BIS - LIMS (Laboratory Information Management System)

Hindustaan Test House

Plot No. 36,Sector 1, HSIIDC IGC Saha, Ambala Cantt, Ambala Cantt, Ambala, Haryana, 133104

9355002828 [email protected]

Scope List

Reset

27 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 10701 (2012)

Structural plywood - Specification (First Revision)

17650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 11.2(Moisture content)	-	400	20% discount for BIS
11.3(Glue Shear strength in dry state)	-	1000	20% discount for BIS
11.4.1(Resistance to Water)	-	2500	20% discount for BIS
11.5(Resistance to Micro-organisms)	-	2800	20% discount for BIS
11.6(Tensile Strength)	-	1000	20% discount for BIS
11.7.1(Compressive Strength, Bending Strength, Panel Shear Strength, Plate Shear Strength and Rolling Shear Strngth)	-	6150	20% discount for BIS
11.8(Wet Bending Strength)	-	2000	20% discount for BIS (Retention of preservative-1000)

Complete

12 Sep, 2022

-
-

IS 12894 (2002)

Pulverized fuel ash - Lime bricks - Specification

All

7250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General Requirements)	-	100	20% discount for BIS
3.2(General Requirements)	-	200	-
3.3(General Requirements)	-	0	-
3.4(General Requirements)	-	100	-
3.5(General Requirements)	-	100	20% discount for BIS
5.1(Dimensions)	-	1000	20% discount for BIS
7.1, Table -1(Average Wet Compressive Strength)	-	1500	20% discount for BIS
7.2(Drying Shrinkage)	-	1500	20% discount for BIS
7.3(Efflorescence Test)	-	2000	20% discount for BIS
7.4(Water Absorption)	-	750	20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 13757 (1993)

Burnt Clay Fly Ash Building Bricks-specification

All

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(GENERAL QUALITY)	-	500	20% discount for BIS
6.1(Dimensions)	-	1000	20% discount for BIS
6.2(Tolerances)	-	0	-
7.1(Compressive Strength)	-	1500	20% discount for BIS
7.2(Water Absorption)	-	750	20% discount for BIS
7.3(Efforescence)	-	2000	20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 16720 (2018)

Pulverized Fuel Ash-Cement Bricks- Specification

All

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 and fig.1A &1B(Dimensions- Length (L) )	-	300	20% discount for BIS
4.1 and fig.1A &1B(Dimensions- Width (B) )	-	300	20% discount for BIS
4.1 and fig.1A &1B(Dimensions- Height (H))	-	300	20% discount for BIS
4.1 & 4.3 and fig.1A &1B(Dimensions - Depth)	-	100	20% discount for BIS
4.1 and fig.1A &1B(Dimensions)	-	0	-
5 and Tanle 1 (CLASSIFICATION)	-	0	-
8.1(GENERAL)	-	500	20% discount for BIS
8.3(Density Annex C of IS 2185 (Part 1))	-	500	20% discount for BIS
8.4 and Table 1(Compressive Strength - Individual IS 3495 (Part 1))	-	1500	20% discount for BIS
8.5(Drying Shrinkage IS 4139)	-	1500	20% discount for BIS
8.6(Water Absorption IS 3495 (Part 2))	-	750	20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 13801 (2013)

Chequered Cement Concrete Tiles -

7350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	600	20% discount for BIS
Cl 11(Finish)	-	500	20% discount for BIS
Cl 12.1(Concavity & Convexity )	-	750	20% discount for BIS
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	750	20% discount for BIS
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	750	20% discount for BIS
Cl 12.4(Water absorption)	-	1000	20% discount for BIS
Cl 12.5(Wet transverse strength)	-	1000	20% discount for BIS
Cl 12.6(Resistance to wear)	-	2000	20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

7350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	600	20% discount for BIS
Cl 11(Suface Finish)	-	500	20% discount for BIS
Cl 12.2(Concavity & Convexity )	-	750	20% discount for BIS
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	750	20% discount for BIS
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	750	20% discount for BIS
Cl 12.5(Water absorption)	-	1000	20% discount for BIS
Cl 12.6(Wet transverse strength )	-	1000	20% discount for BIS
Cl 12.7(Resistance to wear)	-	2000	20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 15558 (2005)

Mini domestic water heater for use with LPG - Specification

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1(Construction)	-	100		20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

21450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 of IS 5116(General)	-	100	Complete testing charges-21450 20% discount for BIS
4.1.1(General)	-	0	-
4.2 of IS 5116(General)	-	0	-
5 (5.1 of IS 5116)(Materials)	-	0	-
5.1 of IS 5116(Materials)	-	0	-
5 (5.1.1 of IS 5116)(Materials)	-	0	-
5 (5.2 of IS 5116)(Materials)	-	0	-
5 (5.3 of IS 5116)(Materials)	-	0	-
5 (5.4 of IS 5116)(Materials)	-	0	-
5 (5.5 of IS 5116)(Materials)	-	0	-
6 (5.1 of IS 5116)(Materials)	-	0	-
6 (5.5 of IS 5116)(Materials)	-	0	-
6.1(Mechanical (Design for Maintenance))	-	0	-
6.2(Mechanical (Design for Maintenance))	-	0	-
6.3(Mechanical (Design for Maintenance))	-	0	-
6.4(Mechanical (Design for Maintenance))	-	0	-
6.5(Mechanical (Design for Maintenance))	-	0	-
6.6(Mechanical (Design for Maintenance))	-	0	-
7(Rigidity and Stability)	-	0	-
8.1 (7.1 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.2 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.3 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.3.1 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.3.2 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.3.3 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.4.1 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.4.2 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.5 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.6 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.1 (7.7 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
8.2(Mechanical (Workmanship and Finish))	-	0	-
8.3(Mechanical (Workmanship and Finish))	-	0	-
9 (8.1 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.2 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.3 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.4 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.5 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.5.1 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.6 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.7 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.8 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.9 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.10 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.11 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.11.1 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
9 (8.12 of IS 5116)(Mechanical (Workmanship and Finish))	-	0	-
10 (9.1 of IS 5116)(Mechanical (Injector Jets))	-	0	-
10 (9.1.1 of IS 5116)(Mechanical (Injector Jets))	-	0	-
10 (9.2 of IS 5116)(Mechanical (Injector Jets))	-	0	-
11.1 (10.1 of IS 5116)(Mechanical (Burners))	-	0	-
11.1 (10.2 of IS 5116)(Mechanical (Burners))	-	0	-
11.1 (10.3 of IS 5116)(Mechanical (Burners))	-	0	-
11.1 (10.4 of IS 5116)(Mechanical (Burners))	-	0	-
11.1 (10.5 of IS 5116)(Mechanical (Burners))	-	0	-
11.2(Mechanical (Burners))	-	0	-
11.3(Mechanical (Burners))	-	0	-
12.1(Mechanical (Pan Support))	-	0	-
12.1.1(Mechanical (Pan Support))	-	0	-
13.1 (16 of IS 5116)(Mechanical (Gas Soundness))	-	0	-
13.2.1(Mechanical (Gas Soundness))	-	0	-
14.1 (18.1 of IS 5116)(Mechanical (Gas Inlet Connection))	-	0	-
14.1 (18.2 of IS 5116)(Mechanical (Gas Inlet Connection))	-	0	-
14.1 (18.3 of IS 5116)(Mechanical (Gas Inlet Connection))	-	0	-
14.1 (18.4 of IS 5116)(Mechanical (Gas Inlet Connection))	-	0	-
14.2(Mechanical (Gas Inlet Connection))	-	0	-
15 (Annex - C)(Strength and Rigidity)	-	0	-
15.1(Strength and Rigidity)	-	0	-
15.2(Strength and Rigidity)	-	0	-
17.1(Gas Consumption)	-	0	-
17.1(Gas Consumption)	-	0	-
17.1.2(Gas Consumption)	-	0	-
17.2(Gas Consumption)	-	0	-
17.2(Gas Consumption)	-	0	-
17.2.2(Gas Consumption)	-	0	-
18.1(Ignition and Flame travel)	-	0	-
18.2(Ignition and Flame travel)	-	0	-
18.3(Ignition and Flame travel)	-	0	-
18.4 (14.1 of IS 5116)(Ignition and Flame travel)	-	0	-
18.4 (14.2 of IS 5116)(Ignition and Flame travel)	-	0	-
19.1(Flame Stability)	-	0	-
19.1.1(Flame Stability)	-	0	-
19.2(Flame Stability)	-	0	-
19.3(Flame Stability)	-	0	-
20(Noise Control)	-	0	-
21(Flash Back)	-	0	-
22(Formation of Soot)	-	0	-
23(Resistance to Draught)	-	0	-
24 (Annex - E)(Combustion (CO and CO2 ratio))	-	0	-
25.1 ( 23.1 of IS 5116 )(Fire Hazard and Limiting Temperatures)	-	0	-
25.1 ( 23.2 of IS 5116 )(Fire Hazard and Limiting Temperatures)	-	0	-
25.1 ( 23.2.1 of IS 5116 )(Fire Hazard and Limiting Temperatures)	-	0	-
25.1 ( 23.2.2 of IS 5116 )(Fire Hazard and Limiting Temperatures)	-	0	-
25.2(Fire Hazard and Limiting Temperatures)	-	0	-
26(Thermal Efficiency)	-	0	-
26 (for burner 1)(Thermal Efficiency)	-	0	-
26 (for burner 2)(Thermal Efficiency)	-	0	-
26 (for burner 3)(Thermal Efficiency)	-	0	-
26 (for burner 4)(Thermal Efficiency)	-	0	-
26 (for burner 5)(Thermal Efficiency)	-	0	-

Complete

12 Sep, 2022

-
-

IS 15658 (2006)

Precast concrete blocks for paving - Specification

19700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.2(Physical requirement)	-	100	20% discount for BIS
6.1.3(Physical requirement)	-	100	20% discount for BIS
6.1.4(Physical requirement)	-	100	20% discount for BIS
6.2.1 & 7.1(VISUAL INSPECTION)	-	100	20% discount for BIS
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	400	20% discount for BIS
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	100	20% discount for BIS
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	400	20% discount for BIS
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	100	20% discount for BIS
B-1.3.1(MEAN INDIVIDUAL LENGTH (of all eight test specimens), L)	-	400	20% discount for BIS
B-5(AVERAGE LENGTH (Average for eight test specimens), L)	-	100	20% discount for BIS
Table 1(MINIMUM PAVER BLOCK THICKNESS)	-	200	20% discount for BIS
B-1.3.2(MEAN INDIVIDUAL THICKNESS (of all eight test specimens), T)	-	200	20% discount for BIS
B-5(AVERAGE THICKNESS (Average for eight test specimens), T)	-	100	20% discount for BIS
B-1.3.3(INDIVIDUAL ASPECT RATIO (L/T) (of all eight test specimens))	-	400	20% discount for BIS
B-5(AVERAGE ASPECT RATIO (L/T) (for eight test specimens))	-	100	20% discount for BIS
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	500	20% discount for BIS
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	100	20% discount for BIS
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	500	20% discount for BIS
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	100	20% discount for BIS
B-5(INDIVIDUAL PLAN AREA, ASP (of all eight test specimens) )	-	600	20% discount for BIS
B-5(AVERAGE PLAN AREA, ASP (for eight test specimens))	-	100	20% discount for BIS
B-5(INDIVIDUAL WEARING FACE AREA, Asw (of all eight test specimens))	-	600	20% discount for BIS
B-5(AVERAGE WEARING FACE AREA, Asw (for eight test specimens))	-	100	20% discount for BIS
B- 4.3(MEAN INDIVIDUAL SQUARENESS (of all eight test specimens) )	-	600	20% discount for BIS
B-5(AVERAGE SQUARENESS (for eight test specimens))	-	100	20% discount for BIS
6.2.3(THICKNESS OF WEARING LAYER, if the sample is Double Layered (for eight test specimens))	-	0	-
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	1400	20% discount for BIS
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	100	20% discount for BIS
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens) )	-	100	20% discount for BIS
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens))	-	100	20% discount for BIS
6.2.5.1(INDIVIDUAL COMPRESSIVE STRENGTH (Individual strength of eight test specimen))	-	3000	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	1800	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	200	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	1800	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	200	20% discount for BIS
6.2.7(INDIVIDUAL TENSILE SPLITTING STRENGTH (Individual strength of eight test specimen ))	-	2000	20% discount for BIS
6.2.7(AVERAGE TENSILE SPLITTING STRENGTH (for eight test specimen ))	-	200	20% discount for BIS
Annex G-7(INDIVIDUAL FAILURE LOAD/UNIT LENGTH (Individual Failure Load of eight test specimen ))	-	200	20% discount for BIS
6.2.8(INDIVIDUAL FLEXURAL STRENGTH (Individual strength of eight test specimen ))	-	2000	20% discount for BIS
6.2.8(AVERAGE FLEXURAL STRENGTH (Average strength of eight test specimen ))	-	100	20% discount for BIS
Annex-G-7(INDIVIDUAL BREAKING LOAD (Individual Load of eight test specimen ))	-	200	20% discount for BIS
Annex-G-7(AVERAGE BREAKING LOAD)	-	100	20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

10100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.3 (Table 1)(b) 6 mm and above)	-	400		20% discount for BIS

Complete

12 Sep, 2022

-
-

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

Water for Costruction Purpose

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	500	-
Cl 5.4 (b)(Alkalinity)	-	500	-
Cl 5.4 (a)(Acidity)	-	500	-
Cl 5.4 Table 1 (i)(Organic Solids)	-	500	-
Cl 5.4 Table 1 (ii)(Inorganic Solids)	-	500	-
Cl 5.4 Table 1 (iii)(Sulphate)	-	500	-
Cl 5.4 Table 1 (iv)(Chloride)	-	500	-
Cl 5.4 Table 1 (v)(Suspended Matter)	-	500	-
Cl 5.4 .2(pH)	-	500	-

Complete

12 Sep, 2022

-
-

IS 5509 (2000)

Fire retardant plywood - Specification (Second Revision)

BWR

10100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Type based on Flame retardant chemical used)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
8(a) Length)	-	50	-
8(b) Width)	-	50	-
8(c) Thickness 1) less than 6mm ±10% 2) 6 mm and above ±5% )	-	100	-
8.3 & Annex A (d) Edge Straightness 0.2% Max.)	-	100	-
8.3 & Annex A (e) Edge Squareness 0.2% Max.)	-	100	-
9(Workmanship and finish)	-	0	-
12.2(Moisture content )	-	400	-
12.3.1(Flammability )	-	2000	-
12.3.2(Flame Penetration )	-	2000	-
12.2.3(Rate of burning )	-	2000	-
12.4(Glue adhesion (water resistance ))	-	1800	-
12.4(Static Bending Strength as per BWR grade of IS 303 :)	-	1500	-
12.4(Modulus of Rupture, (Along the grain direction of the face veneer))	-	0	-
12.4(Modulus of Rupture, (Along the grain direction of the face veneer))	-	0	-
12.4(Modulus of Rupture, (Across the grain direction of the face veneer))	-	0	-
12.4(Modulus of Rupture, (Across the grain direction of the face veneer))	-	0	-
12.4(Modulus of Elasticity, (Along the grain direction of the face veneer))	-	0	-
12.4(Modulus of Elasticity, (Along the grain direction of the face veneer))	-	0	-
12.4(Modulus of Elasticity, (Across the grain direction of the face veneer))	-	0	-
12.4(Modulus of Elasticity, (Across the grain direction of the face veneer))	-	0	-

Complete

12 Sep, 2022

-
-

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

BWP/CS,CSC,CSFF

13100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Types)	-	0	20 % discount to BIS
7.2(DIMENSIONS & TOLERANCES )	-	50	20 % discount to BIS
7.2(DIMENSIONS & TOLERANCES )	-	50	20 % discount to BIS
7.3(DIMENSIONS & TOLERANCES )	-	80	20 % discount to BIS
7.4(DIMENSIONS & TOLERANCES )	-	80	20 % discount to BIS
7.4(DIMENSIONS & TOLERANCES )	-	80	20 % discount to BIS
8.1(WORKMANSHIP AND FINISH )	-	30	20 % discount to BIS
8.3(WORKMANSHIP AND FINISH )	-	30	20 % discount to BIS
10.1.1(MOISTURE CONTENT)	-	400	20 % discount to BIS
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	600	20 % discount to BIS
10.1.2, 10.1.2.2(GLUE ADHESION IN DRY STATE)	-	400	20 % discount to BIS
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	1500	20 % discount to BIS
10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST)	-	900	20 % discount to BIS
10.1.4(RESISTANCE TO WATER TEST)	-	600	20 % discount to BIS
10.1.5(MYCOLOGICAL TEST )	-	1800	20 % discount to BIS
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	600	20 % discount to BIS
10.1.5.2(MYCOLOGICAL TEST )	-	400	20 % discount to BIS
10.1.6(TENSILE STRENGTH)	-	1000	20 % discount to BIS
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	750	20 % discount to BIS
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	750	20 % discount to BIS
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1000	20 % discount to BIS
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1000	20 % discount to BIS
10.1.9(RETENTION OF PRESERVATIVE)	-	1000	20 % discount to BIS
12, 12.1(MARKING)	-	0	20 % discount to BIS
12, 12.2(MARKING)	-	0	20 % discount to BIS

Complete

12 Sep, 2022

-
-

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

Coarse & Fine

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1000	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.4.2(a)( Aggregates Impact Value)	-	500	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.4.3(a)( Aggregate Abrasion Value)	-	500	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate)	-	800	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Grading Zone)	-	800	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Nominal Size )	-	800	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	0	-
5.4.2(b)( Aggregates Impact Value)	-	0	-
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	0	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	0	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	0	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	0	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	0	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	0	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	0	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	0	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	0	-
6.2-Table 7(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Nominal Size of aggregate)	-	800	-
6.2-Table 7(i)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 80 mm sieve)	-	0	-
6.2-Table 7(ii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 63 mm sieve)	-	0	-
6.2-Table 7(iii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 40 mm sieve)	-	0	-
6.2-Table 7(iv)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 20 mm sieve)	-	0	-
6.2-Table 7(v)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 16 mm sieve)	-	0	-
6.2-Table 7(vi)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 12.5 mm sieve)	-	0	-
6.2-Table 7(vii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 10 mm sieve)	-	0	-
6.2-Table 7(viii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 4.75 mm sieve)	-	0	-
6.2-Table 7(ix)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 2.36 mm sieve)	-	0	-
6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve )	-	0	-
6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve )	-	0	-
6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve )	-	0	-
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	0	-
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	0	-
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	0	-
6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve )	-	0	-
6.4-Table 10(i)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 80mm Sieve )	-	0	-
6.4-Table 10(ii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 40mm Sieve )	-	0	-
6.4-Table 10(iii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 20mm Sieve )	-	0	-
6.4-Table 10(iv)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 4.75mm Sieve )	-	0	-
6.4-Table 10(v)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 600µm Sieve )	-	0	-
6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve )	-	0	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(fine aggregate))	-	600	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (fine aggregate))	-	750	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	750	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(II) IS:4032(Total sulphate content (fine aggregate))	-	750	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	1800	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.5-IS: 2386 (P-5)(Soundness (fine aggregate))	-	1500	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (Note-3) IS-2386 (P-2)(Mica content (fine aggregate))	-	0	-
5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Effect of organic impurities on strength of mortar (fine aggregate))	-	0	-
5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Effect of organic impurities on strength of mortar (fine aggregate))	-	0	-
5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Organic impurities (fine aggregate))	-	0	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (fine aggregate))	-	1800	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (fine aggregate))	-	0	-
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (fine aggregate ))	-	0	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (fine aggregate ))	-	0	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(coarse aggregate))	-	600	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (coarse aggregate))	-	750	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(III) BN EN: 1744(Water soluble chloride content (coarse aggregate))	-	750	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(II) BN EN: 1744(Total sulphate content (coarse aggregate))	-	750	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.5-IS: 2386 (P-5)(Soundness (coarse aggregate))	-	1500	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.3-IS: 2386 (P-1)(Combined elongation & flakiness index (coarse aggregate))	-	1000	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (coarse aggregate))	-	1800	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (iv) IS-2386 (P-2)(Soft fragments (coarse aggregate))	-	0	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (coarse aggregate))	-	0	-
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (coarse aggregate ))	-	0	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (coarse aggregate ))	-	0	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate))	-	1800	Testing Charges-12750(Coarse Aggregate), 9750 (Fine Aggregate) 20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

19700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.2(Physical requirement)	-	100	20% discount to BIS
6.1.3(Physical requirement)	-	100	20% discount to BIS
6.1.4(Physical requirement)	-	100	20% discount to BIS
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	400	20% discount to BIS
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	100	20% discount to BIS
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	400	20% discount to BIS
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	100	20% discount to BIS
B-1.3.1(MEAN INDIVIDUAL LENGTH (of all eight test specimens), L)	-	400	20% discount to BIS
B-5(AVERAGE LENGTH (Average for eight test specimens), L)	-	100	20% discount to BIS
Table 1(MINIMUM PAVER BLOCK THICKNESS)	-	200	20% discount to BIS
B-1.3.2(MEAN INDIVIDUAL THICKNESS (of all eight test specimens), T)	-	200	20% discount to BIS
B-5(AVERAGE THICKNESS (Average for eight test specimens), T)	-	100	20% discount to BIS
B-1.3.3(INDIVIDUAL ASPECT RATIO (L/T) (of all eight test specimens))	-	400	20% discount to BIS
B-5(AVERAGE ASPECT RATIO (L/T) (for eight test specimens))	-	100	20% discount to BIS
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	500	20% discount to BIS
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	500	20% discount to BIS
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	100	20% discount to BIS
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	100	20% discount to BIS
B-5(INDIVIDUAL PLAN AREA, ASP (of all eight test specimens) )	-	600	20% discount to BIS
B-5(AVERAGE PLAN AREA, ASP (for eight test specimens))	-	100	20% discount to BIS
B-5(INDIVIDUAL WEARING FACE AREA, Asw (of all eight test specimens))	-	600	20% discount to BIS
B-5(AVERAGE WEARING FACE AREA, Asw (for eight test specimens))	-	100	20% discount to BIS
B- 4.3(MEAN INDIVIDUAL SQUARENESS (of all eight test specimens) )	-	600	20% discount to BIS
B-5(AVERAGE SQUARENESS (for eight test specimens))	-	100	20% discount to BIS
6.2.3(THICKNESS OF WEARING LAYER, if the sample is Double Layered (for eight test specimens))	-	0	-
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	1400	20% discount to BIS
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	100	20% discount to BIS
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens) )	-	100	20% discount to BIS
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens))	-	100	20% discount to BIS
6.2.5.1(INDIVIDUAL COMPRESSIVE STRENGTH (Individual strength of eight test specimen))	-	3000	20% discount to BIS
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	1800	20% discount to BIS
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	200	20% discount to BIS
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	1800	20% discount to BIS
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	200	20% discount to BIS
6.2.7(INDIVIDUAL TENSILE SPLITTING STRENGTH (Individual strength of eight test specimen ))	-	2000	20% discount to BIS
6.2.7(AVERAGE TENSILE SPLITTING STRENGTH (for eight test specimen ))	-	200	20% discount to BIS
Annex G-7(INDIVIDUAL FAILURE LOAD/UNIT LENGTH (Individual Failure Load of eight test specimen ))	-	200	20% discount to BIS
6.2.8(INDIVIDUAL FLEXURAL STRENGTH (Individual strength of eight test specimen ))	-	2000	20% discount to BIS
6.2.8(AVERAGE FLEXURAL STRENGTH (Average strength of eight test specimen ))	-	100	20% discount to BIS
Annex-G-7(INDIVIDUAL BREAKING LOAD (Individual Load of eight test specimen ))	-	200	20% discount to BIS
Annex-G-7(AVERAGE BREAKING LOAD)	-	100	20% discount to BIS
6.2.1 & 7.1(VISUAL INSPECTION)	-	100	20% discount to BIS
Clause 7.1.1 (General Quality)	-	100	20% discount to BIS
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	100	20% discount to BIS
Clause 7.1.3 (Colour and Texture)	-	0	-
Clause 6.3 (Bonding and Delamination between the layers of paver blocks)	-	100	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	200	20% discount to BIS
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	800	20% discount to BIS
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	100	20% discount to BIS
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	400	20% discount to BIS
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	100	20% discount to BIS
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	400	20% discount to BIS
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	100	20% discount to BIS
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	400	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	100	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	400	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	100	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	400	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	100	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	600	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	100	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	600	20% discount to BIS
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	700	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	1400	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	100	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)( Indivdual Compressive strength)	-	3000	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	200	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	1800	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	200	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	18000	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	200	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength )	-	2000	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	200	20% discount to BIS
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	100	20% discount to BIS
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	100	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength )	-	2000	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	100	20% discount to BIS
Clause 7.3, Annex G(Individual Breaking Load)	-	200	20% discount to BIS
Clause 7.3, Annex G(Average Breaking Load)	-	100	20% discount to BIS
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 10 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 10 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 25 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 25 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 50 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 50 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	0	-

Complete

12 Sep, 2022

-
-

IS 15380 (2003)

Moulded Raised High Density Fibre (HDF) Panel Doors -

Heavy & Light Duty

15300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, Table-1(dimension )	-	0	20 % discount to BIS
7.1(Heavy duty (Construction))	-	0	20 % discount to BIS
7.2(Light duty)	-	0	20 % discount to BIS
7.3(Empanelment)	-	25	20 % discount to BIS
7.4(Lipping )	-	25	20 % discount to BIS
7.5(rebating )	-	25	20 % discount to BIS
11.1(Dimension and squareness test)	-	300	20 % discount to BIS
11.2(General flatness test)	-	400	20 % discount to BIS
11.3(low Planeness Teat)	-	750	20 % discount to BIS
11.4(Impact Indentation Test)	-	750	20 % discount to BIS
11.5(Flexure Test)	-	750	20 % discount to BIS
11.6(edge loading test)	-	750	20 % discount to BIS
11.7(shock resistance test)	-	750	20 % discount to BIS
11.8(Buckling Test)	-	750	20 % discount to BIS
11.9(slamming Test)	-	750	20 % discount to BIS
11.1(misuse test)	-	750	20 % discount to BIS
11.11(varying humidity test)	-	2100	20 % discount to BIS
11.12(end immersion test)	-	1600	20 % discount to BIS
11.13(glue adhesion test)	-	800	20 % discount to BIS
11.14(screw withdrawal resistance test)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
Clause 6.2(Moisture content)	-	800	20 % discount to BIS
Clause 6.2(Formaldehyde emission)	-	2000	20 % discount to BIS
9(workmanship and finish)	-	25	20 % discount to BIS

Complete

12 Sep, 2022

-
-

IS 3564 (1995)

Hydraulically Regulated Door Closers -Specification

Type A & B

1700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Marking)	-	500	Complete testing charges for clause 6,8,9,11,12,13-500 20 % discount to BIS GSTIN extra as per Government Rule
12(Packing)	-	500	Complete testing charges for clause 6,8,9,11,12,13-500 20 % discount to BIS GSTIN extra as per Government Rule
13(Accessories)	-	500	Complete testing charges for clause 6,8,9,11,12,13-500 20 % discount to BIS GSTIN extra as per Government Rule
6(Nominal Sizes)	-	500	Complete testing charges for clause 6,8,9,11,12,13-500 20 % discount to BIS GSTIN extra as per Government Rule
8(Essential Requirements)	-	2000	20 % discount to BIS GSTIN extra as per Government Rule
9(Finish)	-	500	Complete testing charges for clause 6,8,9,11,12,13-500 20 % discount to BIS GSTIN extra as per Government Rule
10Annex B(Test)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
B-1.4(c) Performance Requirements)	-	2000	20 % discount to BIS GSTIN extra as per Government Rule
B-1.5(d) Endurance Test)	-	12000	20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 14587 (1998)

Prelaminated Medium Density Fibre Board -specification

Exterior & Interior/Grade I/Grade II/Type I-IV

31200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions and tolerances)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.2, Table-1(Test for Density)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.4, Table-1(Test for Water Absorption)	-	1200	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.5(test for swelling in water)	-	1200	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.6(test for modulis of rupture)	-	1000	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.7(Test for tensile strength perpendicular to Surface)	-	1000	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.8(Test for tensile strength perpendicular to Surface after ageing )	-	3000	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.9(test screw withdrawal strength)	-	2000	Combined for Face & Edge Screw Withdrawal-Rs. 2000 Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.1(test for surface abrasion resistance)	-	1500	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.11(test for resistance to steam)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.12(test for resistance to crack)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.13(test for resistance to cigarette burn)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
10.14(test for resistance to stain)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 12823 (2015)

Prelaminated Particle Boards from Wood and other Lignocellulosic Material - Specification ( First Revision )

Exterior & Interior/Grade I/Grade II/Type I-IV

31200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Grades & Types)	-	600	Complete testing Charges for Clause 4,6,7,8-Rs.600 Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 6(Manufacture)	-	600	Complete testing Charges for Clause 4,6,7,8-Rs.600 Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 7(Finish)	-	600	Complete testing Charges for Clause 4,6,7,8-Rs.600 Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 8(Dimensions & Tolerances)	-	600	Complete testing Charges for Clause 4,6,7,8-Rs.600 Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.2(Test For Density)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.3(Test For Moisture Content)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.4(For Water AbsorptionTest )	-	1200	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.5(For Swelling in water Test )	-	1200	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.6(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	1000	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.7(For Determination of Tensile Strength Perpendicular to Surface)	-	1000	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.8(For Determination of Tensile Strength Perpendicular to Surface After Ageing Test)	-	3000	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.9(Test For Screw Withdrawal Strength)	-	2000	Combined Charges for Screw Withdrawal for Face & Edge-Rs. 2000 Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.10 & Annex C( Test For Abrasion Resistance)	-	1500	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.11 & Annex D( Test For Resistance to Steam)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.12 & Annex E( Test For Crack Resistance)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.13 & Annex F( Test For Resistance to Cigarette Burn)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.14 & Annex G( Test For Resistance to Stain)	-	600	Complete testing charges for Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100 20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 12406 (2003)

Medium density fibre boards for general purpose - Specification (First Revision)

Exterior & Interior/SBG I/SBG II

26400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4( Types)	-	600	Combined charges for Clause 4, 7 & 8-RS. 600 Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 7(Finish)	-	600	Combined charges for Clause 4, 7 & 8-RS. 600 Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 8(Dimensions & Tolerances)	-	600	Combined charges for Clause 4, 7 & 8-RS. 600 Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.4(Test For Density)	-	600	Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.5(Test For Moisture Content)	-	600	Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.6(Test For water Absorption)	-	1200	Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.7.1(Due To General Absorption)	-	1200	Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.7.2(Due To Surfacel Absorption)	-	1500	Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.8(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	1000	Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.9(Test For Internal Bond)	-	4000	Combined charges for Dry & Accelerated internal Bond-RS. 4000 Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
Cl 11.10(Test For Screw Withdrawal Strength)	-	2000	Combined charges for Face & Edge-2000 Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 3087 (2005)

Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

Interior & Exterior/FPS/FPT-1/FPT-2/XPS/XPT

14700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1 (i) Table 1(Density Variation (Flat Pressed Single Layer))	-	600	Complete testing charges- Exterior Grade-Rs.14700, Interior grade-11700 20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Single Layer))	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) Table 1 (b)(Water absorption, 24h soacking (Flat Pressed Single Layer))	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Single Layer))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Single Layer))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Single Layer))	-	1500	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Single Layer))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Single Layer))	-	1000	C20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 1))	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 2))	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Extrusion Pressed Solids) XPS)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Extrusion Pressed Tubular) XPS)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 1))	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 2))	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Solids) XPS)	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Tubular) XPS)	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 1))	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 2))	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Solids) XPS)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Tubular) XPS)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 1))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 2))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Solids) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Tubular) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Single Layer))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 1))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 2))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Solids) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Tubular) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 1))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 2))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Solids) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Tubular) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 1))	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 2))	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Solids) XPS)	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Tubular) XPS)	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Tubular) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Extrusion Pressed Tubular) XPT)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Tubular) XPT)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Extrusion Pressed Tubular) XPT)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface,Upto 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface,Above 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 848 (2006)

Synthetic resin adhesives for plywood (Phenolic And Aminoplastic) - Specification (Second Revision)

MR-BWR-BWP

23200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 Table (i)(BWP (BOiling WaterProof))	-	6800	BWP-8000 (with cyclic test) & 2000 without cyclic test BWR-8000 (with cyclic test) & 2000 without cyclic test MR-7200 (with cyclic test) & 2000 without cyclic test 20 % discount to BIS GSTIN extra as per Government Rule
4 Table (i)(BWR (Boiling Water Resistant))	-	6800	BWP-8000 (with cyclic test) & 2000 without cyclic test BWR-8000 (with cyclic test) & 2000 without cyclic test MR-7200 (with cyclic test) & 2000 without cyclic test 20 % discount to BIS GSTIN extra as per Government Rule
4 Table (i)(MR (Moisture Ressistant))	-	6000	BWP-8000 (with cyclic test) & 2000 without cyclic test BWR-8000 (with cyclic test) & 2000 without cyclic test MR-7200 (with cyclic test) & 2000 without cyclic test 20 % discount to BIS GSTIN extra as per Government Rule
5,7.4(Keeping Quality (Resistance to heat Polymerization))	-	0	-
7.4(Acidity and Alkalinity ( pH))	-	1200	BWP-8000 (with cyclic test) & 2000 without cyclic test BWR-8000 (with cyclic test) & 2000 without cyclic test MR-7200 (with cyclic test) & 2000 without cyclic test 20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 1328 (1996)

Veneered Decorative Plywood -Specification

MR-BWR

4700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
4.1(Grade - For MR)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
4.2(Type - For Type 1)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
4.2(Type - For Type 2)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Length - Cl. 8)	-	400	Complete Testing Charges for Clause 8-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Width - Cl. 8)	-	400	Complete Testing Charges for Clause 8-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	400	Complete Testing Charges for Clause 8-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	400	Complete Testing Charges for Clause 8-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Squareness - Annexure C)	-	400	Complete Testing Charges for Clause 8-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
9(Finish - Cl. 9.1, 8.3)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3,9-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
9(Finish - Cl. 9.2, 8.3)	-	400	Complete Testing Charges for Clause 4.1,4.2,7.1.1,7.1.2,7.1.3,7.2.1,7.2.2,7.2.3,9-Rs. 400 20 % discount to BIS GSTIN extra as per Government Rule
11(Tests - Moisture Content - Part 1 of IS 1734)	-	400	20 % discount to BIS GSTIN extra as per Government Rule
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	1800	20 % discount to BIS GSTIN extra as per Government Rule
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	1800	20 % discount to BIS GSTIN extra as per Government Rule

Complete

12 Sep, 2022

-
-

IS 2202 : Part 1 (1999)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

BWP

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(Workmanship & finish - IS 2202(Pt-1))	-	20	20 % discount to BIS
9.2(Workmanship & finish - IS 2202(Pt-1))	-	20	20 % discount to BIS
9.3(Workmanship & finish - IS 2202(Pt-1))	-	20	20 % discount to BIS
11.1(Height - IS 4020 (Pt-2))	-	50	20 % discount to BIS
11.1(Width- IS 4020 (Pt-2))	-	20	20 % discount to BIS
11.1(Thickness - IS 4020 (Pt-2))	-	100	20 % discount to BIS
11.1( Squareness Test - IS 4020 (Pt-2))	-	100	20 % discount to BIS
11.1(Variation in thickness - IS 4020 (Pt-2))	-	40	20 % discount to BIS
11.3(Depth of deviation - IS 4020(Pt-4))	-	750	20 % discount to BIS
11.2( Twist, cupping & wrapping - IS 4020 (Pt-3))	-	400	20 % discount to BIS
11.4(Impact Indentation Test - IS 4020(Pt-5))	-	650	20 % discount to BIS
11.4(Depth of indentation - IS 4020(Pt-5))	-	100	20 % discount to BIS
11.5(Deflection at maximum load - IS 4020(Pt-6))	-	650	20 % discount to BIS
11.5(Residual deflection - IS 4020(Pt-6))	-	100	20 % discount to BIS
11.6(Deflection of the edge at maximum load - IS 4020(Pt-7))	-	500	20 % discount to BIS
11.6(Residual deflection after removal of load - IS 4020(Pt-7))	-	100	20 % discount to BIS
11.6(Lateral buckling during loading - IS 4020(Pt-7))	-	100	20 % discount to BIS
11.6(Residual lateral buckling - IS 4020(Pt-7))	-	50	20 % discount to BIS
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	500	20 % discount to BIS
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	250	20 % discount to BIS
11.8(Buckling Test - IS 4020(Pt-9))	-	500	20 % discount to BIS
11.8(Initial deflection - IS 4020(Pt-9))	-	150	20 % discount to BIS
11.8(Residual deformation after 15 minutes of unloading - IS 4020(Pt-9))	-	100	20 % discount to BIS
11.9(Slamming Test - IS 4020(Pt-10))	-	750	20 % discount to BIS
11.1(Misuse Test - IS 4020(Pt-11))	-	750	20 % discount to BIS
11.11(Varying Humidity Test - IS 4020(Pt-12))	-	1500	20 % discount to BIS
11.11(Maximum departure from the general planeness - IS 4020(Pt-12))	-	300	20 % discount to BIS
11.11(The recovery of the original size after subjecting the door to high and low humidity- IS 4020(Pt-12))	-	300	20 % discount to BIS
11.12(End Immersion Test - IS 4020(Pt-13))	-	1600	20 % discount to BIS
11.13(Knife Test - IS 4020(Pt-14))	-	400	20 % discount to BIS
11.14(Glue Adhesion Test - IS 4020(Pt-15))	-	800	20 % discount to BIS
11.15(Screw Withdrawal Resistance test - IS 4020 (Pt-16))	-	400	20 % discount to BIS
11.15(Screw Withdrawal Strength - IS 4020 (Pt-16))	-	400	20 % discount to BIS

Complete

12 Sep, 2022

-
-

IS 710 (2010)

Marine plywood - Specification (Second Revision)

BWP

12600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(DIMENSIONS)	-	50	20 % discount to BIS
6.1(DIMENSIONS)	-	50	20 % discount to BIS
6.2(DIMENSIONS)	-	80	20 % discount to BIS
6.3(DIMENSIONS)	-	80	20 % discount to BIS
6.3(DIMENSIONS)	-	80	20 % discount to BIS
7.1(WORKMANSHIP AND FINISH )	-	15	20 % discount to BIS
7.2(WORKMANSHIP AND FINISH )	-	15	20 % discount to BIS
7.3(WORKMANSHIP AND FINISH )	-	15	20 % discount to BIS
7.5(WORKMANSHIP AND FINISH )	-	15	20 % discount to BIS
9.1.1(MOISTURE CONTENT)	-	400	20 % discount to BIS
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	600	20 % discount to BIS
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	400	20 % discount to BIS
9.1.3 , 9.1.3.1.1(Water resistance test)	-	2100	20 % discount to BIS
9.1.5(Mycological test)	-	1800	20 % discount to BIS
9.1.5 , 9.1.3.1.1(Mycological test)	-	600	20 % discount to BIS
9.1.5 , 9.1.3.1.2(Mycological test)	-	400	20 % discount to BIS
9.1.4(Tensile strength)	-	1000	20 % discount to BIS
9.1.6 (Table 3)(Static bending strength)	-	750	20 % discount to BIS
9.1.6 (Table 3)(Static bending strength)	-	750	20 % discount to BIS
9.1.7 (Table 4)(Wet bending strength)	-	1000	20 % discount to BIS
9.1.7 (Table 4)(Wet bending strength)	-	1000	20 % discount to BIS
9.1.8(Retention of preservative)	-	1000	20 % discount to BIS
11.1(MARKING)	-	0	NA
11.2(MARKING)	-	0	NA
9.1.3 , 9.1.3.1.2(Water resistance test)	-	400	20 % discount to BIS

Complete

12 Sep, 2022

-
-

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

MR-BWP

9850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	400	20 % discount to BIS
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	400	20 % discount to BIS
7.3(Dimensional Requirements - Length - 8.1.4)	-	50	20 % discount to BIS
7.3(Dimensional Requirements - Width - 8.1.4)	-	50	20 % discount to BIS
7.3(Dimensional Requirements - Thickness - Annexure E)	-	80	20 % discount to BIS
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	100	20 % discount to BIS
7.3(Dimensional Requirements - Squareness - Annexure D)	-	100	20 % discount to BIS
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	20	20 % discount to BIS
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	280	20 % discount to BIS
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	280	20 % discount to BIS
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	280	20 % discount to BIS
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	280	20 % discount to BIS
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	40	20 % discount to BIS
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	40	20 % discount to BIS
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	3300	20 % discount to BIS
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	800	20 % discount to BIS
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	1800	20 % discount to BIS
9.2.3(Adhesion of Plies - Annexure H)	-	400	20 % discount to BIS
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	100	20 % discount to BIS
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	275	20 % discount to BIS
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	100	20 % discount to BIS
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	275	20 % discount to BIS
9.2.6(Spot test - Annexure L)	-	400	20 % discount to BIS

Complete

12 Sep, 2022

-
-

IS 303 (1989)

Plywood for General Purposes -

MR-BWR

7800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Grade - For BWR grade)	-	0	20% discount to BIS
4(Grade - For MR grade)	-	0	20% discount to BIS
5.1(Type - For AA Type)	-	0	20% discount to BIS
5.1(Type - For AB Type)	-	0	20% discount to BIS
5.1(Type - For BB Type)	-	0	20% discount to BIS
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	400	20% discount to BIS
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	30	20% discount to BIS
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	30	20% discount to BIS
8(Dimensions & Tolerances - Length - Cl. 8)	-	50	20% discount to BIS
8(Dimensions & Tolerances - Width - Cl. 8)	-	50	20% discount to BIS
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	80	20% discount to BIS
8(Dimensions & Tolerances - Squareness - Annexure C)	-	80	20% discount to BIS
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	80	20% discount to BIS
11.3(Moisture Content - Part 1 of IS 1734)	-	400	20% discount to BIS
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	2900	20% discount to BIS
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	1000	20% discount to BIS
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	1900	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	100	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	100	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	100	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	100	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	100	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	100	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	100	20% discount to BIS
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	100	20% discount to BIS

Complete

12 Sep, 2022

-
-

Bureau of Indian Standards

The National Standards Body of India

Hindustaan Test House

Plot No. 36,Sector 1, HSIIDC IGC Saha, Ambala Cantt, Ambala Cantt, Ambala, Haryana, 133104

9355002828 [email protected]

Scope List