BIS - LIMS (Laboratory Information Management System)

CIPET Amritsar

P.O. Rayon & Silk Mills, Amritsar, Amritsar, Punjab, 143105

1832258938 [email protected]

Scope List

Reset

42 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

Woven Sacks For Packaging 10Kg, 15Kg, 20Kg, 25Kg 30Kg

20780 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	-
4.2(Tapes – Linear Density )	-	500	-
4.3(Sacks)	-	300	-
4.3.1(Bottom Seam)	-	250	-
4.3.1(The number of stitches/dm)	-	250	-
4.3.2(Mouth)	-	250	-
4.4 and Table 1 i(Capacity)	-	250	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
5.1 and Table 1 v(Mass of sack )	-	300	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	Average breaking strength and elongation at break Lengthwise-Rs.1100 Widthwise-Rs.1100 UV Resistance Exposure (192hrs)-Rs.10180
5.2 and Table 1 x(Ash content )	-	950	-

Complete

06 Jan, 2024

-
-

IS 14500 (1998)

Linearlow - Densitypolyethylene (Lldpe)Films - Specification

LLDPE Film

9650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Appearance)	-	300	-
6.1.4(Density)	-	500	-
6.2.1(Nominal Thickness and Nominal Width)	-	250	-
6.2.2(Tolerance on Thickness)	-	250	-
6.2.3(Tolerance on Width)	-	250	-
6.3(Yield Tolerance)	-	600	-
6.4.1(Impact Strength (Falling Dart))	-	1000	-
6.4.2(Haze)	-	700	-
6.4.3(Slip)	-	850	-
6.4.4(Tensile strength at break)	-	1350	Tensile strength at break-1100 + 250 Specimen
6.4.5(Elongation at break)	-	1100	-

Complete

06 Jan, 2024

-
-

IS 12650 (2018)

Textiles – Jute bags for packing 50 kg foodgrains – Specification (third revision)

Jute Bags For Packing 50 Kg Foodgrains

7600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-4.1(MANUFACTURE)	-	2500	i) Dimensions- Rs. 500 ii) Ends per dm- Rs. 250 iii) Picks per dm- Rs. 250 iv) Corrected Mass per Bag- Rs.500 v) Seem (Stitch per dm)- Rs.500 vi) Safety Stitch (per dm)- Rs. 250 vii) Hemming at the mouth-Rs. 250
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): a ) Warpway- 1570 (160) for both type A & Type B)	-	1100	-
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): b ) Weftway- 1420 (145) for both type A & Type B)	-	1100	-
5-5.1-Table 1-Sr. No.vi)(SPECIFIC REQUIREMENTS-Cl. 8.7 of IS 9113 Average side seam strength (5 cm ×20 cm raveled strip), Min, N (kgf): 490 (50) for both type A & Type B)	-	1100	-
5-5.1-Table 1-Sr. No.vii)(SPECIFIC REQUIREMENTS-Cl. 8.2 of IS 9113 Moisture regain, percent, Max (see Note 3) 22 for both type A & Type B)	-	700	-
5-5.1-Table 1-Sr. No.viii)(SPECIFIC REQUIREMENTS-Cl. 8.8 of IS 9113 Oil content on dry de-oiled material, Max 3 for both type A & Type B)	-	1100	-

Complete

06 Jan, 2024

-
-

IS 10889 (2004)

High density polyethylene films (First Revision)

High Density Polyethylene (HDPE) Films (Black)

11925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Appearance)	-	100	-
6.1.2(Film Form)	-	100	-
6.1.3(Odour )	-	100	-
6.1.4(Density)	-	500	-
6.1.5(Melt Flow Rate)	-	1100	-
6.1.6(Black Film)	-	1625	Carbon Black Content - Rs. 925 Carbon Black Dispersion- Rs. 700
6.2.1, Table 1(Nominal Thickness)	-	250	-
6.2.2, Table 2(Nominal Width)	-	250	-
6.3, Table 3(Yield Tolerance)	-	600	-
6.4.1(Tensile Strength at Break)	-	1350	1100 + 250 (Specimen)
6.4.2(Elongation at Break)	-	1100	-
6.4.3(Impact Resistance (Falling Dart))	-	1000	-
5.2(Black Compound)	-	3850	Density - Rs. 500+625(Specimen) Melt Flow Index - Rs. 1100 Carbon Black Content - Rs. 925 Carbon Black Dispersion- Rs. 700

Complete

06 Jan, 2024

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

High Density Polyethylene Pipes for Potable Water Suppl

45375 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	250	-
6.2.1(6.1.1 Identification Stripes)	-	250	-
7.4 table -3 & 4(6.1 Dimensions)	-	750	-
7.2(Length)	-	300	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21650	(a) Acceptance Test (100hrs)/27°C - Rs. 4000 (a) Acceptance Test (48hrs)/80°C - Rs. 1500 (b) Type Test (165hrs)/80°C - Rs. 4800 (b) Type Test (1000hrs)/80°C - Rs.11000 + 250 (Specimen)
8.2(Longitudinal Reversion Test)	-	900	-
8.3(Carbon black)	-	1625	Carbon Black Content - Rs. 925 Carbon Black Dispersion- Rs. 700
8.4( Melt Flow Rate)	-	1100	-
8.5 (Oxidation Induction Time)	-	2200	-
8.6(Overall migration)	-	2000	Overall Migration Rs. 1700 + Rs. 300 (Specimen)
8.7(Density)	-	500	-
8.8(Tensile Strength for Butt-fusion)	-	1600	Tensile Strength for butt fusion Rs. 1100 + Rs. 500 (Specimen)
8.9 table-6(Elongation at Break)	-	1600	Elongation at Break Rs. 1100 + Rs. 500 (Specimen)
8.1(Slow Crack Growth Rate)	-	6000	Slow Crack Growth Rate Rs. 5500 + Rs. 500 (Specimen)
7.4.1.2(Ovality)	-	0	-
5.2(Polyethylene Resin)	-	5250	Density - Rs. 500+625(Specimen) Melt Flow Index - Rs. 1100 Carbon Black Content - Rs. 925 Carbon Black Dispersion- Rs. 700 Volatile Matter - Rs. 700 Water Content - Rs. 700

Complete

06 Jan, 2024

-
-

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

Rigid Plain Conduits of Insulating Materials up to 63MM

9700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1(Maximum and minimum outside diameter of socket)	-	1000	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	300	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	1000	-
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	1100	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	1000	-
10(Resistance to Heat -Ball presure test)	-	700	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	700	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	2800	a) Electrical Strength - Rs. 1100+300 (Specimen) b) Insulation Resistance - Rs. 1100+300 (Specimen)
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	1100	-

Complete

06 Jan, 2024

-
-

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

General Requirements Size – 20mm To 315mm and PVC Resin

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	250	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	250	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	-
Cl. 6.1(Stress Relief Test- Appendix A)	-	700	-
Cl. 6.2(Opacity- Appendix B)	-	575	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	3000	-
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	-
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	850	-

Complete

06 Jan, 2024

-
-

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

45 Degrees Elbows 20mm to 315mm

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1(General)	-	5625		i) Minimum Thickness & Dimensions - Rs. 500 ii) Opacity - Rs. 575 iii) Effect on Water - Rs. 3000 iv)Stress Relief Test - Rs. 700 v) Short Term Hydraulic Test - Rs. 850

Complete

06 Jan, 2024

-
-

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

90 Degree Elbow s- 20mm to 315mm

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 2.2.2(Dimensions)	-	5625		i) Minimum Thickness & Dimensions - Rs. 500 ii) Opacity - Rs. 575 iii) Effect on Water - Rs. 3000 iv)Stress Relief Test - Rs. 700 v) Short Term Hydraulic Test - Rs. 850

Complete

06 Jan, 2024

-
-

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

90 Degree Tees 20mm to 315mm

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1(General)	-	5624		i) Minimum Thickness & Dimensions - Rs. 500 ii) Opacity - Rs. 575 iii) Effect on Water - Rs. 3000 iv) Stress Relief Test - Rs. 700 v) Short Term Hydraulic Test - Rs. 850

Complete

06 Jan, 2024

-
-

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

45 Degree Tees – 20mm to 160mm

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1(General)	-	5625		i) Minimum Thickness & Dimensions - Rs. 500 ii) Opacity - Rs. 575 iii) Effect on Water - Rs. 3000 iv) Stress Relief Test - Rs. 700 v) Short Term Hydraulic Test - Rs. 850

Complete

06 Jan, 2024

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

Sockets

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1(General)	-	5625		i) Minimum Thickness & Dimensions - Rs. 500 ii) Opacity - Rs. 575 iii) Effect on Water - Rs. 3000 iv) Stress Relief Test - Rs. 700 v) Short Term Hydraulic Test - Rs. 850

Complete

06 Jan, 2024

-
-

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

Unions Size-20mm to 63mm

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1(General)	-	5625		i) Minimum Thickness & Dimensions - Rs. 500 ii) Opacity - Rs. 575 iii) Effect on Water - Rs. 3000 iv) Stress Relief Test - Rs. 700 v) Short Term Hydraulic Test - Rs. 850

Complete

06 Jan, 2024

-
-

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

Caps Size – 20mm to 315mm

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1(General)	-	5625		i) Minimum Thickness & Dimensions - Rs. 500 ii) Opacity - Rs. 575 iii) Effect on Water - Rs. 3000 iv) Stress Relief Test - Rs. 700 v) Short Term Hydraulic Test - Rs. 850

Complete

06 Jan, 2024

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

Upto1500 Ltrs and Above 1500ltrs

18925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	3050	Net & Gross Capacity-Rs.500 Overall Diameter-Rs. 250 Overall Height-Rs. 250 Internal dia of man – hole-Rs. 250 Wall thickness upon effective height-Rs. 250 Wall thickness above effective height-Rs. 250 Minimum weight without lid-Rs.500
6.1(Finish)	-	300	-
7.1.1(Resistance to Deformation)	-	700	-
7.2(Resistance to Impact)	-	1100	-
7.3(Test for Top Load Resistance)	-	900	-
7.4(Tensile Strength)	-	1600	Rs. 1100 + 500 (Specimen)
7.5(Flexural Modulus)	-	1600	Rs. 1100 + 500 (Specimen)
7.6(overall Migration)	-	2200	Rs. 1700 + 500 (Specimen)
9.1(Man-Hole and Hand-Hole Lids)	-	3225	Material Identification-Rs. 1050 Thickness- Rs.250 Visual appearance- Rs. 300 Carbon black content- Rs.925 Carbon black dispersion- Rs.700
9.2.1(Man-Hole and Hand-Hole Lids)	-	400	-
4.2.3(Carbon Black Content )	-	1625	Rs. 925+700
5(Types and Features )	-	2225	Rs. 500+625 (Specimen) Rs. 1100

Complete

06 Jan, 2024

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

HDPE Pipe For Sewerage 63mm to 400mm

11475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Colour)	-	300	-
6(Dimensions of pipes)	-	250	-
7(Visual Appearance)	-	300	-
8.1(Hydraulic characteristics)	-	6400	(i) Acceptance Test - 48 hrs- Rs. 1600 (ii) Type Test-165 hrs- Rs. 4800
8.2(Reversion)	-	1000	Rs. 700+300 (Specimen)
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1100	-
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	-

Complete

06 Jan, 2024

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

40mm to 200mm

19175 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	700	-
Cl.5(Dimensions of pipe - i) Outside diameter)	-	500	-
Cl.6(Visual Appearance)	-	300	-
7.1 Table -2(Hydraulic Characteristics)	-	6400	i) Quality Test for 165 hours at 80ºC - Rs. 4800 ii) Acceptance Test for 48 hours at 80ºC -Rs.1600
7.2(Reversion Test)	-	1000	Rs. 700+300 (Specimen)
7.3(Tensile Test)	-	1350	Rs. 1100+ 250 (Specimen)
7.4table-2(Fusion Compatibility Test)	-	6400	i) Quality Test for 165 hours at 80ºC - Rs. 4800 ii) Acceptance Test for 48 hours at 80ºC -Rs.1600
(Cl.7.5)(Density)	-	500	-
Cl.7.6(Melt Flow Rate)	-	1100	-

Complete

06 Jan, 2024

-
-

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

UPVC Pipe (Elastomeric Sealing ring socket)

38675 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	100	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	100	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	100	-
7.2.1(DIMENSIONS-Socket)	-	100	-
9.1(PIPE ENDS)	-	100	-
8(SEALING RINGS)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900	700 + 200 (Specimen)
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
Clause 10.7(Sulphated Ash Content)	-	950	-
11.2(Resistance to External Blows at 0°C)	-	1400	1100 + 300 (Specimen)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	-
10.1(Colour)	-	300	-
10.3(Effect on Water)	-	3000	-
6.1.2(PVC Resin)	-	4100	VCM Content -Rs.3000 K-Value- Rs. 1100

Complete

06 Jan, 2024

-
-

IS 15225 (2002)

Chlorinated polyvinyl chloride compounds used for pipes and fittings - Specifications

CPVC for Pipes and Fittings

17475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1(Resin k-value)	-	1100	-
8.1.2(Resin chlorine content)	-	4300	-
8.1.3(Form)	-	250	-
8.1.4(Compound chlorine content)	-	4300	-
8.1.5(Appearance)	-	300	-
8.2.1(Vicat softening temperature)	-	1100	-
8.2.2(Charpy impact strength)	-	1725	Charpy impact strength - Rs. 1100 + 625 Specimen
8.2.3(Tensile strength)	-	1725	Tensile strength - Rs. 1100 + 625 Specimen
8.2.4(Tensile modulus)	-	1725	Tensile modulus - Rs. 1100 + 625 Specimen
8.3(Ash content)	-	950	-

Complete

06 Jan, 2024

-
-

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

Size-110mm To 400mm

26650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1200	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	250	-
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	250	-
6.1.3 (Length of Pipe)	-	0	-
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	250	-
7(Physical characteristics )	-	2700	7.1 Visual Appearance- Rs. 300 7.2 Colour- Rs. 300 7.3 Vicat Softening Temp.- Rs. 1100 7.4 Longitudinal Reversion- Rs. 700+300 (Specimen)
8(MECHANICAL CHARACTERISTICS)	-	2800	8.1 Resistance to External Blow at 0ºC- Rs. 1100+300 (Specimen) 8.2 Ring Stiffness Test- Rs. 1100+300 (Specimen)
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	11850	i) Acceptance test (1 hr/27ºC)- Rs. 850 ii)Type test (1000 hrs /60ºC)- Rs. 11000
10(Performance requirements)	-	1850	10.1.1 Internal hydrostatic pressure test for elastomeric sealing ring joints- Rs. 850 10.1.2 Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints-Rs. 1000
'7.5 (amdt.7)(Effect on Water (Type test))	-	3000	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	250	-
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	250	-
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	0	-
6.1.4, Table 3(iv) Length of spigot, l1)	-	0	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	250	-
7.1(Appearance:- )	-	300	-
7.2(Colour )	-	300	-
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1100	-
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1000	700+300 Specimen
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1400	1100+300 Specimen
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1400	1100+300 Specimen
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	11000	-
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	850	-
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1000	-
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	850	-
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	-
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	250	-
9.2 IS 14182(b) Solvent cement)	-	250	-

Complete

06 Jan, 2024

-
-

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

CPVC for Potable Hot and Cold Water Supply

144125 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.1 Annex B(Chloride Content of Resin)	-	17200	i) Chloride Content of Resin- Rs. 1100 ii) Chloride content- Rs. 4300 iii) Verification of the Malfunction Temperature, Tmal:- Rs. 11000+300 (Specimen) iv) Density- Rs. 500
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	500	-
8(Pipe Ends)	-	300	-
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	6475	i) Visual Appearance- Rs.300 ii) Opacity- Rs. 575 iii) Effect on Water- Rs. 3000 iv) Reversion Test- Rs. 700+300 (specimen) v) Vicat Softening Temperature- Rs. 1100 vi) Density- Rs. 500
10(Mechanical Properties)	-	119650	i) Acceptance Test- Rs. 850 i) Type Test- Rs. 4800 ii) Thermal Stability by Hydrostatic Pressure Testing - Rs. 1000+109500 iii) Resistance to External Blow at 0°C Rs. 1100 + 300 iv) Flatterning Test- Rs. 500 v) Tensile Strength- Rs. 1100+500

Complete

06 Jan, 2024

-
-

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

40mm to 200mm

40325 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(QUICK COUPLED PIPES)	-	19175	4.2 CBC-925,CBD-700, 5 Dimensions-500, 6.1 Visual Appearance-300, 7.1 Quality-4800, Acceptance-1600 7.2 Reversion-700+300(Speci), 7.3 Tensile Strength & Elongation-1100+250(Speci), 7.4 Quality -4800, Acceptance -1600,7.5 Density-500 7.5 MFR-1100
Cl.4.1(Quick Coupled Male and Female Couplers)	-	1050	-
4.1 .1.2.1(HDPE couplers)	-	6450	Density (2x500) Rs. 1000 Melt Flow Rate(2x1100) Rs. 2200 Carbon Black Content(2x925) Rs. 1850 Carbon Black Dispersion(2x700) Rs. 1400
4.1 .3(Workmanship and Appearance)	-	300	-
Cl 4.1.4(Holding attachments for coupler parts)	-	0	-
4.1.5(Rubber Ring)	-	5250	a. Shore Hardness of rubber ring (before & after ageing) Rs.750 b. Colour of rubber ring Rs.300 c. Ageing charges for rubber ring (70 °C/7days) Rs. 4200 (Conditioning/Specimen)
6.1.1, 6.1.1.1(Leakage Test)	-	850	-
6.1.2, 6.1.2.1( Hydraulic Proof Test)	-	850	-
6.1.3, 6.1.3.1(Weldability Test)	-	6400	i) Quality Test for 165 hours at 80ºC- Rs. 4800 ii) Acceptance Test for 48 hours at 80ºC- Rs. 1600

Complete

06 Jan, 2024

-
-

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

General Requirements Size – 20mm To 400mm

6275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	4100	VCM- Rs.3000 + K-Value- Rs.1100
5.1 Table-1 Fig.1(Dimension of Socket length)	-	250	-
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	250	-
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	250	-
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	575	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	850	-

Complete

06 Jan, 2024

-
-

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

Sockets Size – 20mm To 400mm and PVC PVC Resin

6525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1, Table-1, Fig-1(B)	-	6525		i)VCM Content-Rs.3000 ii)K-Value-Rs.1100 iii)Dimensions of fittings-500 iv)Socket length and Dimensions of mean inside diameter at mid-point of socket depth-Rs. 500 v)Opacity –Rs. 575 vi)Short Term Hydraulic Test- Rs. 850

Complete

06 Jan, 2024

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

Straight Reducers Upto 400mm

6525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2, 3.2.1, Fig 1(Manufacture)	-	0		-
3.1(General)	-	6252		i)VCM Content-Rs.3000 ii)K-Value-Rs.1100 iii)Dimensions of fittings-500 iv)Socket length and Dimensions of mean inside diameter at mid-point of socket depth-Rs. 500 v)Opacity –Rs. 575 vi)Short Term Hydraulic Test- Rs. 850

Complete

06 Jan, 2024

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

Caps Upto 400mm

6525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1(General)	-	6525		i)VCM Content-Rs.3000 ii)K-Value-Rs.1100 iii)Dimensions of fittings-500 iv)Socket length and Dimensions of mean inside diameter at mid-point of socket depth-Rs. 500 v)Opacity –Rs. 575 vi)Short Term Hydraulic Test- Rs. 850

Complete

06 Jan, 2024

-
-

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

Equal Tees Upto 400mm

6525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1(General)	-	6525		i)VCM Content-Rs.3000 ii)K-Value-Rs.1100 iii)Dimensions of fittings-500 iv)Socket length and Dimensions of mean inside diameter at mid-point of socket depth-Rs. 500 v)Opacity –Rs. 575 vi)Short Term Hydraulic Test- Rs. 850

Complete

06 Jan, 2024

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

Flanged Tail Pieces With Metallic Flanges -Upto 400

6525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1(General)	-	6525		i)VCM Content-Rs.3000 ii)K-Value-Rs.1100 iii)Dimensions of fittings-500 iv)Socket length and Dimensions of mean inside diameter at mid-point of socket depth-Rs. 500 v)Opacity –Rs. 575 vi)Short Term Hydraulic Test- Rs. 850

Complete

06 Jan, 2024

-
-

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

Threaded Adaptors -Upto 110mm

6525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1(General)	-	6525		i)VCM Content-Rs.3000 ii)K-Value-Rs.1100 iii)Dimensions of fittings-500 iv)Socket length and Dimensions of mean inside diameter at mid-point of socket depth-Rs. 500 v)Opacity –Rs. 575 vi)Short Term Hydraulic Test- Rs. 850

Complete

06 Jan, 2024

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

90 Degree Bends -Upto 400mm

6525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1(General)	-	6525		i)VCM Content-Rs.3000 ii)K-Value-Rs.1100 iii)Dimensions of fittings-500 iv)Socket length and Dimensions of mean inside diameter at mid-point of socket depth-Rs. 500 v)Opacity –Rs. 575 vi)Short Term Hydraulic Test- Rs. 850

Complete

06 Jan, 2024

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET Amritsar

P.O. Rayon & Silk Mills, Amritsar, Amritsar, Punjab, 143105

1832258938 [email protected]

Scope List