BIS - LIMS (Laboratory Information Management System)

NATIONAL TEST HOUSE(SOUTHERN REGION)

GOVT.OF INDIA,CSIR ROAD,TARAMANI., Chennai, Chennai, Tamil Nadu, 600113

9790824056 [email protected]

Scope List

Reset

33 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 513 : Part 2 (2016)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Workmanship)	-	1000	-
Cl 7(UTM)	-	3000	-
Cl. 7.2 Table 7(Bend Test)	-	1000	-
Cl 10(Length, Width & Thickness)	-	1000	-
Cl. 7.3 Table 4A & 4B(Tensile Strain Hardening)	-	3000	Additional Charges
Cl. 8.5.3 Table 6(Surface Roughness)	-	1000	Additional Charges

Complete

-
-

IS 277 (2018)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8.1(UTM)	-	3000	-
Cl 8.2(Press)	-	1000	-
Cl 14(Length, Width & Thickness)	-	1000	-
7.1 & 10.2(Mass of Coating: Single Spot Test)	-	1000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	1000	-

Complete

-
-

IS 16415 (2015)

Composite cement - Specification

0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 and Table 3 i(Fineness IS 4031(Part 2))	-	1118	ALL FEES ARE INCLUDING GST
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	590	ALL FEES ARE INCLUDING GST
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1118	ALL FEES ARE INCLUDING GST
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	590	ALL FEES ARE INCLUDING GST
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	590	ALL FEES ARE INCLUDING GST
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	1118	ALL FEES ARE INCLUDING GST
Cl. 6.1,Table 2(Alkali content)	-	0	-
Cl. 6.1,Table 2(Insoluble residue)	-	0	-
Cl. 6.1,Table 2(Chloride content)	-	0	-
Cl. 6.1,Table 2(Loss on ignition)	-	0	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	0	-
Cl. 6.1,Table 2(Magnesia)	-	0	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	0	-

Complete

-
-

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	900	NIL
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	800	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	900	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	900	-
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1000	-

Complete

-
-

IS/ISO 22702 (2003)

Uitility lighters - General consumer - Safety requirements

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0(marking )	-	0	-
3.2.1(Functional requirements-Flame heights)	-	1800	-
3.4(Functional requirements- Resistance to spitting or sputtering and flaring)	-	1800	-
3.5(Functional requirements- Flame extinction)	-	1800	-
4.8(Structural-integrity requirements- Compatibility with fuel)	-	1800	-
5.0(Refilling of utility lighters)	-	1800	-
3.6(Functional requirements- voluntary displacement.)	-	1800	-
4.2(Structural-integrity requirements- 4.2 Resistance to dropping )	-	1800	-
4.3(Structural-integrity requirements- Resistance to elevated temperature)	-	1800	-
4.9(Structural-integrity requirements- Resistance to internal pressure)	-	1800	-
4.6(Structural-integrity requirements- Resistance to cyclic burn)	-	1800	-
4.5(Structural-integrity requirements- Resistance to continuous burn)	-	2000	-

Complete

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Earthed & Unearthed upto 1.1kV and DC upto 1.5kV

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	1000	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	500	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	500	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
8.1(CONSTRUCTION : CONDUCTOR)	-	500	-
8.2(CONSTRUCTION : CONDUCTOR)	-	500	-
9.2(INSULATION : Thickness of Insulation)	-	500	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	500	-
9.4(INSULATION : Application of Insulation)	-	500	-
10.1(CORE IDENTIFICATION)	-	500	-
10.2(CORE IDENTIFICATION)	-	500	-
10.3(CORE IDENTIFICATION)	-	500	-
11.1(LAYING UP OF CORES)	-	500	-
11.2(LAYING UP OF CORES)	-	500	-
12.1(INNER SHEATH)	-	500	-
12.2(INNER SHEATH)	-	500	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	500	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	500	-
13.1.1(ARMOURING : Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.4(ARMOURING : Joints)	-	1000	-
13.5.1(ARMOURING : Resistance)	-	1000	-
13.5.2(ARMOURING : Resistance)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(OUTER SHEATH)	-	1000	-
14.3(OUTER SHEATH : Colour )	-	1000	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	1000	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	1000	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	1000	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	1000	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	1000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 d)4)(Hot deformation : Insulation )	-	1000	-
15.1 d)4)(Hot deformation : Sheath )	-	1000	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	1000	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	1000	-
15.1 d)6)(Heat shock test- Insulation )	-	1000	-
15.1 d)7)(Thermal stability- insulation )	-	1000	-
15.1 d)7)(Thermal stability- Sheath )	-	1000	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1000	-
15.1 e)(Insulation resistance test : IR Constant )	-	1000	-
15.1 f)(High voltage test ( water immersion test ))	-	1000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	1000	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	1000	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	1000	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1000	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1000	-
16.4(Flammability Test)	-	1000	-
16.5(Oxygen Index Test)	-	5000	-
16.6(Flame Retardance Test on Single Cables)	-	1000	-
16.9(Test for Halogen Acid Gas Evolution)	-	5000	-
16.1(Temperature Index)	-	5000	-
Cl No. 16.10(Smoke density test)	-	5000	-
Table 4(Copper purity test)	-	1000	-
16.4(Flammability Test- Un affected portion)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	-

Complete

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

27000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8.1(UTM)	-	4000	Rs 4000/- for 32mm, Rs 3000/- for 16mm-28mm, Rs 2000/- for 8mm-12mm.
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228)	-	1180	INCLUDING 18 % GST
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	1000	-
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	15000	Rs 10000/- for 8mm- 12mm, Rs 15000 for 16mm- 32mm.
Cl 7.2(Weight)	-	1000	-
Cl 8.1(UTM)	-	4000	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1000	-

Complete

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Conductor - Material)	-	1000	-
5.1(Insulation)	-	500	-
5.2(Application )	-	500	-
12(CONSTRUCTION Core Identification)	-	500	-
4.2(Conductor resistance test)	-	500	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	500	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	500	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	500	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	500	-
Table 1 iii) c) 3)(Elongation variation)	-	500	-
Table 1 iii) c) 3)(TS variation)	-	500	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	500	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	500	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	500	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	500	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	500	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	500	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	500	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	500	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	500	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	500	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	500	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	500	-
10.4(Flammability test- Unaffected portion)	-	500	-
10.4(Flammability test-Burning after flame removal)	-	500	-
4.1(Annealing test (for copper))	-	500	-
4.1(Wrapping test (for Al))	-	500	-
4.1(Tensile test (for Al)- After Stranding)	-	500	-
4.1(Tensile test (for Al)-Before Stranding)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	500	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	500	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	500	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	500	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	500	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	500	-
10.5(Oxygen index)	-	5000	-
10.7(Temperature index)	-	5000	-
10.6(Halogen evolution)	-	5000	-
10.8(Smoke density rating)	-	5000	-
table 1 e) 3) (IR constant- max. Temp)	-	500	-
table 1 e) 3) (IR constant- Room temp )	-	500	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	500	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	500	-
10.1(HV (water immersion))	-	1000	-
10.1(HV (water immersion))	-	1000	-
10.2(HV (room temperature))	-	1000	-
9(Overall dimensions)	-	500	-
8.3(Minimum thickness of Sheath)	-	500	-
8.3(Avarage thickness of Sheath)	-	500	-
5.3(Minimum thickness of insulation)	-	500	-
5.3(Avarage thickness of insulation)	-	500	-

Complete

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 10.3(UTM)	-	3000	-
Cl 11.3(Press)	-	1000	-
Cl 12(Sudden Load Applied)	-	0	NA
Cl 15(Length, Width & Thickness)	-	1000	-
Cl 11.3(Press)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-

Complete

-
-

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 iii b(Setting Time Final)	-	590	ALL FEES ARE INCLUDING GST
7 Table-3 iii a(Setting Time Initial)	-	590	ALL FEES ARE INCLUDING GST
7 Table-3 ii b(Expansion by Autoclave)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 ii a(Expansion by Le Chatelier)	-	590	ALL FEES ARE INCLUDING GST
7 Table-3 i.(Fineness)	-	1118	ALL FEES ARE INCLUDING GST
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	0	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	0	-
6.1 Table-2 iii.(Insoluble residue)	-	0	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	0	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	0	-
6.1 Table-2 vi(Loss on ignition)	-	0	-
6.1 Table-2 vii(Chloride content)	-	0	-
6.1 Table-2 viii(Alkali content)	-	0	-

Complete

-
-

IS 455 (2015)

Portland slag cement - Specification

0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table 1 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	590	ALL FEES ARE INCLUDING GST
7 Table 1 iii a(Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-	590	ALL FEES ARE INCLUDING GST
7 Table 1 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	590	ALL FEES ARE INCLUDING GST
7 Table 1 i(Fineness IS 4031(Part 2))	-	1118	ALL FEES ARE INCLUDING GST
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	0	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	0	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	0	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	0	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	0	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	0	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	0	-

Complete

-
-

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

5900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1118	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	590	ALL FEES ARE INCLUDING GST
7 -Table 2- i(Fineness 4031 Part 2)	-	1118	ALL FEES ARE INCLUDING GST

Complete

-
-

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	2500	Rs 4000/- with micro elements, Rs 2500/- without micro elements.
8(Mechanical and Physical Properties)	-	4000	(i) Cl. 8.1, Tensile Test, Rs 3000, (iI) Cl. 8.4, Bend Test, Rs 1000
Cl 9(Workmanship)	-	4000	Additional charges (i) Cl. 9.3, Strain Ageing, Test Fee, Rs 3000.00, (ii) Cl. 9.5, Surface Finish, Test Fee, Rs 1000.00
Cl 9(Workmanship)	-	4000	Additional charges (i) Cl. 9.3, Strain Ageing, Test Fee, Rs 3000.00, (ii) Cl. 9.5, Surface Finish, Test Fee, Rs 1000.00
Cl 11(Length, Width & Thickness)	-	1000	Thickness measurement, mm.
Cl 9.5(Workmanship)	-	1000	Cl. 9.5, Surface Finish, Test Fee, Rs 1000.00
Cl 8(UTM)	-	3000	(i) Cl. 8.1, Tensile Test, Rs 3000
Cl 11(Length, Width & Thickness)	-	1000	Thickness measurement, mm.
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	2000	Included in complete test charges.
Cl 11(Length, Width & Thickness)	-	1000	Included in complete test charges.
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	3000	Additional charges not included in complete test charges.
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	3000	Additional charges not included in complete test charges.
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	3000	Additional charges not included in complete test charges.
Cl. 8.7(Bake Hardening Index)	-	3000	Additional charges not included in complete test charges.
Cl 10(Workmanship)	-	1000	-
Cl. 9 Table 8(Surface roughness)	-	1000	-

Complete

-
-

IS 12776 (2002)

Galvanized strand for earthing - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Freedom From Defects (IS 12776))	-	250	-
5.3(Joints in wires (IS 12776))	-	250	-
6- Annex-A, Sl-2(Size of the wire (IS 12776))	-	250	-
6- Annex-A, Sl-8(Lay (IS 12776))	-	250	-
8.1-Annex-A,Sl-9(Breaking Force of Strand (IS 12776))	-	1500	-
8.2-Annex-A,Sl-6(Elongation of wire, IS 10810(Part-37))	-	1500	-
8.3-Annex-A,Sl-12(Resistance at 200 C (IS 12776))	-	1500	-
8.4(Wrapping Test (IS 12776))	-	500	-
8.5-Annex-A-Sl-7a(Amount of zinc Coating (IS 6745))	-	1000	-
8.5-Annex-A-Sl-7b(Uniformity of Coating (IS 2633))	-	1000	-
8.5-Annex-A-Sl-4(Torsion Test IS 10810(Part-37))	-	500	-
8.2-Annex-A,Sl-3(Tensile Strength of wire IS 10810(Part-37))	-	1500	-

Complete

-
-

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 & 8.2(Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	4000	-
6 & 8.2(Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Copper- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
7.1.1(Diameter of Core Wire)	-	0	Included in Tensile Test charges
7.1.2(Length of Electrodes)	-	0	Included in Tensile Test charges
7.2.1(Contact End)	-	0	Included in Tensile Test charges
7.2.2(Arc striking End)	-	0	Included in Tensile Test charges
7.3(Concentricity of Flux covering with core wire)	-	0	Included in Tensile Test charges
7.4(Defects of Core wire and Coverings)	-	0	Included in Tensile Test charges
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-	0	13000
9.1.2 Table 6 ( Yield Stress -Annex F)	-	0	Included in Tensile Test charges
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-	0	Included in Tensile Test charges
9.1.3 Table 6 ( Impact Strength-Annex F)	-	0	Included in Tensile Test charges
9.2(Butt Weld Bend Test-IS 1599)	-	8000	-
9.3(Running PerformanceTest-Annex H)	-	2000	-
9.4(Increased Metal Recovery Test-IS 13043)	-	3000	-
9.5(Diffusible Hydrogen Evaluation Test-IS 11802)	-	5000	-
9.6(Radiographic Test- IS 1182)	-	1000	-

Complete

-
-

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	100	-
10.a)(Packing)	-	300	-
10.b)(Packing)	-	0	-
10.c)(Packing)	-	0	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	100	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	100	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	100	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	100	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	100	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	100	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	100	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	100	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	100	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	100	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	500	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	0	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	0	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	100	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	100	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	500	-
8(Thermal Properties (Cl..8.4))	-	500	-
8(Thermal Properties (Cl..8.4))	-	500	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	500	-
8(Extreme Low Temperature (Cl.8.6))	-	500	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	-	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	-	-

Complete

-
-

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	800	nil
6.1(Manganese %)	-	800	nil
6.1(Phosphorus %)	-	800	nil
6.1(Sulphur %)	-	800	nil
6.1( Copper %)	-	800	nil

Complete

-
-

IS 4250 (1980)

Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	500	-
6(Classification- IS 302-1)	-	499.99	-
7.1(Marking- IS 302-1)	-	500	-
7.1(Marking- IS 302-1)	-	500	-
7.1(Marking- IS 302-1)	-	500	-
7.1(Marking- IS 302-1)	-	499.99	-
7.2(Marking)	-	500	-
7.4(Marking)	-	500	-
7.5(Marking)	-	500	-
7.6(Marking)	-	500	-
8( Protection Against Electric Shock, IS 302-1)	-	500	-
9(Starting, IS 302-1)	-	1000	-
10(Power Input and Current, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1500	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	1500	-
15.1(Moisture Resistance, IS 302-1)	-	1500	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1500	-
19(Abnormal Operation, IS 302-1)	-	1500	-
20(Stability & Mechanical Hazards, IS 302-1)	-	1500	-
21(Mechanical Strength, IS 302-1)	-	1000	-
25(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	-
27(Provision for Earthing, IS 302-1)	-	1000	-
28(Screws & Connections, IS 302-1)	-	1000	-
29(Clearances and Distances through Insulation, IS 302-1)	-	1000	-
30(Resistance to Heat, Fire, Tracking, IS 302-1)	-	1500	-
22.2(Construction)	-	500	-
34.2(Operational tests- Grinding coffee (for machines which have a dry grinding arrangement))	-	2000	-
34.3(Whisking egg whites )	-	1500	-
34.4(IDLI batter-Grinding of black gram)	-	1000	-
34.4(IDLI batter-Grinding of rice)	-	1000	-
34.5.1 (a)(Operational test for juicers )	-	1000	-
37(Strength of Assembly )	-	1000	-

Complete

-
-

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3(Marking, Cl. 6.4 of IS 9537-1)	-	1000	-
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	1000	-
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	1000	-
7.3(Dimensions (Wall thickness), IS 9537-2)	-	1000	-
7.4(Screw threads, IS 9537-2)	-	1000	-
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	1000	-
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	2000	-

Complete

-
-

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

4950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	200	-
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	200	-
6.3(Standard Mark on Conduit)	-	100	-
7.1.1(Maximum and minimum outside diameter of socket)	-	500	-
7.2(Minimum inside diameter of conduit)	-	500	-
7.1.1 Table-2(Length of Socket end)	-	500	-
7.4(Unifomity of The wall Thickness)	-	500	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	500	-
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	500	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	500	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	500	-
10(Resistance to Heat -Ball presure test)	-	500	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	500	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	500	-
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	500	-

Complete

-
-

IS 1554 : Part 2 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 2 for working voltages from 3.3 kV up to and including 11 kV (Second Revision)

Earthed & Unearthed Cables

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CONDUCTOR)	-	600	-
4.1(INSULATION)	-	600	-
5.1(SCREENING)	-	600	-
6.1(FILLERS AND INNER SHEATH)	-	600	-
7.1(ARMOURING)	-	600	-
8.1(OUTER SHEATH)	-	600	-
9.1(CONDUCTOR)	-	1000	-
11.1(INSULATION)	-	1000	-
11.2(INSULATION : Thickness of Insulation)	-	1000	-
13.1(CORE IDENTIFICATION)	-	600	-
14.1(LAYING UP OF CORES)	-	1000	-
15.1(INNER SHEATH (COMMON COVERING))	-	1000	-
15.4(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	1000	-
15.4.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	1000	-
16.1.1(ARMOURING : Application)	-	1000	-
16.1.3(ARMOURING : Direction of lay )	-	1000	-
16.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
16.4(ARMOURING : Joints)	-	1000	-
16.5(ARMOURING : Resistance)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
17.1(OUTER SHEATH)	-	1000	-
17.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	1000	-
17.3.2(Thickness of Outer Sheath : Armoured Cables)	-	1000	-
18.1 a) 1)(Tests on Conductor : Annealing test (for copper))	-	1000	-
18.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	-
18.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	1000	-
18.1 a) 3)(Tests on Conductor : Wrapping test ( for aluminium))	-	1000	-
18.1 a)4)(Tests on conductor : Conductor resistance test - Main conductor )	-	1000	-
18.1 a)4)(Resistance test - Neutral conductor )	-	1000	-
18.1 d) 1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
18.1 d) 1)(Phyaical tests for insulation : Elongation )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Tensile stregth )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Elongation )	-	1000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	1000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	1000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage )	-	1000	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
18.1 d) 4)(Hot deformation : Insulation )	-	1000	-
18.1 d) 4)(Hot deformation : Sheath )	-	1000	-
18.1 d) 5)( Loss of mass in air oven- Insulation )	-	1000	-
18.1 d) 5)( Loss of mass in air oven- sheath )	-	1000	-
18.1 d) 6)(Heat shock test- Insulation )	-	1000	-
18.1 d) 7)(Thermal stability- insulation )	-	1000	-
18.1 d) 7)(Thermal stability- Sheath )	-	1000	-
18.1 e)(Insulation resistance test : Volume Resistivity )	-	1000	-
18.1 e)(Insulation resistance test : IR Constant )	-	1000	-
19.7(High voltage test)	-	1000	-
19.8(Flammability test)	-	1000	-
19.11(Flame Retardance Test on Bunched Cables)	-	5000	-
19.1(Flame Retardance Test on Single Cables)	-	5000	-
19.13(Test for Halogen Acid Gas Evolution)	-	5000	-
19.9(Oxygen Index Test)	-	5000	-
19.14(Temperature Index)	-	5000	-
18.4(Optional Test : Cold Impact )	-	1000	-
20.2(IDENTIFICATION : Cable Identification)	-	0	-

Complete

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	500	-
9.3(Thickness of Insulation - Minimum)	-	500	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	500	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	1000	-
14.2(Colour of outer sheath)	-	1000	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	500	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	1000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	500	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	500	-
16.9(Oxygen Index Test)	-	5000	-
16.14(Temperature Index)	-	5000	-
16.1(Flame Retardance Test on Single Cables)	-	5000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	5000	-
17.1(Manufacturer'. ldeadentificatioa)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	500	-
15.4 (b)(Cold impact)	-	500	-
Cl No. 16.10(Smoke density test)	-	5000	-

Complete

-
-

IS 12330 (1988)

Specificatioon for sulphate resisting Portland cement

11180 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Fineness 4031 Part 2)	-	1118	ALL FEES ARE INCLUDING GST
5.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	590	ALL FEES ARE INCLUDING GST
5.2.1(Expansion by Autoclave- 4031 Part 3)	-	1118	ALL FEES ARE INCLUDING GST
5.3 a)(Setting Time Initial- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
5.3 b)(Setting Time Final- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
5.5 i)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
5.5 ii)(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
5.5 iii)(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
4.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	700	-
4.1 - Table - 1 iii(Magnesia - Cl 4.8 of IS 4032:1985)	-	700	-
4.1 - Table - 1 iv(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	700	-
4.1 - Table - 1 v(Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-	700	-
4.1 - Table - 1 vi(Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate ( C4AF + 2C3A ) - Cl 4 of IS 4032:1985)	-	700	-
4.1 - Table - 1 vii(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	700	-

Complete

-
-

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Al alloy stranded conductor

5400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	600	-
7.1 Table-1(Dimensional measurement of wires)	-	600	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor )	-	600	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	600	-
9.3(Direction of Lay)	-	600	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	1000	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	1000	-
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	-
12.3 Table 1(Elongation Test- After Stranding)	-	1000	-
12.4 Table 1(Resistance of Aluminium wire)	-	1000	-
9.2(Lay Ratio 24 wire layer)	-	600	-
9.2(Lay Ratio 18 wire layer)	-	600	-
9.2(Lay Ratio 12 wire layer)	-	600	-
9.2(Lay Ratio 3/6 wire layer)	-	600	-
Strength requiement for Seat Cl9.1(The seat shall withstand the load of 1150 N for 30 minutes without permanent distortion of the seat or the hinge fittings or damage to any finish.)	-	1500	-

Complete

-
-

IS 8783 : Part 4 : Sec 1 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for indmdual wires: Sec 1 HR PVC insulated wires (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3.1 (Conductor)	-	500	-
Cl.4(Material)	-	500	-
Cl.5.1.1 (Dimensions)	-	500	-
Cl 6(Resistance Test)	-	1000	-
Cl 4.1.2 (Visual examination)	-	500	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile strength )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile Strength)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation at Break )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Water absorption (Gravimetric) )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Hot deformation Test )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Heat shock Test )	-	1000	-
Cl.4.1(Insulation )	-	1000	-
Cl.4.2(Application)	-	1000	-
Cl.4.3(Colour)	-	500	-
Cl.4.4(Overall Diameter)	-	500	-
Cl.4.5(Finish)	-	500	-
Cl.4.6(High Voltage Test Water Immersion )	-	1000	-

Complete

-
-

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Packing (As per Cl.5.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.1(Marking (As per Cl.6.1 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
6.2(Marking (As per Cl.6.2 of IS 8783 (Part 4/Sec 3) : 1995))	-	100	-
4(Conductor As per IS:8783(Pt 1):1995])	-	500	-
5([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-	500	-
5([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-	500	-
5([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-	500	-
5([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-	500	-
5([Cl 5 of IS:8783(Pt 1):1995 & 4.1 of IS:8783(Pt 3):1995])	-	500	-
4.1, table 1 & 2(Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-	500	-
4.1, table 1 & 3(Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-	500	-
4.1, table 1 & 4(Insulation (As per Cl.4.1 and Table 1 & 2 of IS 8783(Part4/Sec 3): 1995)	-	500	-
4.2(Insulation (As per Cl.4.2 of IS 8783(Part4/Sec 3): 1995)	-	500	-
4.3(Insulation (As per Cl.4.3 of IS 8783(Part4/Sec 3): 1995)	-	500	-
4.4(Insulation (As per Cl.4.4 of IS 8783(Part4/Sec 3): 1995)	-	500	-
4(Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-	500	-
4(Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-	500	-
4(Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-	500	-
4(Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-	500	-
4(Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-	500	-
4(Physical test for Insulation [Cl.4.1 of IS:8783(Pt-2):1995])	-	500	-
4((Cl.4.5 of IS 8783 (Part 4/Sec 3) : 1995))	-	1000	-
Clause No. 3(Insulation Resistance (Volume Resistivity at 27º C ))	-	1000	-
Clause No. 3(Insulation Resistance (Volume Resistivity at test temperature 90 º C ))	-	1000	-
Clause No. 3(Heat Shock)	-	1000	-
Clause No. 3(Shrinkage)	-	1000	-
Clause No. 3(Hot Deformation)	-	1000	-
Clause No. 3(Water absorption)	-	1000	-

Complete

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	500	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	500	-
5.1(Insulation)	-	500	-
6.1(Flexibility class)	-	500	-
6.2(Compactness)	-	500	-
6.2(No of strands)	-	500	-
6.2(Surface)	-	500	-
6.3(Protective barrier)	-	100	-
6.4(size of street lighting conductor)	-	500	-
6.5(Size of messenger conductor )	-	500	-
6.6(Joints in messenger conductor )	-	500	-
6.6(Direction of outer layer)	-	500	-
7.1(Insulation)	-	500	-
7.2( Thickness of insulation)	-	1000	-
7.3(Tolerance on thickness of insulation )	-	1000	-
7.4(Aplication of the insulation )	-	1000	-
7.5(Colour of the insulation )	-	500	-
8.1(Core identification)	-	500	-
8.2(Core identification)	-	500	-
8.3(Identification by other means)	-	500	-
9.1(Assembly (Laying up))	-	500	-
9.2(Assembly (Laying up))	-	1000	-
9.3(Direction of lay)	-	500	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	1000	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	1000	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	1000	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	1000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	1000	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	1000	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	1000	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	1000	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1000	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	1000	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	1000	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1000	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	1000	-
10.1 g)(High voltage test - IS10810:Part 45)	-	1000	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	1000	-

Complete

-
-

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Al stranded Conductors & Accessories for Overhead line

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	600	-
12.3, Table-1(Breaking load before stranding)	-	1500	-
12.3, Table-1(Breaking load after stranding)	-	1500	-
12.4(Wrapping test)	-	1000	-
12.5, Table 1(Resistance test)	-	1000	-
12.6, Table 3(Measurement of lay ratio)	-	1000	-
6(Freedom from defects)	-	500	-
Strength requiement for Seat Cl9.1(The seat shall withstand the load of 1150 N for 30 minutes without permanent distortion of the seat or the hinge fittings or damage to any finish.)	-	2500	-

Complete

-
-

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Aluminum conductors, galvanized steel reinforced

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	600	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	600	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	600	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	599.98	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	999.99	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	999.99	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	599.99	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	600	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	600	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	1000	-
13.7.2 (chem)(Mass of Zinc coating)	-	600	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	600	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	600	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	600	-
13.10 (elec)(Ultimate breaking load)	-	10000	-
13.11 (elec)(Stress-strain test)	-	10000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	600	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	600	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	600	-
Strength requiement for Seat Cl9.1(The seat shall withstand the load of 1150 N for 30 minutes without permanent distortion of the seat or the hinge fittings or damage to any finish.)	-	1000	-

Complete

-
-

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Rating)	-	500	-
6(Rating)	-	500	-
7(Classification)	-	500	-
7(Classification)	-	500	-
7(Classification)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
10(Protection against Electric Shock)	-	1000	-
11.1(Provision for earthing)	-	500	-
12(Terminals)	-	500	-
12.2.2(Connection of conductor)	-	500	-
12.2.3(Mechanical strength of terminals)	-	500	-
12.2.4(Resistance to corrosion)	-	1000	-
12.2.5(Undue damage to conductor)	-	500	-
12.2.7(Insertion of conductor)	-	500	-
13.2(b) Construction of switch [Cl 13.2])	-	500	-
13.3(c) Covers,cover plates and actuating members [Cl 13.3])	-	500	-
14(Mechanism [Cl. 14])	-	1000	-
15.1(Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-	1000	-
16.1(Insulation resistance [Cl. 16.1])	-	1000	-
16.2( Electric Strength [Cl. 16.2])	-	1000	-
17(Temperature- rise [Cl. 17])	-	1500	-
18(Marking and breaking Capacity[Cl. 18])	-	1500	-
18(Marking and breaking Capacity[Cl. 18])	-	1500	-
19(Normal Operation [Cl. 19] a) General & Operation)	-	1000	-
20(Mechanical Strength Test [Cl. 20])	-	1000	-
21(Resistance to Heat [Cl.21])	-	1500	-
22(Screw, Current Carrying Part And Connection [Cl.22])	-	1000	-
23.2(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	500	-
23(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	1000	-
19.2(Normal Operation (For AX type Switches) [Cl. 19.2])	-	1500	-
24.1.1(Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-	1000	-
25(Resistance to Rusting)	-	1000	-

Complete

-
-

Bureau of Indian Standards

The National Standards Body of India

NATIONAL TEST HOUSE(SOUTHERN REGION)

GOVT.OF INDIA,CSIR ROAD,TARAMANI., Chennai, Chennai, Tamil Nadu, 600113

9790824056 [email protected]

Scope List