BIS - LIMS (Laboratory Information Management System)

National Test House (NWR)

E 763, ROAD NO. 9F1, VKI AREA, Jaipur, Jaipur, Rajasthan, 302013

9414046288 [email protected]

Scope List

Reset

40 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 9873 : Part 9 (2017)

Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children's Products

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

- View breakup
Rs.5500/- for physical, Rs.1000/- for chemical

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

- View breakup
Rs.5500/- for physical, Rs.2500/- for chemical

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

XLPE insulated, PVC sheathed, armoured cable

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	--
15.1 a) iv)(Resistance test - Main conductor)	-	1500	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	500	-
9.2(Thickness of Insulation - Average)	-	500	-
9.3(Thickness of Insulation - Minimum)	-	500	-
14.3(Thickness of outer sheath - AVERAGE)	-	500	-
14.3(Thickness of outer sheath - minimum)	-	500	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	4000	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	500	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-

Complete

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

Outside Diameter 12, 16, 20, 25, 32mm

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	1500	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	1000	-
7.3(Tensile Test)	-	1000	-
7.3(Elongation at Break)	-	1000	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	2000	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	1000	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0	-
7.2(Reversion Test)	-	1000	-
7.1(Hydraulic Characteristics)	-	5000	-
6.1(Visual Appearance)	-	1000	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	0	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	0	-

Complete

-
-

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Fineness 4031 Part 2)	-	1000	--
6.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	1000	--
6.2.1.1(Expansion after aeration - 4031 Part 3)	-	1000	--
6.2.1(Expansion by Autoclave- 4031 Part 3)	-	1000	--
6.2.1.1(Expansion after aeration- 4031 Part 3)	-	1000	--
6.3 a)(Setting Time Initial- 4031 Part 5)	-	500	--
6.3 b)(Setting Time Final- 4031 Part 5)	-	500	--
6.4 a)(Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-	1500	--
6.4 b)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	--

Complete

-
-

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	500	-
7.1 Table-1(Dimensional measurement of wires)	-	500	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor )	-	500	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	500	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	500	-
9.1(Stranding)	-	500	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	-
9.3(Direction of Lay)	-	500	-
9.4(Multiple layers of wires)	-	500	-
11(Packing and Marking)	-	100	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	4000	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	4000	-
12.3 Table 1(Elongation Test- Before Stranding)	-	4000	-
12.3 Table 1(Elongation Test- After Stranding)	-	4000	-
12.4 Table 1(Resistance of Aluminium wire)	-	4000	-
9.2(Lay Ratio 24 wire layer)	-	500	-
9.2(Lay Ratio 18 wire layer)	-	500	-
9.2(Lay Ratio 12 wire layer)	-	500	-
9.2(Lay Ratio 3/6 wire layer)	-	500	-

Complete

-
-

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

10 to 560 sq, mm

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	4000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	4000	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	4000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	4000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	2000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	2000	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	2000	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	2000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	2000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	2000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	2000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	2000	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	4000	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	4000	-
13.7.2 (chem)(Mass of Zinc coating)	-	2000	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	500	-
13.9 (elec)(Surface condition test)	-	5000	-
13.10 (elec)(Ultimate breaking load)	-	5000	-
13.11 (elec)(Stress-strain test)	-	10000	-

Complete

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

- View breakup
Rs.9000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

-
Excluding: Antioxidant test (Cl.5.2) Up to 355 DN (mm).

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

63, 75, 90, 110, 125, 140mm and 160mm

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1000	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1500	-
5.1 table -1(DIMENSIONS OF PIPES)	-	1000	-
5.1.2(Ovality)	-	1000	-
6.1(VISUAL APPEARANCE)	-	1000	-
7.1 Table -2(Hydraulic Characteristics)	-	5000	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Test)	-	2000	-
7.4table-2(Fusion Compatibility Test)	-	5000	-
7.6(Melt now Rate (MFR))	-	1000	-
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	1000	-
Cl.7.4(Fusion Compatibility Test- b) Acceptance test)	-	5000	-
Cl.7.4(Fusion Compatibility Test- a) Quality test)	-	5000	-
Cl.7.3(Tensile Test - ii)Elongation at Break)	-	1000	-
Cl.7.3(Tensile Test- i) Tensile Strength)	-	1000	-
Cl 7.1(Hydraulic Characteristics - Acceptance test)	-	5000	-
Cl 7.1(Hydraulic Characteristics - Quality test)	-	5000	-
Cl.6(Visual Appearance)	-	1000	-
Cl.5(Dimensions of pipe - ii) Wall thickness maximum)	-	500	-
Cl.5(Dimensions of pipe - ii) Wall thickness minimum)	-	500	-
Cl.5(Dimensions of pipe - i) Outside diameter)	-	1000	-

Complete

-
-

Bureau of Indian Standards

The National Standards Body of India

National Test House (NWR)

E 763, ROAD NO. 9F1, VKI AREA, Jaipur, Jaipur, Rajasthan, 302013

9414046288 [email protected]

Scope List

No Record Found

No Record Found

No Record Found

No Record Found