BIS - LIMS (Laboratory Information Management System)

Delhi Analytical Research Laboratory

PLOT NO-2, TIMBER BLOCK, JHILMIL INDUSTRIAL AREA NEAR DILSHAD GARDEN METRO STATION, NEW Delhi, East, Delhi, 110095

9717324010 [email protected]

Scope List

Reset

13 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

63 to 315 mm

22200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	100	10% discount to BIS
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	100	10% discount to BIS
6.1.3 (Length of Pipe)	-	100	10% discount to BIS
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	100	10% discount to BIS
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	100	10% discount to BIS
7.1(Appearance:- )	-	100	10% discount to BIS
7.2(Colour )	-	100	10% discount to BIS
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1000	10% discount to BIS
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1000	10% discount to BIS
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	800	10% discount to BIS
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	2000	10% discount to BIS
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1500	10% discount to BIS
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1500	10% discount to BIS
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1500	10% discount to BIS
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	500	10% discount to BIS
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1500	10% discount to BIS
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	1500	10% discount to BIS
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1500	10% discount to BIS
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	100	-10% discount to BIS
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	100	10% discount to BIS
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	100	10% discount to BIS
6.1.4, Table 3(iv) Length of spigot, l1)	-	100	10% discount to BIS
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	150	10% discount to BIS
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	100	10% discount to BIS
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	100	10% discount to BIS
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	150	10% discount to BIS
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	100	10% discount to BIS
6.1.4.1 (e3min=0.75e)	-	100	10% discount to BIS
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	8000	10% discount to BIS
9.2 IS 14182(b) Solvent cement)	-	3000	10% discount to BIS
'7.5 (amdt.7)(Effect on Water (Type test))	-	3500	10% discount to BIS

Complete

-
-

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

Up to 355 mm

2250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table-1 Fig.1(Dimension of Socket length)	-	100	10% discount to BIS
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	100	10% discount to BIS
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	100	10% discount to BIS
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	200	10% discount to BIS
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	500	10% discount to BIS
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	1250	10% discount to BIS

Complete

-
-

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

12 to 25 mm

12400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.2(Fittings)	-	500	10% discount to BIS
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	800	10% discount to BIS
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	800	10% discount to BIS
8.2.2(Regulated Emitting Pipes)	-	800	10% discount to BIS
8.3.1(Wall Thickness ofEmitting Pipe)	-	200	10% discount to BIS
8.3.2(Inside Diameter ofEmitting Pipe)	-	300	10% discount to BIS
8.3.3(Flow Paths in Emitting Unit)	-	300	10% discount to BIS
8.3.4(Spacing ofEmitter Units)	-	200	10% discount to BIS
8.5(Resistance to Tension at Elevated Temperature)	-	1500	10% discount to BIS
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	1500	10% discount to BIS
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1500	10% discount to BIS
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1500	10% discount to BIS
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1500	10% discount to BIS
8.8(Determination of Emitting Unit Exponent)	-	1500	10% discount to BIS
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	700	10% discount to BIS
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	1500	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	500	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	700	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	1000	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	1000	10% discount to BIS
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	800	10% discount to BIS
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1500	10% discount to BIS
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1500	10% discount to BIS

Complete

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

Up to 355 mm

8700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Colour)	-	100	10% discount to BIS
6(Dimensions of pipes)	-	100	10% discount to BIS
7(Visual Appearance)	-	100	10% discount to BIS
8.1(Hydraulic characteristics)	-	3500	10% discount to BIS
8.2(Reversion)	-	1000	10% discount to BIS
8.3(Density)	-	500	10% discount to BIS
8.4(Melt Flow Rate)	-	1000	10% discount to BIS
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	700	10% discount to BIS
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	10% discount to BIS
3(Designation)	-	3300	10% discount to BIS and This charges Either for resin or for Resin with master batch applicable.

Complete

-
-

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

Up to 200 mm

24200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1 (Visual and Workmanship Requirement)	-	200	10% discount to BIS
6.1.3.1.1(Weldability Test)	-	3000	10% discount to BIS
6.1.2.2( Hydraulic Proof Test)	-	10000	10% discount to BIS
6.1.1, 6.1.1.1(Leakage Test)	-	2000	10% discount to BIS
5.3(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	500	10% discount to BIS
4.1.4(a)(Holding Attachments for Coupler Parts)	-	2500	10% discount to BIS
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	1000	10% discount to BIS
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	10% discount to BIS
Cl 4.1.5(Rubber rings- B) Change in hardness)	-	4000	10% discount to BIS

Complete

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

Up to 200 mm

16300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table -1(DIMENSIONS OF PIPES)	-	200	10% discount to BIS
5.1.2(Ovality)	-	200	10% discount to BIS
6.1(VISUAL APPEARANCE)	-	100	10% discount to BIS
7.1 Table -2(Hydraulic Characteristics)	-	5000	10% discount to BIS
7.2(Reversion Test)	-	1500	10% discount to BIS
7.3(Tensile Test)	-	1500	10% discount to BIS
7.4table-2(Fusion Compatibility Test)	-	4000	10% discount to BIS
7.5(Density)	-	500	10% discount to BIS
7.6(Melt now Rate (MFR))	-	1500	10% discount to BIS
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	1000	10% discount to BIS
(Cl.4.2)(Carbon black- a)carbon content)	-	1000	10% discount to BIS
Cl.5(Dimensions of pipe - ii) Wall thickness maximum)	-	200	10% discount to BIS
Cl.5(Dimensions of pipe - i) Outside diameter)	-	100	10% discount to BIS

Complete

-
-

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

40 to 160 mm

12800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Colour of fittings)	-	100	10% discount to BIS
7.1,Table 1(Wall thickness)	-	300	10% discount to BIS
7.2 ,Table 2&3(Socket Dimensions)	-	400	10% discount to BIS
8(Sealing Rings)	-	500	10% discount to BIS
10(Workmanship)	-	100	10% discount to BIS
12.1(Visual appearance)	-	100	10% discount to BIS
12.2(Stress relief test)	-	1000	10% discount to BIS
12.3(Vicat softening tempewrature)	-	1200	10% discount to BIS
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	1000	10% discount to BIS
Cl.15, Annex B(Sulphated Ash Content)	-	700	10% discount to BIS
16.1(Impact test)	-	1000	10% discount to BIS
17(Watet tightness of joint)	-	1500	10% discount to BIS
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1500	10% discount to BIS
5(Colour of fittings)	-	0	-
7.1,Table 1(Wall thickness)	-	0	-
7.2 ,Table 2&3(Socket Dimensions)	-	0	-
8(Sealing Rings)	-	0	-
10(Workmanship)	-	0	-
12.1(Visual appearance)	-	0	-
12.2(Stress relief test)	-	0	-
12.3(Vicat softening tempewrature)	-	0	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	0	-
Cl.15, Annex B(Sulphated Ash Content)	-	0	-
16.1(Impact test)	-	0	-
17(Watet tightness of joint)	-	0	-
Cl.14, Annex A(Titanium Di-Oxide Content)	-	0	-
7.3(Dimensions of waste trap(Nahani Trap)	-	500	10% discount to BIS
11.4,Table 5(Vent cowl)	-	500	10% discount to BIS

Complete

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

40 to 315 mm

39700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	100	10% discount to BIS
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1500	10% discount to BIS
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	100	10% discount to BIS
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	100	10% discount to BIS
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	100	10% discount to BIS
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	100	10% discount to BIS
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	1500	10% discount to BIS
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	2000	10% discount to BIS
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	1500	10% discount to BIS
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1000	10% discount to BIS
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1500	10% discount to BIS
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	10% discount to BIS
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	20200	10% discount to BIS
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1000	10% discount to BIS
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1500	10% discount to BIS
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	200	10% discount to BIS
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	800	10% discount to BIS
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	1500	10% discount to BIS
8.6(Effect on Water Test)	-	3000	10% discount to BIS

Complete

-
-

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

Up to 150 mm

101600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	25000	10% discount to BIS
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	500	10% discount to BIS
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	200	10% discount to BIS
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	200	10% discount to BIS
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	200	10% discount to BIS
7.1.3 (Effective length)	-	200	10% discount to BIS
8(Pipe Ends)	-	200	10% discount to BIS
9.1(Visual Appearance)	-	200	10% discount to BIS
9.2 IS 12235 (Part 3)(Opacity)	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	1000	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	1000	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	500	10% discount to BIS
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	800	10% discount to BIS
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	800	10% discount to BIS
9.6 IS 12235(Part 14)(Density)	-	500	10% discount to BIS
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	27100	10% discount to BIS
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1200	10% discount to BIS
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1000	10% discount to BIS
7.1.3 (Effective length)	-	0	10% discount to BIS
6.2.1 Annex B(Chloride Content of Resin)	-	1000	10% discount to BIS
6.3(Compound Properties)	-	10000	10% discount to BIS
6.3.1 Annex B(Chloride content)	-	1000	10% discount to BIS
9.1(Visual Appearance)	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1500	10% discount to BIS
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	35000	10% discount to BIS
10.4 IS 12235(Part 19)(Flattening Test)	-	2000	10% discount to BIS

Complete

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

UP TO 400 MM

16200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(COLOUR)	-	100	10% discount to BIS
9.1( Visual Appearance)	-	100	10% discount to BIS
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	100	10% discount to BIS
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	200	10% discount to BIS
7.4 Table 8 & 9 Fig 1(Segmental length, l5)	-	100	10% discount to BIS
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	200	10% discount to BIS
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	100	10% discount to BIS
7.3.1(No.of Ribs)	-	100	10% discount to BIS
7.3.2(Rib height)	-	100	10% discount to BIS
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	200	10% discount to BIS
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	200	10% discount to BIS
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	200	10% discount to BIS
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	2000	10% discount to BIS
8.4(Sealing rings - Hardness)	-	500	10% discount to BIS
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	5000	10% discount to BIS
9.5(Tensile Strength IS 12235(Part 13))	-	1500	10% discount to BIS
9.3(Density IS 12235 (Part 14))	-	500	10% discount to BIS
9.2(Internal Diameter)	-	100	10% discount to BIS
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1500	10% discount to BIS
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	1000	10% discount to BIS
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	200	10% discount to BIS
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	1000	10% discount to BIS
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	200	10% discount to BIS
4.1.2(K-Value as per IS-4669)	-	1000	10% discount to BIS

Complete

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

12-32 MM

12700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	200	10% discount to BIS
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	200	10% discount to BIS
6.1(Visual Appearance)	-	100	10% discount to BIS
7.3(Tensile Test)	-	1200	10% discount to BIS
7.3(Elongation at Break)	-	1200	10% discount to BIS
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1800	10% discount to BIS
7.2(Reversion Test)	-	1000	10% discount to BIS
7.1(Hydraulic Characteristics)	-	4000	10% discount to BIS
4.1.c.iii (Volatile matter - Annex B )	-	1000	10% discount to BIS
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	0	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0	-
6.1(Visual Appearance)	-	0	-
7.3(Tensile Test)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
7.2(Reversion Test)	-	0	-
7.1(Hydraulic Characteristics)	-	0	-
4.1.c.iii (Volatile matter - Annex B )	-	0	-
4.1.a (Potyethylene - higher olefins constituent )	-	1000	10% discount to BIS
4.1.b(Potyethylene - anti-oxidant)	-	1500	10% discount to BIS
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	700	10% discount to BIS
Cl. 4.2(Carbon Black Content)	-	700	10% discount to BIS
Cl. 4.2(Carbon Black Dispersion)	-	700	10% discount to BIS
4.1.c.i (Density)	-	500	10% discount to BIS
4.1.c.ii (Toluene extract - Annex A)	-	1000	10% discount to BIS
4.1.c.iii (Volatile matter - Annex B )	-	0	-
Cl. 5.0 & 5.1 Table -1(Outside Diameter)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	0	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1500	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	2500	-
7.2(Reversion Test)	-	0	10% discount to BIS
7.3(Tensile Test)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
8.0 (8.1) (Supply of pipes )	-	100	10% discount to BIS
9.0 (9.1)(Coiling )	-	500	10% discount to BIS

Complete

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

20 to 355 mm

20100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(DIMENSIONS-PIPE-Nominal Diameter)	-	0	-
7.2.1(DIMENSIONS-Socket)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	0	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	0	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	0	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	-
11.2(Resistance to External Blows at 0°C)	-	0	-
Clause 10.7(Sulphated Ash Content)	-	0	-
10.1(Colour)	-	0	-
6.1.2(PVC Resin)	-	5000	10% Discount For BIS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	100	10% Discount For BIS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	100	10% Discount For BIS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	100	10% Discount For BIS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	100	10% Discount For BIS
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	100	10% Discount For BIS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	100	10% Discount For BIS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	100	10% Discount For BIS
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	100	10% Discount For BIS
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	300	10% Discount For BIS
7.1.4(Length)	-	100	10% Discount For BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	100	10% Discount For BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	100	10% Discount For BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	100	10% Discount For BIS
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	100	10% Discount For BIS
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	100	10% Discount For BIS
7.2.1.1 Table3(Angle of taper (Note-1))	-	100	10% Discount For BIS
8(SEALING RINGS)	-	500	10% Discount For BIS
9.1(PIPE ENDS)	-	100	10% Discount For BIS
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	100	10% Discount For BIS
10.1(Colour)	-	100	10% Discount For BIS
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	10% Discount For BIS
10.3(Effect on Water Test)	-	3000	10% Discount For BIS
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	800	10% Discount For BIS
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1000	10% Discount For BIS
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	10% Discount For BIS
10.7(Sulphated Ash Content)	-	700	10% Discount For BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	10000	10% Discount For BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	1500	10% Discount For BIS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	10000	10% Discount For BIS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	1500	10% Discount For BIS
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	11500	10% Discount For BIS
11.2(Resistance to External Blows at 0°C)	-	1200	10% Discount For BIS

Complete

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

16 TO 355 MM

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	100	10% discount to BIS
7.2(Length)	-	100	10% discount to BIS
7.4 table -3 & 4(6.1 Dimensions)	-	200	10% discount to BIS
7.4.1.2(Ovality)	-	100	10% discount to BIS
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	11700	10% discount to BIS
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1500	10% discount to BIS
8.2(Longitudinal Reversion Test)	-	800	10% discount to BIS
8.4( Melt Flow Rate)	-	1000	10% discount to BIS
8.5 (Oxidation Induction Time)	-	1000	10% discount to BIS
8.7(Density)	-	500	10% discount to BIS
8.8(Tensile Strength for Butt-fusion)	-	1000	10% discount to BIS
8.9 table-6(Elongation at Break)	-	1000	10% discount to BIS
8.1(Slow Crack Growth Rate)	-	4000	10% discount to BIS
8.3(Carbon black)	-	1000	10% discount to BIS
8.6(Overall migration)	-	1000	10% discount to BIS
5.2(Polyethylene Resin)	-	7000	10% discount to BIS
6, 6.1(PIPE DESCRIPTION)	-	0	10% discount to BIS
5, 5.1 table-1(MATERIALS)	-	0	-
5.3 (a)(Carbon Black Master Batch)	-	1000	10% discount to BIS
5.3(b)(Carbon Black Master Batch)	-	1000	10% discount to BIS
5.3(c)(Carbon Black Master Batch)	-	1000	10% discount to BIS
5.3(d)(Carbon Black Master Batch)	-	3000	10% discount to BIS
5.4(Anti oxydent)	-	1000	10% discount to BIS
6.2.1(6.1.1 Identification Stripes)	-	200	10% discount to BIS

Complete

-
-

Bureau of Indian Standards

The National Standards Body of India

Delhi Analytical Research Laboratory

PLOT NO-2, TIMBER BLOCK, JHILMIL INDUSTRIAL AREA NEAR DILSHAD GARDEN METRO STATION, NEW Delhi, East, Delhi, 110095

9717324010 [email protected]

Scope List