BIS - LIMS (Laboratory Information Management System)

UL INDIA PRIVATE LIMITED

Loc 1 & 2- Kalyani Platina Campus, Sy. no 129/4, EPIP Zone, Phase II, Whitefield, Bangalore- 560066, Bangalore, Bengaluru Urban, Karnataka, 560066

9986066622 [email protected]

Scope List

Reset

26 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 16169 (2019)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures (First Revision)

Solar Inverters

350000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6(Test for single or multi-phase inverter)	-	350000		-

Complete

12 May, 2024

-
-

IS 14286 : Part 1 : Sec 4 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 4 special requirements for testing of thin - Film Cu(In,ga)(S,se)2 based photovoltaic (Pv) modules (Second Revision)

Solar

1550000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.3(Insulation test (MQT 03))	-	6000	-
11.4(Measurement of temperature coefficients (MQT 04))	-	50000	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	50000	-
11.6(Performance at STC and NMOT (MQT 06))	-	15000	-
11.7(Performance at low irradiance (MQT 07))	-	8500	-
11.8(Outdoor exposure test (MQT 08))	-	50000	-
11.9(Hot-spot endurance test (MQT 09))	-	25000	-
11.1(UV preconditioning test (MQT 10))	-	80000	-
11.11(Thermal cycling test (MQT 11))	-	400000	-
11.12(Humidity-freeze test (MQT 12))	-	250000	-
11.13(Damp heat test (MQT 13))	-	420000	-
11.14(Robustness of terminations (MQT 14))	-	12000	-
11.15(Wet leakage current test (MQT 15))	-	15000	-
11.16(Static mechanical load test (MQT 16))	-	20000	-
11.17(Hail test (MQT 17))	-	20000	-
11.18(Bypass diode thermal test (MQT 18))	-	20000	-
11.19(Stabilization (MQT 19))	-	100000	-
11.1(Visual inspection (MQT 01))	-	2500	-
11.2(Maximum power determination (MQT 02))	-	6000	-

Complete

12 May, 2024

-
-

IS 14286 : Part 1 : Sec 3 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 3 special requirements for testing of thin - Film amorphous silicon based photovoltaic (Pv) modules (Second Revision)

Solar

1550000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1 IS 14286( Visual inspection)	-	2500	-
11.2 IS 14286( Maximum power determination)	-	6000	-
11.3 IS 14286( Insulation Test)	-	6000	-
11.4 IS 14286( Measurement of temperature coefficients)	-	50000	-
11.5 IS 14286( Measurement of nominal module operating temperature (NMOT))	-	50000	-
11.6 IS 14286( Performance at STC and NMOT)	-	15000	-
11.7 IS 14286( Performance at low irradiance)	-	8500	-
11.8 IS 14286( Outdoor exposure Test)	-	50000	-
11.9 IS 14286( Hot-spot endurance test)	-	25000	-
11.10 IS 14286( UV Preconditioning test )	-	80000	-
11.11 IS 14286( Thermal cycling test)	-	400000	-
11.12 IS 14286( Humidity-freeze test)	-	250000	-
11.13 IS 14286(Damp heat test)	-	420000	-
11.14, Table 1 IS 14286( Robutness of terminations test - Retention of Junction Box on Mounting Surface - Test of Cord Anchorage)	-	12000	-
11.15 IS 14286( Wet leakage current test)	-	15000	-
11.16 IS 14286( Static Mechanical load test)	-	20000	-
11.17, Table 3 & 4, IS 14286( Hail test)	-	20000	-
11.18 IS 14286( Bypass diode testing)	-	20000	-
11.19(Stabilization (MQT 19))	-	100000	-

Complete

12 May, 2024

-
-

IS 14286 : Part 1 : Sec 2 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 2 special requirements for testing of thin - Film cadmium telluride (CdTe) based photovoltaic (Pv) modules (Second Revision)

Solar

1550000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1 IS 14286( Visual inspection)	-	2500	-
11.2 IS 14286( Maximum power determination)	-	6000	-
11.3 IS 14286( Insulation Test)	-	6000	-
11.4 IS 14286( Measurement of temperature coefficients)	-	50000	-
11.5 IS 14286( Measurement of nominal module operating temperature (NMOT))	-	50000	-
11.6 IS 14286( Performance at STC and NMOT)	-	15000	-
11.7 IS 14286( Performance at low irradiance)	-	8500	-
11.8 IS 14286( Outdoor exposure Test)	-	50000	-
11.9 IS 14286( Hot-spot endurance test)	-	25000	-
11.10 IS 14286( UV Preconditioning test )	-	80000	-
11.11 IS 14286( Thermal cycling test)	-	400000	-
11.12 IS 14286( Humidity-freeze test)	-	250000	-
11.13 IS 14286(Damp heat test)	-	420000	-
11.14, Table 1 IS 14286( Robutness of terminations test - Retention of Junction Box on Mounting Surface - Test of Cord Anchorage)	-	12000	-
11.15 IS 14286( Wet leakage current test)	-	15000	-
11.16 IS 14286( Static Mechanical load test)	-	20000	-
11.17, Table 3 & 4, IS 14286( Hail test)	-	20000	-
11.18(Bypass diode thermal test (MQT 18))	-	20000	-
11.19(Stabilization (MQT 19))	-	100000	-

Complete

12 May, 2024

-
-

IS 14286 : Part 1 : Sec 1 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 1 special requirements for testing of crystalline silicon photovoltaic (Pv) modules (Second Revision)

Solar

1500000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(Visual inspection (MQT 01))	-	2500	-
11.2(Maximum power determination (MQT 02))	-	6000	-
11.3(Insulation test (MQT 03))	-	6000	-
11.4(Measurement of temperature coefficients (MQT 04))	-	50000	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	50000	-
11.6(Performance at STC and NMOT (MQT 06))	-	15000	-
11.7(Performance at low irradiance (MQT 07))	-	8500	-
11.8(Outdoor exposure test (MQT 08))	-	50000	-
11.9(Hot-spot endurance test (MQT 09))	-	25000	-
11.1(UV preconditioning test (MQT 10))	-	80000	-
11.11(Thermal cycling test (MQT 11))	-	400000	-
11.12(Humidity-freeze test (MQT 12))	-	250000	-
11.13(Damp heat test (MQT 13))	-	420000	-
11.14(Robustness of terminations (MQT 14))	-	12000	-
11.15(Wet leakage current test (MQT 15))	-	15000	-
11.16(Static mechanical load test (MQT 16))	-	20000	-
11.17(Hail test (MQT 17))	-	20000	-
11.18(Bypass diode thermal test (MQT 18))	-	20000	-
11.19(Stabilization (MQT 19))	-	50000	-

Complete

12 May, 2024

-
-

IS 16221 : Part 1 (2016)

Safety of Power Converters for use in Photovoltaic Power Systems Part 1 General Requirements

1400612 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.5(Humidity preconditioning)	-	130000	-
4.6(Backfeed voltage protection)	-	350600	-
4.7(Electrical rating tests)	-	30000	-
7(Protection against electric shock and energy hazards)	-	812012	-
12(Chemical hazards)	-	78000	-
4.3, 4.3.2, 4.3.2.2, 4.3.2.3(Thermal Tests (Maximum temperatures, Touch temperature, temperature limits for mount surfaces))	-	-	-
4.4.3.1(Protection against shock hazard)	-	-	-
4.4.3.2(Protection against spread of fire)	-	-	-
4.4.3.4(Protection Against parts expulsion hazards)	-	-	-
4.4.4.1(Component fault tests)	-	-	-
4.4.4.2(Equipment’s or parts for short-term or intermittent operation)	-	-	-
4.4.4.3(Motors(Lock rotor))	-	-	-
4.4.4.4(Transformer short circuit tests)	-	-	-
4.4.4.5(Output short circuit)	-	-	-
4.4.4.6(Backfeed current test for equipment with more than one source of supply)	-	-	-
4.4.4.7(Output overload)	-	-	-
4.4.4.8(Cooling system failure)	-	-	-
4.4.4.9(Heating devices)	-	-	-
4.4.4.10(Safety interlock systems)	-	-	-
4.4.4.11(Reverse d.c. connections)	-	-	-
4.4.4.12(Voltage selector mismatch)	-	-	-
4.4.4.13(Mis-wiring with incorrect phase sequence or polarity)	-	-	-
4.4.4.14(Printed wiring board short-circuit test)	-	-	-
4.6.1(Backfeed tests under normal conditions)	-	-	-
4.6.2(Backfeed tests under single-fault conditions)	-	-	-
5.1.2(Durability of markings)	-	-	-
5.2.1(Visibility and legibility requirements for warning markings)	-	-	-
6.3(Ingress protection)	-	-	-
7.3.2.3(Short-term limits of accessible voltages under fault conditions)	-	-	-
7.3.2.6(Working voltage and DVC)	-	-	-
7.3.4,7.3.4.2(protection against direct contact)	-	-	-
7.3.4.3(Protection by means of insulation of live parts)	-	-	-
7.3.5,7.3.5.2(Protection in case of direct contact)	-	-	-
7.3.5.3.1(Limitation of current through protective impedance)	-	-	-
7.3.5.3.2(Limitation of discharging energy through protective impedance)	-	-	-
7.3.5.4(Protection by means of limited voltages)	-	-	-
7.3.6.1,7.3.6.2(Protection against indirect contact(Creapage & clearance))	-	-	-
7.3.6.3(Protective class I - Protective bonding and earthing)	-	-	-
7.3.6.3.3(Rating of protective bonding)	-	-	-
7.3.7.8.4.2(Use of coating materials (on PWBs))	-	-	-
7.3.7.4(Clearance distances)	-	-	-
7.3.7.5(Creepage distances)	-	-	-
7.3.8(Residual current detection (RCD) or Monitoring (RCM) device compatibilty (DC components on AC side))	-	-	-
7.3.9(Protection against shock hazard due to stored energy)	-	-	-
7.4(Protection against energy hazards)	-	-	-
7.5.1(Impulse voltage test (type test))	-	-	-
7.5.2(Voltage test (dielectric strength test))	-	-	-
7.5.2.3(Humidity preconditioning)	-	-	-
7.5.3(Partial discharge test (type test or sample test))	-	-	-
7.5.4(Touch current measurement)	-	-	-
8.2(Moving parts)	-	-	-
8.3(Stability)	-	-	-
8.4(Provisions for lifting and carrying)	-	-	-
8.5(Wall mounting)	-	-	-
9.1.1(Reducing the risk of ignition and spread of flame)	-	-	-
9.1.2(Conditions for a fire enclosure)	-	-	-
9.1.3(Material requirements for protection against fire hazard)	-	-	-
9.1.4(Openings in fire enclosures)	-	-	-
9.1.4.6(Additional requirements for openings in transportable equipment)	-	-	-
9.2.2(Limited power source tests)	-	-	-
9.3(Short-circuit and overcurrent protection)	-	-	-
10.2(Sonic pressure and sound level)	-	-	-
11.1(Liquid containment, pressure and leakage)	-	-	-
13.1(Handles and manual controls)	-	-	-
13.1.1(Adjustable controls)	-	-	-
13.2(Securing of parts)	-	-	-
13.3(Provisions for external connections)	-	-	-
13.4(Internal wiring and connections)	-	-	-
13.5(Openings in enclosures)	-	-	-
13.3.2.5(Cord anchorages and strain relief)	-	-	-
13.3.5(Wire bending space for wires 10mm2 and greater)	-	-	-
13.5(Openings in enclosures)	-	-	-
13.6.2.1(Stress relief test)	-	-	-
13.7(Mechanical resistance to deflection, impact, or drop)	-	-	-
13.8(Thickness requirements for metal enclosures)	-	-	-
14.2(Motor over-temperature protection)	-	-	-
14.3(Over-temperature protection devices)	-	-	-
14.7(Circuits or components used as transient overvoltage limiting devices)	-	-	-

Complete

12 May, 2024

-
-

IS 16169 (2014)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures

Photovoltaic (PV) Inverter(s)

320000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 to 6.2, (Elec)(Test for single or multi-phase inverter to Pass/fail criteria)	-	320000		-

Complete

12 May, 2024

-
-

IS/IEC 61730 : PART 2 (2004)

Photovoltaic (PV) Module Safety Qualification Part 2 Requirements for Testing

CRYSTALLINE SILICON TERRESTRIAL PHOTOVOLTAIC (PV) MODUL

840000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Visual Inspection (MST 01))	-	2000	-
10.2(Accessibility test (MST 11))	-	4000	-
10.3(Cut susceptibility test (MST 12))	-	4000	-
10.4(Ground Continuity Test (MST 13))	-	4000	-
10.5(Impulse voltage test (MST 14))	-	20000	-
10.6(Dielectric withstand test (MST 16))	-	5000	-
10.7(Temperature test (MST 21))	-	10000	-
10.8(Fire test (MST 23))	-	50000	-
10.9(Reverse Current overload test (MST 26))	-	10000	-
10.10(Module breakage test (MST 32))	-	10000	-
11.1(Partial discharge-test (MST 15))	-	15000	-
Cl.5, Table 7(Hot spot test (MST 22))	-	15000	-
Cl.5, Table 7(UV resistance (MST 54))	-	35000	-
Cl.5, Table 7(Humidity freeze (10HF) (MST 52))	-	150000	-
Cl.5, Table 7(Damp heat (DH1000) (MST 53))	-	230000	-
Cl.5, Table 7(Wet leakage current test (MST 17))	-	7000	-
Cl.5, Table 7(Robustness of termination test (MST 42))	-	5000	-
Cl.5, Table 7(Mechanical load test (MST 34))	-	10000	-
Cl.5, Table 7(Thermal cycling (T200) (MST 51))	-	230000	-
Cl.5, Table 7(Thermal cycling (T50) (MST 51))	-	24000	-

Complete

12 May, 2024

-
-

IS/IEC 61730 : PART 1 (2004)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction

PV Modules

100000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Polymeric materials)	-	10000	-
6(Internal wiring and current-carrying parts)	-	10000	-
7(Connections)	-	10000	-
8(Bonding and grounding)	-	10000	-
9(Creepage and clearance distances)	-	50000	-
10(Field wiring compartments with covers)	-	10000	-

Complete

12 May, 2024

-
-

IS/IEC 61730 : PART 1 (2016)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction ( First Revision )

PV Modules

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	50000		-

Complete

12 May, 2024

-
-

IS/IEC 61730 : PART 2 (2019)

Photovoltaic (PV) module safety qualification: Part 2 requirements for testing (First Revision)

CRYSTALLINE SILICON TERRESTRIAL PHOTOVOLTAIC (PV) MODUL

1900000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.2 IS/IEC 61730-2( Visual inspection MST01)	-	2500	-
10.3 IS/IEC 61730-2(Performance at STC MST 02)	-	5500	-
10.4 IS/IEC 61730-2(Maximum power determination MST 03)	-	5500	-
10.5 IS/IEC 61730-2(Insulation thickness test MST 04)	-	10000	-
10.6 IS/IEC 61730-2(Durability of marking MST 05)	-	5500	-
10.7 IS/IEC 61730-2(Sharp edge test MST 06)	-	6000	-
10.8 IS/IEC 61730-2(Bypass diode functionality test MST 07)	-	7000	-
10.9 IS/IEC 61730-2(Accessibility test MST 11)	-	15000	-
10.10 IS/IEC 61730-2(Cut susceptibility test MST 12)	-	15000	-
10.11 IS/IEC 61730-2(Continuity test of equipotential bonding MST 13)	-	15000	-
10.12 IS/IEC 61730-2(Impulse voltage test MST 14)	-	70000	-
10.13 IS/IEC 61730-2( Insulation test MST 16)	-	6000	-
10.14 IS/IEC 61730-2( Wet leakage current test MST 17)	-	15000	-
10.15 IS/IEC 61730-2( Temperature test MST 21)	-	35000	-
10.16 IS/IEC 61730-2(Hot-spot endurance test MST 22)	-	25000	-
10.17 IS/IEC 61730-2( Fire test MST 23)	-	250000	-
10.18 IS/IEC 61730-2(Ignitability test MST 24)	-	80000	-
10.19 IS/IEC 61730-2( Bypass diode thermal test MST 25)	-	20000	-
10.20 IS/IEC 61730-2( Reverse current overload test MST 25)	-	15000	-
10.21 IS/IEC 61730-2( Module breakage test MST 32)	-	10000	-
10.22 IS/IEC 61730-2(Screw connections test MST 33)	-	5000	-
10.23 IS/IEC 61730-2( Static Mechanical load test MST 34)	-	20000	-
10.24 IS/IEC 61730-2( Peel test MST 35)	-	100000	-
10.25 IS/IEC 61730-2( Lap shear strength test MST 36)	-	250000	-
10.26 IS/IEC 61730-2(Materials creep test MST 37)	-	350000	-
10.27 IS/IEC 61730-2( Robutness of terminations test MST 42)	-	12000	-
10.28 IS/IEC 61730-2(Thermal cycling test MST 51)	-	400000	-
10.29 IS/IEC 61730-2( Humidity-freeze test MST 52)	-	250000	-
10.30 IS/IEC 61730-2( Damp heat test MST 53)	-	400000	-
10.31 IS/IEC 61730-2(UV test MST 54)	-	200000	-
10.32 IS/IEC 61730-2( Cold conditioning MST 55)	-	40000	-
10.33 IS/IEC 61730-2( Dry heat conditioning MST 56)	-	350000	-

Complete

12 May, 2024

-
-

IS 16333 : Part 3 (2017)

Mobile phone handsets: Part 3 indian language support for mobile phone handsets - Specific requirements (First Revision)

38000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1(Inputting of text)	-	18000		-
5.2(Message Readability)	-	20000		-

Complete

12 May, 2024

-
-

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

170000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Protection from electric shock and energy hazards)	-	1000	-
2.2(SELV circuits)	-	2000	-
2.3(TNV circuits)	-	5000	-
2.5(Limited power sources .)	-	3000	-
2.8(Safety interlocks)	-	3000	-
2.10(Clearances, creepage distances and distances through insulation)	-	3000	-
3.3(Wiring terminals for connection of external conductors)	-	1000	-
4.1(Stability)	-	1000	-
4.4(Protection against hazardous moving parts)	-	500	-
4.5(Thermal requirements)	-	3000	-
4.7(Resistance to fire)	-	4000	-
5.1(Touch current and protective conductor curren)	-	3000	-
5.2(Electric strength)	-	3000	-
5.3(Abnormal operating and fault conditions)	-	5000	-
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	3000	-
6.3(Protection of the telecommunication wiring system from overheating)	-	3500	-
1.6(Power interface .)	-	10000	-
1.7(Markings and instructions)	-	1000	-
4.2(Mechanical strength)	-	18000	-
2.6(Provisions for earthing and bonding)	-	2000	-

Complete

12 May, 2024

-
-

IS 14286 (2010)

Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval (First Revision)

CRYSTALLINE SILICON TERRESTRIAL PHOTOVOLTAIC (PV) MODUL

800000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Visual inspection)	-	2000	-
10.2(Maximum power determination)	-	4000	-
10.3(Insulation test)	-	4000	-
10.5(Measurement of NOCT)	-	30000	-
10.6(Performance at STC and NOCT)	-	9000	-
10.7(Performance at low irradiance)	-	4000	-
10.8(Outdoor exposure test)	-	20000	-
10.9(Hot-spot endurance test)	-	15000	-
10.10(UV preconditioning)	-	35000	-
10.11(Thermal cycling test)	-	230000	-
10.12(Humidity freeze test)	-	150000	-
10.13(Damp heat test)	-	230000	-
10.14(Robustness of termination test)	-	10000	-
10.15(Wet leakage current test)	-	7000	-
10.16(Mechanical load test)	-	10000	-
10.17(Hail test)	-	10000	-
10.18(Bypass diode thermal' test)	-	10000	-
10.4(Measurement of temperature coefficients)	-	20000	-

Complete

12 May, 2024

-
-

IS/IEC 61701 (2011)

Salt mist corrosion testing of photovoltaic (PV) modules

- View breakup
(i) Severity 1-Rs.3,50,000/- (ii) Severity 3-Rs.2,00,000/- (iii)Severity 4-Rs.4,50,000/- (iv)Severity 5-Rs.6,00,000/- (v) Severity 6-Rs.7,50,000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

12 May, 2024

-
-

IS 16077 (2013)

Thin - Film terrestrial photovoltaic (PV) modules - Design qualification and type approval

920000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Visual inspection)	-	2000	-
10.2(Maximum power determination)	-	4000	-
10.3(Insulation test)	-	4000	-
10.4(Measurement of temperature coefficients)	-	25000	-
10.5(Measurement of NOCT)	-	40000	-
10.6(Performance at STC and NOCT)	-	10000	-
10.7(Performance at low irradiance)	-	5000	-
10.8(Outdoor exposure test)	-	20000	-
10.9(Hot-spot endurance test)	-	25000	-
10.10(UV preconditioning)	-	35000	-
10.11(Thermal cycling test)	-	240000	-
10.12(Humidity freeze test)	-	200000	-
10.13(Damp heat test)	-	240000	-
10.14(Robustness of termination test)	-	10000	-
10.15(Wet leakage current test)	-	10000	-
10.16(Mechanical load test)	-	10000	-
10.17(Hail test)	-	10000	-
10.18(Bypass diode thermal' test)	-	10000	-
10.19(Light Soaking)	-	20000	-

Complete

12 May, 2024

-
-

IS 16170 : Part 1 (2014)

Photovoltaic (PV) module performance testing and energy rating: Part 1 irradiance and temperature performance measurements and power rating

- View breakup
Rs.7,50,000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

12 May, 2024

-
-

IS 16046 (2015)

Secondary Cells and Batteries Containing Alkaline or Other Non-acid Electrolytes - Safety Requirements for Portable Sealed Secondary Cells, and for Batteries Made from them, for Use in Portable Applications ( First Revision )

- View breakup
Rs.4,00,000/- for Nickel/Lithium Cells, Rs.325000/- for Lithium Battery Pack, Rs.340000/- for Nickel Battery pack

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

12 May, 2024

-
-

IS 16221 : Part 2 (2015)

Safety of power converters for use in photovoltaic power systems: Part 2 particular requirements for inverters

1585946 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and documentation)	-	7500	-
7(Protection against electric shock and energy hazards)	-	560000	-
8(Protection against Mechanical Hazards)	-	179000	-
9(Protection against Fire Hazards)	-	660000	-
10(Protection against Sonic Pressure Hazards)	-	47111	-
13(Physical Requirements)	-	132335	-
4.4.4.15.1(Fault-tolerance of residual current monitoring)	-	-	-
4.4.4.15.2(Fault-tolerance of automatic disconnecting means)	-	-	-
4.4.4.16(Stand-alone inverters – Load transfer test)	-	-	-
4.4.4.17(Cooling system failure – Blanketing test)	-	-	-
4.7.3(Measurement requirements for AC output ports for stand-alone inverters)	-	-	-
4.7.4(Stand-alone Inverter AC output voltage and frequency)	-	-	-
4.7.4.2(Steady state output voltage at nominal DC input)	-	-	-
4.7.4.3(Steady state output voltage across the DC input range)	-	-	-
4.7.4.4(Load step response of the output voltage at nominal DC input)	-	-	-
4.7.4.5(Steady state output frequency)	-	-	-
4.7.5(Stand-alone inverter output voltage waveform)	-	-	-
4.7.5.2(Sinusoidal output voltage waveform requirements)	-	-	-
4.7.5.3(Non-sinusoidal output waveform requirements)	-	-	-
4.7.5.5(Output voltage waveform requirements for inverters for dedicated loads)	-	-	-
4.8.2.1(Array insulation resistance detection for inverters for ungrounded arrays)	-	-	-
4.8.2.2(Array insulation resistance detection for inverters for functionally grounded arrays)	-	-	-
4.8.3.2(30 mA touch current type test for isolated inverters)	-	-	-
4,8.3.3(Fire hazard residual current type test for isolated inverters)	-	-	-
4.8.3.5(Protection by residual current monitoring)	-	-	-
7.3.10(Additional requirements for stand-alone inverters)	-	-	-
9.3.4(Inverter backfeed current onto the array)	-	-	-

Complete

12 May, 2024

-
-

IS 1293 (2005)

Plugs and socket- outlets of rated voltage up to and including 250 volts and rated current up to 16 amperes

Plug

180000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	2000	-
7(Heating under normal operating conditions)	-	17000	-
8(Constructional requirements with regard to the protection against electric shock)	-	5000	-
9(Electric shock hazard under normal operating conditions)	-	18000	-
11(Fault conditions)	-	12000	-
12(Mechanical strength)	-	14000	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	12000	-
15(TERMINALS)	-	8000	-
16(External flexible cords)	-	5000	-
17(Electrical connections and mechanical fixings)	-	5000	-
19(Stability and mechanical hazards)	-	12000	-
20(Resistance to fire)	-	18000	-

Complete

12 May, 2024

-
-

IS 16046 : Part 1 (2018)

Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 1 Nickel Systems ( Second Revision )

192000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Insulation and Wiring)	-	2000	-
7.1(Charging procedure for test purposes)	-	7000	-
5.3(Venting)	-	2000	-

Complete

12 May, 2024

-
-

IS 16046 : Part 2 (2018)

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Insulation and Wiring)	-	15000	-
7.1(Charging procedure for test purposes)	-	35000	-
5.1(General)	-	0	-
5.3(Venting)	-	0	-
7.2(Intended Use)	-	35000	-
7.3(Reasonably foreseeable misuse)	-	215000	-

Complete

12 May, 2024

-
-

IS/IEC 61683 (1999)

Photovoltaic systems - Power conditioners - Procedure for measuring efficiency

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Efficiency calculations)	-	55000	-
6(Efficiency test circuits)	-	55000	-
7(Loss measurement)	-	10000	-
4(Efficiency measurement conditions)	-	-	-

Complete

12 May, 2024

-
-

IS/IEC 60898 : PART 1 (2015)

Electrical accessories - Circuit - Breakers for overcurrent protection for household and similar installations: Part 1 circuit - Breakers for a.c. operation (First Revision)

MCB

611940 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking and other product information, IS 60898-1)	-	500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.1(General, IS 60898-1)	-	500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.2(Mechanism, IS 60898-1)	-	500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.3(Test of indelibility of marking, IS 60898-1)	-	800	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.3(Clearances and creepage distances, IS 60898-1)	-	850	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.4(Test of reliability of screws, current-carrying parts and connections, IS 60898-1)	-	3000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.5.1(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	3500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.6(Test of protection against electric shock, IS 60898-1)	-	1540	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.3(Clearances and creepage distances, IS 60898-1)	-	850	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.14.3(Test of resistance to heat, IS 60898-1)	-	1000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.16(Test of resistance to rusting)	-	1500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.15(Resistance to abnormal heat and to fire)	-	20000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-15000 SPN/DP-15000 TP/TPN-20000 FP-20000
9.7.5.4(Test of protection against electric shock, IS 60898-1)	-	12500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-8000 SPN/DP-10000 TP/TPN-10000 FP-12500
9.7.1(Test of protection against electric shock, IS 60898-1)	-	15000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.7.2(Test of protection against electric shock, IS 60898-1)	-	7500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-5000 TP/TPN-5000 FP-7500
9.7.3(Test of protection against electric shock, IS 60898-1)	-	7500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-5000 TP/TPN-5000 FP-7500
9.7.4(Test of protection against electric shock, IS 60898-1)	-	7500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-5000 TP/TPN-5000 FP-7500
9.7.5.2(Test of protection against electric shock, IS 60898-1)	-	12000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-8000 SPN/DP-10000 TP/TPN-10000 FP-12000
9.8(Test of temperature-rise and measurement of power loss, IS 60898-1)	-	18000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-13000 SPN/DP-15000 TP/TPN-15000 FP-18000
9.9(28- day test, IS 60898-1)	-	30000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-28000 SPN/DP-30000 TP/TPN-30000 FP-30000
9.11(Verification of mechanical and electrical endurance, IS 60898-1)	-	25000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-23000 SPN/DP-23000 TP/TPN-25000 FP-25000
9.12(Short- Circuit tests, IS 60898-1)	-	57000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-40000 SPN/DP-40000 TP/TPN-57000 FP-57000
9.13.1(Mechanical Stress, IS 60898-1)	-	9000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-6800 TP/TPN-8000 FP-9000
8.1.6(Non-interchangeability)	-	1000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.12.12(Verification of the circuit-breaker after short-circuit tests)	-	6000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 4000/- for SP, SPN and DP 6000/- TP, TPN and FP
9.12.11.2.2(Short-circuit test for verifying the suitability of circuit-breakers for use in IT systems)	-	45800	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 26900/- for SP, SPN, DP 45800/- for TP, TPN, FP
9.5.2(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	1000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.5.3(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	1250	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.5.4(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	1250	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.14.1(Test of resistance to heat, IS 60898-1)	-	300	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.14.2(Test of resistance to heat, IS 60898-1)	-	350	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.10.2(Test of tripping characteristic, IS 60898-1)	-	12000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 7500/- for SP 10000/- for SPN, DP, TP, TPN 12000/- for FP
9.10.3(Test of tripping characteristic, IS 60898-1)	-	12000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 7500/- for SP 10000/- for SPN, DP, TP, TPN 12000/- for FP
9.10.4(Test of tripping characteristic, IS 60898-1)	-	8000	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 6000/- for SPN, DP, TP, TPN 8000/- for FP
9.10.5(Test of tripping characteristic, IS 60898-1)	-	14700	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 8300/- for SP 12300/- for SPN, DP, TP, TPN 14700/- for FP
9.13.2.2(Mechanical Stress, IS 60898-1)	-	3500	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 2000/- for SP 2500/- for SPN, DP 3000/- for TP, TPN 3500/- for FP
9.13.2.3(Mechanical Stress, IS 60898-1)	-	200	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.13.2.4(Mechanical Stress, IS 60898-1)	-	1600	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 1000/- for SP 1200/- for SPN, DP 1400/- for TP, TPN 1600/- for FP
9.13.2.5(Mechanical Stress, IS 60898-1)	-	200	Complete testing charges-384740 (For 3 samples of SP), 468440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)

Complete

12 May, 2024

-
-

IS 12640 : Part 2 (2016)

Residual current operated circuit - Breakers with integral overcurrent protection for household and similar uses (Rcbos): Part 2 general rules

RCBO

1775000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.3(Clearances and creepage distances (internal parts))	-	1500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-1000 FP-1500
9.7.1(Resistance to humidity)	-	15000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP)
9.7.2(Insulation resistance of main circuit)	-	7500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-5000 FP-7500
9.7.3 a)(Dielectric strength of the main circuit)	-	7500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-5000 FP-7500
9.7.6(Capability of control circuits connected to the main circuit in respect of withstanding high d.c. voltages due to insulation measurements )	-	11000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-10000 FP-11000
9.8(Test of temperature-rise )	-	18000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-15000 FP-18000
9.22.2(Test with temperature of 40 ºC)	-	38000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-30000 FP-38000
9.12.11.2(PERFORMANCE AT REDUCED SHORT-CIRCUIT CURRENTS)	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-70000 FP-90000
9.12.12.1(VERIFICATION OF THE RCBO AFTER SHORT-CIRCUIT TEST : DIELECTRIC STRENGTH TEST)	-	110000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-80000 FP-110000
9.9.1.2(Verification of the operating characteristic under residual current conditions)	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-60000 FP-90000
9.16(Verification of the operation of the test device at the limits of rated voltage )	-	4000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-3000 FP-4000
9.13.1(Verification of resistance to mechanical shock )	-	11000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-9000 FP-11000
9.12.11.3(SHORT-CIRCUIT PERFORMANCE AT 1500 A)	-	139000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-101000 FP-139000
9.12.11.4(TEST AT SERVICE SHORT-CIRCUIT CAPACITY (Ics)	-	120000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-90000 FP-120000
9.22.1(Reliability (Climatic test))	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-90000 FP-90000
9.19.1(Current surge test for all RCBOs (0,5 µs/100 kHz ring wave test))	-	16000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-12000 FP-16000
6, 9.3(Indelibility of marking)	-	-	-
8.1.2 , 9.11(Trip-free mechanism)	-	-	-
9.4(Reliability of screws, current-carrying parts and connections)	-	-	-
9.5(Test of reliability of screw-type terminals for external)	-	-	-
9.6(Protection against electric shock)	-	-	-
9.14(Resistance to heat)	-	-	-
9.25(Resistance to rusting)	-	-	-
9.15(Resistance to abnormal heat and to fire)	-	-	-
9.7.7.4(Resistance of the insulation of open contacts and basic insulation against an impulse voltage in normal conditions)	-	-	-
9.7.7.5(Verification of the behavior of components bridging the basic insulation)	-	-	-
9.7.4(Insulation resistance and dielectric strength of auxiliary circuits)	-	-	-
9.7.7.1(testing procedure for the impulse withstand voltage tests)	-	-	-
9.7.7.2(Verification of clearances with the impulse withstand voltage)	-	-	-
9.7.5(Secondary circuit of detection transformers)	-	-	-
9.7.7.3(Verification of leakage currents across open contacts)	-	-	-
9.23(Ageing of electronic components)	-	-	-
9.10(Mechanical and electrical endurance)	-	-	-
9.17(Behaviour in case of failure of the line voltage)	-	-	-
9.19(Behaviour in case of surge currents)	-	-	-
9.21(DC components)	-	-	-
9.12.13(Performance at IΔm)	-	-	-
9.9.2(Overcurrent operating characteristics)	-	-	-
9.12.11.4 b) (and 9.12.12)(Performance at service short-circuit capacity)	-	-	-
9.12.11.4 c) (and 9.12.12.2)(Performance at rated short-circuit capacity)	-	-	-
9.24 Annex-A, Test Sequence-H(Surges)	-	-	-
9.24 Annex-A, Test Sequence-I(Conducted sine-wave form voltages or currents)	-	-	-
9.24 Annex-A, Test Sequence-I(Radiated electromagnetic field)	-	-	-
9.24 Annex-A, Test Sequence-I(Fast transients (bursts))	-	-	-
9.24 Annex-A, Test Sequence-J(Conducted common mode disturbances)	-	-	-
9.24 Annex-A, Test Sequence-J(Electrostatic discharges)	-	-	-

Complete

12 May, 2024

-
-

IS 12640 : Part 1 (2016)

Residual current operated circuitBreakers without integral overcurrent protection for household and similar uses (Rccbs): Part 1 general rules (Second Revision)

RCCB

1545000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking)	-	500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
8.1.1(General)	-	500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
8.1.2(Mechanism)	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
9.3(Indelibility of marking)	-	1000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
8.1.3 (Creepage distances)	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
8.1.3 i)(Clearance )	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
9.15(Trip-free mechanism)	-	3500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2500 FP-3500
9.4(Test of reliability of screws, current carrying parts and connections )	-	5000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-3000 FP-5000
9.5(Test of reliability of terminals for external conductors)	-	5500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-3500 FP-5500
9.6(Protection against electric shock)	-	4000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-4000
9.13(Test of resistance to heat)	-	2500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-2500
8.1.3(Clearances and creepage distances (internal parts) Clearances distances)	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
9.7.1(Dielectric Properties : Resistance to humidity)	-	15000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.2 (Insulation resistance of main circuit)	-	7500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-5000 FP-7500
9.7.7.1(Rated impulse withstand voltage)	-	13500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-11000 FP-13500
9.8(Test of Temperature rise)	-	18000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-15000 FP-18000
9.22.2(Testing with temperature of 40)	-	38000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-30000 FP-38000
9.23(Verification of ageing of electronic components )	-	25500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-23000 FP-25500
9.11.2.3(VERIFICATION OF PERFORMANCE AT Im)	-	60000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-49000 FP-60000
9.16 a)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-3000
9.16 b)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-3000
9.16 c)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-3000
9.12.1(Verification of resistance to mechanical shock)	-	11000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-9000 FP-11000
9.18.1(Verification of the limiting value of overcurrent in case of a load through an RCCB with two current paths)	-	11000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-9000 FP-11000
9.11.2.4 (Verification of the coordination between the RCCB and the SCPD)	-	75000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-60000 FP-75000
9.22.1(Climatic test)	-	90000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.19.1( Verification of behaviour of RCCBs in case of current surges caused by impulse voltages (Current surge test for all RCCBs (0,5 µs/100 kHz ring wave test)))	-	16000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-12000 FP-16000
9.19.2(Verification of behaviour at surge currents up to 3000A (8/20 s surge current test))	-	16000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-12000 FP-16000

Complete

12 May, 2024

-
-

Bureau of Indian Standards

The National Standards Body of India

UL INDIA PRIVATE LIMITED

Loc 1 & 2- Kalyani Platina Campus, Sy. no 129/4, EPIP Zone, Phase II, Whitefield, Bangalore- 560066, Bangalore, Bengaluru Urban, Karnataka, 560066

9986066622 [email protected]

Scope List

No Record Found

No Record Found

No Record Found