BIS - LIMS (Laboratory Information Management System)

GUJARAT TEST HOUSE

Plot No.292, Road No.4, G.I.D.C., Kathwada, Ahmedabad-382 430., Ahmedabad, Ahmadabad, Gujarat, 382430

9825063601 [email protected]

Scope List

Reset

4 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 15633 (2005)

Automotive vehicles - Pneumatic tyres for passenger car vehicles - Diagonal and radial ply - Specification

Diagonal & Radial Ply

76000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1.1.1- Refer Annex B Col 2 and Annex D(test method )(Tyre dimensions/Section width)	-	800	Dimensions (Cl. 4.1)-800
4/4.1.1.2- Refer Annex B Col 2 and Annex D(test method )(Tyre outer diameter)	-	800	Dimensions (Cl. 4.1)-800
4/4.2.1 /4.2.2/4.2.3,Refer Annex D ,Table 13(Load/Speed Performance Test)	-	800	Load/Speed Performance Test (Cl. 4.2)-800

Complete

15 Jul, 2021

-
-

IS 14561 (2014)

Fire resisting (Insulating) filing cabinets - Specification (Second Revision)

Vertical/ Lateral

205000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(i) Height)	-	500	IS 14561 CL 4.1
4.1(ii) Width)	-	500	IS 14561
4.1(iii) Depth)	-	500	IS 14561
4.1(iv) Height of the bottom drawer above floor level)	-	200	IS 14561
6(Designations: The filing cabinet shall be designated by the commonly used name, type, the fire rating and the number of this Indian Standard.)	-	200	IS 14561
7.1(Outer body and Inner Box: Outer body and inner box shall be fabricated from mild steel or galvanized steel sheets of not less than 0.8 mm and not more than 1.2 mm nominal thickness. The steel shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	100	IS 14561
7.2(Cabinets Sub-Assembly: The external body and drawer fronts of the fire resisting (insulating) filing cabinet shall be of double wall type with homogeneous insulating material filled in between. Further the construction of the cabinet shall be such that each drawer slides in an individual inner box. The inner boxes shall have a insulating layer between each other to prevent fire spreading from one drawer to another. The joining of inner box, intermediate piece and outer body shall be such that, it forms a cavity to receive drawer front )	-	100	IS 14561
7.3(Filing Drawer: The drawer shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall have an arrangement on the sides suitable for the drawer suspension system and an arrangement to stop it when fully pushed in.)	-	100	IS 14561
7.3.1(Drawer Front: The drawer front shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall be firmly secured to the drawer body by welding, screwing or riveting or any combination of these processes. The construction of drawer front shall be such that it snugly fits in the cavity provided for the same )	-	100	IS 14561
7.4.1(Latch: Each drawer of the cabinet shall be removable but shall be fitted with a latch/positive stop to prevent inadvertent withdrawal and rebound. Such latch shall be lifted/unlocked by the pull of the handle or any other mechanism.)	-	100	IS 14561
7.4.2(The locking mechanism shall be designed in such a manner so that there is minimum passage for direct conduction of heat from outside to inside)	-	100	IS 14561
7.5(Drawer Suspension The drawer suspension shall be either of the following types to ensure withdrawal of the full depth of the drawer: a) Ball bearing / Roller bearing suspension (Movement), b) Solid roller suspension, and c) Telescopic slide suspension (Extension)	-	100	IS 14561
7.6(Handles: Each drawer shall be provided either with a handle made from ferrous/non-ferrous material suitably coated for corrosion resistance, or any polymer and fixed to the front of the drawer or with a built in pulling mechanism)	-	100	IS 14561
7.6.1(The drawer handle shall be strong enough to take a minimum pull of 50 N for 2 min. There shall be no sharp corners or edges to avoid injury and damage to clothing)	-	2000	IS 14561
7.7.1(Locks: Top drawer shall be provided with single or dual control key lock having not less than 6 levers or pin cylinder lock having not less than 6 pins, with duplicate keys of stainless steel/nonferrous alloy. Alternatively if required by the purchaser a 3 wheel combination lock or electronic combination lock may be provided either in place of key lock or in addition to key lock)	-	100	IS 14561
7.7.2(Each drawer may also be provided with individual key lock or pin cylinder lock or combination lock subject to agreement between the purchaser and the supplier.)	-	100	IS 14561
7.8(Locking Mechanism )	-	100	IS 14561
7.8.1(The locking mechanism shall be such that when the top drawer is pushed-in fully, it actuates locking mechanism to lock all other drawers imultaneously, when they are in pushed-in position)	-	100	IS 14561
7.8.1.1(At the time of locking the cabinet, if one of the drawers is not fully pushed-in, that drawer shall remain unlocked and can be used. As soon as that drawer is pushed-in fully, it shall get locked automatically without further operation of key by the user.)	-	100	IS 14561
7.8.1.2(In addition to the above, isolation mechanism shall also be provided to permit independent locking/ use of other drawers. Such isolation mechanism provided on drawers shall be manually operated)	-	100	IS 14561
8(Assemblies)	-	100	IS 14561
8.1(The components shall be assembled by bolting, welding, riveting or by any combination of these processes)	-	100	IS 14561
8.2(All joints between outer body and inner boxes, the drawer front and the outer body shall be such that, there is minimum direct conduction of heat from outer body to inner body)	-	100	IS 14561
9.1(Drawer Suspension Test and Latch Test: The drawer loaded with evenly distributed load of 30 kg (excluding the weight of drawer) in any drawer shall be operated for 5 000 cycles at a rate of 300 cycles/h ±10 percent. One opening and one closing shall constitute one cycle. The test shall be carried out with maximum two breaks by using electrically or mechanically operated test equipment with a counter fitted on it. After 5 000 cycles the suspension slide and latch mechanism shall not show any apparent distortion, cracks, or failures to operate in a normal smooth manner)	-	10500	IS 14561
10.1(Finish: All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale)	-	100	IS 14561
10.2(The inside and outside surfaces of the fire resisting (Insulating) filing cabinet shall be painted or powder coated. In case of paint, an appropriate primer and undercoating shall be used in accordance to industry practices. The minimum overall thickness of the coatings shall be 50 μ for powder coating and 70 μ for liquid paint. Cross hatch test shall be conducted to confirm the adhesion of coating in accordance with 10.2.1)	-	200	IS 14561
10.2.1(Cross Hatch Test)	-	300	IS 14561
11.1(Fire endurance test)	-	2500	IS 14561
11.2(Fire and impact test)	-	2500	IS 14561
12.1(Marking of Cabinets:A metal plate showing classification of cabinet together with the manufacturer’s name, serial number and the year of manufacture shall be fixed inside surface of the top drawer of the cabinet in such a way that it is visible when it is opened.)	-	100	IS 14561
12.2(Marking on Keys: The keys shall bear an identification number which shall not be the same as the serial number of the cabinet)	-	100	IS 14561

Complete

15 Jul, 2021

-
-

IS 8887 (2018)

Bitumen emulsion for roads (Cationic Type) - Specification (Third Revision)

RS1,RS2,MS,SS1,SS2

15400 View breakup
-

Complete

15 Jul, 2021

-
-

IS 303 (1989)

Plywood for General Purposes -

BWR/MR, AA/AB/BB

3050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions & Tolerances - Squareness - Annexure C)	-	20	Squareness
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	100	Quality requirement
5.1(Type - For AA Type)	-	40	AA
5.1(Type - For BB Type)	-	30	BB
5.1(Type - For AB Type)	-	30	AB
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	20	Thickness
8(Dimensions & Tolerances - Length - Cl. 8)	-	20	Length
8(Dimensions & Tolerances - Width - Cl. 8)	-	20	Width
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	20	Edge Straightness
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	50	Workmanship
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	50	Workmanship
11.3(Moisture Content - Part 1 of IS 1734)	-	150	Moisture contnent
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	250	MR
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	250	BWR
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	1000	Mycological
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	125	MOR -Along-Avg.
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	125	MOR-Along-Min.
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	125	MOR-Across-Avg
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	125	MOR-Across-Min
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	125	MOE-Along-Avg
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	125	MOE-Along-Min
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	125	MOE-Across-Avg.
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	125	MOE-Across-Min

Complete

15 Jul, 2021

-
-

Bureau of Indian Standards

The National Standards Body of India

GUJARAT TEST HOUSE

Plot No.292, Road No.4, G.I.D.C., Kathwada, Ahmedabad-382 430., Ahmedabad, Ahmadabad, Gujarat, 382430

9825063601 [email protected]

Scope List