BIS - LIMS (Laboratory Information Management System)

CIPET MYSURU

437/A, Hebbal indl. Area, Mysuru, Mysuru, Karnataka, 570016

8124489163 [email protected]

Scope List

Reset

18 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

up to 400mm

19156 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.2(Resistance to External Blows at 0°C)	-	1050	Resistance to External Blows at 0°C
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	637.50	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	8250	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	375	Density
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	825	V S T
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	725	Reversion Test43
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	431.25	Opacity
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	225	VA
9.1(PIPE ENDS)	-	225	Pipe ends
8(SEALING RINGS)	-	0	Included
Clause 10.7(Sulphated Ash Content)	-	712.50	Sulphated Ash Content
7(DIMENSIONS-PIPE-Nominal Diameter)	-	375	All dim
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	Included
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	Included
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	Included
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	Included
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	Included
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	Included
7.2.1(DIMENSIONS-Socket)	-	5325	For EOW & Material

Complete

31 Dec, 2023

-
-

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

37063 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1 (Visual and Workmanship Requirement)	-	8587.50	All test missed include raw material
6.1.3.1.1(Weldability Test)	-	4800	All weld ability
6.1.3.2 (Quick coupled fittings)	-	6312	Quick coupled male & female couplers & Sprinklers
6.1.2.2( Hydraulic Proof Test)	-	4800	Pipe hydrostatics
6.1.1, 6.1.1.1(Leakage Test)	-	4800	leakage test
4.1.5(Rubber Ring)	-	7762.50	All rubber ring test

Complete

31 Dec, 2023

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

10869 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	825	VST
9.5(Tensile Strength IS 12235(Part 13))	-	1325	Tensile Strength IS 12235(Part 13)
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1125	Resistance to External Blows at 0 ?C IS 12235 (Part 9)
9.3(Density IS 12235 (Part 14))	-	375	Density IS 12235 (Part 14)
9.2(Internal Diameter)	-	262.50	Internal Diameter
9.1( Visual Appearance)	-	225	Visual Appearance
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	187.5	Dimensions of sealing elements
8.4(Sealing rings - Hardness)	-	281.25	Sealing rings - Hardness
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	187.5	THREADING OF SCREEN ANDCASING PIPES. IS 554.
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	750	Effective length, l2
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0	Wall thickness, Max included
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	Wall thickness, Min included in dim
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	0	Mean Outer Diameter over Connection included
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	Outer Diameter at any point included
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	0	DIMENSIONS - Casing Pipes included
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	5325	EOW, Raw material

Complete

31 Dec, 2023

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

upto 400mm diameter

38275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Polyethylene Resin)	-	1825	Polyethylene Resin MFI & DENSITY
5.3 (a)(Carbon Black Master Batch)	-	693.75	Carbon black content
5.3(b)(Carbon Black Master Batch)	-	525	Carbon black dispersion
5.3(c)(Carbon Black Master Batch)	-	1650	Thermal Stability (Oxidation Induction Time)
5.3(d)(Carbon Black Master Batch)	-	525	Volatile matter
5.3(e)(Carbon Black Master Batch)	-	525	Water content
8.3(Carbon black)	-	1219	CBC
8.6(Overall migration)	-	1575	Overall migration
6, 6.1(PIPE DESCRIPTION)	-	225	PIPE DESCRIPTION
6, 6.1.1(PIPE DESCRIPTION)	-	0	PIPE DESCRIPTION
6, 6.1.2(PIPE DESCRIPTION)	-	0	PIPE DESCRIPTION
6.1.3 (PIPE DESCRIPTION)	-	0	PIPE DESCRIPTION
6.1.4(PIPE DESCRIPTION)	-	0.01	PIPE DESCRIPTION
6.2(Colour)	-	225	Colour
6.2.1(6.1.1 Identification Stripes)	-	187.5	6.1.1 Identification Stripes
7.2(Length)	-	0	Length
7.4 table -3 & 4(6.1 Dimensions)	-	375	6.1 Dimensions
7.4.1.2(Ovality)	-	0	Ovality
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	16050	PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1200	Internal Pressure Creep Rupture Test of Pipe Joints
8.2(Longitudinal Reversion Test)	-	725	Reversion Test
8.4( Melt Flow Rate)	-	825	Melt Flow Rate
8.5 (Oxidation Induction Time)	-	1650	Oxidation Induction Time
8.7(Density)	-	1000	Density
8.8(Tensile Strength for Butt-fusion)	-	1325	Tensile Strength for Butt-fusion
8.9 table-6(Elongation at Break)	-	1325	Elongation at Break
8.1(Slow Crack Growth Rate)	-	4625	Slow Crack Growth Rate

Complete

31 Dec, 2023

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

HDPE woven sacks for packaging 50kg food grains

19117.50 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	187.50	Tapes – Width and Thickness ( IS 6192/IS 11197)
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	Tapes – Linear Density (IS 6192/IS 11197)
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	187.50	Tapes – Tenacity (IS 6192/IS 11197)
4.2 and Table 1 ii(Dimensions )	-	187.50	Dimension
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1500	Tapes – Dimensional stability (PP) (IS 11197) include identification
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12830	Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2650	Average breaking strength of fabric
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1325	Breaking strength of bottom seam
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	Elongation at break of fabric
4.2 and Table 1 x(Ash content )	-	712.5	Ash content
4.2 and Table 1 v(Mass of sack )	-	225	Mass of sack
5.2 and Table 1 iii(Ends per dm )	-	187.5	Ends per dm
5.2 and Table 1 iv(Picks per dm )	-	187.5	Picks per dm

Complete

31 Dec, 2023

-
-

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

Injection moulded PVC Socket fittings

4219 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	375	it will cover all dimension
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0	it will cover all dimension
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	it will cover all dimension
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	it will cover all dimension
Cl. 6.1(Stress Relief Test- Appendix A)	-	525	for stress relief
Cl. 6.2(Opacity- Appendix B)	-	431.25	for opacity
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	2250	for complete effect on water
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	for complete effect on water
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	for complete effect on water
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	for complete effect on water
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	637.50	for short term test

Complete

31 Dec, 2023

-
-

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	Thickness
2.2.3(socket length)	-	0	Included In Thickness
2.1(General)	-	525	Stress relief test
2.1(General)	-	431.25	Opacity
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	0	Included In Thickness
2.2.3( inside diameter of the socket)	-	5962.75	Included In Thickness Effect on water Rs.2250/- & hydro pressure test Rs.637.50 for pipes VCM Content -Rs. 2250/- & K Value Rs. 825/- for raw material

Complete

31 Dec, 2023

-
-

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	375	For Dimensions Thickness & Socket length)
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	2250	For EOW Including all element detection
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0	Included above
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	0	Included above
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	4668.75	EOW water charges included above, RS.1593 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2023

-
-

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	For all Dimensions
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	Included in dimensions
2.2.3( inside diameter of the socket)	-	0	Included in dimensions
2.2.3(Socket length)	-	0	Included in dimensions
2.1(General)	-	0	Included in next
2.1(General)	-	6918.75	RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2023

-
-

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	All DImensions
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	0	Included in above dimension charges
2.2.3( inside diameter of the socket)	-	0	Included in above dimension charges
2.2.3(Socket length)	-	0	Included in above dimension charges
2.1(General)	-	6918	RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2023

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	For All Dimensions
2.2.2, Table 1(Socket Laying Length)	-	0	Included in above dimension charges
2.2.3( inside diameter of the socket)	-	0	Included in above dimension charges
2.2.3(Socket length)	-	0	Included in above dimension charges
2.1(General)	-	0	Added in below charges
2.1(General)	-	6918.75	RS.3843 is for addition of (Stress relief test Rs. 525, Opacity Rs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2023

-
-

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	For All Dimensions
2.2.2, Table 1(Union Laying Length)	-	0	Included in above dimension charges
2.2.3( inside diameter of the socket)	-	0	Included in above dimension charges
2.2.3(Socket length)	-	0	Included in above dimension charges
2.1(General)	-	0	Added in below charges
2.1(General)	-	6918.75	RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2023

-
-

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.2(diameter of the socket of cap)	-	375		For All Dimensions
2.1(General)	-	6918.75		RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2023

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

13325 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.a (Potyethylene - higher olefins constituent )	-	5893.75	For All material & master compound Material Identification Rs.1500.00 Carbon Black Toluene extract Rs.825.00 Maximum volatile content Rs.525.00: Density Rs.1,000.00 : Melt Flow Rate Rs.825.00 :Carbon Black Content Rs.693.75 Carbon Black Dispersion
7.3(Tensile Test)	-	1075	For tensile & Elongation
7.3(Elongation at Break)	-	0.00	included in tensile
7.4(SusceptibiIity to Environmental Stress Cracking)	-	900.00	E s c r
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	187.50	For all dim
7.2(Reversion Test)	-	825.00	reversion Rs. 525 test & RS. 300 Specimen prep
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	4443.75	Dimension charges are included in above dimension charges Rs. 4443.7( Carbon Black Content Rs.693.75 Carbon Black Dispersion Rs.525.00 Visual Appearance Rs.225.00 , Hydraulic Acceptance Test 20°C/1hrs:Rs.750.00 Quality test 70°C/100 Rs.2,250.00

Complete

31 Dec, 2023

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

Upto 20000 litres

17144 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	693.75	CBC
4.2.3(Carbon Dispersion Test)	-	525	CBD
5(Types and Features )	-	1200	CL. 4.1.1 density & MFI
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	2512.50	5.1,5.2,5.3&5.4 & 6.1
7.1.1(Resistance to Deformation)	-	525	Resistance to Deformation
7.2(Resistance to Impact)	-	825	Resistance to Impact
7.3(Test for Top Load Resistance)	-	675	Test for Top Load Resistance
7.4(Tensile Strength)	-	1325	Tensile Strength
7.5(Flexural Modulus)	-	1325	Flexural Modulus
7.6(overall Migration)	-	7537.50	Cl. 7.6, 9.1, 8.2 & Raw material

Complete

31 Dec, 2023

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

11725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Dimensions of pipes)	-	187.5	All Dim
7(Visual Appearance)	-	225	VA
4(Colour)	-	225	Color
8.1(Hydraulic characteristics)	-	4800	Hydraulic characteristics
8.2(Reversion)	-	825	Reversion
8.3(Density)	-	375	density
8.4(Melt Flow Rate)	-	825	MFI
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	693.75	cbc
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	3568.75	All Materials & CBD

Complete

31 Dec, 2023

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

17563 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	825	MFI
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	2218.75	All raw material
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1218.75	CBC & CBD
5.1 table -1(DIMENSIONS OF PIPES)	-	375	All Dimension
5.1.2(Ovality)	-	0	Included in dim
6.1(VISUAL APPEARANCE)	-	225	VA
7.1 Table -2(Hydraulic Characteristics)	-	4800	Hydro
7.2(Reversion Test)	-	825	Reversion
7.3(Tensile Test)	-	1075	Tensile & Elong
7.4table-2(Fusion Compatibility Test)	-	4800	Fusion compatibility
7.5(Density)	-	325	DEnsity
7.6(Melt now Rate (MFR))	-	825	mfi

Complete

31 Dec, 2023

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

Films

24106.25 View breakup
Rs.14375/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	225	Test charges after 25% BIS Discount from our actual Approved charges
5.1.2(Film Form)	-	0	Test charges included In Appearance
5.1.3(Odour)	-	0	Test charges included In Appearance
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	375	Test charges after 25% BIS Discount from our actual Approved charges
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	825	Test charges after 25% BIS Discount from our actual Approved charges
5.1.6a(Carbon Black Content, Annex-A)	-	693.75	Test charges after 25% BIS Discount from our actual Approved charges
5.1.6b(Ash Content, Annex-A)	-	600	Test charges after 25% BIS Discount from our actual Approved charges
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	525	Test charges after 25% BIS Discount from our actual Approved charges
5.2.2(Tolerance on Thickness, Annex-A)	-	187.50	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	525	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	Test charges included In Tensile properties
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	Test charges included In Tensile properties
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	637.50	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	825	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tear resistence. B) Transverse direction )	-	825	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	525	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	Test charges included In Tensile properties
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	Test charges included In Tensile properties
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	637.50	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tear resistance , Annex B)	-	825	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Puncture resistance , Annex C)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tear resistance , Annex B)	-	825	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Puncture resistance , Annex C)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges

Complete

31 Dec, 2023

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET MYSURU

437/A, Hebbal indl. Area, Mysuru, Mysuru, Karnataka, 570016

8124489163 [email protected]

Scope List