min.)	-
8.3 (Colour of Sheath)	-
9.1 a) (Annealing test)	-
9.1 b) (Conductor resistance test)	-
9.1 d) i) (Insulation : Tensile strength)	-
9.1 d) i) (Insulation : elongation at break)	-
9.1 d) i) (Sheath : Tensile strength)	-
9.1 d) i) (Sheath : elongation at break)	-
9.1 d) ii) (Ageing in air oven - Insulation : Tensile strength)	-
9.1 d) ii) (Ageing in air oven - Insulation : Tensile strength Variation)	-
9.1 d) ii) (Ageing in air oven - Insulation : elongation at break)	-
9.1 d) ii) (Ageing in air oven - Insulation : elongation variation at break)	-
9.1 d) ii) (Ageing in air oven - Sheath : Tensile strength)	-
9.1 d) ii) (Ageing in air oven - Sheath : Tensile strength variation )	-
9.1 d) ii) (Ageing in air oven - Sheath : elongation at break)	-
9.1 d) ii) (Ageing in air oven - Sheath : elongation variation at break)	-
9.1 d) iii ) (Loss of mass test - insulation )	-
9.1 d) iii ) (Loss of mass test - Sheath )	-
9.1 d) iv ) (Hot deformation - insulation )	-
9.1 d) iv ) (Hot deformation - sheath )	-
9.1 d) v ) (Heat shock - insulation )	-
9.1 d) v ) (Heat shock - Sheath )	-
9.1 d) vi ) (Shrinkage - insulation )	-
9.1 d) vi ) (Shrinkage : Crack observed - insulation )	-
9.1 d) vi ) (Shrinkage - Sheath )	-
9.1 d) vi ) (Shrinkage: Crack observed - Sheath )	-
10.2 (Voltage test )	-
9.1 f) (Insulation resistance test: Volume resistivity )	-
9.1 f) (Insulation resistance test : IR constant)	-
10.4 (Flammability Test )	-
11.1 (Manufacturer’s Identification)	-
11.2 (Cable Code)	-
12.2 (Marking )	-
12.2.1 (Standard marks )	-

Partial

-
-

IS 318 (1981)

Specification for leaded tin bronze ingots and castings (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from defects-Ingots)	-
6.2 (Freedom from defects-Castings)	-
7.1 (Mass)	-
7.2 (Dimension)	-

Partial

-
-

IS 617 (1994)

Cast aluminium and its alloys - Ingots and castings for general engineering purposes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6, Table 2. (MECHANICAL PROPERTIES OF CASTINGS)	-
6.2 (Hardness)	-

Partial

-
-

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-

Partial

-
-

IS 2112 (2014)

Silver and silver alloys, jewellery/ artefacts - Fineness and marking - Specification (Third Revision)

upto 990 ppt

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Fineness)	-
5 (Cadmium)	-
5 (Lead)	-

Complete

-
-

IS 1741 (2019)

Latex Foam Rubber Products — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 and Annex F (COMPRESSION SET)	-
12 and Annex E (AGEING)	-
11 and Annex D (FLEXING TEST)	-
11 and Annex D (FLEXING TEST)	-
10.1 and Table 1 & 2 (DIMENSIONS -Thickness)	-
10.1 and Table 1 & 2 (DIMENSIONS -width)	-
10.1 and Table 1 & 2 (DIMENSIONS -Length)	-
9.0 (ODOUR)	-
8.0 (COLOUR)	-
7.3 (MATERIAL AND WORKMANSHIP)	-
7.2 (MATERIAL AND WORKMANSHIP)	-
7.1 (MATERIAL AND WORKMANSHIP)	-
7.1 (MATERIAL AND WORKMANSHIP)	-
5.1.1 (Indentation Hardness index)	-
5.1 (GRADES)	-
4.2 (SIZE AND SHAPE)	-
4.1 (TYPES)	-
Cl 14 (Manganese Content)	-
Cl 14 (Copper content)	-

Complete

-
-

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 Table-3 iv c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 Table-3 iv b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 Table-3 iv a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 Table-3 iii b (Setting Time Final)	-
7 Table-3 iii a (Setting Time Initial)	-
7 Table-3 ii b (Expansion by Autoclave)	-
7 Table-3 ii a (Expansion by Le Chatelier)	-
7 Table-3 i. (Fineness)	-
6.1 Table-2 viii (Alkali content)	-
6.1 Table-2 vii (Chloride content)	-
6.1 Table-2 vi (Loss on ignition)	-
6.1 Table-2 v (Total Sulphur Content calculated as Sulphuric Anhydride)	-
6.1 Table-2 iv (Magnesia)	-
6.1 Table-2 iii. (Insoluble residue)	-
6.1 Table-2 ii. (Ratio of percentage of alumina to that of iron oxide)	-
6.1 Table-2 i. (Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-

Partial

-
-

IS 5346 (1994)

Synthetic food colour - Preparations and mixtures - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.5 (Total dye Content)	-
Clause 4.6 Table 1 (Water InsoIuble matter,)	-
Clause 4.6 Table 1 (Lead (as pb) )	-
Clause 4.6 Table 1 (Arsenic(as As))	-
Clause 4.6 Table 1 (Heavy metals)	-

Partial

-
-

IS 15644 (2006)

Safety of electric toys

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.0 (Marking and instructions)	-
8.0 (Power Input)	-
9.0 (Heating and abnormal operation)	-
10.0 (Electrical strength at operating temperature)	-
11.1 (Moisture resistance)	-
11.2 (Resistant to humidity)	-
12.0 (Electric strength at room temperature)	-
13.0 (Mechanical strength)	-
14.1 (Construction)	-
14.2 (Construction)	-
14.3 (Construction)	-
14.4 (Construction)	-
14.5 (Construction)	-
14.6 (Construction)	-
14.7 (Construction)	-
14.8 (Construction)	-
14.9 (Construction)	-

Partial

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Office Laboratory (SROL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- [email protected]

Scope List

No Record Found

No Record Found

No Record Found