BIS - LIMS (Laboratory Information Management System)

NSIC - Technical Services Centre

Aji Industrial, Bhavnagar Road, Opp Gujarat Forging, Rajkot, Rajkot, Gujarat, 360003

9959726692 [email protected]

Scope List

Reset

20 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 8472 (1998)

Pumps - Regenerative or clear, cold water

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15.2.2(d)(Max.self.priming time)	-	100	-
15.2.2(c)(Non-over-rated prime mover recommended by the manufacturer)	-	100	-
15.2.2(b)(Non overloading of the prime-mover I the declared operating head range)	-	100	-
15.2.2(a)(Discharge, total head as per Guarnteed duty point at rated voltage and speed)	-	100	-
15.2.1(f)(Max.self.priming time)	-	100	-
15.2.1(e)(Overall efficiency of pumpset)	-	100	-
15.2.2(Bare pumps)	-	100	-
15.2.1(d)(Full load speed of motor)	-	100	-
15.2.1(c)(Rated output of motor)	-	100	-
15.2.1(b)(Non overloading of the prime-mover I the declared operating head range)	-	100	-
15.2.1(a)(Discharge, total head, current and input power at the Guarnteed duty point)	-	100	-
15.2.1(Monoset pumps)	-	100	-
13.2.2(High Voltage test (cl.22.3.1(n) of IS 7538))	-	100	-
13.2.2(Insulation Resistance test (cl.22.3.1(m) of IS 7538))	-	100	-
13.2.2(Locked Rotor test (cl.22.3.1(e) of IS 7538))	-	100	-
13.2.2(Reduced voltage running test (cl.22.3.1(d) of IS 7538))	-	100	-
13.2.2(No load test (cl.22.3.1cb) of IS 7538))	-	100	-
13.2.2(Measurement of stator resistance test (cl.22.3.1(b) of IS 7538))	-	100	-
13.2(Three phase monoset pumps)	-	100	-
11.2(The nominal size of suction and delivery pipe of the pump shall be as specified in IS 1239 (Part 1),IS 4984, IS 4985 and IS 12231)	-	100	-
11.2(The pump casing should be of robust construction and shall be tested to withstand hydrostatic pressure as specified in 12.3.)	-	100	-
11.1(The pump shaft should be of adequate size to transmit the required power over the entire head range.)	-	100	-
11(General Requirements)	-	100	-
15(Guarntee on pump performance and tolerances)	-	100	-
15.2(Guarantee of Performance)	-	100	-
10.1 (c)(Design Features(Combination of Voltage and frequency variation))	-	100	-
10.1 (b)(Design Features(Frequency Rangings))	-	100	-
10.1(a)(Design Features(Voltage Rangings))	-	100	-
10.1(Design Features)	-	100	-
8.3(The direction of inlet and outlet flow passages)	-	100	-
8.1, 8.2(The direction of rotation of pumps)	-	100	-
7(Materials of Construction ( Shaft))	-	100	-
7(Materials of Construction ( Impeller))	-	100	-
7(Materials of Construction ( Casing/Chamber))	-	100	-
13(Tests for Electrical Performance)	-	100	-
13.1.2(Locked rotor test(cl.6.2(d) of IS 14582))	-	100	-
13.1(Single phase monoset pumps)	-	100	-
13.1.2(Measurement of stator resistance)	-	100	-
11.1(General Requirements)	-	100	-
7(Material of Constructional)	-	100	-
8(Direction of Rotation)	-	100	-
13.1.2(Insulation Resistance)	-	100	-
13.1.2(High Voltage test)	-	100	-
13.1.2(Break away torque Pull up torque)	-	100	-
13.1.2.1.2(Temperature Rise Test at Reduced Voltage)	-	1000	-
13.1.2.1.1(Temperature Rise Test at Rated Voltage)	-	1000	-
13.1.2(No Load Test at Rated Voltage)	-	100	-
13.1.2(No Load Test at Rated Voltage)	-	100	-
15.1(Guarantee of Workmanship and Material)	-	100	-
12.5(Self-Priming Test for Self-Priming Pumps)	-	100	-
12.4(Pump tests)	-	100	-
12.3.1(Hydrostatic Pressure Test)	-	100	-
12.3(Hydrostatic Pressure Test)	-	100	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	100	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	100	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Total head (m) and discharge (lps) at guaranteed duty point;)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-

Complete

14 Jun, 2022

-
-

IS 8472 (2019)

Centrifugal regenerative pumps for clear, cold water - Specification (Second Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
16.1(Marking)	-	100	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	100	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	100	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	100	-
12.3.1(Hydrostatic Pressure Test)	-	100	-
12.4(Pump tests)	-	1000	-
12.5(Self-Priming Test for Self-Priming Pumps)	-	100	-
15.2(Guarantee of Performance)	-	100	-
13.1.2(No Load Test at Rated Voltage)	-	100	-
13.1.2.1.1(Temperature Rise Test at Rated Voltage)	-	100	-
13.1.2.1.2(Temperature Rise Test at Reduced Voltage)	-	100	-
13.1.2(Break away torque Pull up torque)	-	100	-
13.1.2(High Voltage test)	-	100	-
13.1.2(Insulation Resistance)	-	100	-
8(Direction of Rotation)	-	100	-
7(Material of Constructional)	-	100	-
11.1(General Requirements)	-	100	-
13.1.2(Measurement of stator resistance)	-	100	-
13.1.2(Locked rotor test(cl.6.2(d) of IS 14582))	-	100	-
7(Materials of Construction ( Casing/Chamber))	-	100	-
7(Materials of Construction ( Impeller))	-	100	-
7(Materials of Construction ( Shaft))	-	100	-
8.1, 8.2(The direction of rotation of pumps)	-	100	-
8.3(The direction of inlet and outlet flow passages)	-	100	-
10.1(a)(Design Features(Voltage Rangings))	-	100	-
10.1(b)(Design Features(Frequency Rangings))	-	100	-
10.1(c)(Design Features(Combination of Voltage and frequency variation))	-	100	-
11.1(The pump shaft should be of adequate size to transmit the required power over the entire head range.)	-	100	-
11.2(The pump casing should be of robust construction and shall be tested to withstand hydrostatic pressure as specified in 12.3.)	-	100	-
13.2(Three phase monoset pumps)	-	100	-
13.2.2(Measurement of stator resistance test (cl.22.3.1(b) of IS 7538))	-	100	-
13.2.2(Reduced voltage running test (cl.22.3.1(d) of IS 7538))	-	100	-
13.2.2(Locked Rotor test (cl.22.3.1(e) of IS 7538))	-	100	-
13.2.2(Insulation Resistance test (cl.22.3.1(m) of IS 7538))	-	100	-
13.2.2(High Voltage test (cl.22.3.1(n) of IS 7538))	-	100	-
15.2.1(a)(Discharge, total head, current and input power at the Guarnteed duty point)	-	100	-
15.2.1(b)(Non overloading of the prime-mover I the declared operating head range)	-	100	-
15.2.1(c)(Rated output of motor)	-	100	-
15.2.1(d)(Full load speed of motor)	-	100	-
15.2.2(Bare pumps)	-	100	-
15.2.1(e)(Overall efficiency of pumpset)	-	100	-
15.2.1(f)(Max.self.priming time)	-	100	-
15.2.2(a)(Discharge, total head as per Guarnteed duty point at rated voltage and speed)	-	100	-
15.2.2(b)(Non overloading of the prime-mover I the declared operating head range)	-	100	-
15.2.2(c)(Non-over-rated prime mover recommended by the manufacturer)	-	100	-
15.2.2(d)(Max.self.priming time)	-	100	-

Complete

14 Jun, 2022

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

23954 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(DIMENSIONS-PIPE-Nominal Diameter)	-	590	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	590	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	590	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	590	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	590	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	590	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	590	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	590	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	590	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	590	-
7.2.1(DIMENSIONS-Socket)	-	590	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	590	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	590	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	590	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	708	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	708	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1180	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	531	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	10856	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	944	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	944	-
11.2(Resistance to External Blows at 0°C)	-	1121	-
10.3(Effect on Water Test)	-	2950	-
6.1.2(PVC Resin)	-	4071	-
10.7(Sulphated Ash Content)	-	1062	-

Complete

14 Jun, 2022

-
-

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

23954 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	590	Including GST
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	590	Including GST
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	590	Including GST
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	590	Including GST
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	590	Including GST
7.2.1(DIMENSIONS-Socket)	-	590	Including GST
7.2.1(DIMENSIONS-Socket)	-	590	Including GST
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	590	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	590	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	590	-
Clause 10.7(Sulphated Ash Content)	-	1062	-
11.2(Resistance to External Blows at 0°C)	-	1121	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	944	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	10856	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	531	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1180	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	708	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	708	-
10.3(Effect on Water)	-	2950	-
6.1.2(PVC Resin)	-	2950	-

Complete

14 Jun, 2022

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

13216 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1180	Including GST
9.5(Tensile Strength IS 12235(Part 13))	-	1121	Including GST
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1955	Including GST
9.3(Density IS 12235 (Part 14))	-	531	Including GST
9.2(Internal Diameter)	-	590	Including GST
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	1800	Including GST
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	1800	Including GST
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	1800	Including GST

Complete

14 Jun, 2022

-
-

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

13570 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	944	Including GST
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	590	Including GST
8.3.2(Inside Diameter ofEmitting Pipe)	-	295	Including GST
8.3.1(Wall Thickness ofEmitting Pipe)	-	295	Including GST
8.5(Resistance to Tension at Elevated Temperature)	-	1711	Including GST
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	590	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	590	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1888	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1298	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1711	-
8.3.4(Spacing ofEmitter Units)	-	295	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1121	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	1121	-
8.3.3(Flow Paths in Emitting Unit)	-	354	-
8.8(Determination of Emitting Unit Exponent)	-	708	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1121	-

Complete

14 Jun, 2022

-
-

IS 996 (2009)

Single phase a.c. induction motors for general purpose (Third Revision)

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
16.1(Marking and Diagram of connenctions)	-	100	-
10(Type of enclosures)	-	7500	-
11(Methods of cooling)	-	100	-
9.1(General construction (as per Cl. 9 & F-3))	-	100	-
9(General construction (as per Cl. 9 & F-3))	-	100	-
9.4.11(General construction (as per Cl. 9 & F-3))	-	100	-
9.4.13(General construction (as per Cl. 9 & F-3))	-	100	-
4.1(Rated Voltage)	-	100	-
4.2(Rated Frequency)	-	100	-
4.3(Rated Output)	-	100	-
4.4(Rated Speed)	-	100	-
7(Dimensions (Cl.App.F-4))	-	1000	-
9.5(Earthing)	-	100	-
9.5(Earthing)	-	100	-
9.5(Earthing)	-	100	-
17.3 (a)(No load test at rated voltage and frequency )	-	500	-
12.1.1(Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-	2000	-
12.5.1(Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-	5000	-
12.2(Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-	2000	-
12.7(Insulation resistance test)	-	250	-
13.1(High voltage test)	-	250	-
13.2(Moisture proofness)	-	1500	-
13.3(Leakage current test)	-	250	-
12.6(Vibration Severity)	-	250	-
15.2(Specific Requirements)	-	100	-
15.2(Specific Requirements)	-	100	-
9.0(Observation)	-	100	-
7.2(Dimensions)	-	100	-
11.0(Observation)	-	100	-
17.3 (j)(Observation)	-	100	-
9.5(Observation)	-	100	-
14.0(Observation)	-	100	-
16.0(Observation)	-	100	-
17.4 & 9.4.6.1(Observation)	-	100	-
17.3 (k)(Current)	-	100	-
17.3 (m)(Vibration)	-	100	-
17.3 (g)(Insulation Resistance)	-	100	-
17.3 (h)(Voltage)	-	100	-
17.3 (b)(Temperature)	-	1000	-
17.3 (e)(Temperature)	-	1000	-
17.3 (f)(Torque)	-	1000	-
17.3 (c)(Current, Torque)	-	100	-
17.3 (d)(Voltage, Current, Power, Frequency, Speed, Efficiency, Power factor, Slip)	-	100	-
17.3 (a)(Voltage, Current, Power, Frequency, Speed)	-	100	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 9283 (2013)

Motors for submersible pumpsets - Specification (Second Revision)

33600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Construction, IS 9283)	-	500	-
5.1.1(Construction, IS 9283)	-	500	-
5.1.3(Construction, IS 9283)	-	500	-
5.1.4(Construction, IS 9283)	-	500	-
5.2.1(Earthing, IS 9283)	-	100	-
5.2.2(Earthing, IS 9283)	-	100	-
5.2.3(Earthing, IS 9283)	-	100	-
5.2.4(Earthing, IS 9283)	-	100	-
5.2.5(Earthing, IS 9283)	-	100	-
5.3(Foreign Matter, IS 9283)	-	100	-
5.5(Finish of Bearings, IS 9283)	-	100	-
5.6(Balancing of Rotor, IS 9283)	-	500	-
7.1(Dimensions of Motors, IS 9283)	-	500	-
8(Type of duty, IS 9283)	-	100	-
13(Terminal Markings, IS 9283)	-	100	-
7.2.1(Tolerances, IS 9283)	-	100	-
7.2.2(Tolerances, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	100	-
15.3(Marking, IS 9283)	-	100	-
23(Leakage Current test, IS 9283)	-	200	-
5.1.2(Construction, IS 9283)	-	500	-
17.1(Performance values, IS 9283)	-	3000	-
17.1(Performance values, IS 9283)	-	3000	-
17.1(Performance values, IS 9283)	-	3000	-
17.1(Performance values, IS 9283)	-	3000	-
18.1(Overload test, IS 9283)	-	1500	-
19(Temperature rise test, IS 9283)	-	3500	-
19(Temperature rise test, IS 9283)	-	3500	-
20(High Voltage test, IS 9283)	-	500	-
21(Insulation Resistance test, IS 9283)	-	500	-
22(Speed, IS 9283)	-	500	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 6595 : Part 1 (2018)

Horizontal centrifugal pumps for clear, cold water - Specification: Part 1 agricultural and rural water supply purposes (Fourth Revision)

15840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Pump Test Verification of the Guarantee Cl.9.4 of IS 9137:2019 Cl. 9.4.1 Curves QH and Qη)	-	1000	-
10.1(Pump Test Verification of the Guarantee Cl.9.4 of IS 9137:2019 9.4.2 Efficiency)	-	1000	-
10.1(Pump Test Verification of the Guarantee Cl.9.4 of IS 9137:2019 9.4.3 Pump Power Input)	-	1000	-
8.1(Design Features Head Restrictions)	-	1000	-
8.1(Design Features Head Restrictions)	-	1000	-
8.2 As per fig 1 & 2(Design Features Minimum efficiency )	-	500	-
8.3(Design Features Shaft )	-	500	-
9.1(General Requirements Volute Casing)	-	1000	-
9.2(General Requirements Impeller)	-	1000	-
10(Pump Test Verification of guarante Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	1000	-
10(Pump Test Verification of guarante Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	1000	-
10(Pump Test Verification of guarante Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	1000	-
12.2.2(Pump Power Input )	-	1000	-
12.2.5(Vibrations )	-	1000	-
12.2.5(Noise level)	-	1000	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 8034 (2018)

Submersible pumpsets - Specification (Third Revision)

100 kW

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14(Marking)	-	100	ok
6.1 (a)(Constructional Features)	-	1000	ok
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
14(Marking)	-	100	-
6.1 (b)(Constructional Features)	-	100	-
6.1 (c)(Constructional Features)	-	100	-
6.1 (d)(Constructional Features)	-	100	-
6.1 (e)(Constructional Features)	-	100	-
6.1 (f)(Constructional Features)	-	100	-
6.2 (g)(Material of construction Part Sub Assembly Pump Shaft)	-	100	-
6.2 (h)(Material of construction Part Sub Assembly Suction Casing)	-	100	-
6.2.2.1(Gaskets, Seals and Packings)	-	100	-
6.2.2.2(Gaskets, Seals and Packings)	-	100	-
6.2.3(Gaskets, Seals and Packings)	-	100	-
6.2.4(Gaskets, Seals and Packings)	-	100	-
6.2.5(Gaskets, Seals and Packings)	-	100	-
7.1.1(Design features: Typical design features 0f components of pump)	-	100	-
7.1.2(Design features: Typical design features 0f components of pump)	-	100	-
7.1.3(Design features: Typical design features 0f components of pump)	-	100	-
7.1.4(Design features: Typical design features 0f components of pump)	-	100	-
7.1.5(Design features: Typical design features 0f components of pump)	-	100	-
7.1.6(Design features: Typical design features 0f components of pump)	-	100	-
8.1(General Requirements)	-	100	-
8.2(Casing)	-	350	-
8.3(Impeller)	-	350	-
8.4.1(Shaft)	-	100	-
8.4.2(Shaft)	-	100	-
8.5.1(Balancing)	-	250	-
8.5.2(Balancing)	-	250	-
8.7.1(Direction of Rotation)	-	50	-
8.7.2(Direction of Rotation)	-	50	-
8.8(Terminal Marking)	-	100	-
8.9.1(Typical Installation)	-	100	-
8.9.3(Typical Installation)	-	100	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	600	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	600	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	600	-
10.3(Hydrostatic Pressure Test)	-	250	-
11.1.1(Guarantee of Performance)	-	600	-
11.1.2(Guarantee of Performance)	-	600	-
11.1.3(Guarantee of Performance)	-	600	-
11.1.4(Guarantee of Performance)	-	600	-
11.1.5(Guarantee of Performance)	-	600	-
12(Guarantee of workmanship and material)	-	600	-
8.9(Typical installation)	-	100	-
8.5(Balancing of rotor)	-	100	-
8.6(Submersible cable)	-	100	-
8.7(Direction of Rotation)	-	100	-
7(Design features)	-	100	-
7.1.10(Voltage & Frequency variation)	-	100	-
6(Measurement of shaft extension)	-	100	-
6(Constructional Features)	-	100	-
11(Guarantee of Performance)	-	100	-
10(Pump Performance test)	-	1000	-
9.10 (a)(Insulation Resistance test)	-	100	-
9.10 (b)(High Voltage test)	-	100	-
9.10 (c)(Measurement of Stator Resistance)	-	100	-
9.10 (d)(No Load Test at Rated Voltage)	-	100	-
9.10 (e)(Reduced voltage Running up test)	-	100	-
9.10 (f) & (g)(Locked Rotor Test)	-	100	-
9.10 (h)(Leakage current test)	-	100	-
9.10 (j)(Temperature Rise Test at Rated Voltage)	-	1000	-
9.10 (k)(Temperature rise test at reduced voltage)	-	100	-
8.9.4c(Earthing)	-	100	-
7.1.7(Pump loading shall be as per 11.1.5)	-	100	-
7.1.9(prime mover electric motor suitable for the pumps shall be of contineous duty as specified in IS/IEC 60034-4 and as per IS 9283)	-	100	-
8.6.1(Flat/Round cables as per IS694 shall be used)	-	100	-
8.6.2(The size of the conductor shall be adequate and suitable for contineous use under water and in air. the length of the cable shall be minimum 2 m externallly unless otherwise specified by the customer)	-	100	-
8.6.3(The size and of the cable should be suitably selected so that the voltage drop between control panel and the mptor terminal does not exeed three percent of the rated voltage)	-	100	-
8.6.4(In case a joint is required to be made between the lead cable supplied with the motor and the user’s cable, a detailed procedure to make water tight joining shall be supplied by the motor manufacturer.)	-	100	-
8.9(Installation)	-	100	-
8.9.2(The pumpset shall be installed as per guidelines laid down in IS 14536 or as per the recommendation of the manufacturer)	-	100	-
8.9.4.1(Earthing of the motor shall be done as per IS 9283 in accordance with the relevant provisions of IS 3043.)	-	100	-
8.9.4.2(In case of PVC pipes used as discharge pipe, a separate non corrosive, low resistance conductor from motor earth terminal to control panel earth terminal shall be provided for earthing.)	-	100	-
8.9.4.3(In case non corrosive GI pipes and clamps are used for the purpose of earthing the motor, earthing connection may be made to the discharge pipe clamp and to the control panel earth terminal)	-	100	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 12615 (2018)

Line operated three phase AC motors (IE Code) "Efficiency classes and performance specification" (Third Revision)

Type Test up to 5.5 KW 9198 (0.12 kW to 30 kW) REVISED

32000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15.3.2(Marking)	-	100	Type Test up to 5.5 KW 9198 (0.12 kW to 30 kW) REVISED T ype Test Above 5.5 KW to 11 KW 11472 VERSION Included w.e.f. 05.02.2019.
15.2(Rating)	-	100	T ype Test Above 11 KW to 22 KW 20832 T ype Test Above 22 KW to 30 KW 30120 Optional Test (IP Test) 12000 Upto IP 44
18.3(BIS Certification Marking )	-	100	-
8.0(Earthing)	-	100	-
9.0(Terminal Marking)	-	100	-
11.0(DUTY AND RATING)	-	100	-
18.3(Marking)	-	100	-
16.2.1(Dimensions)	-	2000	-
16.1.1(Insulation Resistance Test)	-	1000	-
16.1.2(Measurement of Resistance of Windings of Stator)	-	1000	-
16.1.3(No Load Test)	-	1000	-
16.1.4(Locked Rotor Readings of Voltage, Current and Power Input at a Suitable Reduced Voltage)	-	1000	-
16.1.5(5 Reduced Voltage Running up Test at no-load (for squirrel cage motor up to 37 kW only))	-	1000	-
16.1.6(High Voltage Test)	-	1000	-
16.2.2(Locked Rotor Test)	-	1000	-
16.2.2.1(Locked Rotor Test)	-	1000	-
16.2.2.2(Locked Rotor Test)	-	1000	-
16.2.2.2.1(Locked Rotor Test)	-	1000	-
16.2.2.3(Determination of starting characteristics -locked rotor current)	-	1000	-
16.2.2.3.1(Direct proportion method)	-	1000	-
16.2.3(Full Load Test to Determine Efficiency, Power Factor and Slip)	-	6500	-
16.2.4(Temperature Rise Test)	-	3000	-
16.2.5(Momentary Overload Test)	-	800	-
16.3.1( Test for Vibration Severity of Motor)	-	500	-
16.3.3( Test for Degree of Protection by Enclosure)	-	6500	-
12.2(Pull up torque)	-	100	-
6(Method of cooling)	-	100	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 14220 (2018)

Openwell submersible pumpsets - Specification (First Revision)

28800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Design Features)	-	200	ok
10(Suction and Delivery Ends (Cl 17.2 of IS 5120))	-	200	ok
9(Efficiency)	-	500	-
8.1.1(Design Features)	-	500	-
8.1.4(Design Features)	-	500	-
8.1.5(Design Features)	-	100	-
8.1.5(Design Features)	-	100	-
10(Performance (Cl 17.1 of IS 5120))	-	2500	-
10(Fluid Passages (Cl 17.3 of IS 5120))	-	100	-
10(Draining Plugrs (Cl 17.4 of IS 5120))	-	100	-
10(Lantern Ring (Cl 17.5 of IS 5120))	-	100	-
10(Casing (Cl 17.6 of IS 5120))	-	1000	-
10(Impeller (Cl 17.7 of IS 5120))	-	1000	-
10(Shaft (Cl 17.8 of IS 5120))	-	200	-
10(Shaft Couplings (Cl 17.9 of IS 5120))	-	100	-
10(Bearings (Cl 17.10 of IS 5120))	-	100	-
10(Bearings (Cl 17.10.1 of IS 5120))	-	100	-
10(Bearings (Cl 17.10.2 of IS 5120))	-	100	-
10( Stuffing Boxes (Cl 17.11 of IS 5120))	-	100	-
10(Base Plates (Cl 17.12 of IS 5120))	-	100	-
10(Prime Mover (Cl 17.13 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14.1 of IS 5120))	-	100	-
10.2(Casing)	-	1000	-
10.3(Impeller)	-	1000	-
10.4.1(Shaft)	-	100	-
10.4.2(Shaft)	-	100	-
10.5.1(Balancing)	-	1000	-
10.5.2(Balancing)	-	1000	-
10.5.3(Balancing)	-	100	-
10.5.4(Balancing)	-	100	-
10.6.1( Provision for Earthing)	-	100	-
10.6.2( Provision for Earthing)	-	100	-
10.6.3( Provision for Earthing)	-	100	-
10.6.4( Provision for Earthing)	-	100	-
10.7.1(Terminal Marking and Direction of Rotation)	-	100	-
10.7.2(Terminal Marking and Direction of Rotation)	-	100	-
10.7.3(Terminal Marking and Direction of Rotation)	-	100	-
15.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	1000	-
15.2(Laboratory Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	1000	-
15.5(Hydrostatic Pressure Test)	-	1000	-
16.1.1( Guarantee of Performance)	-	1000	-
16.1.2( Guarantee of Performance)	-	1000	-
16.1.3( Guarantee of Performance)	-	1000	-
16.1.4( Guarantee of Performance)	-	1000	-
16.1.5( Guarantee of Performance)	-	1000	-
18.1.3(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
18.1(Marking)	-	100	-
7(Constructional features)	-	100	-
7.1(It is recognized that a number of materials of construction are available to meet the needs for pumps handling clear, cold water.)	-	100	-
7.2(Gaskets, seals and packings used for clear, cold water pumps shall conform to the applicable requirements specified in 5.2 of IS 5120.)	-	100	-
7.3(The motor shall be provided with a breathing attachment like bellows, diaphragm etc; to compensate the volumetric variation of water inside the motor due to change in the temperature.)	-	100	-
7.4(The motor shall be protected from ingress of well water, sand and other foreign matter by means of cable glands, rubber seals etc.)	-	100	-
7.5(All materials and components for the motor shall be suitable for application in respect of resistance and mechanical performance to protect it)	-	100	-
7.6(The rotor of the wet type open well submersible motor and rotor in water filled designed motor shall be provided with suitable coating from corrosion under water. However if suitable anticorrosion additive is added in the water, no separate protection on rotors is necessary.)	-	100	-
8(Design Features)	-	100	-
8.1.2(The multi-stage pump shaft may be guided through bearings, the bearings may be provided in stage casing, suction housing and discharge casing, while in case of intermediate bearings, suitable positions may be selected in the overall span.)	-	100	-
8.1.3(The pump may be equipped with replaceable bearing and wearing ring, wherever provided.)	-	100	-
8.1.4(The strainer on the suction shall offer the best compromise amongst restraining large solids from entering the pump and containing the suction losses to the minimum.)	-	100	-
8.1.5(The pump shall be capable to give discharge without overloading the prime mover within the permissible current at rated voltage and supply frequency at minimum +5 percent and minimum –15 percent of the guaranteed duty point head up to 30 m. Above 30 m, the pump shall be capable to give discharge without overloading the prime mover within the permissible current at rated voltage and supply frequency at minimum +10 percent and minimum –25 percent of the guaranteed duty point head.)	-	100	-
12(Cable)	-	100	-
12.1(Flat/Round cables as per IS694 shall be used)	-	100	-
12.1.2(The size of the conductor shall be adequate and suitable for contineous use under water and in air. the length of the cable shall be minimum 2 m externallly unless otherwise specified by the customer)	-	100	-
12.1.3(The size and of the cable should be suitably selected so that the voltage drop between control panel and the mptor terminal does not exeed three percent of the rated voltage)	-	100	-
12.1.4(In case a joint is required to be made between the lead cable supplied with the motor and the user’s cable, a detailed procedure to make water tight joining shall be supplied by the motor manufacturer.)	-	100	-
12.1.5(If four core cable is used, the fourth core is to be used for earthing.)	-	100	-
14.10.1(a)(Insulation Resistance test)	-	100	-
14.10.1(b)(High Voltage test)	-	100	-
14.10.1(c)(Measurement of stator resistance)	-	100	-
14.10.1(d)(No load test at rated voltage)	-	100	-
14.10.1(e)(Reduced voltage running up test at no load)	-	100	-
14.10.1(f)(Locked rotor)	-	100	-
14.10.1(g)(Breakaway (starting) torque)	-	100	-
14.10.1(h)(Leakage current test;)	-	100	-
14.10.1(j)(Temperature rise test at rated voltage)	-	100	-
14.10.1(k)(Temperature rise test at reduced voltage)	-	100	-
16.1.1(The pumpset shall be guaranteed for their performance of the nominal volume rate of flow and the nominal head at the guaranteed duty point. The overall efficiency of the pumpset shall be guaranteed at the declared duty point only.)	-	100	-
16.1.2(The guarantee shall be deemed to have been met with, if the measured values of head, volume rate of flow and overall efficiency are within the indicated in IS 11346 limits)	-	100	-
16.1.3(Open well submersible motor shall not get overloaded in the specified operating head range at rated voltage and supply frequency.)	-	100	-
16.1.4(The pump shall be tested for the operating head range as per 8.1.5.)	-	100	-
16.1.5(The overloading of motor is that condition when maximum current drawn by the motor exceeds the limit of 1.07 times of the rated motor current)	-	100	-
16.1.6(The tolerance shall apply to guaranteed duty point only.)	-	100	-
16.1.7(Performance at rated voltage and supply frequency is actual performance of the set. This is better than performance at rated speed, since in the entire operating head range speed of motor is higher than rated speed, as motor is running in under loaded condition.)	-	100	-
16.1.8(The manufacturer shall specify the minimum submergence of pump unit at duty point.)	-	100	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 7347 (1974)

Specification for performance of small size spark ignition engines

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.No.10.1.1(ISI Certification Marking )	-	1000	-
Cl.No.10.1(c)(Marking )	-	1000	-
Cl.No.10.1(b)(Marking )	-	1000	-
Cl.No.10.1(a)(Marking )	-	1000	-
Cl.No.9.1(h)(Reassembly ,Starting test and no load test)	-	2500	-
Cl.No.9.1(g)(Strip Examination)	-	5000	-
Cl.No.9.1(f)(Rating test after endurance test)	-	5000	-
Cl.No.9.1(h)(Reassembly ,Starting test and no load test)	-	3000	-
Cl.No.9.1(e)(Endurance test)	-	25000	-
Cl.No.9.1(d)(Starting test)	-	2500	-
Cl. No.9.1(c)(No load and Low speed test)	-	2500	-
Cl.No.9.1(a), Cl.No.9.3.1(Governing test)	-	3000	-
Cl.No.9.1(a)(Rating test including Fuel consumption test)	-	3500	-
15.4 (b)(Cold impact)	-	500	-
9.1(PIPE ENDS)	-	500	-

Complete

14 Jun, 2022

-
-

IS 10001 (1981)

Performance Requirements for Constant Speed Compression ignition (diesel) engines for general purposes (up to 20 kW)

0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.No.8(Test Certificate)	-	105000	Extra Lube oil and Fuel as per Actual uses
Cl.No.7.1(ISI Certification Marking )	-	1000	-
Cl.No.7(e)(Marking )	-	1000	-
Cl.No.7(d)(Marking )	-	1000	-
Cl.No.7(c)(Marking )	-	1000	-
Cl.No.7(b)(Marking )	-	1000	-
Cl.No.7(a)(Marking )	-	1000	-
Cl.No.4.2(Specific Fuel Consumption)	-	5000	-
Cl.No.3.1(d), Cl.No.3.5.2(Governing test)	-	5000	-
Cl.No.3.1(a)(Dimensional Measurenment for wear.)	-	10000	-
Cl.No.3.5.5(Lubricating Oil Consumption test)	-	5000	-
Cl.No.3.1(e)(Endurance test)	-	60000	-
Cl.No.3.1(b)(Preliminary run test)	-	5000	-
15.4 (b)(Cold impact)	-	500	-
9.1(PIPE ENDS)	-	500	-

Complete

14 Jun, 2022

-
-

IS 10002 (1981)

Specification for performance requirements for constant speed compression ignition (Diesel) engines for general purposes (Above 20 KW)

528000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.No.8(Test Certificate)	-	10000	-
Cl.No.7.1(ISI Certification Marking )	-	1000	-
Cl.No.7(e)(Marking )	-	1000	-
Cl.No.7(d)(Marking )	-	1000	-
Cl.No.7(c)(Marking )	-	1000	-
Cl.No.7(b)(Marking )	-	1000	-
Cl.No.7(a)(Marking )	-	1000	-
Cl.No.4.2(Specific Fuel Consumption)	-	20000	-
Cl.No.3.1(f), (Governing test)	-	30000	-
Cl.No.3.1(a)(Dimensional Measurenment for wear.)	-	30000	-
Cl.No.3.5(Lubricating Oil Consumption test)	-	25000	-
Cl.No.3.1(e)(Endurance test)	-	325000	-
Cl.No.3.1(b)(Preliminary run test)	-	50000	-
15.4 (b)(Cold impact)	-	500	-
9.1(PIPE ENDS)	-	500	-

Complete

14 Jun, 2022

-
-

IS 11170 (1985)

Specification for 1 performance requirements for constant speed compression ignition (Diesel) engines for agricultural purposes (Up To 20 KW)

105600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	100	For Type Test up to 20kW
8(Test Certificate)	-	2500	-
3.1(a) Preparation for tests according to IS : 10000 (Part 5)-1980)	-	2500	-
3.1(b) Preliminary run according to IS : 10000 (Part 5)-1980)	-	2500	-
3.1(c) Initial performance test according to Section I of IS : 10000 (Part 8)-1980 )	-	2500	-
3.1(d) Endurance test according to Section 1 of IS : 10000 (Part 9)-1980 )	-	86000	-
3.1(e) Final performance test according to Section 1 or IS : 10000 (Part 8)-1980;)	-	3000	-
3.1(f) Final inspection test according to IS : 10000 (Part 6)-1980 )	-	3000	-
3.1(g) Lubricating oil consumption according to IS : 10000 (Part 4)-1980.)	-	3000	-
3.1(Type test)	-	5000	-
3.1(e) Final performance test according to Section 1 or IS : 10000 (Part 8)-1980;)	-	3000	-
3.1(f) Final inspection test according to IS : 10000 (Part 6)-1980 )	-	3000	-
3.1(g) Lubricating oil consumption according to IS : 10000 (Part 4)-1980.)	-	3000	-
7(Marking)	-	100	-
8(Test Certificate)	-	500	-
3.1(Type test)	-	5000	-
3.1(a) Preparation for tests according to IS : 10000 (Part 5)-1980)	-	1000	-
3.1(b) Preliminary run according to IS : 10000 (Part 5)-1980)	-	250	-
3.1(c) Initial performance test according to Section I of IS : 10000 (Part 8)-1980 )	-	250	-
3.1(d) Endurance test according to Section 1 of IS : 10000 (Part 9)-1980 )	-	250	-
3.1(e) Final performance test according to Section 1 or IS : 10000 (Part 8)-1980;)	-	250	-
3.1(f) Final inspection test according to IS : 10000 (Part 6)-1980 )	-	250	-
3.1(g) Lubricating oil consumption according to IS : 10000 (Part 4)-1980.)	-	500	-
15.4 (b)(Cold impact)	-	500	-
9.1(PIPE ENDS)	-	500	-

Complete

14 Jun, 2022

-
-

IS 10805 (1986)

Specification for foot - Valves, reflux valves or non - Return valves and bore valves to be used in suction lines of agricultural pumping systems (First Revision)

6300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl. 2 Table 1)(Nominal Size)	-	500	-
(Cl. 2 Table 1)(Dimensions)	-	500	-
(Cl. 2 Table 1)(Dimensions)	-	500	-
(Cl. 2 Table 1)(Dimensions)	-	500	-
(Cl. 4)(Requirements)	-	500	-
(Cl. 4)(Requirements)	-	500	-
(Cl. 5)(Coating)	-	300	-
(Cl.6)(Testing)	-	1000	-
(Cl.6)(Testing)	-	1000	-
(Cl.6)(Testing)	-	1000	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 11501 (1986)

Specification for engine monoset pumps for clear, cold, fresh water for agricultural purposes

22680 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Material of Construction)	-	100	-
5.1(Gaskets, Seals and Packings)	-	100	-
6.1(Direction of rotation)	-	100	-
6.1(Direction of rotation)	-	100	-
7(Suction Limitations)	-	100	-
9.1(Design Features)	-	100	-
9.1(Design Features)	-	100	-
10.2(Casing)	-	1000	-
10.3(Impeller)	-	1000	-
10.4(Shaft)	-	1000	-
11.1(Engine Testing)	-	1000	-
11.2(Engine Testing)	-	1000	-
11.3.2.1(Pump Testing)	-	1000	-
11.3.2.2(Diesel Consumption)	-	1000	-
11.3.2.3(Pump Testing)	-	1000	-
11.4.2.1(Pump Testing)	-	1000	-
11.4.2.1(Pump Testing)	-	1000	-
11.4.2.2(Pump Testing)	-	1000	-
11.4.2.5(Pump Testing)	-	1000	-
14(MARKING)	-	1000	-
14(MARKING)	-	1000	-
14(MARKING)	-	100	-
14(MARKING)	-	100	-
14(MARKING)	-	100	-
14(MARKING)	-	100	-
14(MARKING)	-	100	-
14(MARKING)	-	100	-
14(MARKING)	-	100	-
14(MARKING)	-	100	-
15.4 (b)(Cold impact)	-	100	-
9.1(PIPE ENDS)	-	100	-

Complete

14 Jun, 2022

-
-

IS 1710 (1989)

Specification for pumps - Vertical turbine mixed and axial flow, for clear cold water (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 10.1(Max. Power at operating Head Range)	-	1000	-
Cl. 16.2(Guarntee of Performance (Pump Efficiency))	-	1000	-
Cl. 16.2(Guarntee of Performance (Power))	-	1000	-
Cl. 16.2(Guarntee of Performance (Discharge))	-	1000	-
Cl. 16.2(Guarntee of Performance (Head))	-	1000	-
Cl. 14.1(Pump Performance Test)	-	1000	-
Cl. 10.1(Design of Pump)	-	1000	-
Cl. 9.2.5.3(Line Shaft)	-	100	-
Cl. 9.2.3.3(Discharge case)	-	100	-
Cl. 9.2.3.2(Bowl)	-	100	-
Cl. 9.2.3.1(Bowl)	-	100	-
Cl. 9.2.2(Impeller)	-	100	-
Cl. 9.1.5.4(Thrust Bearing)	-	100	-
Cl. 9.1.5.3(Operating Speed)	-	100	-
Cl. 9.1.5.2(Engine Driven)	-	100	-
Cl. 9.1.5.1(Motor Driven)	-	100	-
Cl. 9.1.4(Submergence Required)	-	100	-
Cl. 9.1.2(Specification of Pump)	-	100	-
Cl. 8.2(Direction of Rotation)	-	100	-
Cl. 8.1(Direction of Rotation)	-	100	-
Cl. 9.2.4 (f)(speed)	-	100	-
Cl. 9.2.4 (e)(Head in meters/kW rating)	-	100	-
Cl. 9.2.4 (d)(Type of Impeller)	-	100	-
Cl. 9.2.4 (c)(Type)	-	100	-
Cl. 9.2.4 (b)(Serial number/year of manufacture)	-	100	-
Cl. 9.2.4 (a)(Name of Manufacturers)	-	100	-

Complete

14 Jun, 2022

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

8378 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	295	Include GST
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	295	Include GST
7.2(Reversion Test)	-	708	Include GST
7.3(Tensile Test)	-	1121	Include GST
7.3(Elongation at Break)	-	1121	Include GST
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1062	Include GST
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	944	Include GST
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	590	Include GST
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	800	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	2000	-

Complete

14 Jun, 2022

-
-

Bureau of Indian Standards

The National Standards Body of India

NSIC - Technical Services Centre

Aji Industrial, Bhavnagar Road, Opp Gujarat Forging, Rajkot, Rajkot, Gujarat, 360003

9959726692 [email protected]

Scope List