BIS - LIMS (Laboratory Information Management System)

JBS TESTING SOLUTIONS JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 [email protected]

Scope List

Reset

40 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

M-30, M35, M40, M50, M55

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.3, Annex G(Average Breaking Load)	-	3000	For complete testing
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	3000	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	3000	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	3000	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	3000	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	3000	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	3000	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	3000	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	3000	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)( Indivdual Compressive strength)	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	3000	-
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	3000	-
Clause 7.3, Annex G(Individual Breaking Load)	-	3000	-
Clause 7.1.1 (General Quality)	-	3000	-
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	3600	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	3000	-

Complete

-
-

IS 1538 (1993)

Cast iron fittings for pressure pipes for water, gas and sewage - Specification (Third Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8(Hydrostatic Test)	-	10500		-

Complete

-
-

IS 15658 (2006)

Precast concrete blocks for paving - Specification

M-30, M-35, M-40, M-50 & M-55 (Size 50 mm to 120 mm)

18600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.2(Physical requirement)	-	3000	For Dimension and Tolerance and other visual parameters
6.1.3(Physical requirement)	-	3000	For Dimension and Tolerance and other visual parameters
6.1.4(Physical requirement)	-	3000	For Dimension and Tolerance and other visual parameters
6.2.1 & 7.1(VISUAL INSPECTION)	-	3000	For Dimension and Tolerance and other visual parameters
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	3000	For Dimension and Tolerance and other visual parameters
B-1.3.1(MEAN INDIVIDUAL LENGTH (of all eight test specimens), L)	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE LENGTH (Average for eight test specimens), L)	-	3000	For Dimension and Tolerance and other visual parameters
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	3600	-
Table 1(MINIMUM PAVER BLOCK THICKNESS)	-	3000	For Dimension and Tolerance and other visual parameters
B-1.3.2(MEAN INDIVIDUAL THICKNESS (of all eight test specimens), T)	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE THICKNESS (Average for eight test specimens), T)	-	3000	For Dimension and Tolerance and other visual parameters
B-1.3.3(INDIVIDUAL ASPECT RATIO (L/T) (of all eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE ASPECT RATIO (L/T) (for eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-5(INDIVIDUAL PLAN AREA, ASP (of all eight test specimens) )	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE PLAN AREA, ASP (for eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-5(INDIVIDUAL WEARING FACE AREA, Asw (of all eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE WEARING FACE AREA, Asw (for eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
6.2.3(THICKNESS OF WEARING LAYER, if the sample is Double Layered (for eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	3600	-
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens) )	-	3000	For Compression Test
6.2.5.1(INDIVIDUAL COMPRESSIVE STRENGTH (Individual strength of eight test specimen))	-	3000	For Compression Test
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	3000	For Abrassion Resistance test
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	3000	For Abrassion Resistance test
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	3000	For Abrassion Resistance test
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	3000	For Abrassion Resistance test
6.2.7(INDIVIDUAL TENSILE SPLITTING STRENGTH (Individual strength of eight test specimen ))	-	3000	For Tensile splitting test
6.2.7(AVERAGE TENSILE SPLITTING STRENGTH (for eight test specimen ))	-	3000	For Tensile splitting test
Annex G-7(INDIVIDUAL FAILURE LOAD/UNIT LENGTH (Individual Failure Load of eight test specimen ))	-	3000	For Tensile splitting test
6.2.8(INDIVIDUAL FLEXURAL STRENGTH (Individual strength of eight test specimen ))	-	3000	For Flexural Test
6.2.8(AVERAGE FLEXURAL STRENGTH (Average strength of eight test specimen ))	-	3000	For Flexural Test
Annex-G-7(INDIVIDUAL BREAKING LOAD (Individual Load of eight test specimen ))	-	3000	For Flexural Test
Annex-G-7(AVERAGE BREAKING LOAD)	-	3000	For Flexural Test
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	3000	For Dimension and Tolerance and other visual parameters
B- 4.3(MEAN INDIVIDUAL SQUARENESS (of all eight test specimens) )	-	3000	For Dimension and Tolerance and other visual parameters
B-5(AVERAGE SQUARENESS (for eight test specimens))	-	3000	For Dimension and Tolerance and other visual parameters

Complete

-
-

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	300	For uniformity/ Mass of Zinc coating
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	300	For uniformity/ Mass of Zinc coating
6.2 AND AS PER IS 513(NITROGEN)	-	1000	For complete chemical analysis
6.2 AND AS PER IS 513(CARBON)	-	999.96	For complete chemical analysis
6.2 AND AS PER IS 513(SILICON)	-	1000	For complete chemical analysis
6.2 AND AS PER IS 513(MANGANESE)	-	1000	For complete chemical analysis
6.2 AND AS PER IS 513(PHOSPHORUS)	-	1000	For complete chemical analysis

Complete

-
-

IS 4351 (2003)

Steel Door Frames -

Profile A, B, C, D & E

2950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, Table 1(Mild steel sheet (cold rolled))	-	50	(5% discount to BIS)
5, Table 1(Galvanized steel sheets — Plain grade — Lock forming (GPL), Zinc coating 120 g/m2 inchssive of both sides)	-	50	(5% discount to BIS)
5, Table 1(Stainless steel Grade — X07Crl 7 (430) X04Cr19N;; (304 S1 ))	-	50	(5% discount to BIS)
6.1(Sizes)	-	1500	(5% discount to BIS) Testing charges for complete Cl 6
6.2(Tolerances)	-	1500	(5% discount to BIS) Testing charges for complete Cl 6
6.3(Designation)	-	50	(5% discount to BIS)
7, Table 2(Profile)	-	850	(5% discount to BIS)
8.0(CONSTRUCTION)	-	50	(5% discount to BIS)
10.1(Fixing Lugs (Holdfasts))	-	50	(5% discount to BIS)
10.2, Table 3(Steel butt hinge— medium weight)	-	50	(5% discount to BIS)
10.3(Mortar Guards)	-	50	(5% discount to BIS)
10.4(Aldrops, Sliding Bolts and Tower Bolts)	-	50	(5% discount to BIS)
10.5(Lock Strike Plate)	-	50	(5% discount to BIS)
10.6(Shock Absorbers)	-	50	(5% discount to BIS)
11.3(Powder Coatings)	-	50	(5% discount to BIS)

Complete

-
-

IS 318 (1981)

Specification for leaded tin bronze ingots and castings (Second Revision)

2400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(SIZE AND SHAPE)	-	900	For dimension, mechanical and manufacturer parameters
6(FREEDOM FROM DEFECTS)	-	900	For dimension, mechanical and manufacturer parameters
4, Table 2.(MECHANICAL PROPERTIES)	-	900	For dimension, mechanical and manufacturer parameters
3, Table 1.(CHEMlCAL COMPOSITION)	-	1500	-

Complete

-
-

IS 13757 (1993)

Burnt Clay Fly Ash Building Bricks-specification

3700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0(GENERAL QUALITY)	-	700		For Dimension and tolerance and other visual parameters

Complete

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

upto 12 mm only

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 15(Length, Width & Thickness)	-	5500	For Dimension and Tolerance and Mechanical properties parameters
Cl 10.3(UTM)	-	5500	For Dimension and Tolerance and Mechanical properties parameters
Cl 11.3(Press)	-	5500	For Dimension and Tolerance and Mechanical properties parameters
Cl 12(Sudden Load Applied)	-	4000	For impact Test

Complete

-
-

IS 1239 : Part 2 (2011)

Steel tubes, tubulars and other steel fittings - Specification: Part 2 steel pipe fittings (Fifth Revision)

4800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces-Approximate Standard Length(A) )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-A )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-B )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-C )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-C)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.3.2(DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.3.2(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-The face of the back nut angle)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.4.1 -Table 4(Bends and springs)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.4.1 -Table 4(Bends and springs-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.4.1 -Table 4(Bends and springs-R)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.4.1 -Table 4(Bends and springs-C)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.4.1 -Table 4(Bends and springs-D)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.4.1 -Table 4(Bends and springs-E)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.5-Table 5( Return Bends)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.5-Table 5( Return Bends-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.5-Table 5( Return Bends-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.6 -Table 6(Sockets)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.6 -Table 6(Sockets-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.6 -Table 6(Sockets-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
8.6 -Table 6(Maximum Inside Diameter of Internal Parallel Thread)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9(DIMENSIONS OF STEEL FITTINGS (OTHER THAN TUBULARS))	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 7(Dimensions of Screwed Ends of Fittings-D )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 7(Dimensions of Screwed Ends of Fittings-E )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 7(Dimensions of Screwed Ends of Fittings-d )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 7(Dimensions of Screwed Ends of Fittings-Taper )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 8 (Dimensions of Elbows, Tees and Crosses, Equal-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 9 (Dimensions of Elbows Reducing-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 9 (Dimensions of Elbows Reducing-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 13( Dimensions of Crosses, Reducing-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 13( Dimensions of Crosses, Reducing-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 14( Elbows, Tees and Crosses, Side Outlet, Equal-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 14( Elbows, Tees and Crosses, Side Outlet, Equal-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Minimum Bore of Male End)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Maximum Bore of Male End)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 16( Dimensions of Elbows, Equal, 135°-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 17 (Dimensions of Y-Pieces, Female, Equal-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 18 (Dimensions of Socket, Reducing-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 19 (Dimensions of Caps-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 19 (Dimensions of Caps-T)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-S)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-H)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-D)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-K)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 21 (Dimensions of Elbows, Tees and Crosses, Male, Equal-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-A )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-B )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 24(Dimensions of Socket Unions-A )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 25 (Dimensions of Pipe Unions-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 26 (Dimensions of Union Bends-A )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 26 (Dimensions of Union Bends-B )	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 27 (Dimensions of Hexagon Bushes-L)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 27 (Dimensions of Hexagon Bushes-T)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 27 (Dimensions of Hexagon Bushes-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 27 (Dimensions of Hexagon Bushes-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-L)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-T)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-A)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-C)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-B)	-	2400	For Complete Cl 8 & 9 (5% discount for BIS)
11.1(a)(Internal hydraulic Pressure Test)	-	1750	For Complete Cl 11 (5% discount for BIS)
11.1(a)(Internal Air Pressure Test)	-	1750	For Complete Cl 11 (5% discount for BIS)
11.2.1( Drift Expanding Test)	-	1750	For Complete Cl 11 (5% discount for BIS)
11.2.2 (Taper Screw Plug Test)	-	1750	For Complete Cl 11 (5% discount for BIS)
7.1(Chemical Composition - Sulphur - Laddle Analysis IS 228)	-	2000	-

Complete

-
-

IS 778 (1984)

Specification for 2010 copper alloy gate, globe and check valves for waterworks purposes (Fourth Revision)

Solid wedge type, spigot wedge type, double disc type,

4400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Nominal Sizes )	-	3200	(For complete dimensional testing)
9.5-Table 13(Seat Test ( Hydrostatic))	-	1200	(5% discount for BIS)
5(Types)	-	3200	(For complete dimensional testing)
4(Classification )	-	3200	(For complete dimensional testing)
7.1(Valve Bodie - IS 778)	-	3200	(For complete dimensional testing)
7.1.1(Body End Ports -IS 778)	-	3200	(For complete dimensional testing)
7.1.2(Water-Way Area - IS 778)	-	3200	(For complete dimensional testing)
7.1.3(Screwed Body End -IS 778)	-	3200	(For complete dimensional testing)
7.1.3.1(Screwed Body End -IS 778)	-	3200	(For complete dimensional testing)
7.1.3.1(Threads - IS 554)	-	3200	(For complete dimensional testing)
7.1.3.1-Table2(length of threaded portion in screwed end valves - IS 778)	-	3200	(For complete dimensional testing)
7.1.3.1(Thread -IS 778)	-	3200	(For complete dimensional testing)
7.1.3.1(Screwed Body End -IS 778)	-	3200	(For complete dimensional testing)
7.1.4(Flanged Body End IS 778)	-	3200	(For complete dimensional testing)
7.1.4.1- Table 3(Diameter of flange - IS 778)	-	3200	(For complete dimensional testing)
7.1.4.1- Table 3(Thickness of flange - IS 778)	-	3200	(For complete dimensional testing)
7.1.4.1- Table 3(Diameter of Belt circle -IS 778)	-	3200	(For complete dimensional testing)
7.1.4.1- Table 3(No. of holes - IS 778)	-	3200	(For complete dimensional testing)
7.1.4.1- Table 3(Diameter of holes -IS 778)	-	3200	(For complete dimensional testing)
7.1.4.1(Holes in flange - IS 778)	-	3200	(For complete dimensional testing)
7.1.5(Wedge and Disc Guides in the Bodies of Gate Valves - IS 778)	-	3200	(For complete dimensional testing)
7.2.1(Bonnets - IS 778)	-	3200	(For complete dimensional testing)
7.2.1.1(Bonnets - IS 778)	-	3200	(For complete dimensional testing)
7.2.1.2(number of engaged threads - IS 778)	-	3200	(For complete dimensional testing)
7.2.1.2(pitch of threads - IS 778)	-	3200	(For complete dimensional testing)
7.2.1.3(Bonnets - IS 778)	-	3200	(For complete dimensional testing)
7.2.2(Bonnet Flanges - IS 778)	-	3200	(For complete dimensional testing)
7.2.3(Bonnet Bolting - IS 778)	-	3200	(For complete dimensional testing)
7.3(Stuffing Box - IS 778)	-	3200	(For complete dimensional testing)
7.4(Gland - IS 778)	-	3200	(For complete dimensional testing)
7.4.1(Gland nut - IS 778)	-	3200	(For complete dimensional testing)
7.5(Back Seat- IS 778)	-	3200	(For complete dimensional testing)
7.6.1(Stem - IS 778)	-	3200	(For complete dimensional testing)
7.6.2(Threads of Stem - IS 778)	-	3200	(For complete dimensional testing)
7.6.3(actuating threads - IS 778)	-	3200	(For complete dimensional testing)
7.6.4(Length of Stem - IS 778)	-	3200	(For complete dimensional testing)
7.6.5(Upper end of Stem - IS 778)	-	3200	(For complete dimensional testing)
7.6.6(Rising Stem - IS 778)	-	3200	(For complete dimensional testing)
7.6.6.1(Rising Stem - IS 778)	-	3200	(For complete dimensional testing)
7.6.7(Non-rising Stem - IS 778)	-	3200	(For complete dimensional testing)
7.7.1(Wedge-IS 778)	-	3200	(For complete dimensional testing)
7.7.2(Wedge-IS 778)	-	3200	(For complete dimensional testing)
7.7.3(Double disc - IS 778)	-	3200	(For complete dimensional testing)
7.7.3.1(Spreading assembly - IS 778)	-	3200	(For complete dimensional testing)
7.7.3.2(Disc - IS 778)	-	3200	(For complete dimensional testing)
7.8(Disc Assembly for Globe Valves - IS 778)	-	3200	(For complete dimensional testing)
7.8.1(One-Piece Disc - IS 778)	-	3200	(For complete dimensional testing)
7.8.1(One-Piece Disc - IS 778)	-	3200	(For complete dimensional testing)
7.8.1(One-Piece Disc - IS 778)	-	3200	(For complete dimensional testing)
7.8.1(One-Piece Disc - IS 778)	-	3200	(For complete dimensional testing)
7.8.1(One-Piece Disc - IS 778)	-	3200	(For complete dimensional testing)
7.8.2(Renewable Disc Assembly - IS 778)	-	3200	(For complete dimensional testing)
7.9(Disc for Check Valves - IS 778)	-	3200	(For complete dimensional testing)
7.9(Disc for Check Valves - IS 778)	-	3200	(For complete dimensional testing)
7.9.1(Disc of glove and Check Valves - IS 778)	-	3200	(For complete dimensional testing)
7.10.1(Body Seats - IS 778)	-	3200	(For complete dimensional testing)
7.10.1(Seat ring - IS 778)	-	3200	(For complete dimensional testing)
7.11(Handwheel - IS 778)	-	3200	(For complete dimensional testing)
7.11(Handwheel - IS 778)	-	3200	(For complete dimensional testing)
8.1- Table 4(Thickness of Body and Bonnet- IS 778)	-	3200	(For complete dimensional testing)
8.2 - Table 5(Flat to Flat size -IS 778 )	-	3200	(For complete dimensional testing)
8.3 - Table 6(Width of end - IS 778)	-	3200	(For complete dimensional testing)
8.4 - Table 7(Stem Diameters - IS 778)	-	3200	(For complete dimensional testing)
8.5 - Table 8(Size of packing space - IS 778)	-	3200	(For complete dimensional testing)
8.6- Table 9 to Table 12(End to end/ centre to ends/ Face to face/Centre to face dimension )	-	3200	(For complete dimensional testing)

Complete

-
-

IS 13095 (1991)

Butterfly valves for general purposes

For size 50 to 500 mm only

4900 View breakup
4900/- (5% Discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6( NOMINAL SIZES )	-	2500	(5% discount for BIS)
9.1.1 ( Double Flanged Body Ends)	-	800	(5% discount for BIS)
17.1(Performance Testing)	-	1600	(5% discount for BIS)

Complete

-
For size 50 to 500mm only

IS 1363 : Part 3 (2018)

Hexagon Head Bolts, Screws and Nuts of Product Grade ˜C ™ Part 3 (Style 1) Hexagon Nuts ( Size Range M 5 to M 64 ) ( Fifth Revision )

For M8, M10, M12, M16, M20, M24, M30, M36, M39 only

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3-Table 1(Dimensions-D)	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-P)	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-dw(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-e(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-m(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-m(maximum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-mw(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-s(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 1(Dimensions-s(maximum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-D)	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-P)	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-dw(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-e(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-m(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-m(maximum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-mw(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-s(minimum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
3-Table 2(Dimensions-s(maximum))	-	1300	For complete Cl 4 (Dimension 450 + Chem: 850)
4-Table 3(General requirements)	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Threads-ISO 724 & 965(1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Property class (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Tensile strength (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Lower yield strength (ISO 898-1) )	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress at 0,2 % non-proportional elongation (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress at 0,0048d non-proportional elongation for full-size fasteners (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress under proof load (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Proof strength ratio (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Percentage elongation after fracture for machined test pieces (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Percentage reduction of area after fracture for machined test pieces (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Elongation after fracture for full-size fasteners (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Head soundness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Vickers hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Brinell hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Non-carburization (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Height of non-decarburized thread zone (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Depth of complete decarburization in the thread (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Reduction of hardness after retempering (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Breaking torque (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Impact strength (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Quench Cracks(ISO 6157-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging cracks (ISO 6157-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screw (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Circular head screws (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Circular head screws (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Raw material seams and laps (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Voids (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Folds (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Tool marks (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-- Quench cracks (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks - (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Width (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Depth (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Raw material, seams and laps- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Voids- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Folds- (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Tool marks - (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	250	Cl 4 Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Damages - (ISO 6157-3))	-	250	Cl 4 Surface Integrity

Complete

-
-

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

4200 View breakup
Rs.4200/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 12(Length, Width & Thickness)	-	1450	-
Cl 8(UTM)	-	1250	-
Cl 9(Press)	-	1500	-

Complete

-
0.0

IS 14846 (2000)

Sluice valve for water works purposes (50 To 1200 mm size) - specification

For Size 50 to 600 mm only

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Nominal Sizes)	-	3550	For complete Sizes, Dimensions and Visual aspects
5.1.1(Actual Bore)	-	3550	For complete Sizes, Dimensions and Visual aspects
10.1 Annex B-1(Hydraulic Test)	-	1200	-
10.2(Flaw Detection Test for Stems)	-	750	--
9(Coating)	-	750	-
4(Nominal Pressures)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.2.1(Manufacture - Bodies and Bonnets)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	3550	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	3550	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	3550	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	3550	For complete Sizes, Dimensions and Visual aspects
7.11(Hand Wheel)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.11(Hand Wheel)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.11(Hand Wheel)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.12(Valve Caps)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.12(Valve Caps)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.12(Valve Caps)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 1(Flanges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 2(Flanges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 3(Flanges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 4(Flanges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 5(Flanges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 6(Flanges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.4.1(Wedges )	-	3550	For complete Sizes, Dimensions and Visual aspects
7.4.1(Wedges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.4.1(Wedges)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.5(Guides and Lugs)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.5(Guides and Lugs)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.7.2(Stem and Wedge Nuts)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.7.4(Stem and Wedge Nuts)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.7.3(Stem and Wedge Nuts)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.1(Gears)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.14(By Pass Arrangements)	-	3550	For complete Sizes, Dimensions and Visual aspects
10.1 Annex B-2(Hydraulic Test)	-	1200	-
7.5(Guides and Lugs)	-	3550	For complete Sizes, Dimensions and Visual aspects
7.5.1(Guides and Lugs)	-	3550	For complete Sizes, Dimensions and Visual aspects

Complete

-
-

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

4200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8 & Table 3(UTM)	-	1750	-
Cl 9(Press)	-	1000	-
Cl 12 & 13(Length, Width & Thickness)	-	1450	-
7.1(Carbon %)	-	4200	Complete sample testing charges
7.1(Manganese %)	-	4200	Complete sample testing charges
7.1(Phosphorus %)	-	4200	Complete sample testing charges
7.1(Sulphur %)	-	4200	Complete sample testing charges
7.1(Silicon %)	-	4200	Complete sample testing charges
7.1( Copper %)	-	4200	Complete sample testing charges
7.1( Aluminium %)	-	4200	Complete sample testing charges
7.1( Nb)	-	4200	Complete sample testing charges
7.1( Ti)	-	4200	Complete sample testing charges
7.1(Cr)	-	4200	Complete sample testing charges
7.1(Mo)	-	4200	Complete sample testing charges
7.1(Ni)	-	4200	Complete sample testing charges

Complete

-
-

IS 9890 (1981)

Specification for general purpose ball valves

4450 View breakup
4450/- (5% Discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Nom. size. )	-	2450	(5% discount for BIS)
5(End connections)	-	750	(5% discount for BIS)
11(Inspection & Test)	-	1250	(5% discount for BIS)

Complete

-
0.0

IS 9523 (2000)

Ductile iron fittings for pressure pipes for water, gas and sewage - Specification (First Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(Thickness)	-	3000	For complete dimensional tests, design and tolerance.
Cl 9(Tensile Test & Hardness Test)	-	1750	For tensile and hardness test
Cl 10(Hydrostatic Test)	-	2500	-
Cl 11(Nominal Diameter, Ovality, Dimensions, No. Of Holes & Bolt Sizes)	-	3000	For complete dimensional tests
Cl 13(Coating)	-	250	-
Cl 6 & Table 4,5,6&7(Design & Tolerance)	-	3000	For complete dimensional tests, design and tolerance.
Cl 6 & Table 4,5,6&7(Design & Tolerance)	-	3000	For complete dimensional tests, design and tolerance.
Cl 9(Tensile Test & Hardness Test)	-	1750	For tensile and hardness test

Complete

-
-

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

For Size 63.5 mm, 76.1mm, 88.9mm only

5000 View breakup
5000/-0(5% Discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13.1.1(Ovality)	-	1500	For Cl 11.2, 13 & 9 (5% discount for BIS)
13.1.2(Eccentricity)	-	1500	For Cl 11.2, 13 & 9 (5% discount for BIS)
9.1 Table 2(Outside Diameter)	-	1500	For Cl 11.2, 13 & 9 (5% discount for BIS)
9.1 Table 2(Thickness)	-	1500	For Cl 11.2, 13 & 9 (5% discount for BIS)
9.1 Table 2(Mass)	-	1500	For Cl 11.2, 13 & 9 (5% discount for BIS)
8.1.1 Table 1(Tensile Strength- IS 1608(1))	-	750	For complete Cl 8.1 (5% discount for BIS)
8.1.1 Table 1(Yield Strength- IS 1608)	-	750	For complete Cl 8.1 (5% discount for BIS)
8.1.1 Table 1(Elongation Percent- IS 1608)	-	750	For complete Cl 8.1 (5% discount for BIS)
8.2(Drift Expansion Test- IS 2335)	-	750	(5% discount for BIS)
8.3(Flattening Test- IS 2328)	-	500	(5% discount for BIS)
10(Hardness)	-	250	(5% discount for BIS)
15.1(Straightness)	-	250	(5% discount for BIS)
7.1(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	1000	For complete Cl 7.1 (5% discount for BIS)
7.1(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	1000	For complete Cl 7.1 (5% discount for BIS)

Complete

-
For size 63.5mm, 76.1mm, 88.9mm only

IS 8794 (1988)

Specification for cast iron detachable joints for use with asbestos cement pressure pipes (First Revision)

3500 View breakup
3500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1, Table 4(Mass of joints)	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
8.4(Coating)	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
6.1, Table 2(External Dia of AC Pipe(D2))	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
6.1, Table 2(Inside diaFlange(DI))	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
6.1, Table 2(External Dia at Centre(DEC))	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
6.1, Table 2(Collar Width(Wc))	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
6.1, Table 2(Thickness(t))	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
6.1, Table 3(Nominal Dia of Bolt(do))	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300
6.1, Table 3(Minimum prefared length of bolt(L))	-	3500	For Cl 6 & 7: 1200 For Cl 5: 1000 For Cl 4.1: 1000 For Cl 4.2: 300

Complete

-
0.0

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Nominal Diameter & Out Of Shape)	-	4000	-
Cl 8(Workmanship)	-	500	-
6.1(Carbon %)	-	500	For complete chemical testing
6.1(Manganese %)	-	500	For complete chemical testing
6.1(Phosphorus %)	-	500	For complete chemical testing
6.1(Silicon %)	-	500	For complete chemical testing
6.1( Aluminium %)	-	500	For complete chemical testing

Complete

-
-

IS 7452 (1990)

Hot rolled steel sections for doors, windows and ventilators - Specification

2000 View breakup
Rs.2000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 6(Dimensions)	-	1500	For Complete Cl 6 & Cl 7: 1500
cl 7(MASS AND MASS TOLERANCE)	-	1500	For Complete Cl 6 & Cl 7: 1500
cl 9(BEND TEST)	-	500	-

Complete

-
0.0

IS 7181 (1986)

Specification for horizontally cast iron double flanged pipes for water, gas and sewage (First Revision)

9750 View breakup
Rs.9750/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Tensile Test)	-	1500	-
6.1(Hydrostatic Test)	-	3500	-
7.1(Sizes and Mass)	-	3500	For Complete Cl 7 & Cl 8
7.2(Sizes and Mass)	-	3500	For Complete Cl 7 & Cl 8
7.3(Sizes and Mass)	-	3500	For Complete Cl 7 & Cl 8
7.4(Sizes and Mass Dimensions of Flange)	-	3500	For Complete Cl 7 & Cl 8
8.5(Permissible Deviation from a Straight Line)	-	3500	For Complete Cl 7 & Cl 8
9(Coating)	-	750	-

Complete

-
INCLUDED W.E.F. 28-10-2020.

IS 6603 (2001)

Stainless steel bars and flats - Specification (First Revision)

3200 View breakup
Rs.3200/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.3, Table 3(Elongation ,Percent)	-	1400	For all Mechanical Tests : 1400
9.5, Table 3(Charpy Impact Test, J-IS 1499)	-	1400	For all Mechanical Tests : 1400
9.1, Table 3(0.2 Percent Proof Stress, MPa)	-	1400	For all Mechanical Tests : 1400
9.2, Table 3(Tensile Strength, MPa)	-	1400	For all Mechanical Tests : 1400
9.4, Table 3(Annealed Hardness, HB-IS 1500: Pt 1)	-	1400	For all Mechanical Tests : 1400
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Carbon -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Silicon- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Manganese- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Nickel -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Chromium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Molybdenum- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Titanium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Niobium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Sulphur- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Phosphorus- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1(Others (Nitrogen)- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-	1800	For all Chemical Tests : 1800
12(Dimensions & Tolerances, mm-IS 6603)	-	1400	For all Mechanical Tests : 1400
12(Diameter, mm)	-	1400	For all Mechanical Tests : 1400
12(Out of Round , mm)	-	1400	For all Mechanical Tests : 1400
12(Length , mm)	-	1400	For all Mechanical Tests : 1400
12(Variation in Straightness)	-	1400	For all Mechanical Tests : 1400
Cl.14.1(Corrosion Resistance- IS 10461(Part1))	-	1800	For all Chemical Tests : 1800

Complete

-
0.0

IS 5312 : Part 1 (2004)

Swing Check Type Reflux (Non-Return] Valves for Water Works Purposes - Part 1 : Single-Door Pattern

For Size 50 to 600mm only

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Nominal Sizes)	-	4000	For Dimensions and Manufacturer
4.1.1(Actual bore)	-	4000	For Dimensions and Manufacturer
7.1(Coating)	-	4000	For Dimensions and Manufacturer
7.2(Coating)	-	4000	For Dimensions and Manufacturer
8.2(Hydrostatic Body Test )	-	1500	For complete Hydrostatic
8.3(Hydrostatic Seat Test)	-	1500	For Complete Hydrostatic Test-
6.2(Manufacture Dimensions Table 2 )	-	4000	For Dimensions and Manufacturer
6.2(Manufacture Dimensions Table 2 )	-	4000	For Dimensions and Manufacturer
6.4(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.5(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.6(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.7(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.8(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.8.1(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.9(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.10(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.10.1(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.9(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.9(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.9(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.9(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.5(Manufacture )	-	4000	For Dimensions and Manufacturer clauses
6.12(Door Faces)	-	4000	For Dimensions and Manufacturer clauses
6.13(By-pass arrangements)	-	1500	For Complete Hydrostatic Testing
3(Nominal Pressure)	-	4000	For Dimensions and Manufacturer clauses

Complete

-
-

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

4200 View breakup
Rs.4200/- (5% Discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11 & 12(DIMENSIONS and Tolerances)	-	2100	For cl. 11 & 12
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	For Complete Cl 6
Cl. 6.1, Table 1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1900	`For Complete Cl 6
9( FREEDOM FROM DEFECTS)	-	200	-

Complete

-
0.0

IS 2692 (1989)

Ferrules for water services ? specification

Except 8 mm, 10 mm

4500 View breakup
Rs.4500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Nominal Size )	-	1600	For complete cl 4
4.1.1(Nominal Size )	-	1600	For complete cl 4
8.6(Plug)	-	1200	For complete cl 8
10(Testing)	-	1700	-
8.8(Srew Threads)	-	1200	For complete cl 8
8.8(Srew Threads)	-	1200	For complete cl 8
8.8(Srew Threads)	-	1200	For complete cl 8

Complete

-
Except 8mm, 10mm

IS 2202 : Part 1 (1999)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1( Squareness Test - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Variation in thickness - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Thickness - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Width- IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Height - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.2( Twist, cupping & wrapping - IS 4020 (Pt-3))	-	1000	For Cl 11.2
11.3(Depth of deviation - IS 4020(Pt-4))	-	1000	For Cl 11.3
11.4(Depth of indentation - IS 4020(Pt-5))	-	1000	For Cl 11.4
11.4(Impact Indentation Test - IS 4020(Pt-5))	-	1000	For Cl 11.4
11.5(Residual deflection - IS 4020(Pt-6))	-	2000	For Cl 11.5
11.5(Deflection at maximum load - IS 4020(Pt-6))	-	2000	For Cl 11.5
11.6(Residual lateral buckling - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.6(Lateral buckling during loading - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.6(Residual deflection after removal of load - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.6(Deflection of the edge at maximum load - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	2000	For Cl 11.7
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	2000	For Cl 11.7
11.8(Residual deformation after 15 minutes of unloading - IS 4020(Pt-9))	-	2000	For Cl 11.8
11.8(Initial deflection - IS 4020(Pt-9))	-	2000	For Cl 11.8
11.8(Buckling Test - IS 4020(Pt-9))	-	2000	For Cl 11.8
11.9(Slamming Test - IS 4020(Pt-10))	-	750	For Cl 11.9
11.1(Misuse Test - IS 4020(Pt-11))	-	750	For Cl 11.10
11.11(The recovery of the original size after subjecting the door to high and low humidity- IS 4020(Pt-12))	-	9750	For Cl 11.11
11.11(Maximum departure from the general planeness - IS 4020(Pt-12))	-	9750	For Cl 11.11
11.11(Varying Humidity Test - IS 4020(Pt-12))	-	9750	For Cl 11.11
11.12(End Immersion Test - IS 4020(Pt-13))	-	1000	For Cl 11.12
11.13(Knife Test - IS 4020(Pt-14))	-	500	For Cl 11.13
11.14(Glue Adhesion Test - IS 4020(Pt-15))	-	750	For Cl 11.14
11.15(Screw Withdrawal Strength - IS 4020 (Pt-16))	-	750	For Cl 11.15
11.15(Screw Withdrawal Resistance test - IS 4020 (Pt-16))	-	750	For Cl 11.15
9.1(Workmanship & finish - IS 2202(Pt-1))	-	250	For complete Cl 9
9.2(Workmanship & finish - IS 2202(Pt-1))	-	250	For complete Cl 9
9.3(Workmanship & finish - IS 2202(Pt-1))	-	250	For complete Cl 9

Complete

-
-

IS 1879 (2010)

Malleable cast iron pipe fittings - Specification (Third Revision)

Except 1/8", 1/4" and 8"

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 - Table 4 to Table 27(a - IS 1879)	-	2500	For complete cl 7
7.1 - Table 4 to Table 27(b - IS 1879)	-	2500	For complete cl 7
7.1 - Table 4 to Table 27(c- IS 1879)	-	2500	For complete cl 7
7.1 - Table 4 to Table 27(d- IS 1879)	-	2500	For complete cl 7
7.1 - Table 28(d -IS 1879)	-	2500	For complete cl 7
7.1 - Table 28(D - IS 1879)	-	2500	For complete cl 7
7.2- Table 2(Wall thickness of fittings - IS 1879)	-	2500	For complete cl 7
8.1(Thread -IS 554)	-	750	For complete cl 8
8.2(Alignment of threads -IS 554)	-	750	For complete cl 8
11(Pressure Test)	-	2000	-
12(Compression Test)	-	2000	-
10.i)(Mass of Galvanized coating )	-	250	For complete cl 10
10.ii)( Uniformity of Galvanized coating-IS 2633)	-	250	For complete cl 10
6.1(Tensile Strength - IS 14329)	-	1500	For tensile and elongation
6.1(Elongation - Is 14329)	-	1500	For tensile and elongation

Complete

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

Except Pull out test

10800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6.1(Length, Width & Thickness)	-	3000	For Cl 6 & 7 testing charges will be Rs. 3000
Cl 7.2(Weight)	-	3000	For Cl 6 & 7 testing charges will be Rs. 3000
Cl 5(Deformations and Surface Characteristics)	-	2000	-
Cl 8.1(UTM)	-	3000	For Cl 8 & 9 testing charges will be Rs. 3000
Cl 9.3(Load In One Direction)	-	3000	For Cl 8 & 9 testing charges will be Rs. 3000
Cl 9.4(Load In Other Direction From Bend)	-	3000	For Cl 8 & 9 testing charges will be Rs. 3000

Complete

-
-

IS 1363 : Part 1 (2019)

Hexagon Head Bolts, Screws and Nuts of Product Grade ‘C’ Part 1 Hexagon Head Bolts ( Size Range M 5 to M 64 ) ( Fifth Revision )

For M8, M10,M12,M16,M20,M24,M30,M36,M39 only

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3-Table 1(Dimensions-d)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-p)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-b)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-c(Maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-da(Maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-ds(Minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-ds(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-dw(minimum))	-	1350	`For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-e(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-k(nominal))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-k(Minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-k(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-kw(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-r(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-s(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-s(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-l(nominal))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-l(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-l(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-ls(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-lg(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-β)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 1(Dimensions-u)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-d)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-p)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-b)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-c(Maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-da(Maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-ds(Minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-dw(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-e(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-k(nominal))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-k(Minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-kw(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-r(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-s(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-s(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-l(nominal))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-l(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-l(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-ls(minimum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-lg(maximum))	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-β)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
3-Table 2(Dimensions-u)	-	1350	For complete Cl 4 (Dimension 450 + Chem: 900)
4-Table 3(General requirements-ISO 8992)	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Threads-ISO 724 & 965(1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Property class (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Tensile strength (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Lower yield strength (ISO 898-1) )	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress at 0,2 % non-proportional elongation (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress at 0,0048d non-proportional elongation for full-size fasteners (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress under proof load (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Proof strength ratio (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Percentage elongation after fracture for machined test pieces (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Percentage reduction of area after fracture for machined test pieces (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Elongation after fracture for full-size fasteners (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Head soundness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Vickers hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Brinell hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface hardness (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Non-carburization (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Height of non-decarburized thread zone (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Depth of complete decarburization in the thread (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Reduction of hardness after retempering (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Breaking torque (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Impact strength (ISO 898-1))	-	900	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Quench Cracks(ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging cracks (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screw (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Circular head screws (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Circular head screws (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Raw material seams and laps (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Voids (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Folds (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Tool marks (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-- Quench cracks (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks - (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Width (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Depth (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Raw material, seams and laps- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Voids- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Folds- (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Tool marks - (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	250	Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Damages - (ISO 6157-3))	-	250	Surface Integrity

Complete

-
-

Bureau of Indian Standards

The National Standards Body of India

JBS TESTING SOLUTIONS JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 [email protected]

Scope List