BIS - LIMS (Laboratory Information Management System)

Indian Rubber Manufacturers Research Association

Plot No. 254/1B, Road no. 16V, Wagle Industrial Estate, Thane, Thane, Maharashtra, 400604

2267873200 [email protected]

Scope List

Reset

14 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 9873 : Part 3 (2017)

Safety of toys: Part 3 migration of certain elements (Second Revision)

Safety Requirements for Toys: Migration of Certain Elem

4000 View breakup
Rs. 4000/- per product(25% Discount for BIS Samples)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	4000	-

Complete

-
-

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

Flammability (Safety of Toys)

12000 View breakup
Rs. 5000/- 25% Discount for BIS Samples)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2-5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	3000	-
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	3000	-
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	3000	-
4.5-5.5(Soft-filled toys-Test for soft-filled toys )	-	3000	-

Complete

-
-

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

Rubber Hose for LPG-Specific Part 2 Domestic/Commercial

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(General)	-	100	-
Clause 4.2.2 (a)(Reinforcement)	-	100	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	100	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	100	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	100	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	500	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	500	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	500	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	500	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	1500	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	500	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	0	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	0	-
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	0	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	0	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	0	-
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	0	-
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	0	-
Clause 5.2.1(BIS Certification Marking )	-	0	-
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	500	-

Complete

-
-

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

Rubber Hose for LPG-Specification Part 1 Industrial App

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 (General)	-	100	-
Clause 4.2.2(Reinforcement)	-	100	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	100	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	100	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	100	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- cover)	-	500	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	500	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	500	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	500	-
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	500	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	1500	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	500	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	0	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 2.5 MPa; )	-	0	-
Clause 5.2 (c)(Marking Nominal bore )	-	0	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	0	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	0	-
Clause 5.2 (f)(Marking IS 9573 (Part 1) )	-	0	-
Clause 5.2.1(BIS Certification Marking )	-	0	-

Complete

-
-

IS 10733 (1983)

Specification for electrically bonded road and rail tanker hose of rubber, resistant to petroleum products

- View breakup
Rs. 20,150/- (With 20% Discount for BIS Samples)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 12585 (1988)

Specification for thermoplastic hoses (Textile Reinforced) for water - General purpose

Specification for Thermoplastic Hoses For water

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Construction)	-	100	-
Cl 4.2(Dimensions & Tolerances)	-	100	-
Cl 4.3.1 & Appendix A(Loss in Mass on Heating)	-	3000	-
Cl 4.3.2(Adhesion)	-	2400	-
Cl 4.3.3(Pressure Requirements)	-	2000	-
Cl 4.3.4(Minimum Bend Radius)	-	500	-
Cl 4.3.5(Low Temperature Flexibility)	-	6400	-

Complete

-
-

IS 4148 (1989)

Surgical rubber gloves - Specification (First Revision)

SURGICAL RUBBER GLOVES

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.4(Manufacture)	-	-	-
4.2(Dimensions Fig 1 and Table 1)	-	-	-
4.3(Thickness)	-	-	-
4.4.1(Physical Properties)	-	-	-
4.4.2(After accelerated aging at 70 + 1OC for 240 h )	-	-	-
4.4.3(After heat ageing in autoclave)	-	-	-
4.4.4(Tension Set)	-	-	-
4.5(pH of Aqueous Extract )	-	-	-

Complete

-
-

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

FLEXIBLE RUBBER TUBING FOR LIQUEFIED PETROLEUM GAS

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.2(The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-	100	-
Cl4.3.1(The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-	200	-
Cl4.3.2(it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-	200	-
Cl.4.4,(Cl.4.4.1)(when tested in accordance with the method given in AnnexureA. It shall fit over the standard and oversize metal nozzle shown in Fig1,2 and 3)	-	1300	-
Cl.4.4,(Cl.4.4.2)(it shall remain atatched to both nozzles throught the test period)	-	1300	-
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the increase in the outside diametre of the tubing ,Also the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	1000	-
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	1000	-
Cl.4.6(Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-	500	-
Cl.4.7(Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-	1000	-
Cl.4.8.1(Flexible test , Annexure B The gas pressure shown on the manometre shall not drop by more than 1 Kpa)	-	1000	-
Cl4.8.2(The tubing shall be so flexible that it will make contact with a cylinder former of radius 68 mm for at least 110 deg of its circumference when the tubing is placed over the framer and a mass of 1.6 kg is attcahed to each end)	-	1000	-
Cl.4.9(Crushing test , )	-	1000	-
Cl.4.10(Resistance to lpg ,Annexure c Shall not be more than 15 % of the initial mass of the tubing and the amount of exctractable matter shall not excced 10 percent of the iniital mass of te tubing)	-	2000	-
Cl.4.11(Resistance to Ozone ,Annexure D Shall not show any breakage on surface or crack or defects)	-	3000	-
Cl.4.12(Burning behaviour on exposure to small flame,Annexure E tubing shall not burn to either of the outer marks within the test period of 45 seconds)	-	1000	-

Complete

-
-

IS 7466 (1994)

Rubber gaskets for pressure cookers - Specifications (First Revison)

RUBBER GASKETS FOR PRESSURE COOKERS

11800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Workmanship and Finish )	-	100	-
3.4-Table 1(i)(Requirements of Rubber Used for Gaskets-Hardness IRHD)	-	500	-
3.4-Table 1(ii)(Requirements of Rubber Used for Gaskets-Tensile strength,)	-	500	-
3.4-Table 1(iii)(Requirements of Rubber Used for Gaskets-Elongation at break)	-	500	-
3.4-Table 1(iv-a)(Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing 3 days in Aie-oven Change From Original Value))	-	500	-
3.4-Table 1(iv-b)(Requirements of Rubber Used for Gaskets-Tensile strength(After ageing 3 days in Aie-oven Change From Original Value))	-	500	-
3.4-Table 1(iv-c)(Requirements of Rubber Used for Gaskets-Elongation at break(After ageing 3 days in Aie-oven Change From Original Value))	-	500	-
3.4-Table 1(v-a)(Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing in an autoclave Change From Original Value))	-	1500	-
3.4-Table 1(v-b)(Requirements of Rubber Used for Gaskets-Tensile strength(After ageing in an autoclave Change From Original Value))	-	500	-
3.4-Table 1(vi)(Compression set)	-	1000	-
3.5-ANNEX C(PERFORMANCE TEST FOR PRESSURE COOKER )	-	1100	-
Clause 4.3 Table 1(Zinc oxide)	-	1000	-
Clause 3.4 Table 1(Heavy metal content)	-	1500	-
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	500	-
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	0	-
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	0	-
Strength requiement for Seat Cl9.1(The seat shall withstand the load of 1150 N for 30 minutes without permanent distortion of the seat or the hinge fittings or damage to any finish.)	-	0	-

Complete

-
-

IS 15466 (2004)

Rubber seals for hydraulic gates - Specification

RUBBER SEAL FOR HYDRAULIC GATES.

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(The basic polymer shall benatural rubber or a co-polymer of butadiene and styreneor a blend of both and the compound shall contain not less than 70 %by volume,of the basic polymer and the remainder shall consists of reinforcing carbon black,zinc oxide,accelarators,antioxidents,vulcanizing agents and plasticizers.)	-	-	-
4,Table1(Physical requirements)	-	-	-
4,Table2(Shore A durometer hardness,IS 3400 (part 23):2002)	-	-	-
4,Table3(Elongation at break%,Min,IS 3400 (part 1):1987)	-	-	-
4,Table4(Tensile strength,N/mm2,Min,IS 3400 (part 1):1987)	-	-	-
4,Table5(Mass of water absorbed in 7 days,%,Max IS 3400 (part 6):1983)	-	-	-
4,Table6(Tensile strength after ccelerated aging test of 48 h in oxygen at 70+/- 1 dec C and 2.1 +/- 0.1 N/mm2 pressureIS 3400 (part 4):1987 andIS 3400 (part 1):1987)	-	-	-
4,Table7(Low temperature brittleness as per Annex A)	-	-	-
5,Table 2(Type,Shape and)	-	-	-
6(Additional requirement of Cladded seals)	-	-	-

Complete

-
-

IS 15627 (2005)

Automotive vehicles - Pneumatic tyres i?or two and three - Wheeled motor vehicles - Specification

97000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1.1.1- Refer Annex C Col 2 and Annex D(test method )(Tyre dimensions/Section width)	-	1500	-
4/4.1.1.2- Refer Annex C Col 2 and Annex D(test method )(Tyre outer diameter)	-	1500	-
4/4.2.1 /4.2.2/4.2.3,Annex E ,Table 12(Load/Speed Performance Test)	-	15000	-
4/4.3 Refer Annex F,Table 13(Dynamic Growth of~Tyres)	-	8000	-
4.5 refer Table 17 and Annex H(Endurance Test)	-	57000	-
4.6/4.6.1(Tread Wear Indicators)	-	3500	-
4.4,Refer Table 14 to 16 and Annex G(Tyre Strength Test (Plunger Test) )	-	10000	-
5(Markings)	-	500	-

Complete

-
-

IS 15633 (2005)

Automotive vehicles - Pneumatic tyres for passenger car vehicles - Diagonal and radial ply - Specification

AUTOMOTIVE VEHICLES –PNEUMATIC TYRES FOR PASSENGER CAR

95500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1.1.1- Refer Annex B Col 2 and Annex D(test method )(Tyre dimensions/Section width)	-	1500	-
4/4.1.1.2- Refer Annex B Col 2 and Annex D(test method )(Tyre outer diameter)	-	1500	-
4/4.2.1 /4.2.2/4.2.3,Refer Annex D ,Table 13(Load/Speed Performance Test)	-	15000	-
4.3/4.3.1/4.3.2 Refer Annex E and Table 14( Endurance Test)	-	57000	-
4.4/4.4.1/4.4.2 Refer Annex F and Table 15 and 16(Bead Unseating Resistance Test for Tubeless Tyre )	-	6500	-
4.5.1(Tread-Wear -Indicators)	-	3500	-
4.6. Refer Annex G ,Table 17 and 18(Tyre.Strength Test)	-	10000	-
5(Markings)	-	500	-

Complete

-
-

IS 13098 (2012)

Automotive vehicles - Tubes for pneumatic tyres - Specification (First Revision)

AUTOMOTIVE VEHICLES – TUBES FOR PNEUMATIC TYRES

0 View breakup
-

Clause No.	Exclusion	Remark
3/3.3(Uniformity(The Thickness shall not vary from the arithmetic mean of the readings by ± 17.5 % at any point in longitudinal direction :-Crown centre,Base centre,Side wall - 1,Side wall - 2))	-	-
4/4.1.1(Elongation at break (Class A' Tubes))	-	-
4/4.1.1(Elongation at break (Class B' Tubes))	-	-
4/4.1.2( Strength of Splice (Class A' Tubes))	-	-
4/4.1.2( Strength of Splice (Class B' Tubes))	-	-
4/4.1.3 Refer annex B(Set After Ageing(Class A' Tubes))	-	-
4/4.1.3 Refer annex B(Set After Ageing(Class B' Tubes))	-	-
3/3.1 (for valve refer IS 9081)(MATERIALS, FORM AND FIT)	-	-
4/4.1.4 Refer annex C(Accelerated Ageing(Both Class A and Class B))	-	-
5(AIR TIGHTNESS)	-	-

Complete

-
-

IS 15636 (2012)

Automotive vehicles - Pneumatic tyres for commercial vehicles - Diagonal and radial ply - Specification (First Revision)

94000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Section width of tyre)	-	1750	-
4.1.1.2(Tyre outer diameter)	-	1750	-
4.2(Endurance test)	-	67000	-
4.3.1(Load/Speed performance test)	-	18000	-
4,4,1(Tread -wear indicators)	-	3000	-
4.5(Tyre strength test (Plunger rest))	-	20000	-
5, 8(Marking)	-	500	-

Complete

-
-

Bureau of Indian Standards

The National Standards Body of India

Indian Rubber Manufacturers Research Association

Plot No. 254/1B, Road no. 16V, Wagle Industrial Estate, Thane, Thane, Maharashtra, 400604

2267873200 [email protected]

Scope List

No Record Found