BIS - LIMS (Laboratory Information Management System)

Central Institute of Petrochemicals Engineering and Technology (CIPET), BADDI

Plot No. 198/201, Inside VRLA Building, Near Biogenetic Pvt. Ltd., Jharmajri, Baddi, Baddi, Solan, Himachal Pradesh, 173205

8829039100 [email protected]

Scope List

Reset

18 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

All

22330 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (Fabric)	-	1050	-
4.2 (Fabric)	-	250	-
4.3(Sacks)	-	300	-
4.4(Seam)	-	250	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	1050	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	1100	-
4.7(Valve for Filling of Sacks)	-	250	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	400	-
4.5(Lamination )	-	500	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	500	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	2200	-
5/5.6 (UV Resistance, )	-	10180	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	2200	-
4.4(Seam)	-	2200	-

Complete

16 May, 2022

-
-

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

All

19630 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	-
4.2(Tapes – Linear Density )	-	500	-
4.3(Sacks)	-	300	-
4.3.1(Bottom Seam)	-	250	-
4.5 and Table 1 i(Capacity)	-	250	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	250	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	10180	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	-
5.2 and Table 1 x(Ash content )	-	950	-

Complete

16 May, 2022

-
-

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

All

10675 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Colour of fittings)	-	300	-
7.1,Table 1(Wall thickness)	-	500	-
8(Sealing Rings)	-	375	-
10(Workmanship)	-	300	-
11(Design requirements)	-	250	-
11.2(Socket and spigot configeration)	-	250	-
12.1(Visual appearance)	-	300	-
12.2(Stress relief test)	-	700	-
12.3(Vicat softening tempewrature)	-	1100	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	2500	-
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1200	-
Cl.15, Annex B(Sulphated Ash Content)	-	950	-
16.1(Impact test)	-	1100	-
17(Watet tightness of joint)	-	850	-

Complete

16 May, 2022

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

All

17100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	300	-
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100	-
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	-
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	300	-
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1000	-
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	-
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	-
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	-
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500	-
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1400	-
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	2700	-
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	-
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	700	-
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	1000	-

Complete

16 May, 2022

-
-

IS 14611 (2016)

Multilayered cross laminated sheets/tarpaulins/covers/agricultural films - Specification (First Revision)

All

38330 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1(Workmanship)	-	250	-
Cl. 6.2(Substance)	-	250	-
Cl. 6.4(water proofness test)	-	1000	-
Cl. 6.5(Strenght of joints/seams)	-	1100	-
Cl. 6.6(Flex test)	-	9000	-
Cl. 6.7(Ease of in-situ Repair)	-	250	-
Cl. 7.1(Eyelets and rope lashing)	-	250	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	2200	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	2200	-
Cl. 6.3(Accelerated ageing test)	-	4200	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- XLN Extra light)	-	2200	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- XLN Extra light)	-	2200	-
Table1 - v)(Dart Impact Strength)	-	850	-
Table1 - vi)(Average Tensile Strength & Elongation at Break after Exposing to UV Radiation & Weathering)	-	10180	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- XLN Extra light)	-	2200	-

Complete

16 May, 2022

-
-

IS 9755 (2016)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing fertilizers – Specification (fifth revision)

All

24080 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MANUFACTURE-Raw Material)	-	1050	-
3.2(MANUFACTURE-)	-	250	-
3.2(MANUFACTURE)	-	500	-
3.3(Sacks)	-	300	-
3.4(Liner)	-	1050	-
3.4.1(Liner)	-	250	-
3.4.1(Liner)	-	200	-
3.4.2(Lamination)	-	300	-
3.4.2(Lamination)	-	250	-
3.5(Bottom Seam-(see IS 10789).)	-	250	-
3.5(Bottom Seam-(see IS 10789).)	-	1050	-
3.7(Mouth of the Sack)	-	250	-
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	250	-
4.1 , Table 1(REQUIREMENTS)	-	250	-
4.1 , Table 1(REQUIREMENTS)	-	1000	-
4.2(UV Resistance)	-	2200	-
4.2(UV Resistance)	-	1100	-
4.2(UV Resistance)	-	10180	-
4.2(UV Resistance-The HDPE/PP woven fabric of sack made out of UV stabilized material shall have at least 50 percent of the original breaking strength when tested after the same has been exposed to UV radiation and weathering as per the method given in Annex D.)	-	2200	-
4.3(Mass-(Annexure E))	-	950	-
4.3(Mass-(Annexure E))	-	250	-

Complete

16 May, 2022

-
-

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

All

19980 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	1050	-
3.2(Tapes – Width )	-	250	-
3.2(Tapes – Linear Density )	-	500	-
3.4(Sack)	-	250	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	250	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	0	-
4.1 and Table 1 ii(Ends per dm )	-	250	-
4.1 and Table 1 iii(Picks per dm )	-	250	-
4.2 and Table 1 iv(Mass of sack )	-	300	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	1100	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	1100	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	10180	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	-
4.1 and Table 1 ix(Ash content )	-	950	-

Complete

16 May, 2022

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

All

19480 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	-
4.3(Sacks)	-	300	-
4.4 and Table 1 i(Capacity)	-	250	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
5.1 and Table 1 v(Mass of sack )	-	250	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	10180	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	-
5.2 and Table 1 x(Ash content )	-	950	-

Complete

16 May, 2022

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

All

41825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	250	-
6.2.1(6.1.1 Identification Stripes)	-	250	-
7.2(Length)	-	0	-
7.4 table -3 & 4(6.1 Dimensions)	-	500	-
8.5 (Oxidation Induction Time)	-	2200	-
6, 6.1(PIPE DESCRIPTION)	-	300	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	-
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	-
8.2(Longitudinal Reversion Test)	-	900	-
8.3(Carbon black)	-	1625	-
8.4( Melt Flow Rate)	-	1100	-
8.6(Overall migration)	-	2000	-
8.7(Density)	-	500	-
8.8(Tensile Strength for Butt-fusion)	-	1600	-
8.9 table-6(Elongation at Break)	-	1600	-
8.1(Slow Crack Growth Rate)	-	6000	-

Complete

16 May, 2022

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

50kg

23130 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250	-
3.3.1(Bottom seam (IS 10789))	-	250	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	250	-
4.2 and Table 1 ii(Dimensions )	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
4.2 and Table 1 v(Mass of sack )	-	300	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	10180	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	-
4.2 and Table 1 x(Ash content )	-	950	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	250	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1400	-

Complete

16 May, 2022

-
-

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

All

38975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1 (Visual and Workmanship Requirement)	-	300	-
4.1 .1.2.1(HDPE couplers)	-	1000	-
4.1 .1.2.2(HDPE couplers)	-	2200	-
Cl.4.1(Quick Coupled Male and Female Couplers)	-	925	-
Cl.4.1(Quick Coupled Male and Female Couplers)	-	3500	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	0	-
3(QUICK COUPLED PIPES)	-	19175	-
Cl.4.1.3(Workmanship and appearance )	-	1050	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	300	-
Cl 4.1.5(Rubber rings- A)Shore hardness (Shore-A))	-	375	-
Cl 4.1.5(Rubber rings- B) Change in hardness)	-	375	-
4.1.5(Rubber Ring)	-	4200	-
6.1.1, 6.1.1.1(Leakage Test)	-	850	-
6.1.2, 6.1.2.1( Hydraulic Proof Test)	-	850	-
6.1.3, 6.1.3.1(Weldability Test)	-	6400	-

Complete

16 May, 2022

-
-

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

All

26925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	-
10.1(Colour)	-	0	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	3000	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
Clause 10.7(Sulphated Ash Content)	-	950	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5850	-
11.2(Resistance to External Blows at 0°C)	-	1400	-

Complete

16 May, 2022

-
-

IS 10889 (2004)

High density polyethylene films (First Revision)

Grade-1 & 2

10900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials)	-	1600	500 density + 1100 MFI
5.2(Black Compound)	-	1625	925 CBC + 700 CBD
6.1.1(Appearance)	-	100	-
6.1.2(Film Form)	-	100	-
6.1.3(Odour )	-	100	-
6.1.4(Density)	-	500	-
6.1.5(Melt Flow Rate)	-	1100	-
6.1.6(Black Film)	-	1625	925 CBC + 700 CBD
6.2.1, Table 1(Nominal Thickness)	-	250	-
6.2.2, Table 2(Nominal Width)	-	250	-
6.3, Table 3(Yield Tolerance)	-	600	-
6.4.1(Tensile Strength at Break)	-	2200	MD & TD
6.4.2(Elongation at Break)	-	0	-
6.4.3(Impact Resistance (Falling Dart))	-	850	-

Complete

16 May, 2022

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

All

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.a (Potyethylene - higher olefins constituent )	-	1050	-
4.1.c.ii (Toluene extract - Annex A)	-	1100	-
4.1.c.iii (Volatile matter - Annex B )	-	700	-
4.1.c.i (Density)	-	1125	-
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	250	-
6.1(Visual Appearance)	-	300	-
7.1(Hydraulic Characteristics)	-	4000	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Test)	-	1350	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	-

Complete

16 May, 2022

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

Capacity upto 1000 litre

17150.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	1850	925 Tank + 925 Lid
4.2.3(Carbon Dispersion Test)	-	1400	700 Tank + 700 Lid
5(Types and Features )	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	250	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	250	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.3(Types and Features )	-	600	300 Tank + 300 Lid
5.4(Wall Thickness above effective height)	-	500	250 + 250 outer layer
6.1(Finish)	-	300	-
7.1.1(Resistance to Deformation)	-	700	-
7.2(Resistance to Impact)	-	1100	-
7.4(Tensile Strength)	-	1350	1100 + 250 specimen charges
7.5(Flexural Modulus)	-	1600	1100 + 500 Specimen charges
7.6(overall Migration)	-	2200	1700 + 500 Specimen charges
9.1(Man-Hole and Hand-Hole Lids)	-	1050	-
9.1(Lid Thickness)	-	250	-
9.2.1(Man-Hole and Hand-Hole Lids)	-	400	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	250	-

Complete

16 May, 2022

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

All

11475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Colour)	-	300	-
6(Dimensions of pipes)	-	250	-
7(Visual Appearance)	-	300	-
8.1(Hydraulic characteristics)	-	6400	-
8.2(Reversion)	-	1000	-
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1100	-
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	-

Complete

16 May, 2022

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

All

21400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1100	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	1125	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1625	-
5.1 table -1(DIMENSIONS OF PIPES)	-	500	-
6.1(VISUAL APPEARANCE)	-	300	-
7.1 Table -2(Hydraulic Characteristics)	-	6400	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Test)	-	1350	-
7.4table-2(Fusion Compatibility Test)	-	6400	-
7.5(Density)	-	500	-
7.6(Melt now Rate (MFR))	-	1100	-

Complete

16 May, 2022

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

Type I & Type II

22225.0 View breakup
Rs.13531/- for black film , Rs.3019/- extra for Black compound Rs.11600/- for natural film; Rs.1800/- extra for Natural compound

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	-
5.1.1(Appearance)	-	100	-
5.1.2(Film Form)	-	100	-
5.1.3(Odour)	-	100	-
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	500	-
5.1.6a(Carbon Black Content, Annex-A)	-	925	-
5.1.6b(Ash Content, Annex-A)	-	950	-
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	-
5.2.2(Tolerance on Thickness, Annex-A)	-	500	-
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1350	1100 + 250(Specimen Charges)
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1100	-
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4300	-
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1000	-
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1000	750 + 250 (Specimen Charges)
6.1, Table 1(Tear resistence. B) Transverse direction )	-	750	-
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1350	1100 + 250(Specimen Charges)
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1100	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4300	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	1000	-
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tear resistance , Annex B)	-	0	-
8.1, Table 3(Puncture resistance , Annex C)	-	0	-
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tear resistance , Annex B)	-	0	-
9.1, Table 4(Puncture resistance , Annex C)	-	0	-

Complete

16 May, 2022

-
-

Bureau of Indian Standards

The National Standards Body of India

Central Institute of Petrochemicals Engineering and Technology (CIPET), BADDI

Plot No. 198/201, Inside VRLA Building, Near Biogenetic Pvt. Ltd., Jharmajri, Baddi, Baddi, Solan, Himachal Pradesh, 173205

8829039100 [email protected]

Scope List