BIS - LIMS (Laboratory Information Management System)

Bharat Test House Pvt. Ltd.

1668 (DIV-II), HSIIDC INDUSTRIAL ESTATE, RAI, DIST. SONEPAT, HARYANA, INDIA, Sonipat, Sonipat, Haryana, 131029

9310314585 [email protected]

Scope List

Reset

25 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 5382 (2018)

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials (Second Revision)

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Dimensions (Type 2 C Drums Figure 2))	-	1111	new
4.2.2(Imperfections and defects)	-	400	-
4.2.2(Surface imperfections)	-	400	-
4.2.2(i)In zones involved in sealing function)	-	400	-
4.2.2(ii) In zones not involved in sealing function)	-	400	-
4.2.2(Internal Imperfections)	-	400	-
4.2.3(Hardness, IRHD from buttons )	-	900	-
4.2.4(Tensile strength, MPa)	-	1500	-
4.2.5(Compression set in air)	-	2000	-
4.2.5.2(Compression set at 23 ºC for 72 h)	-	2000	-
4.2.5.2(Compression set at 70 ºC for 24 h)	-	2000	-
4.2.5.3(Low temp compression set at -10 ºC for 72 h)	-	2000	-
4.2.6(Ageing 7 days at 70 ºC)	-	3000	-
4.2.6(Hardness, IRHD from buttons Tensile strength, % Elongation at break , % )	-	900	-
4.2.7(Stress relaxation, max)	-	5000	-
4.2.8(Volume change in water , max/min 7 days at 70 ºC )	-	700	-
4.2.9(Ozone resistance)	-	2000	-
4.2.10(Spliced joint)	-	500	-

Complete

26 Jul, 2024

-
-

IS 14625 (2015)

Plastics Feeding Bottles ( First Revision )

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Chem)(Physical Requirements)	-	500	-
Cl 5.1.3(Chem)(Wall Thickness)	-	900	-
Cl 5.1.4(Chem)(Capacity)	-	1100	-
Cl 5.3.2(Chem)(Transparecy)	-	1500	-
Cl 5.3.3(Chem)(Leakage Test)	-	900	-
Cl 5.3.4(Chem)(Drop Test)	-	900	-
Cl 5.3.5(Chem)(Ageing Resistance)	-	2000	-
Cl 5.3.6(Chem)(Compressive Deformation Resistance)	-	1200	-
Cl 5.3.7(Chem)(Product Resistance of Printed Containers)	-	1000	-
Cl 5.1(Chem)(Physical Requirements)	-	500	-
Cl 5.3.7(Chem)(Product Resistance of Printed Containers)	-	1000	-

Complete

26 Jul, 2024

-
-

IS 21 (1992)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2, Table 1of IS:21 (Designation 19000)(Silicon)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Iron)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Copper)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Zinc)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Manganese)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Magnesium)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Aluminium)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	5500	-
4.2, Table 1of IS:21 (Designation 64430)(Lead)	-	5500	-
4.2, Table 1of IS:21 (Designation 19000)(Lead)	-	5500	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(0.2 Percent Proof Stress)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(0.2 Percent Proof Stress)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(0.2 Percent Proof Stress)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(0.2 Percent Proof Stress)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(0.2 Percent Proof Stress)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Tensile Strength)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Titanium and or other grain refining elements)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Aluminium)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Tensile Strength)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Cu+Si+Fe+Mn+Zn)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	1500	-
4.2, Table 1of IS:21 (Designation 51000-B)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Manganese)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Bend Test (Radius of Bend))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Bend Test (Radius of Bend))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Bend Test (Radius of Bend))	-	1500	-
4.2, Table 1of IS:21 (Designation 51000-B)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Iron)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Bend Test (Radius of Bend))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Bend Test (Radius of Bend))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Bend Test (Radius of Bend))	-	1500	-
4.2, Table 1of IS:21 (Designation 51000-B)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Magnesium)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Tensile Strength)	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	1500	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Bend Test (Radius of Bend))	-	1500	-
4.2, Table 1of IS:21 (Designation 64430)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Cu+Si+Fe+Mn+Zn)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Titanium and or other grain refining elements)	-	0	-

Complete

26 Jul, 2024

-
-

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	3000	-
7.0(CARBON)	-	3000	-
7.0(MANGANESE)	-	3000	-
7.0(SULPHUR)	-	3000	-
7.0(PHOSPHORUS)	-	3000	-
7.0(NITROGEN)	-	3000	-
7.0(MICRO ALLOYS)	-	3000	-
7.0(SILICON)	-	3000	-
8(Mechanical and Physical Properties)	-	1800	-
Cl 8(UTM)	-	1800	-
Cl 9(Workmanship)	-	0	-
Cl 9.5(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	500	-

Complete

26 Jul, 2024

-
-

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

12500 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others: Rs.12,500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Outer Diameter, Thickness & Mass)	-	500	-
Cl 7(Workmanship)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1500	-
Cl 13(Workmanship)	-	0	-
8 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	1500	-
8 AND AS PER IS 4736(MASS OF ZINC COATING)	-	1500	-
5 AND AS PER IS 10748(COPPER)	-	5000	-
5 AND AS PER IS 10748(CARBON EQUIVALENT)	-	5000	-
5 AND AS PER IS 10748(CARBON)	-	5000	-
Clause - 5.1, Table-3(SILICON)	-	5000	-
Clause - 5.1, Table-3(MANGANESE)	-	5000	-
Clause - 5.1, Table-3(NITROGEN)	-	5000	-
Clause - 5.1, Table-3(PHOSPHURS)	-	5000	-
Clause - 5.1, Table-3(SULPHUR)	-	5000	-
Clause - 5.1, Table-3( CARBON)	-	5000	-
5 AND AS PER IS 10748(MICRO ALLOY)	-	5000	-

Complete

26 Jul, 2024

-
-

IS 740 (1977)

Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (Second Revision)

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1of IS:740 (Designation & Condition 65032, 'W')(Tensile Strength of Size upto and including 25 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation & Condition 64430, 'W')(Tensile Strength of Size upto and including 25 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation & Condition 24345, 'W')(Tensile Strength of Size upto and including 12 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation & Condition 19000, '112')(Tensile Strength of Size upto and including 12 mm)	-	1500	-
4.1, Table 1of IS:740 (Designation 65032)(Aluminium)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Either Cr or Mn shall present)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Chromium)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Titanium and or other grain refining elements)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Zinc)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Manganese)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Iron)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Silicon)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Magnesium)	-	4000	-
4.1, Table 1of IS:740 (Designation 65032)(Copper)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Aluminium)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Cr+Mn)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Chromium)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Titanium and or other grain refining elements)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Zinc)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Manganese)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Iron)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Silicon)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Magnesium)	-	4000	-
4.1, Table 1of IS:740 (Designation 64430)(Copper)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Aluminium)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Cr+Mn)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Chromium)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Titanium and or other grain refining elements)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Zinc)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Manganese)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Iron)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Silicon)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Magnesium)	-	4000	-
4.1, Table 1of IS:740 (Designation 55000)(Copper)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Aluminium)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Cr+Mn)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Chromium)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Titanium and or other grain refining elements)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Manganese)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Iron)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Silicon)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Magnesium)	-	4000	-
4.1, Table 1of IS:740 (Designation 53000)(Copper)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Aluminium)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Chromium)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Titanium and or other grain refining elements)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Zinc)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Manganese)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Iron)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Silicon)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Magnesium)	-	4000	-
4.1, Table 1of IS:740 (Designation 24345)(Copper)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Aluminium)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Zinc)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Manganese)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Iron)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Silicon)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Magnesium)	-	4000	-
4.1, Table 1of IS:740 (Designation 19000)(Copper)	-	4000	-

Complete

26 Jul, 2024

-
-

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Others-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl. 7.1 & 7.2 Table 1(Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5500	-
Cl.12(Corrosion Resistance- IS 10461(Part1))	-	1000	-
Cl.12(Corrosion Resistance- IS 10461(Part2))	-	1000	-
6(Freedom from defects , IS 6911)	-	500	-
10.1,Table 4&Table 6(Tensile Test - IS 1608(Pt -1))	-	1500	-
10.2,Table 4&Table 5(Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-	1500	-
10.3(Bend Test - IS 1599)	-	1500	-
11,Table 7(Erichsen cupping test-IS 10175)	-	800	-
15(Surface Finish)	-	0	-
17(Dimension and tolerance)	-	200	-

Complete

26 Jul, 2024

-
-

IS 15558 (2005)

Mini domestic water heater for use with LPG - Specification

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Construction)	-	500	-
4.1.2(Construction)	-	500	-
4.1.3(Construction)	-	500	-
4.1.4(Construction)	-	500	-
4.1.5(Construction)	-	500	-
4.1.6(Construction)	-	500	-
4.1.7(Construction)	-	500	-
4.1.8(Construction)	-	500	-
4.1.9(Construction)	-	500	-
4.1.10(Construction)	-	500	-
4.1.11(Construction)	-	500	-
4.1.12(Construction)	-	500	-
5.1(Materials)	-	1000	-
5.2(Materials)	-	1000	-
5.3(Materials)	-	1000	-
5.4(Materials)	-	1000	-
5.5(Materials)	-	1000	-
6.1(Connections)	-	200	-
6.2(Connections)	-	200	-
6.3(Connections)	-	200	-
6.4(Connections)	-	200	-
6.5(Connections)	-	200	-
6.6(Gas Inlet Connections)	-	200	-
6.6(Gas Inlet Connections)	-	200	-
6.6(Gas Inlet Connections)	-	200	-
7(Flame Visibility)	-	200	-
8(Gas Taps)	-	200	-
9(Flame Failure Device)	-	200	-
10(Ignition Device)	-	200	-
11(Protection Against Accidental Overheating)	-	800	-
12(Water Rate Adjuster)	-	200	-
14(Gas Soundness)	-	1000	-
15(Water Soundness)	-	1500	-
16(Thermal Efficiency)	-	1500	-
17(Combustion)	-	1000	-
18(Gas Consumption)	-	1000	-
19.1(Ignition and flame travel)	-	200	-
19.2(Ignition and flame travel)	-	200	-
19.3(Ignition and flame travel)	-	200	-
20(Flame Stability)	-	800	-
21(Noise Control)	-	200	-
22(Flash Back)	-	800	-
23(Resistance to Draught)	-	1000	-
24(Fire Hazard And Limiting Temperature)	-	800	-
25(Time For Temperature Rise)	-	1200	-
26(Hot Water Output Test)	-	500	-
27(Marking)	-	200	-

Complete

26 Jul, 2024

-
-

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0 (chem)(MATERIAL)	-	1000	-
4.6.2(TRANSPARANCY)	-	500	-
4.6.3(LEAKAGE TEST)	-	700	-
4.6.4(DROP TEST)	-	500	-
4.6.5(MIGRATION TEST)	-	2500	-
4.6.6(PORTABILITY TEST)	-	2000	-
4.6.6 (chem)(Water Potability test (after 30 days) (a) Taste (b) Odour)	-	2000	-
4.6.5.1 (chem)(Colour migration (Caps))	-	2500	-
4.6.5.1 (chem)(Colour migration (Container))	-	2500	-
4.6.5 , IS:9845:1998 (chem)(Migration of Caps - a. Amount of extractive)	-	2500	-
4.6.5 , IS:9845:1998 (chem)(Migration- b. Amount of extractive)	-	2500	-
4.6.4, clause 8 of IS:2798:1998(Drop test )	-	500	-
4.6.3, clause 6 of IS:2798:1998(Leakage test- c. Air pressure leakage)	-	700	-
4.6.3, clause 6 of IS:2798:1998(Leakage test- b. Vibration leakage)	-	700	-
4.6.3, clause 6 of IS:2798:1998(Leakage test- a. Closure leakage )	-	700	-
4.6.2.1, Annex A(Transparency (Blue tint in polycarbonate & PET containers of 5 litre and above capacity))	-	500	-
4.6.2 Annex A(Transparency)	-	500	-
4.5, IS:2798:1998(Wall thickness- Bottom, in mm)	-	500	-
4.5, IS:2798:1998(Wall thickness- Middle , in mm)	-	500	-
4.5, IS:2798:1998(Wall thickness- Top , in mm )	-	500	-
Cl. 4.4 (a)(Capacity)	-	500	-
4.3(Workmanship, Finish & Appearance)	-	0	-
4.2(Design, Shape & Dimension )	-	500	-
4.1(Material )	-	1000	-

Complete

26 Jul, 2024

-
-

IS 15609 (2005)

Polyethylene flexible pouches for the packing of natural mineral water and packaged drinking water - Specification

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Material)	-	500	-
6.1.1(Description)	-	500	-
6.1.2(Film Form)	-	300	-
6.1.3(Winding of the Film )	-	300	-
6.1.4(Odour)	-	300	-
6.1.5 A-2 of IS: 2508:2016(Thickness)	-	300	-
6.1.6(Width)	-	300	-
6.1.7 IS: 9845:1998(Migration- a. Amount of extractive )	-	1500	-
6.1.7 IS: 9845:1998(Migration- b. Colour migration)	-	1500	-
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength a. Lengthwise direction)	-	600	-
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength b. Crosswise direction)	-	600	-
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - a. Lengthwise direction)	-	600	-
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - b. Crosswise direction)	-	600	-
6.1.10 Annex -6 of IS:2508:2016(Dart impact Resistance)	-	1100	-
7.2 Annex F(Stack Load test)	-	500	-
7.4 Annex H(Ink adhesion test for printed pouches)	-	500	-
7.1 Annex E(Water Potability test (after 30 Days) a) Taste b) Odour)	-	600	-
7.3 Annex G(Drop test )	-	300	-
7.5 Annex J(Product resistance test for printed pouches)	-	300	-

Complete

26 Jul, 2024

-
-

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	-
4.1(Raw Material)	-	500	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	-
4.2(Tapes – Linear Density )	-	500	-
4.3.1(The two rows of stitches shall be separated from each other)	-	500	-
4.3.1( The outer stitch)	-	500	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	500	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	500	-
4.3.1(stitches/dm)	-	500	-
4.3.2(Mouth)	-	500	-
4.4(Liner IS 10146 or IS 10910.)	-	500	-
4.4(Mass of the loose liner )	-	500	-
4.4(Width of the loose liner)	-	500	-
4.4(Length of the line)	-	500	-
4.4(Bottom seam of the loose liner)	-	500	-
4.4.1(Liner)	-	500	-
4.5 and Table 1 i(Capacity)	-	1000	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	1200	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	1200	-
5.2 and Table 1 iii(Ends per dm )	-	1100	-
5.2 and Table 1 iv(Picks per dm )	-	1100	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	1200	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	1200	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	2500	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	2500	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	2400	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	2400	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	2400	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	5000	-
5.2 and Table 1 x(Ash content )	-	2000	-

Complete

26 Jul, 2024

-
-

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	500	-
3.2(Tapes – Width )	-	500	-
3.2(Tapes – Linear Density )	-	500	-

Complete

26 Jul, 2024

-
-

IS 14625 (2015)

Plastics Feeding Bottles ( First Revision )

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1.3(Wall Thickness)	-	500	-
Cl 5.1.4(Capacity)	-	1100	-
Cl 5.3.2(Transparecy)	-	1500	-
Cl 5.3.3(Leakage Test)	-	900	-
Cl 5.3.4(Drop Test)	-	900	-
Cl 5.3.5(Ageing Resistance)	-	2000	-
Cl 5.3.6(Compressive Deformation Resistance)	-	1200	-
Cl 5.3.7(Product Resistance of Printed Containers)	-	1000	-
Cl 5.1(Physical Requirements)	-	500	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Antimony)	-	3000	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Arsenic)	-	3000	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Chromium)	-	3000	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Mercury)	-	3000	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Cadmium)	-	3000	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Lead)	-	3000	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Barium)	-	3000	-
Sl. No. i), Table 1, Cl.5.2.1.7(Migration of certain elements - Selenium)	-	3000	-
Cl 5.1.4.2 (a)(Test for permanency of Pigment)	-	1000	-
5.3.8 a)(Migration Test a) Distilled water at 40±2° hrs)	-	2500	-
5.3.8 b)(Migration Test b) n-Haptane at 38±1° C for 30 min)	-	2500	-

Complete

26 Jul, 2024

-
-

IS 13395 (1995)

Performance of handles and handle assemblies attached to cookware - Specification

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Bending Strength)	-	600	-
5.3(Torque Strength)	-	1000	-
5.4(Impact Strength)	-	1000	-
5.5(Fatigue Resistance)	-	1000	-
5.6(Leakage)	-	500	-
5.7(Thermal Insulation)	-	1200	-
5.8(Heat Resistance)	-	1000	-
5.9(Washing Resistance)	-	1000	-
5.1(Burning Resistance)	-	1200	-
5.1(General)	-	0	-

Complete

26 Jul, 2024

-
-

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.2(Material)	-	450	-
Clause 4.2.1(Lining)	-	450	-
Clause 4.2.2 (a)(Reinforcement)	-	500	-
Clause 4.2.2 (b)(Reinforcement)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1200	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	1200	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1500	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1500	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	500	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	300	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	-
Clause 5.2.1(BIS Certification Marking )	-	0	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	500	-
Clause 4.1(General)	-	500	-
Clause 4.2.3(Cover)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	1200	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	1200	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	500	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	500	-
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	500	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	500	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	500	-
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	500	-
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	500	-
9.1(PIPE ENDS)	-	500	-

Complete

26 Jul, 2024

-
-

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 (General)	-	500	-
Clause 4.2(Material)	-	450	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1500	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1500	-
Clause 4.2.1(Lining)	-	450	-
Clause 4.2.2(Reinforcement)	-	500	-
Clause 4.2.3(Cover)	-	500	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	500	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	300	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	-
Clause 5.2.1(BIS Certification Marking )	-	0	-

Complete

26 Jul, 2024

-
-

IS 7466 (1994)

Rubber gaskets for pressure cookers - Specifications (First Revison)

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Workmanship and Finish )	-	500	-
3.4-Table 1(i)(Requirements of Rubber Used for Gaskets-Hardness IRHD)	-	1200	-
3.4-Table 1(ii)(Requirements of Rubber Used for Gaskets-Tensile strength,)	-	1200	-
3.4-Table 1(iii)(Requirements of Rubber Used for Gaskets-Elongation at break)	-	1200	-
3.4-Table 1(iv-a)(Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing 3 days in Aie-oven Change From Original Value))	-	3500	-
3.4-Table 1(iv-b)(Requirements of Rubber Used for Gaskets-Tensile strength(After ageing 3 days in Aie-oven Change From Original Value))	-	3500	-
3.4-Table 1(iv-c)(Requirements of Rubber Used for Gaskets-Elongation at break(After ageing 3 days in Aie-oven Change From Original Value))	-	3500	-
3.4-Table 1(v-a)(Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing in an autoclave Change From Original Value))	-	3500	-
3.4-Table 1(v-b)(Requirements of Rubber Used for Gaskets-Tensile strength(After ageing in an autoclave Change From Original Value))	-	3500	-
3.4-Table 1(v-c)(Requirements of Rubber Used for Gaskets-Elongation at break(After ageing in an autoclave Change From Original Value))	-	3500	-
3.4-Table 1(vi)(Compression set)	-	1500	-
3.5-ANNEX C(PERFORMANCE TEST FOR PRESSURE COOKER )	-	500	-
Clause 4.3 Table 1(Zinc oxide)	-	1200	-
Clause 3.4 Table 1(Heavy metal content)	-	1200	-
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	3500	-
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	3500	-
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	3500	-

Complete

26 Jul, 2024

-
-

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	500	-
Cl. 14.1(Weight on lots of 10 tonnes min)	-	500	-
Cl. 14.1(Weight on individual length)	-	500	-
Cl. 14.1(Random Length)	-	500	-
Cl. 14.1(Exact Length)	-	500	-
Cl. 15.2, Table 3(Elongation- IS 1608)	-	1500	-
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	1500	-
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	1500	-
Cl. 10.7, Fig 5(Total twist, V)	-	1000	-
Cl. 10.6, Fig 4(External Corner Radius)	-	1000	-
Cl. 10.5, Fig 3(Squareness of side)	-	500	-
Cl. 10.4, Fig 2(Convexity, X2)	-	1000	-
Cl. 10.4, Fig 2(Concavity, X1)	-	1000	-
Cl. 10.2, Fig 1(Outside dimension (T))	-	500	-
Cl. 10.2, Fig 1(Outside dimension (H))	-	500	-
Cl. 10.2, Fig 1(Outside dimension (B))	-	500	-
Cl. 10.1, 14.1, 18.1(Straightness)	-	1000	-
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	6000	-
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	6000	-
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	6000	-
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	6000	-
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	6000	-
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	6000	-
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	6000	-

Complete

26 Jul, 2024

-
-

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(General)	-	200	-
4.1 of IS 5116(General)	-	-	-
4.1.1(General)	-	-	-
4.2 of IS 5116(General)	-	-	-

Complete

26 Jul, 2024

-
-

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

16000 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others: Rs.14,500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Construction - Pressure Regulating Device)	-	500	-
6.2(Construction-Safety Relief Device)	-	500	-
6.3(Construction-Temperature Responsive Pressure Relief Device)	-	500	-
4.1(Capacity )	-	500	-
5.1.1(Body, Lid, Containers and Grid)	-	7000	-
6(CONSTRUCTION)	-	500	-
6.1(Pressure Regulating Device)	-	500	-
6.1.3(Pressure Regulating Device)	-	500	-
6.1.4(Pressure Regulating Device)	-	500	-
6.1.5(Pressure Regulating Device)	-	500	-
6.2(Safety Relief Device)	-	500	-
6.2.1(Safety Relief Device)	-	500	-
6.2.2(Safety Relief Device)	-	500	-
6.3.1(Temperature Responsive Pressure Relief Device)	-	500	-
6.3.1(Temperature Responsive Pressure Relief Device)	-	500	-
6.4.1(Handles and Knobs)	-	500	-
6.4.1.1(Handles and Knobs)	-	500	-
7.1(WORKMANSHIP AND FINISH)	-	500	-
7.2(WORKMANSHIP AND FINISH)	-	500	-
7.3(WORKMANSHIP AND FINISH)	-	500	-
7.4(WORKMANSHIP AND FINISH)	-	500	-
8.1(Air Pressure Test)	-	2500	-
8.2(Proof Pressure Test)	-	2500	-
8.3(Operating Test for Pressure Regulating Device)	-	2500	-
8.4(Test for Safety Pressure Relief Device)	-	2000	-
8.5(Bursting Pressure Test)	-	2000	-
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	1500	-
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	1500	-
8.7(Test for Spring Loaded Mechanism)	-	1500	-
8.8(Test for Spring Loaded Mechanism)	-	1500	-
8.9(Test for Spring Loaded Mechanism)	-	1500	-

Complete

26 Jul, 2024

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	5000	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	5000	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	5000	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	5000	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	2000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1500	-

Complete

26 Jul, 2024

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Carbon %)	-	3000	-
4.1(Manganese %)	-	3000	-
4.1(Phosphorus %)	-	3000	-
4.1(Sulphur %)	-	3000	-
4.1(Silicon %)	-	3000	-
4.1( Copper %)	-	3000	-
4.1(Cr)	-	3000	-
4.1(Mo)	-	3000	-
4.1(Ni)	-	3000	-
4.1( Nitrogen%)	-	3000	-
4.1(CE)	-	3000	-
4.1(Sulphur and phosphorous)	-	3000	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228)	-	3000	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228)	-	3000	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228)	-	3000	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	3000	-
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	3000	-
Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3000	-
Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3000	-
Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3000	-
Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3000	-
Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3000	-
Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	3000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	3000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	3000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	3000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	3000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	3000	-
Cl 5(Deformations and Surface Characteristics)	-	500	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	500	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	1000	-
Cl 6.1(Length, Width & Thickness)	-	500	-
Cl 7.2(Weight)	-	500	-
Cl 8.1(UTM)	-	4000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	4000	-
Cl. 8.1 Table 3(TS/YS ratio)	-	4000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	4000	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	4000	-
Cl 9.3(Load In One Direction)	-	3000	-
Cl. 9.3, Table 4(Bend Test )	-	2500	-
Cl 9.4(Load In Other Direction From Bend)	-	3000	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	3000	-

Complete

26 Jul, 2024

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	-
4.1(Raw Material)	-	1000	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3.1( The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(The number of stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4 and Table 1 i(Capacity)	-	1500	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	1700	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	1700	-
5.2 and Table 1 iii(Ends per dm )	-	1100	-
5.2 and Table 1 iv(Picks per dm )	-	1100	-
5.1 and Table 1 v(Mass of sack )	-	1200	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	2500	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	2500	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1200	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	1200	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	1200	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	5000	-
5.2 and Table 1 x(Ash content )	-	2000	-

Complete

26 Jul, 2024

-
-

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

15200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Outer Diameter, Thickness & Mass)	-	600	-
Cl 10.1(Manufacturing )	-	0	-
Cl 10.1.1(Manufacturing )	-	0	-
Cl 12(Workmanship)	-	0	-
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	2800	-
Cl 15(Workmanship)	-	0	-

Complete

26 Jul, 2024

-
-

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification - IS 444)	-	0	-
5(Lining - IS 444)	-	0	-
5(Reinforcement - IS 444)	-	0	-
5(Cover - IS 444)	-	0	-
5(Lining and Cover - IS 444)	-	0	-
6.1- Table 1(Internal diameters - ISO 4671)	-	2100	-
6.2(Concentricity - ISO 4671)	-	2100	-
6.3(Length -IS 4671)	-	2100	-
6.4( thickness of the lining plus cover - ISO 4671)	-	2100	-
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	2100	-
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	900	-
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	900	-
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	500	-
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	500	-
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	1200	-
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	1200	-
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	1200	-
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	300	-
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	300	-
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	500	-
7.2 - Table 3(Adhesion between components - ISO 8033)	-	500	-
7.2 - Table 3(Ozone resistance - ISO 7326)	-	2000	-
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	1000	-
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	1000	-

Complete

26 Jul, 2024

-
-

Bureau of Indian Standards

The National Standards Body of India

Bharat Test House Pvt. Ltd.

1668 (DIV-II), HSIIDC INDUSTRIAL ESTATE, RAI, DIST. SONEPAT, HARYANA, INDIA, Sonipat, Sonipat, Haryana, 131029

9310314585 [email protected]

Scope List